DI-10. When Accuracy Counts

Transcription

1 DI-1 Check Wei ghi ng Scal e When Accuracy Counts Service Manual 73355

2 1 CONTETS PAGE a. EXTERNAL VIEW DISPLAY & KEYS Display Sign lamps Keys SET UP SPECIFICATIONS FEATURES OPERATION INSTRUCTION Power ON. -_ One touch tare Digital tare Digital tare during weighing _ Set point setting _ Addition and subtraction. _ Counting. --_---_ NET/GROSS display Data ti Time setting lO.LB/KG conversion CALIBRATION SPEC. LIST ERROR MESSAGE LIST

3 2 1. EXTERNAL VIEW 2.DISPLAY 2;1*Display & KEYS. Dl,-1 W=24 D=26 H = 92 (mm) * Weight value is displayed loaded on the scale. * Weighing unit, sign lamps and filling graphic for set pint are displayed.

4 3 2-2.sign,,.~~,, lamps [-o-j Zero lamp : ON, when display is true zero. m Tare lamp : ON, when tare is subtracted. [r] Net lamp : ON, when net weight is displayed. c3i3 Gross lamp : ON, when gross weight is displayed. m BATT. lamp : ON, when battery run out. [r) W.S lamp : ON, when weight is in stable condition. I] HI lamp (1 OK lamp ( LO lamp : ON, when weight value reached to "HI" set point programmed. : ON, when weight value reached to "OK" set point programmed. : ON, when weight value reached to "LO" set point programmed.

5 2-3.Keys * - Total key : Use for total weight call and print out. Use for weight data print out without addition. Plus key : Use for weight data addition and print out. Minus key : Use for weight data subtraction and print out. a- - 9 Numeric : Use for data entry. key ON/OFF key : Display ON/OFF key.(not for main power.) Mode key : Weighing conversion key. NET/GROSS : Display change for NET and GROSS. key Feed key : Paper feed key.(in case of PRINTER connection). : =: Set point : Set point programming for "HI'~,"OK" and key "LO". Sample key : Use for number of sample entry on counting mode Tare key : Use for tare reduction. Re-zero key : Weight display re-zeroing. CL Clear key : Use for data clear. # Code key : Use for programmed code number read out.

6 5 3.SET UP l-put display side on the soft cloth or similar. 2.Remove rear lid and brackets by 6 screws. 3.Fix the cable to connector A. 4.Re- mount the rear lid and brackects.

7 l.remove the right side cover. 2.Remove the dry cell box. 3.Put the dry cell in the box. ( 6 pcs.) (Please pay attention to the polarity of the dry Cells) 4.Re-mount the dry cell box. 6

8 4. SPECIFICATION MODEL,SPEC,, * Power source : D.C 12V.5A (AC/DC adaptor) D.C 1.5V x 6 pcs. (Dry battery) * Operating temperature : o*c * Operating humidity % RH. * Power consumption 1 w/h. ANALOG SPEC: * Input sensitivity :.5mV/V to 4mV/V * Zero adj. range : -6 mv... 3 mv. * L/C applied voltage : DC 12.V. * Temp. characteristic : ZERO...+(.2uV + 8ppm of ZERO)/"C SPAN _..+ 8 ppm/"c * Speed of A/D conversion: 8 or 16 times/set. (selectable) * Non linearity :.1 8 DISPLAY_SPEC;: * Weight display * Tare * Set point 1 (LO) * Set point 2, (OK) * Set point 3 (HI) * Display total. * Weighing unit * Sign lamps * Filling graphic : 6 digits. : 6 digits. : 6 digits. : 6 digits. : 6 digits. : 6 digits. : 4 kinds "g","kg","lbs","oz" & "dwt" : 9 kinds "ZERO","TARE","NET","GROSS" "BATT" "was", UHI", WOK", "Lo" : 2 kinds rough and fine. * Printer * Print method * Items to be print * Paper * Print color : Model 15 II 16 digits/line. 5 x 7 dots/chars. : Dot impact printer Ink ribbon cartridge. : Date(MM.DD.YY.)... 2 digits each. : Time(HH.MM) digits each. : Code No digits. : Weight digits. : Total weight digits. : No. of transaction... 4 digits. : Signs "+".... Addition?'-'I.... Subtraction. (1*?I.... Non addition. "T".... Total. "kg".... kg mode. lb.... lb mode. : Normal paper is used. : Black or purple.

9 t 56.8 kg ks lbb.ro I:9 5. FJZATURES _ *, LCD graphic display is used for filling in indicator. * Battery drive available. (about 1 to 2 hours) * Up to 4 x 35o load cell can be drive in case AC/DC adaptor is used. ( in the case of battery drive, only one 35n load cell can be drive.) * 5 kinds of weighing mode kg,g,lbs,oz and dwt. * One touch tare, Digital tare, Digital tare during weighing. * Addition & subtraction.? NET/GROSS conversion. * Automatic zero tracking. * Automatic print. * Automatic * Automatic calibration. power off. * Data out put by RS-232C for external device. (Option) * Set point data out put. (Option) * Built in printer. (Option) * Code No. printing. * Da-te & time printing. * Counting function. * Programmable scale capacity and scale * Meets or exceeds the requirements of interval. OIML class 3 in case of l/3 display resolution.

10 9 6 OPERATION INSTRUCTION * P 1.3 is program version number. ZERO : Zero lamp W.S: Weight stable TARE : Tare lamp HI : "HI" set point NET : Net lamp OK : "OK" set point GROSS: Gross lamp LO : "LO" set point BATT.: Kg mode l-set dry cell or AC/DC adaptor,, I, II then depress Ea key. II P II I, II * DiSDlaY scrolls to II then all the sign lamps, weight unit and filling in graphic are displayed for checking purpose. * If you want to stop the ~

11 1 2.Ready to weigh. * After this page, all the mxa descriptions are written based on 6.kg/O.O2kg scale. u I - m.. I (When unknown tare weight) l-place tare weight. *Ready to weigh. 3.Place weight. (Ex kg)

12 4.Remove tare & weight 5.Depress *T key. I I I O.! *Tare weight is cleared. *Ready for next OperatiOn. mm u l.enter tare value by numeric key. (Ex kg) (When known tare weight) 2.Depress *T 3 key. I4 II 1 II mn 3.Place tare weight 2.34 kg. I *Ready to weigh.

13 12 4.Place weight. (Ex kg) 5.Remove tare & weight. ii - 1': oa; b-depress +q 3 key. *Tare is cleared. l-place tare & weight. tare : 1. kg weight: 4.56 kg total : 5.56 kg 5'1.5 u 6m' 2.Enter tare value by numeric key.

14 3. Depress +T 3 key. 4.Remove tare & weight. 5. Depress *T 3 key. *Tare is cleared. l-depress (5) key. II I, II II 6. 1 *Scale capacity(6.kg) is set automatically for "LO", "OK" & "HI" when no data. *See "NOTE" for the detail. m! II 1. l (Ex. set set point point "LO"=lO.OO "OK"=2. kg) kg ~ set point "HI"=3. kg 2.Enter set point for "LO". II II Enter J

15 3.Depress fsj key. Enter set point for "OK". Enter 4.Depress f9 key. Enter set point for "HI". Enter 5.Depress fs> key. *Completed & ready to weigh. NOTE : * The filling graphic will be as follows when same value are set to each set point. Ex.) 6. kg/o.2 kg. Set point "L"="K"="H1"=6. kg kg kg 6. kg kg s = kg 4 step * The filling graphic will be as follows when different value are set to each set point. Ex.) 6. kg/o.2 kg. Set point "LO"=lO.OO kg,"ok"=2. kg,"hi"=3. kg.2 to 1. kg _ lo. kg _ kg kg _ kg

16 1.2 to 2. kq ' I I- I- I- -ci 2.2 to 3. kg I 3.2 to CAPACITY l-enter Code No. by numeric key.,, I, 11 II Ex. Code I! 2.Depress # key. II I, Ii II. OmII I

17 3.Place weight then depress key. Ex. 1. kg II 1. Olall II *Total weight appears and display flashes 4 times. 4.Remove 1. kg and place II II II another weight then depress , Orall + key. Ex. 15. kg *Total weight appears and display flashes 4 times. u J - 5.Depress - w key for II I, II correction.l[ 1. omjl (subtraction) 6.Remove weight, enter weight II value if it is known weight. I/ II I II (fjg4~@@ 7.Depress a key for addition,, II II L.2 II m11 then depress * key to cal up total weight. 8.Depress * key again to print out total weight. II II II II. OBll

18 .L, l.place samples 1 PCS., then II I, II m II 1 II depress w key. II EX. 1 PCS. sample =.1 kg *If the sample weight is less than.1% of scale capacity, m will be displayed. Please place q more samples, /-L-Y then depress (-<:;*) key again. 6.kg x.1% =.6 kg (6Og) 2.Place items to be count. 1 I I EX. 5 PCS. II m 5 'lo; 3.Remove items and depress 'cq key to release counting mode. l-subtract tare and place weight,, Ex. tare = 1. kg weight =lo.oo kg n II Z.Depress key to indicate b " ll Gross weight. n 1 1. Olall w5ea A,mim u LI

19 cl 18 b 1 3.Depress +I key to indicate/l 1. Orall NET weight. u I l.depress at the same time. -II II 2.Enter date by numeric key II,Ex. 14.Nov II * Enter data in order of YY.MM.DD. I( * Display flashes for confirmation. 3.Depress EEI time by numeric key. Ex. 12:34 key then enter 1, 1 II l L2IKzl , * 24 hours. * Display flashes for confirmation. 4.Depress izl key.

20 l.place 1. kg weigh.t. 2.Depress,$JL key. 3.Depress key. II I, II II 1. Omn LJ NOTE : Weighing Weighing conversion conversion "lb" '*g" to "kg" or to "oz","dwt" "kg" or to "lb" are available. vise versa are available. I

21 2 7.CALIBRATION. l.depress 8715 while keep II II II depressing * Select appropriate weighing IIU n 1 La 1 ii I Ex. 2.Depress kg. key. 3.Enter scale interval (minimum 1, graduation) by numeric key. 1) II II. -'2 I\ II Ex..2 4.Depress # key. Ii II 1 II c A p n 5.Enter scale capacity by II,I il numeric key. II 6. n

22 6.Depress # key. CAL is II " II - II C A L II displayed, depress key. " * Please make sure that nothing has been placed on the scale. L 21 7.CAL SP is displayed. Place the& weight and enter the value of 11 C A L ~ S P i the weight. If it is capacity weight, simply depress # key. * We recommend to use capacity weight for the calibration to have correct scale accuracy. S.Completed. c The scale capacity must be set within the following range. Scale capacity = 1 or less. Min. graduation (scale interval) t For example, if the min. increment is "2", you can set the scale capacity up to the "2". But the higher display in-correct resolution weight may result display in flickering some case. display or c If you don't have the capacity weight for calibration, you can use any known weight in stead of capacity weight. (see item,7) - The minimum graduation must be following value.

23 22 8. SPEC LIST l-there are 2 ways to access the specification changeover. * keep key. This is a specification changeover access code which are related with user's changeable function. Spec. to 9 are available. * Depress while keep depressing -) ' This is a specification changeover access code which are related with the W & M regulation for each country. Spec.1 to 19 are available. 2.All the specification data consists of 4 digits binary code and some of them are available in combination with another spec. data in some case. 3.When above code is accessed, display shows spec No. (2 digits) and it's data (4 digits) reciprocally as shown below which are set at the factory when shipping. Spec. No. Data of Spec. 4.Data construction and usable keys. SPEC. --- X X & & 5.Useable keys. Bit Bit 1 Bit 2 Sit --- Data entry.( are available ) Skip Spec. No. & data set Skip back Spec. No. & data set # Program end. 6.The spec. data marked below Spec. No. are standard spec. data when shipped. "Not used" should be set to "" always.

24 23 ;PEC. No. Bit 3 Bit 2 Bit 1 Bit ;PEC. Set point func- Nega. weighing. Printer connec- -tion. -tion. : Yes : Yes : No ooao 1 : No 1 : No 1 : Yes ;PEC. Manual weight Time print. Data out put. Serial I/F. 1 entry. : No : Continuous : No 'ol,lo y i ;y 1 : Yes 1 : by key in 1 : Yes ;PEC. Weighing unit Automatic print 2 Not used Not used change. : Yes : No '~ 1 : No 1 : Yes ipec. Not used Not used Not used Not used Not used Date order : YY.MM.DD YY --- Year : DD.MM.YY MM --- Month 1 : 4 min. 1 : 8 min. 11 : 12 min. 1 : 1 min : 5 min. : 6 min. 11 : 9 min. 111 : 13 min.

25 ;PEC. No. Bit 3 Bit 2 Bit 1 Bit ;PEC. 1 Not used Not used Not used Not used 1; ;PEC. Tare during Re-zero during Scale start Weighing unit 13 zero tracking. zero tracking. range. (display/print : Yes : Yes : k 6IR. :Yes Y : No 1 : NO 1 : t 3 IR. 1 : No ;PEC. Manual tare Tare decrease. Tare stack up. Tare limit. 14 clear. : Yes : Yes : Yes : 5 % of 1 : No 1 : No 1 : No 1: 5 8 of FS, ;PEC. Scale start When Net weight When Gross wei- Zero lamp rangt 15 range 2 IR. is below -ght is below : No : Minus sign : Minus sign :Gross %1/4( OOCJO 1 : Yes 1 : Blank 1 : Blank 1 :Net 2 i/4( ;PEC. Auto Tare Clear A.T.C condition Digital tare. Print limit. 16 : No : Net 21 d. : Yes : Below d ~OQQCJ : Yes :Net ld. :No : Below 2 d ;PEC. Decimal point. Net 2 d + 5 d Negative total. Double print. 17 cgc$ Y : Comma : Period : No. 1 : Yes : Yes 1 : No : Yes 1 : No ;PEC. Tare exchange. 18 ~~ Not used Not used Not used : Yes 1 : No ;PEC. Sensitivity of the Load cell to be used. 19 : mv/v 1 : mv/v 1 : " 11 : (I 1 :, n 11 : w 11 : " 111 : w 1 : " 11 : w 11 : ' 111 : : ' 111 : w ::loal 111 : " 1111 : " Note: IR. = Internal count. FS. = Full scale

26 25 9. ERROR MESSAGE LIST Following error message will be appeared when in-correct operation. is taken. (I Add O Fll When accumulated weight total exceeded 6 digits. When quantity displayed exceeded 6 digits. OF When displayed weight exceeded scale capacity. When weight value entered during calibration operation, is not correct. II II When zero calibration is not correct during calibration operation. Please try zero calibration operation. Same as above. Please try Zero and Span calibration. II Add x XII When sample weight was less than insufficient range. Please place XX PCS. When wrong set point value was entered. (lspt==tq When total weight is minus.

27 NOTICE To enter either the calibration or specification setting, the following procedure must be performed. 1. Remove the two screws and back panel (see illustration). 2. Locate the calibration switch, and move it to the left (as shown). TOP Calibrate/Operate Switch DI-1 Rear view, back panel off. 3. Perform the calibration or specification code setting as needed. 4. Be sore to move the switch to the right before placing the unit back in service, to prevent unauthorized access. 5. Replace seal(s).

28 DIG1 GRAND STANDARD SPECIBICATIONS REZERa,9PEC NO. STD.SETTING OS REZERO l-4-2 SPEC NO STD.SETTING

29 DI-1 Limited Warranty Rice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by a Distributor or Original Equipment Manufacturer (OEM) will operate per written specifications as confirmed by the Distributor/OEM and accepted by RLWS. All systems and components are warranted against defects in materials and workmanship for one (1) year. RLWS warrants that the equipment sold hereunder will conform to the current written specifications authorized by RLWS. RLWS warrants the equipment against faulty workmanship and defective materials. If any equipment fails to conform to these warranties, RLWS will, at its option, repair or replace such goods returned within the warranty period subject to the following conditions: Upon discovery by Buyer of such nonconformity, RLWS will be given prompt written notice with a detailed explanation of the alleged deficiencies. Individual electronic components returned to RLWS for warranty purposes must be packaged to prevent electrostatic discharge (ESD) damage in shipment. Packaging requirements are listed in a publication, Protecting Your Components From Static Damage in Shipment, available from RLWS Equipment Return Department. Examination of such equipment by RLWS confirms that the nonconformity actually exists, and was not caused by accident, misuse, neglect, alteration, improper installation, improper repair or improper testing; RLWS shall be the sole judge of all alleged non-conformities. Such equipment has not been modified, altered, or changed by any person other than RLWS or its duly authorized repair agents. RLWS will have a reasonable time to repair or replace the defective equipment. Buyer is responsible for shipping charges both ways. In no event will RLWS be responsible for travel time or on-location repairs, including assembly or disassembly of equipment, nor will RLWS be liable for the cost of any repairs made by others. THESE WARRANTIES EXCLUDE ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NEITHER RLWS NOR DISTRIBUTOR WILL, IN ANY EVENT, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. RLWS AND BUYER AGREE THAT RLWS S SOLE AND EXCLUSIVE LIABILITY HEREUNDER IS LIMITED TO REPAIR OR REPLACEMENT OF SUCH GOODS. IN ACCEPTING THIS WARRANTY, THE BUYER WAIVES ANY AND ALL OTHER CLAIMS TO WARRANTY. SHOULD THE SELLER BE OTHER THAN RLWS, THE BUYER AGREES TO LOOK ONLY TO THE SELLER FOR WARRANTY CLAIMS. No terms, conditions, understanding, or agreements purporting to modify the terms of this warranty shall have any legal effect unless made in writing and signed by a corporate officer of RLWS and the Buyer. 22 Rice Lake Weighing Systems, Inc. Rice Lake, WI USA. All Rights Reserved. RICE LAKE WEIGHING SYSTEMS 23 WEST COLEMAN STREET RICE LAKE, WISCONSIN USA