USER SPECIFICATION FOR A VANDAL-RESISTANT KEYBOARD with a deported electronic unit CLAV (3 relais 12 volts)

Transcription

1 USER SPECIFICATION FOR A VANDAL-RESISTANT KEYBOARD with a deported electronic unit CLAV (3 relais 12 volts) This waterproof and vandal-resistant digicod is manufactured with an inox keyboard and with a deported unit. This is connected to the keyboard by a 5 meters cable. The electronic unit allow an optimal security to the CLAV200, because if the cable is destroyed, no access is possible. This keyboard is used in lifts, parking and so on). Also, a clock input, if you want, allow to accept the access only on definited hours. Our CLAV200 is processed according to CE normalisation. Technical specifications : Waterproof and vandal-resistant keyboard (IEC agreement) 2 millions working gold contacts Front panel programming- 4 or 5 digits codes Number of relais : 3 relais 48 codes Keyboard / electronic unit connexion cable : 5 meters Power supply : 12V AC / DC Consumption : 200 ma max Integrated buzzer back the front end Led : 1 red 1 green Relay contact : 10A 250 V, 1 to 99 sec. Delayed or bistable Memory retention even without current. Clock input to accept access only at exact definited hours Opérating temperature : - 25 C to 70 C Protection : Vandal-resistant screws with an unseat key included Opening door input terminal blocks ( for building input) Keyboard sécurity : An access code ( 4 or 5 digits) must be introduced in less than 10 seconds. The master code must be introduced in 16 seconds maximum. If you have passed more than 16 seconds, you will hear the 4 BIP explaining that your code is wrong. Then, it's necessary to introduce the code again. If you have introduced five false codes, the keyboard will be off during 10 seconds. Our CLAV200 has passed, with success, the electromagnetics compatibility tests. This key is manufactured according to the CENELEC directives and generic standards: NF EN & (immunity tests) NF EN & (emission tests). 1

2 The keyboard is factory programmed as follow : Factory code Master factory code : Relay number 1 delay : 3 seconds Relay number 2 delay : 3 seconds Relay number 3 delay : 3 seconds Number of digits by code : 5 «0» touch opening the door : No Explanation of BIP heared 1BIP : Programming mode status 2 BIP : Programming validation 4 BIP : Programming error or false code WARNING : For a correct keyboard programming, it's necessary to enter all differents codes by following methodically points 1 to 6 in serial order. On first programming or if you have lost your master code, you must connect electrically the two factory terminal blocks pins (US). 1 MASTER CODE PROGRAMMING KEYBOARD PROGRAMMING The master code allow to be in programming mode. You must check that the 2 factory connector pins (US) are connected. Then you maintain pushed the «A» key more than 4 seconds. 2 BIP hear indicate that you are in programming mode. Then, you introduce on the keyboard the factory code You will hear 1 BIP. Then you will take off the connection between the two factory connector pins (US). This allow to leave the factory mode. Warning : If you maintain the 2 factory connector pins, your keyboard will keep factory parameters with: factory master code, 5 numbers access codes and a 3 seconds delay. Enter the 48 adress numbers and then you will enter your new user master code (8 digits). The master code can't be used as your master code, it only allows to erase the former code. To register your code : Push shortly on «A» key. You will hear 2 BIP confirming your good programming. 2 DELAY PROGRAMMING You enter the number 50 as adress for the n 1 relay delay. You will hear 1 BIP. Then enter one number choised among 01 and 99, according to the seconds delay. If you choose 00 you will be in a two steady mode. (ON/OFF). To register your delay : Push shortly the «A» key. You will hear 2 BIP confirming your good programming. You will do the same for n 2 and 3 relays with: n 51 adress for the n 2 relay delay. n 52 adress for the n 3 relay delay. 3 Programming of the codes digits number: Each entering code is made by 4 or 5 digits. Enter the number 49 as adress. You will hear 1 BIP.Enter the number 4 if you retain a 4 digits code or the number 5 if you retain a 5 digits code : Then you shortly push the «A» key. You will hear 2 BIP confirming your good programming. 2

3 4 Programming your access codes You enter an adress numberbetween 00 and 47 (see the table below), you will hear 1 BIP, then you will enter your 4 or 5 access code digits. To register your access code : Push shortly «A» key. You will here 2 BIP confirming your good programming. Then you will pursue this step procedure to enter your others access codes. PS : The 0000(0) access code is forbidden, allowing only to erase an existing access code. Adress codes 00 to 09 : Relay n 1 Codes 39 to 41 : Relay n 1 if the clock input is activated Adress codes 10 to 19 : Relay n 2 Codes 42 to 44 : Relay n 2 if the clock input is activated Adress codes 20 to 29 : Relay n 3 Codes 45 to 47 : Relay n 3 if the clock input is activated Codes : 30 to 32 to connect simultaneously the n 1 and n 2 relais Codes : 33 to 35 to connect simultaneously the n 2 and n 3 relais Codes : 36 to 38 to connect simultaneously the n 1, n 2 and n 3 relais 5 - «0» key sélection as an opening door switch If the clock pin (H) is connected, we can allow the n 1 relay access by acting on «0» key. You enter the number 54 as adress. 1 BIP is heared. If you push the «0» key this function will be off. If you push the «1» key this function will be on. Then push shortly the «A» key. You will hear 2 BIP confirming your good programming. 6 Have you finished your programming sequence? If YES : Push again on «A» key. 2 BIP hears confirming that you have leaved the programming mode. If NO: because you would like to modify one code, your keyboard being always in the programming mode status, enter your adress code according your change wished. MODIFICATION OF AN ALREADY PROGRAMMED KEYBOARD You maintain pushed the «A» key more than 4 seconds.2 BIP hears indicate that you are on programming mode. Then you enter your own installant master code. You will hear 1 BIP. Enter the adress code with the modification. Then you will continue the sixth step procedure to keep out from the programming mode. ERASING ALL THE MEMORY Warning : You must use this function with caution. If necessary, you will connect the BP and CM pins. The n 1 LED will light on a short time. Then you push the «A» key more than 4 seconds. 2 BIP hears confirming that you are in programming mode. Then enter your own installant master code. You will hear 1 BIP. You will hear after, 6 low BIPS notifying that all the memory will be erased. Some seconds later, you will hear 2 BIP informing that all the memory has been erased. If you want to stop the erasing, you have to cut off the power supply during the 6 low BIPS. When you have finished the memory erasing, you have to disconnect between BP and CM pins and so, you can program again the keyboard, starting on first step. 3

4 ELECTRIC CONNECTIONS KEYBOARD Réf : CTL 18 (3 relays 12V) Relays outputs C3 R3 T3 C2 R2 T2 C1 R1 T1 LED3 LED2 LED1 CTL 18 Power supply Keyboard (0v / 12v ) (LM BZ GD IN) activating the relay during 3 seconds US connected: factory configuration HR : Clock switch US non connected : Installant configuration RED GREEN SHIELD YELLOW Clock switch Contac POWER SUPPLY 12V DC US connected : - factory configuration US non connected : - fitter configuration A B External Button activating the n 1 relay during 3 seconds TERMINAL BLOCK 12V : 12V DC input C1-R1-T1 : Relay 1 0V : 0V input C2-R2-T2 : Relay 2 US : Factory/fitter codes switching C3-R3-T3: Relay 3 LM : Activated keypad red Led BZ : Activated buzzer and green led GD/ IN : Push button keyboard decoding HR/ CM : Clock inputs BP/CM: activation of the n 1 relay 4

5 CLAV 200 CODIFICATION NOTICE MASTER CODE : address number 48 TEMPORISATIONS address Address address number 50 number 51 number 52 Relay 1 tempo Relay 2 tempo Relay 3 tempo DIGIT NUMBER BY CODE : address number 49 KEYPAD CODES Permanents codes for n 1 relay Permanents codes for n 2 relay Permanents codes for n 3 relay Permanents codes activating simultaneously the n 1 & n 2 relay Permanents codes activating simultaneously the n 2 & n 3 relay Permanents codes activating simultaneously the n 1,n 2,n 3 relay Closks code : (the clock swich has to be closed) TOUCH «0» : adress n 54 yes / no 5