My Home AUTOMATION GUIDE

Transcription

1 My Home AUTOMATION GUIDE

2 CONFIGURATION Touch control item HC/HS4657M3 and item HC/HS4657M4 The Nighter & Whice control is an SCS control where the traditional pushbuttons are replaced by capacitive sensors. Touching the area of a sensor with a finger is the same as pressing a pushbutton. The device can thus perform some functions typical of an SCS control by simply touching its surface. It is available in flush-mounted versions with 3 and 4 modules, with 6 and 8 keys respectively. Each zone corresponding to a key is marked in the centre by a light blue LED. When the user s finger comes close the intensity increases appreciably and remains intense until the finger is removed. This effect gives the user the feeling that he has activated the command. Use the configurator to change the levels of intensity. Modes of operation The Nighter & Whice control can work in four different ways: self-learning, scenarios, swing, CEN. - The self-learning mode (cyclical or non-cyclical) lets you associate most of the typical commands of the automation, sound and video door entry systems, as well as the auxiliary commands, to each key. - The scenario mode lets you call, program and cancel 6 or 8 scenarios of a scenario module. - The switch mode lets you drive 3 or 4 consecutive light points or rolling shutters (or rooms or groups). - The CEN mode lets you send commands to the scenario programmer (MH200). front view Technical features The Nighter & Whice SCS control has the following features: 1) removable terminal for connection to the BUS 2) housing for four configurators: A, PL, M, INT programming pushbutton P HC/HS4657M3 configurator housing BUS A PL M INT room light point mode LED intensity rear view Max Absorption HC/HS4657M3 30mA HC/HS4657M4 40mA MY HOME - AUTOMATION

3 Configuration The Nighter & Whice can be configured in two different ways: - Physical configuration: putting the physical configurators into their housings. - Virtual configuration: the control can be configured remotely, whenever you do not have the physical configurators. (For details, refer to the Virtual Configuration guide). Apart from modality, the control always needs an univocal A/PL address in the system programming pushbutton Use only the screwdriver (T2738A) supplied The functions which can be obtained are listed below. Self-learning mode M=0 This mode of operation lets you associate a single command to any device key. Each command can be created, cancelled or modified. Program the keys Follow the following procedure to associate a different command to any of the keys: 1) keep the pushbutton on the back pressed for 3 seconds; the LEDs light up. Release the pushbutton, the LEDs light up in rotation; 2) touch the key that you want to program within 20 seconds: the LED starts to flash, indicating that the programming mode has been activated; 3) set the command which you want to associate with the key, acting on the command or the corresponding actuator. The LEDs start to turn again; 4) at this point you can repeat points 2 and 3 for all the keys, also for a key for which the association has been made if you want to change it; 5) press the pushbutton quickly or wait 20 seconds to quit the programming. Cancel the key programming 1) keep the pushbutton on the back pressed for 8 seconds; first the LEDs light up then they return to the minimum level set. Release the key within 4 seconds, the LEDs shine simultaneously; 2) press the key that you want to cancel within 20 seconds: the cancelled key will no longer activate a command until it has been reprogrammed; 3) the corresponding LED flashes 4 seconds, alternately with the others. After this you can repeat point 2 to cancel other programmings;; 4) press the pushbutton quickly or wait 20 seconds to quit the programming. NOTE: To cancel the programming of all the keys at the same time, keep the pushbutton on the back pressed for 12 seconds; first the LEDs light up, then they return to the minimum level set and then they switch ON again. Release the key, the LEDs flash in sequence for about 4 seconds, confirming that all the programming has been cancelled. CONFIGURATION My Home AUTOMATION GUIDE

4 Non-cyclical self-learning mode M = 6 This mode is a variation of the self-learning mode (M=0) in which the keys never work cyclically. Thus if, for example, the ON of an actuator or dimmer has been learnt, the pair of keys configure automatically to switch ON or increase the intensity level for the upper key and switch OFF or decrease the intensity level for the lower key. If instead a single function (e.g. calling a scenario) has been learnt, the other key of the pair remains without a function or keeps the function it had previously. Scenario mode M=1 4 This mode of operation is only used if the system has a scenario module item F420. The user can create, cancel or modify the scenarios in the scenario module and can use the keys to call them. The procedure can save up to 16 scenarios using two 8-key devices, or three 6-key devices. The following table shows the correspondence between the scenario number saved in the scenario module and the control key in the possible configurations: 3-module control (6 sensors) Key number M=1 M=4 M=3 Key 1 Scenario 1 Scenario 7 Scenario 13 Key 2 Scenario 2 Scenario 8 Scenario 14 Key 3 Scenario 3 Scenario 9 Scenario 15 Key 4 Scenario 4 Scenario 10 Scenario 16 Key 5 Scenario 5 Scenario 11 - Key 6 Scenario 6 Scenario 12-4-module control (8 sensors) Key number M=1 M=2 Key 1 Scenario 1 Scenario 9 Key 2 Scenario 2 Scenario 10 Key 3 Scenario 3 Scenario 11 Key 4 Scenario 4 Scenario 12 Key 5 Scenario 5 Scenario 13 Key 6 Scenario 6 Scenario 14 Key 7 Scenario 7 Scenario 15 Key 8 Scenario 8 Scenario 16 Program a scenario 1) enable the programming of Module item F420 so that the programming state LED is green (press the lock/unlock key on the Scenario module for at least 0.5 seconds); 2) keep the pushbutton on the back of the Nighter and Whice control pressed for 3 seconds; the LEDs light up. Release the pushbutton, the LEDs light up in rotation; 3) press the key corresponding to the scenario to be programmed. The LED Programming starts to flash (when it receives the updating of the scenario module) lock/unlock key indicating that the programming mode has been activated; 4) set the scenario, by means of the commands and/or the corresponding Programming actuators; state LED 5) press the key to quit the programming: the LEDs start to flash in rotation again. At this point you can repeat points 2, 3 and 4 for all the scenarios, also for a key for which the association has been made if you want to change it; 6) press the pushbutton quickly or wait 20 seconds to quit the programming. Item F420 Scenario cancellation key Scenario/learning reset LED MY HOME - AUTOMATION

5 Cancel a scenario 1) scenario module item F420 must be in configuration with self-learning enabled; 2) keep the pushbutton on the back of the Nighter and Whice control pressed for 8 seconds; first the LEDs light up then they return to the minimum level set. Release the key within 4 seconds, the LEDs shine simultaneously: 3) press the key corresponding to the scenario that you want to cancel within 20 seconds; 4) the corresponding LED flashes 4 seconds, alternately with the others. After this you can repeat point 2 to cancel other programmings; 5) press the pushbutton quickly or wait 20 seconds to quit the programming. NOTE: operate the scenario module to reset the entire memory. Keep the reset (DEL) key pressed for 10 seconds after pressing the self-learning key so that the LED is green. Swing mode: M=O/I; hi; him This mode allows rapid installation without need for learning or scenario modules, driving 4 or 3 consecutive light points or rolling shutters. The A PL address is the light point or rolling shutter commanded by the first pair of keys, the next pairs command the next light points or rolling shutters. If the Amb or Gr configurator is inserted in A, in the same mode the 4 or 3 pairs of keys command consecutive rooms or groups starting from the one indicated by the configurator in PL. ON/OFF command ON command with upper key, OFF with lower key. For point-point commands the key performs the On/Off function with short press, the adjustment with long press; for the other commands it only performs On/Off. O/I configurator Command (UP-DOWN for rolling shutters) M= hi (Up/Down): up and down command until end of travel (rolling shutters) hi configurator Monostable command (UP-DOWN for rolling shutters) M= him (Up/Down monostable): up and down command for the time the key is pressed him configurator Mode for scenario programmer, M=CEN A scenario configured in the MH200 scenario programmer is associated with the activation keys of the Nighter and Whice control when programming the scenario with the TiMH200 software. Configuration A = 0, PL = 0 is not acceptable. This mode of operation is only used if the system has a scenario programmer (MH200). CEN configurator CONFIGURATION My Home AUTOMATION GUIDE

6 Selection of the LED intensity (INT configurator) The INT configurator can be used to select between different LED lighting intensities, depending on the installation needs. You can set the LED intensity to fade when it is being switched OFF or switch it OFF suddenly - INT=none at rest the LED are lit up at 30%, if a key is pressed the corresponding LED lights up at 75%. - INT=1 at rest the LED are lit up at 45%, if a key is pressed the corresponding LED lights up at the maximum level (about 90%). - INT=OFF at rest the LED are OFF, if a key is pressed the corresponding LED lights up at 45%. - INT=2,3,4 same brightness as before but without fading on switching OFF INT Configurator Level at rest Level with key pressed 0,2 30% 75% 1,3 45% 95% OFF, 4 Off 45% When the device has been installed wait two minutes for it to finish the auto-calibration. During this time commands can be sent automatically to the system. MY HOME - AUTOMATION