EMB-CPU04. User s Manual

Transcription

1 EMB-CPU04 User s Manual Windows, Windows2000, Windows NT and Windows XP are trademarks of Microsoft. We acknowledge that the trademarks or service names of all other organizations mentioned in this document as their own property. Information furnished by DAQ system is believed to be accurate and reliable. However, no responsibility is assumed by DAQ system for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or copyrights of DAQ system. The information in this document is subject to change without notice and no part of this document may be copied or reproduced without the prior written consent. Copyrights 2009 DAQ system, All rights reserved

2 Contents 1. Introduction 1.1 Features 1.2 Application 1.3 Specification 2. Appearance 3. Driver Installation 3.1 Sound Driver 3.2 LAN Driver 3.3 Touch driver 3.4 Graphic Driver 4. Set Display -2-

3 1. Introduction The EMB-CPU04 is the low cost Single Board Computer(SBC) which equipped a low power and low heat processor of the Intel Atom Z520PT. It provides solution to be suitable for Embeded market wanting low power and small size. Application Factory Automation Data acquisition Medical and Robotics Auto PC UMPC(Ultra Mobile PC) Instrument control PC 1.1 Features - Intel Atom Processor Z520PT(Z510PT, Z530P) - Intel system controller hub US15WPT chipset - Intel GMA500 graphics driver (VGA, LVDS) - Single Power( +9V to +15V) operation - Compact small size 160 x 100mm - Supports industrial Temperature range ( ) - Operating Systems : Windows XP 1.2 Application - Factory Automation - Data acquisition - Medical and Robotics - Auto PC - UMPC(Ultra Mobile PC) - Instrument control PC -3-

4 1.3 Specifications Form Factor Processor System Chipset Bios Memory 160 x 100mm Intel Atom Z520PT(512K cache, 1.33GHz, 533MHz FSB) Intel System Controller Hub US15WPT AMI bios 1 x 200 pin DDR2-400/533 SODIMM max up to 2GB Extension Slot Compact Flash slots 44pin IDE to Compact Flash type-2 adaptor PC card slots NVRAMs Display Ethernet EIDE Audio Serial I/O Support LVDS, VGA Dual Display one 10/100/1000 Mbps Ethernet port 2mm pitch 44pin EIDE connector HD Codec audio with mono speaker AMP Two serial ports, one can be used as touch input Parallel Port USB Four USB A connector, Two with 10pin header Watch dog timer Status LEDS Indication for Ready and operation Power Input Single +9 to + 15V range power max current is 1.5A Debug Connector Operating Temperature Rating Power Consumption -40 to 50(without FAN and Heat-sink), -40 to +85 (with Heat-sink) Max 15W Regulator compliance -4-

5 2. Appearance POWER S/W SO-DIMMDDAR2 MEMORY Intel US15WPTSCH Intel Atom PIC Express Slot COM1 (J17) Main Power Switch of EMB-CPU04 256M ~ 2GB memory System Controller Hub Chipset(CPU, Video, Memory, USB, Network, HDD, Express PCI) Processor PIC Express slot PIN Connecter for serial connector -5-

6 1. PIN : RX1 2. PIN : TX1 3. PIN : Touch screen 4. PIN : Touch screen 5. PIN : GND Speaker SPK connecter MIC MIC connecter Line AUX connecter USB 1~4 USB connecter DC power Input Single +9 to + 15V range power max current is 1.5A IDE 2.0mm 44 PIN Flash memory connecter Two USB 10pin Header (J10) Ethernet 1.PIN, 2.PIN : +5 V 3.PIN : 1D- 4.PIN : 2D- 5.PIN : 1D+ 6.PIN : 2D+ 7.PIN, 8.PIN : GND 9.PIN,10.PIN : No Connect one 10/100/1000 Mbps Ethernet port -6-

7 3. Driver Installation 3.1 Sound Driver - Execute the file in CDROM:\Driver\audio\audio_WDM_R241\setup.exe. 3.2 LAN Driver - Execute the file in CDROM:\Driver\Lan\AsusSetup.exe

8 3.3 Touch Driver - After execute the Setup file in Touch folder in CD-ROM, display the icon of TouchWare at the wallpaper. - Double click the TouchWare. - Click the HW Info. - Click the Auto Search Touch button, check the connection port. - After finding the port at Touch Controller, press OK. - Choose the Calibrate button

9 - When show the below display, press the lighting point. (You should continuously press until completed progress bar.) - Press Yes, and then finished the install. 3.4 Graphic Driver CDROM:\Driver \Driver\Graphic\XP\setup.exe 를실행하여 Graphic Driver 를설치합니다

10 4. Set Display Installation when including LCD Setup Display After click the right mouse at the display properties, and choose the Graphic Property. MID Monitor Single Output - It is possible with single display setting if connected to MID Monitor only. (Single Display Output at MID Monitor)

11 MID Monitor AND DeskTop Monitor Single Output - MID Monitor and DeskTop Monitor (VGA Connecter) are all Graphic Properties setting screens in connection state. - It can be displayed to choose one of the two (MID Monitor or Desk Top Monitor) in case of Single Display setting. (MID Monitor or Desk Top Monitor Single Output)

12 MID Monitor AND Desk Top Monitor Multiple Output - When Intel(R) Dual Display Clone is set in Multiple Display, it is possible to display same display output at MID Monitor and DeskTop Monitor. (Same Display Output) - It can be use the expansion monitor to make a monitor between the MID Monitor and Desk Top Monitor, in case of setting Expansion Desk Top. (Expansion Monitor Output)

13 Only DeskTop Monitor Installation when not including LCD When Installation Graphic Driver and re-booting, windows logo display shows at DeskTop Monitor as like below picture. After logo display disappear, do not show nothing at DeskTop Monitor because a graphic driver outputs a display at initial setup LCD. At this time, press [Ctrl] + [Art] + [F1] one minute later, a display outputs at Monitor. This setup needs a setting of once when install window