NBT EVO GPS Receiver
|
|
- Melvin Banks
- 5 years ago
- Views:
Transcription
1 NBT EVO GPS Receiver (with Nav/Voice and Video in Motion activation) Rev 1.2 BEFORE YOU START READ THE COMPLETE INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION IF YOU HAVE ANY QUESTIONS ABOUT THE USE OF THIS DEVICE, CONTACT YOUR BIMMER RETROFIT REPRESENTATIVE BEFORE USE Installation of NBT Evo GPS Receiver should be performed by an installer with appropriate knowledge and experience. We strongly recommend using services of professional installers, experienced with BMWs, for this installation. Battery should be disconnected prior to the installation for safety reasons. Reconnection of the battery should be done only after all electrical connections are in place. This manual covers installation of the NBT Evo GPS Receiver of two types: PNP and non-pnp versions.
2 Contents DEVICE OVERVIEW... 3 INSTALLATION OF NBT Evo GPS MODULE... 4 IS CODING REQUIRED IN YOUR CASE?... 8 FIRMWARE UPDATE MODE FOR GPS MODULE MANUAL FIRMWARE UPDATE MODE FOR THE GPS MODULE... 12
3 DEVICE OVERVIEW NBT Evo GPS Receiver with PNP cables NBT Evo GPS Receiver with non-pnp cables NBT Evo GPS Receiver with PNP harness Non-PNP harness for NBT Evo GPS Receiver
4 INSTALLATION OF NBT Evo GPS MODULE STEP 1 Remove NBT Evo head unit ( head unit ) from its position (but do not disconnect any of the wiring just yet). This will require you to remove some plastic trim on your dashboard and unscrew appropriate screws. Depending on the model of your BMW, you may need to switch transmission to Drive position, before removing the head unit (to give more space to maneuver). We also recommend that you place some protective blanket on the center console trim, to avoid possible scratches and dents. PNP Harness version installation steps (for all BMW F series) (skip to non-pnp harness version installation below if your version is non-pnp) STEP 2 1. Locate the main quadlock harness at the back of the head unit, as shown on the picture. Note that the colors of the wires connected to the harness may vary from one vehicle to another. Headunit in picture is shown for reference only.
5 2. Disconnect the quad lock connector from head unit and take a quick look at it. You will need a flat screwdriver in order to remove the MOST optical connector from the quadlock connector harness and re-plug it into the quadlock connector of the GPS module PNP harness. WARNING! It is important to reconnect this MOST optical cable in order to avoid loss of sound and other multimedia features. 3. Gently pull the plastic lock on the connector using a screwdriver and pull up the two optical cables. 4. Now re-plug this optical connector into the same position of the GPS PNP quadlock harness.
6 5. Connect the Main quadlock connector harness into the opposite end of the GPS PNP quadlock harness. STEP 3 Connect 12pin connector from PNP wiring harness to the GPS Receiver module. Make sure that connector plug is fully inserted in to the 12 pin connector at the GPS Receiver module. Non-PNP Harness version installation steps (whenever PNP harness does not fit) (skip this to STEP5 if your module is PNP) Non-PNP wiring is used when there is no way to fit PNP harness due to other PNP harnesses already installed between vehicle quadlock and headunit. For example in E series vehicles where PNP Plug version of enbt adapter is already installed.
7 STEP 4 Connect wires from non-pnp harness of GPS Receiver pin 1 to GND and pin2 to +12V supply. Connect wires from non-pnp harness of GPS Receiver pin 3 to CAN Low and pin 4 to CAN High lines. You may use wires at vehicle side quadlock connector: pin 12 for GND and pin 15 for +12V, pin 9 for CAN Low and pin 11 for CAN High. Make sure that wires are properly connected and isolated. It is recommended to secure wires to each other with tie-ups. Warning! GPS Receiver module may be configured for CAN 100kbit or CAN 500kbit speeds. When connecting CAN lines from non-pnp harness make sure to connect to appropriate CAN speed lines. For all E series BMWs when connecting to vehicle side quadlock connector make sure that GPS Receiver configured for CAN bus 100kbit speed. If connecting CAN lines to enbt adapter CAN2 side (headunit side) make sure that GPS Receiver configured for CAN bus 500kbit speed. STEP 5 Secure GPS Receiver module behind the dash with use of tie-ups or other type of mounting. Ensure that GPS Receiver module is secured and wiring attached to it is not blocking head unit path in the dash board. Normally at the back of the head unit tunnel in the dash board on the right or left side, there will be some opening. You may use that opening to install the GPS Receiver. This will let you install head unit properly to the end of the tunnel.
8 STEP 6 Connect OABR connector to NBT Evo OABR port. STEP 7 (RE-INSTALLING THE HEAD UNIT) Re-install your head unit inside the dash board. Follow the procedure which was used to remove headunit initially from the dash board. Warning! Avoid installing GPS Receiver module in direct contact with hot surfaces (head unit, vehicle heater, etc) because excessive heat may damage GPS Receiver. IS CODING REQUIRED IN YOUR CASE? If your GPS Receiver module is purchased together with the NBT Evo kit, its functionality should already be coded by BIMMER RETROFIT into the headunit. There is no need for additional coding, unless otherwise is stated by seller.
9 In case if your GPS Receiver retrofit adapter is purchased separately, there might be some coding required to have GPS feature working with NBT Evo. Please note that Evo headunit should be coded to your vehicle options list for proper functionality. The following two options must be coded in NBT Evo to switch it to external GPS mode: TELEMATIC_ECU: atm SYSTEM_GPS_RECEIVER: nicht_aktiv PNP Module Utility installation and use 1. PC utility and driver can be used with Windows7, Windows8 or Windows Installation of.net Framework 4.5 is required for proper operation of the utility. 3. Connect USB cable from GPS Receiver module to PC. 4. Install attached with the pack driver for the newly apeard USB device. For Windows 10 driver installation is not required as the driver will be installed automatically. 5. In your PC new Serial Port device under Ports will apear. Write down number of the COM port device which apeared in your system 6. Start utility program included in the pack. 1. Select COM port of GPS Receiver module which apeared in your system and click Connect button.
10 2. Utility should report about sucesfull connection and Connect button should become green. 3. Click Read Settngs button to see current adapter settings. 4. When you need to disconnect from the adapter click Online/Connect button again. Utility will disconnect from the adapter. 5. Button Factory Deafults will place adapter in Factory defaults mode. 6. Button Clear will clean up display of the utility. 7. Under Options selection drop down list you may select various options. Button Run Task will run selected task. 8. Options selection tasks: Firmware Update mode switch adapter to firmware update mode Read Current settings reads current adapter settings and show them on display Reset factory defaults Reset module to factory defaults CAN Speeds sets CAN speeds for adapter operation. User may change depends on installation type. There are maybe some other options and modes which are not supported by GPS Receiver since this PNP utility is a universal between few products.
11 FIRMWARE UPDATE MODE FOR GPS RECEIVER MODULE It is not supported on Mac computers yet. Sorry Mac owners, you have to use Windows PC for this update. Remove your headunit and get access to the GPS Receiver Module. Disconnect adapter from headunit or from vehicle wiring. Plug micro USB cable into the slot on the adapter. Whenever firmware update procedure is required please follow the following steps: 1. Connect to PNP Utility as described above in the manual using USB cable. 2. Select from drop down menu Firmware Update mode and press Run Task button 3. Make sure that you have received new firmware update file from manufacturer. 4. Open File Explorer. You will see that new disk drive appeared in the system. 5. Open newly appeared drive. You will see there is a file: firmware.bin 6. Delete this file from the drive. 7. Copy new firmware update file from your computer to the newly appeared disk drive. You should have only one! file on this drive now. Firmware update file may have a name
12 different from firmware.bin Usually firmware update file has a name which includes firmware version, however the file extension should be.bin. There is no need to rename new firmware update file back to firmware.bin It is important not to interrupt process of file copying during the firmware update. Also it is important to make sure that you copied the correct firmware update file, received from the manufacturer to your GPS Receiver module. You should copy to GPS Receiver module only firmware update file and not any other files. MANUAL FIRMWARE UPDATE MODE FOR THE GPS RECEIVER MODULE If for any reason your firmware update is not successful using the method above and your module can no longer enter the firmware update mode, you can use the Manual firmware update method described below. For the firmware update of the GPS Receiver Module you will need to have the following: 1. Micro USB to USB adapter cable 2. Standard pen or pencil 3. Computer with at least one USB port available and Windows system installed In order to perform the firmware update, following the steps: 1. Disconnect and remove GPS Receiver module from your vehicle. 2. Plug USB cable to your GPS Receiver Module. There is a small Micro USB connector on the side of the module.
13 3. Take a pen or pencil and use it to gently press a small button located on the side of the GPS Receiver Module, in the hole. This hole usually located next to the USB port depends on the module type and construction. Please do not push hard as it may damage the button. 4. While holding the button down, connect another end of the USB cable to your PC s USB port. 5. After short time (up to 10 seconds) you will see that new drive (G:) appeared under My Computer. This drive will have a name: CRP1 ENABLE. 6. Immediately release button as soon as you see drive appeared under My Computer. In your case it will most probably have a different letter (D:, E:, F:, etc.)
14 6. Newly appeared drive will contain a single file called: firmware.bin 7. Delete this file (firmware.bin) completely from the drive. 8. Copy new software update file which you received from us onto the drive G: 9. Once the file is copied disconnect USB cable from your computer. 10. Disconnect USB cable from GPS Receiver module and install module back to your vehicle. 11. Software update is now completed. Accessing service menu in NBT Evo to verify GPS functionality There is a hidden service engineering menu in NBT Evo headunit which provides some technical information useful for verification of the system functionality. In case if it is required to see current GPS status, visible satellites, GPS position lock, etc, you may access this service menu. Follow the steps below: 1. Press MENU button once to make sure that you are in main menu 2. Push and hold idrive controller for 10 seconds in Up forward position then release 3. Slowly rotate idrive controller knob exactly 3 clicks clockwise 4. Slowly rotate idrive controller knob exactly 3 clicks counterclockwise 5. Rotate idrive controller 1 click clockwise 6. Rotate idrive controller 1 click counterclockwise 7. Rotate idrive controller 1 click clockwise 8. Push idrive knob down and release it immediately 9. Headunit should stay in main menu, this indicates that steps 1-9 correctly done. If menu opened you have to repeat steps Open My Vehicle menu
15 11. Go to the very bottom and open *Service menu* 12. Go to Navigation menu and then open GPS menu. 13. Open GPS Status menu and see GPS Status message GPS Status: Check Antenna GPS Module is searching for satellites. GPS is not locked. Check your antenna, make sure it is connected to GPS Receiver. You should be outside with good sky visibility to get 3D lock. GPS Status: 3D Fix GPS Module found satellites and now has proper 3D locked position For all questions or other inquires please contact us at: or visit: Copyrighted Bimmer Retrofit Company. All rights reserved.
Pre-LCI F Series NBT (EVO) Retrofit Adapter
Pre-LCI F Series NBT (EVO) Retrofit Adapter (with MOST bus support) Rev 1.5 BEFORE YOU START READ THE COMPLETE INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION IF YOU HAVE ANY QUESTIONS ABOUT THE
More informationEasy (enbt) Retrofit Adapter Instruction Manual
Easy (enbt) Retrofit Adapter Instruction Manual Rev 2.06 BEFORE YOU START READ INSTRUCTIONS CAREFULLY BEFORE USE IF YOU HAVE ANY QUESTIONS ABOUT THE USE OF THIS DEVICE, CONTACT YOUR BIMMER RETROFIT REPRESENTATIVE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CASSETTE/MP3 (EX) 2006 PILOT All 30488 Issue Date SEP 2005 Player Attachment Kit (sold separately) : P/N 08B06-S9V-100A Cassette Player
More informationVehicle Applications. Features. Radio Compatibility. Note. Parts Included. Wiring Diagram
Vehicle Applications BMW 1 SERIES 2011 - Up 1 Series (5 Door) 2012 - Up 1 Series (3 Door) Features 3 SERIES 2012 - Up 3 Series Sedan 2012 - Up 3 Series Wagon 4 SERIES 2013 - Up 4 Series Coupe 2013 4 Series
More informationPRECAUTIONS: Please read before you start the installation
Installation manual for DVI HA HDD with HA HDD harness In the box: DVI HA HDD video interface HA HDD plug and play wiring harness Installation manual IMPORTANT: Please read all precautions first. This
More informationCourtesy of:discountcarstereo.com USB-CDR30. ation Guide for Porsche CDR30/31. Radios Revised: January 10, 2018
Courtesy of:discountcarstereo.com USB-CDR30 Quick Start Installation ation Guide for Porsche CDR30/31 Radios Revised: January 10, 2018 Introduction: Portable audio products are everywhere, reflecting demand
More informationGMNAV1 Advent Integrated Navigation
GMNAV1 Advent Integrated Navigation This interface is designed to integrate Navigation into select Buick and Chevrolet Systems. INSTALLATION MANUAL What s in the Box The following items are supplied with
More informationRexroth Controller Installation & Operations Manual
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Rexroth - 105 Controller Installation & Operations Manual The Drive & Control Company Table of Contents:
More informationfor the BIMMERTECH Multi Media Interface with HDMI inputs and additional video sources like front/rear cameras and SmartView mirroring devices
Installation Instructions for the BIMMERTECH Multi Media Interface with HDMI inputs and additional video sources like front/rear cameras and SmartView mirroring devices BMW F30/F80 Phone: +1(646) 439-7920
More informationSIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 SIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285 BHM Overview The SIR-PCM3 adds Sirius
More informationNNG-Ford V1 NTV-KIT558. Navigation interface for FORD vehicles equipped with 8.4 MyTouch NTV-DOC218
3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Ford V1 Navigation interface for FORD vehicles equipped with 8.4 MyTouch NTV-KIT558 NTV-DOC218 SoftTouch Navigation System
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. MP3 ATTACHMENT KIT 2006 RIDGELINE AII 28615 Issue Date FEB 2005 PARTS LIST Attachment Kit: P/N 08B06-SJC-100 MP3 Player Kit (sold separately):
More informationInstallation Instructions
Installation Instructions Page 1 of 18 November 2007 Communication, Hands-Free Version 6.0 Accessory Development These Installation Instructions supersede all previous versions. SUBJECT PHONE DOCKING CRADLE
More informationGAT Handheld Coder Pro+ User Manual
GAT Handheld Coder Pro+ User Manual Rev 1.2 READ INSTRUCTION CAREFULLY BEFORE USE IF YOU HAVE ANY QUESTIONS ABOUT THE USE OF THIS DEVICE, CONTACT YOUR BIMMER RETROFIT REPRESENTATIVE BEFORE USE HANDHELD
More informationPart Number: Lt. Taupe / Stone / Ivory Touring Edition Accessory Code: EH3
Part Number: Lt. Taupe - 00016-00710 / Stone - 00016-00720 / Ivory - 00016-00730 Touring Edition - 00016-00745 Accessory Code: EH3 Kit Contents Item # Quantity Reqd. Description 1 2 Headrest Assembly 2
More informationARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios.
Required for Install: ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios. 1. Chrysler/Dodge/Jeep vehicle with Uconnect
More informationVeNICE 2002 VeNICE 2002-PRO Range Rover L Bluetooth Audio Input Module
VeNICE 2002 VeNICE 2002-PRO Range Rover L322 2002-2005 Bluetooth Audio Input Module Thank you and congratulations for the purchase of the L322 VeNICE Bluetooth module! We are urged to remind you that any
More informationField Update Guide. for Raven Viper Pro
Field Update Guide for Raven Viper Pro Introduction The field update kit (P/N 117-0171-467) is designed to allow the Raven Viper Pro to utilize the automatic power down feature without returning the console
More informationJaguar F-TYPE CAM Dual Camera interface for select 14+ Jaguar vehicles NTV-KIT589
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 Jaguar F-TYPE CAM Dual Camera interface for select 14+ Jaguar vehicles NTV-KIT589 BHM Overview Jaguar F-TYPE CAM interfaces
More informationDVB-CCC/DVB-CIC. Compatible with BMW Professional navigation systems with idrive and 6.5 /8.8 monitor
dvblogic DVB-T Tuner DVB-CCC DVB-CIC Compatible with BMW Professional navigation systems with idrive and 6.5 /8.8 monitor Product features Full plug and play vehicle-specific dual DVB-T Tuner with two
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationTOYOTA LANDCRUISER IPOD INTERFACE Part Number: Accessory Code: RI3
TOYOTA LANDCRUISER 2009 - IPOD INTERFACE Part Number: 00016-00115 Accessory Code: RI3 Kit Contents Item # Quantity Reqd. Description 1 1 Digital interface box 2 1 Cable A 3 1 Cable B 4 1 Cable C 5 1 Hardware
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9011 Created 11/21/11 Kit Contents: Item # Qty. Component Description 1 2 Monitor Assembly 2 2 Remote Control 3 1 Cables # 3 4 1 Metal Wire Puller 5 1 Power Cord # 9 6 1 Owners Manual 7 2
More informationReplacement Instructions
imac G5 Inverter, 20-inch Replacement Instructions Follow the instructions in this document carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Online
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION MASKING TAPE
GUIDE PART NUMBER: 250-7616 GM SOFT TOUCH NAVIGATION SYSTEM GENERAL APPLICABILITY 2013- RAV4 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 NAVIGATION INTERFACE MODULE 2 1 VEHICLE INTERFACE T-HARNESS 3 1 LCD/GPS
More informationPN: A. ParaDyme System Auxiliary Harness Installation Guide
PN: 602-0259-01-A ParaDyme System Auxiliary Harness Installation Guide LEGAL DISCLAIMER The manufacturer disclaims any liability for damage or injury that results from failure to follow the instructions
More informationInstallation manual FISCON Pro Hands free kit BMW
Version 1.07 Installation manual FISCON Pro Hands free kit BMW Article-ID 37663 37663-1 www.kufatec.de Kufatec GmbH & Co. KG Dahlienstr. 15 23795 Bad Segeberg e-mail: info@kufatec.de Content General advice...
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Chrysler/Dodge/Jeep Remote Add-On CD player for RA1, RA2, RA3, or RA4 radios (Kit # 5000-8750) 2013-current RAM truck and Viper; 2015-current Charger, Challenger, and 300; 2017 Pacifica Please read thoroughly
More informationAg Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series
Note: Indented items indicate parts included in an assembly listed above. Part Name / Description Part Number Quantity Direct Command Spra-Coupe 7000 Kit 4100531 1 Liquid Product Control Module 4000394
More informationCI-C1-CCC CI-C1-CIC/CI-C1-CXC-TV1 CI-C1-E65/CI-C1-E65-TV. Compatible with BMW Professional navigation systems with idrive and 6.5 /8.
c.logic lite interfaces CI-C1-CCC CI-C1-CIC/ CI-C1-E65/CI-C1-E65-TV Compatible with BMW Professional navigation systems with idrive and 6.5 /8.8 monitor Interface-set AV and reverse camera input with device
More informationXPS 15 2-in-1. Service Manual. Computer Model: XPS Regulatory Model: P73F Regulatory Type: P73F001
XPS 15 2-in-1 Service Manual Computer Model: XPS 15-9575 Regulatory Model: P73F Regulatory Type: P73F001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better
More information12.3 Pro Dash Quick Start Guide
12.3 Pro Dash Quick Start Guide 553-111 CONTENTS: Package Contents... 3 Mounting... 3 Connections... 4 Main Connector... 4 CAN Extension Harness... 6 USB... 7 GPS Antenna... 7 Cleaning... 7 Touchscreen
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationInstallation Guide. Version: 5.6 (Digitax) April 2016
Installation Guide Version: 5.6 (Digitax) April 2016 STEP SUMMARY PAGE 1 Fit Mounting Bracket and Antenna 5 2 Connect Loom to Vehicle 6 3 Connect Screen to Loom 8 4 Configure SmartMove 9 5 Test SmartMove
More informationIn2digi D-MB-2 Installation Instructions. There are 3 parts to installing the in2digi D-MB-2 in Mercedes Benz vehicles
In2digi D-MB-2 Installation Instructions There are 3 parts to installing the in2digi D-MB-2 in Mercedes Benz vehicles 1) Install the Antenna 2) Configure the Audio system to enable DAB 3) Install the D-MB-2
More informationipod Expand Your Factory Radio NISSAN/INFINITI add
Expand Your Factory Radio Harness Connection add ipod Dip Switches Port 1 Port 2 (See Manual) USB NISSAN/INFINITI 370z Cube Pathfinder Armada Sentra Maxima Altima Rouge Versa G35 M35/45 QX56 Murano Owner
More informationNavigation interface for Jeep GC 5 RA2 NTV-KIT581
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Jeep GC Navigation interface for Jeep GC 5 RA2 NTV-KIT581 NNG-JEEP GC Kit Content 5 1 6 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8.
More informationJaguar F-TYPE CAM 16. Dual Camera interface for select 16+ Jaguar vehicles NTV-KIT746 BHM 05/31/16 NTV-DOC259
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 Jaguar F-TYPE CAM 16 Dual Camera interface for select 16+ Jaguar vehicles NTV-KIT746 BHM Overview Jaguar F-TYPE CAM 16 interfaces
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationBMW-EVO KIT NTV-KIT804
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW-EVO KIT NTV-KIT804 Screen Connector Overview The BMW-EVO kit interfaces 2 video inputs (including
More informationHARMONi G3. Quick Start Guide for HARMONi G3. imac Processor/FireWire Upgrade
HARMONi G3 imac Processor/FireWire Upgrade imac and Operating System Compatibility The HARMONi G3 imac processor/firewire upgrade is compatible only with imac 233, 266, and 333 MHz models (Revisions A-D);
More informationDODGE Challenger Charger Journey. 6-Pin Video Input Cable 6-Pin Audio In/Out Cable GPS Magnetic Antenna
CHRYSLER 2011-2014 300c DODGE 2011-2014 Challenger 2011-2014 Charger 2011-2014 Journey FIAT 2011-2014 Freemont Plug and Play connectors make installation simple and easy. Utilizes the latest mapping version
More informationW205-RVC NTV-KIT580. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W205-RVC NTV-KIT580 Overview The W205-RVC Kit allows the user to add a backup camera input (with
More informationEH50 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF
Toyota 4Runner 2011 - Dual Player Headrest Video Part Number: 00016-00360; Sand Beige 00016-00370; Black Accessory Code: EH50 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF
More informationBMW12-DYNAMIC KIT NTV-KIT462
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW12-DYNAMIC KIT NTV-KIT462 Overview The BMW12 kit allows the user to add up to 3 video inputs
More informationv.logic Intelligent Solution Interface V4-CCC
v.logic Intelligent Solution Interface For the E-series BMW and Mini with navigation system or radio and 6.5 or 8.8 monitor with 10pin BMW LVDS connector Product features Plug and play media-controller
More informationHard Drive user manual
Hard Drive Docking Kit user manual Models 451147 & 451154 Model 451147 Model 451154 MAN-451147/451154-UM-0408-01 introduction Thank you for purchasing the MANHATTAN Hard Drive Docking Kit, Model 451147
More informationUCIT LIVE HD 4 Camera DVR. Installation Manual. 10/17 Version 2.0
UCIT LIVE HD 4 Camera DVR Installation Manual 10/17 Version 2.0 This is a step by step guide that will walk you through installing the UCIT LIVE HD 4 Channel Camera System. Basic wiring experience and
More informationQuick Installation Guide
Manual# 1140131 Quick Installation Guide Gateway NMEA2000/J1939 Quick Installation Guide for Gateway NMEA2000/J1939 ~~~ Printed May 2016 Revision Revised www.auto-maskin.com Copyright 2013-2016 by Auto-Maskin
More informationReflowing Xbox 360 Motherboard
Reflowing Xbox 360 Motherboard Reflow the solder on your Xbox 360's motherboard. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Use this guide to reflow the solder
More informationHow to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit
Instructional Video Series How to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit Skill Level: Challenging Time to Complete: Approximately 45 Minutes Required
More informationASUS D550MA-DS01 Motherboard
ASUS D550MA-DS01 Motherboard Replacement This guide will show you how to remove the motherboard from the laptop. Steps included in this process are removing the screws, disconnecting cables, and removing
More informationSimple Instructions for 808 HD Car Key Micro Camera (#16)
Simple Instructions for 808 HD Car Key Micro Camera (#16) Thank you for your purchase of our 808 Car Key Micro-camera (#16). If this is the first time you are using a product of this kind, please follow
More informationBMW12N-DYNAMIC KIT NTV-KIT717
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW12N-DYNAMIC KIT NTV-KIT717 Screen Connector Overview The BMW12-N kit interfaces 2 video inputs
More informationPRE-INSTALL QUESTIONS
PRE-INSTALL QUESTIONS Is it really Plug and Play? Yes. The Navos comes with all the necessary plugs and harnesses to connect directly to your car; no extra adapters or dash trim kits required. Is the Navos
More informationInspiron Service Manual. 2-in-1. Computer Model: Inspiron Regulatory Model: P69G Regulatory Type: P69G001
Inspiron 13 5000 2-in-1 Service Manual Computer Model: Inspiron 13-5378 Regulatory Model: P69G Regulatory Type: P69G001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps
More information* C29* 68P81084C29-0 RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS. Conversion From Dash/Local Mounting To Remote Mounting
Conversion From Dash/Local Mounting To Remote Mounting RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS Kit Number H634( ) for Model I Radio Kit Number H635( ) for Model II and Model III Radios Introduction
More informationRSNAV.com CarPlay interface for 3G MMI (B8)
Version 1.0 Warning: Professional installation recommended. Mask the working trim surfaces properly, otherwise, it will be scratched easily while installing! 1. Installation 2. Using, VW radio removal
More informationDirect Injection Module
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part number Quantity DirectCommand Kit 4100571 1 Module Mounting Hardware Kit 2001354-1 1 Installation Instructions
More informationDell XPS 14z Owner s Manual
Dell XPS 14z Owner s Manual Computer model: L412z Regulatory model: P24G series Regulatory type: P24G001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better
More informationDirectCommand Installation DirectCommand Complete Wiring Harness
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number With Switch Box Quantity by Model With Boom Switch Cable Display Cable Kit 4100814 1 1 Power Control
More informationNNG-Toyota 6. Navigation interface for Toyota Sienna NTV-KIT625 BHM 11/02/15 NTV-DOC237
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Toyota 6 Navigation interface for 15-16 Toyota Sienna NTV-KIT625 BHM 11/02/15 NTV-DOC237 Toyota 6 navigation system application
More informationInstallation Guide. Version: 6.1 (Digitax 4G) July 2018
Installation Guide Version: 6.1 (Digitax 4G) July 2018 STEP SUMMARY PAGE 1 Fit Mounting Bracket and Antenna 5 2 Connect Primary Loom to Vehicle 5 3 Connect Secondary Loom to Vehicle 8 4 Connect Screen
More informationAg Leader Technology. DirectCommand Installation Hardi 20-pin Interface Kit (Sprayer Chassis Mount)
Part Name / Description Part Number Quantity DirectCommand Hardi Sprayer Kit 4100882 1 Dust Receptacle 8-pin 2002975-8C 1 Installation Instructions 2006335 1 Quick Reference Card- Liquid Application 2002831-38
More informationNote: These installation instructions are only for the 4430/4440 Sprayer. For other SPX models please refer to P/N , &
DirectCommand Installation Ag Leader Technology Note: These installation instructions are only for the 4430/4440 Sprayer. For other SPX models please refer to P/N 2005944, 2005945 & 2006383. Part Name/Description
More informationMac Mini Model A1176 SSD Dual Drive
Mac Mini Model A1176 SSD Dual Drive Installation Trade your optical drive for a second hard drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 16 INTRODUCTION Use this guide to trade your
More informationDisplay Unit User Manual
Display Unit User Manual Contents 3 Specifications 3 Display Specifications 3 Absolute Maximum Ratings 3 Characteristics 4 Get started 4 Wiring 5 Application interface 5 Firmware upgrade 8 Settings 9 Display
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationFord Vehicles equipped with 8 MyFord Touch SYNC2 System Navigation Upgrade
2013-2016 Ford Vehicles equipped with 8 MyFord Touch SYNC2 System Navigation Upgrade S1C042A-Y01E Installation and User Manual Disclaimer Please read this manual thoroughly prior to installation. This
More informationInstructions for SVC-KIT-0020
Kaleidescape, Inc. July 22, 2010 Instructions for SVC-KIT-0020 Title Time to complete 1U Server Power Supply Replacement 1 hour Procedure to complete Locate Parts and Tools Service Kit Parts Power supply
More informationComputer Assembly (Installing Mother Board & CPU)
Computer Assembly (Installing Mother Board & CPU) IT@SCHOOL HARDWARE TEAM Biju Thiruvananthapuram Sree Kumar Kottarakkara Shamsudeen Attingal Pradeep Mattara Wandoor Pre-Installation Precaution Mother
More informationBMW / Mini. X SERIES Up X1 Sports Vehicle X5 Sports Activity Vehicle X6 Sports Activity Coupe
BMW / Mini 1 SERIES 2007-2011 1 Series 3-door hatchback 2007-2013 1 Series 2-door Coupe (1M) 2004-2012 1 Series (5-door) 2008 - Up 1 Series Convertible 3 SERIES 2005-2011 3 Series Sedan 2005-2011 3 Series
More informationIG601 Intelligent Gateway Quick Guide
IG601 Intelligent Gateway Quick Guide www.inhandnetworks.com Version v1.6 July 2017 1 / 26 Contents 1. PRODUCT INFORMATION... 3 1.1 STANDARD ACCESSORIES... 3 1.2 OPTIONAL ACCESSORIES... 3 2. PHYSICAL LAYOUT...
More informationPLMR18 OWNER S MANUAL. Mobile Audio System.
PLMR18 OWNER S MANUAL Mobile Audio System PLL Synthesizer Stereo Radio Automatic Memory Storing Preset Equalization USB/ SD Interface 3.5mm Jack input www.pyleaudio.com 1 CONTENTS Installation... 3 Take
More informationInstallation Manual. for Mobile Link Adapter for Liquid-cooled Generators
Installation Manual for Mobile Link Adapter for Liquid-cooled Generators for use with Mobile Link Unit Reference all appropriate documentation. This manual should remain with the Mobile Link unit. Table
More informationJippo Play - Installation Manual Page 1 INSTALLATION MANUAL. Intro Camera Operation Installation - Wrangler JK... 2
Jippo Play - Installation Manual Page 1 INSTALLATION MANUAL CONTENTS Intro... 1 Camera Operation... 2 Installation - Wrangler JK... 2 Jippo Play Configuration... 6 VES Installation... 7 Camera Installation...
More informationAg Leader Technology. DirectCommand Installation GVM Cab Kit (MY 2007 and Up) Important Notices
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100579 1 Cable Installation Kit 2000901-1 1 Dust Plug Deutsch 12
More informationChapter 3 Installation
Installation Chapter 3 Installation This chapter will guide you through the installation of your I/ O Extension A.3 board. It includes instructions on how to set the I/O port address and interrupt request
More informationFDS3NAV2. For Ford Vehicles Equipped With SYNC3. Installation Instructions. Calibration and Setup Guide. Page 1 of 14
FDS3NAV2 For Ford Vehicles Equipped With SYNC3 Installation Instructions Calibration and Setup Guide Page 1 of 14 Please read this manual thoroughly before installation. This manual illustrates a typical
More informationDisconnect the battery to ensure there will be no shorted wires during the installation procedure.
The round-style headunit receiver radio features Bluetooth technology allowing music to wirelessly stream from your compatible Bluetooth-enabled device. Control the audio from a distance -- all from your
More informationPlasma Retrofit Guide Upgrade Kit Installation Instructions
Upgrade Kit Installation Instructions 1. TMC 3-in-1 Installation 1.1 Unplug the power cable from your CPR800 Control Unit and open the lid. Note The pictures show a NEMA 23 CRP800 Control Unit but the
More informationDell OptiPlex All-in-One. Stand Installation Guide
Dell OptiPlex All-in-One Stand Installation Guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates
More informationipod Owner s Manual Expand Your Factory Radio VOLKSWAGEN Media Gateway PXAMG PGHVW2 Media Gateway add PXAMG
R Expand Your Factory Radio add ipod VOLKSWAGEN Owner s Manual Owner s Manual Media Gateway PXAMG Media Gateway PGHVW2 PXAMG Peripheral Electronics, a division of AAMP of America 13160 56th Court Clearwater,
More informationNOTICE OF INTENDED INSTALLATION AND USE
NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE
More informationPower Xpert Meter 2000 Gateway Card Kit
Quick Start Guide IL02601011E Rev. 2 December 2011 PXM 2250 PXM 2260 IQ 250 IQ 260 Power Xpert Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service.... 2 Disconnect Power Connections,
More informationMotion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure
Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure 2008 Motion Computing, Inc. All rights reserved. This document contains information protected by copyright. No part of this document may be reproduced
More informationPowerView Model PV1000. Hardware Installation Manual Section 78
PowerView Model PV1000 Hardware Installation Manual 00-02-0599 07-19-07 Section 78 In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications
More informationW205-N RVC NTV-KIT703
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W205-N RVC NTV-KIT703 Overview The W205-N RVC Kit interfaces a backup camera input (with active
More informationParts Identification Page 1 Vehicle Preparation Page 3 Programming Switch Settings Page 3 Installation Page 4. Form #5420,
SoftTouch Navigation System 250-7613 2012-2013 Toyota Camry Installation Instructions General Applicability: Toyota 2012-2013 Prius/Prius V, 2013 Venza, 2013 Avalon, 2013 Highlander, 2013 Tacoma For video
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationVANTAGE CL1. Installation and use of the CL1 Karting Data Kit
Installation and use of the CL1 Karting Data Kit Table of Contents What s in the box 3 Items needed for installation 4 CL1 registration 5 D3 app install 6 Battery installation 7 Mounting the CL1 data box
More informationChapter 1 Getting Started
Chapter 1 Getting Started Installation Instructions 1.1 Subject The NEO AUX adapter an integration between an MP3 player and a factory installed car stereo. Equipped with the specific vehicle harness and
More informationCourtesy of:discountcarstereo.com. This radio is for illustration purposes only BLU-BKR235. Quick Installation Guide for Becker AUX.
Courtesy of:discountcarstereo.com This radio is for illustration purposes only BLU-BKR235 Quick Installation Guide for Becker AUX Ready Radios Created June 19, 2015 Revised: January 15, 2018 Introduction:
More informationKeypad Lock. Operation and Service Manual. Order parts online
Keypad Lock Order parts online www.follettice.com Operation and Service Manual 801 Church Lane Easton, PA 18040, USA Toll free (800) 523-9361 (610) 252-7301 Fax (610) 250-0696 www.follettice.com 00163345R00
More informationBack Tilt Sensor Repair Kit [ ]
Back Tilt Sensor Repair Kit [002-1377-00] Components: Potted Tilt Sensor & Harness...1 Cable Ties...8 Step 1: Position chair. A) Press chair up control button to raise chair seat approximately 26-28 above
More informationRoyal RVV-500 (B) Retrofit Kit
Optipay BV/RC/CC into a Non-Fascia Vending Machine This document contains information for installing and configuring the JCM Optipay DBV-01 Bill Validator, RC-10 Bill Recycler and A-66 Coin Changer into
More informationOwner s Manual PXAUX. Add Auxiliary Audio to Your Factory Radio
Add Auxiliary Audio to Your Factory Radio Owner s Manual PXAUX isimple A Division of AAMP of America 13190 56th Court Clearwater, FL 33760 Ph. 866-788-4237 support@isimplesolutions.com 2012 AAMP of Florida,
More informationRS3000 SERIES BILL ACCEPTORS
Flash Diagnostic Codes RS3000 SERIES BILL ACCEPTORS INSTALLATION GUIDE s of the bill acceptor. Below is a chart that lists all the flash codes of the RS3000 Bill Acceptor and a description of each code.
More informationRAIN BIRD RC-4Bi, RC-7Bi, RC-1260Bi SERIES INSTRUCTION MANUAL
RAIN BIRD RC-4Bi, RC-7Bi, RC-1260Bi SERIES INSTRUCTION MANUAL DESCRIPTION OF CONTROLS Refer to Figure 1 Figure 1 A. HOUR DIAL with 23 CYCLE START PINS The HOUR dial contains 23 pins for rescheduling automatic
More information