Drive Software Wizards v3.2

Transcription

1 Release Notes Drive Software Wizards v3.2 This release notes describes major revision 3, minor revision 2 of drive software wizards for DriveExplorer (v5.02 and higher), DriveTools SP (v4.01 and higher) and RSLogix 5000 Drive Add-On Profiles (v1.00 and higher). The following information is included in this document: Topic Page Available Wizards for Each Release Below Determining the Wizard Revision Level 2 Installing the New Revision 3 Verifying the Wizard Revision 3 Enhancements 3 Corrected Anomalies 4 Restrictions 5 Available Wizards for Each Release Each new wizard release contains all of the previous released wizards, plus any new wizards: Release Wizard v1.2 v1.3 v2.1 v2.2 v2.3 v2.4 v2.5 v3.1 / v3.2 PF70 Startup PF70EC Startup PF700 Startup PF700VC Startup PF700S 2 Startup PF40/40P Velocity StepLogic DPI Tech Support DSI Tech Support SCANport Tech Support PF700H Startup PF40P Positioning StepLogic PF DC Startup PF4M Startup PF4 Startup PF40 Startup PF40P Startup PF400 Startup PF700VC Profiling

2 2 Release v3.1 / Wizard v1.2 v1.3 v2.1 v2.2 v2.3 v2.4 v2.5 v3.2 PF755 Startup (1) PF755 Safe Speed Monitor (1) MSR57 Safety Relay Startup (1) Data Logging PF753 Startup (1) PF755 Homing (1) PF755 Profiling (1) PF755 PCAM (1) PF755 HiP Startup (1) PF755 Trending (1) (1) Only compatible with DriveTools v5.01, DriveExplorer v6.01, and Drives AOP v2.01 or higher. Determining the Wizard Revision Level This section describes the procedures to determine the revision of your drive software wizards. Run DriveExplorer, DriveExecutive or RSLogix 5000 Drive Add-On Profiles and connect to a drive online, or run DriveExecutive or RSLogix 5000 Drive Add-On Profiles and open a saved drive configuration offline. Launch any available wizard and view the revision on the start-up window.

3 3 Installing the New Revision This section describes the procedure for installing the drive software wizards. 1. Run the v3.2 installation file. 2. Verify the wizard revision (see section below). Verifying the Wizard Revision Run DriveExplorer, DriveExecutive or RSLogix 5000 Drive Add-On Profiles and connect to a drive online, or run DriveExecutive or RSLogix 5000 Drive Add-On Profiles and open a saved drive configuration offline. Launch any available wizard and view the revision on the start-up window. It should be v3.2.xx (ignore the right-most digits). Enhancements There are no enhancements provided in this version of software.

4 4 Corrected Anomalies The following anomaly corrections were made in this version of drive software wizards: PowerFlex 755 Profile Setup Wizard Anomaly: The PowerFlex 755 Profile Wizard's Cam Definition can display the velocity as the incorrect type of curve for some segments. Correction: The Cam Definition now shows the correct type. PowerFlex 755 Wizards Indirect Values Error Anomaly: PowerFlex 755 Wizards would not allow finishing the wizard and would show some indirect values as invalid values with some non-english drives. Correction: The PowerFlex 755 wizard's parameter indirect selector now correctly operates for parameters with a - contained in the name and allows the wizard to finish and correctly display the values. PowerFlex 700VC Startup Wizard in RSLogix 5000 Anomaly: When creating a new PowerFlex 700VC in RSLogix 5000 (inside Drive Add-On Profiles), launching the PowerFlex 700VC Startup Wizard would cause RSLogix 5000 to stop functioning. Correction: PowerFlex 700VC Startup Wizard now works with Drive Add-On Profile in RSLogix PowerFlex 700VC Startup Wizard Anomaly: The PowerFlex 700VC Startup Wizard could cause an overcurrent fault in the drive if the direction parameter was changed on the direction test page while it was running. Correction: This was fixed by forcing the drive to stop before it can change the parameter for direction. PowerFlex 700H Startup Wizard Anomaly: The Speed Control page shows some of the terminal numbers of the PowerFlex 700VC instead of the terminal numbers of the PowerFlex 700H. Correction: The terminal numbers were corrected on the graphic.

5 5 Restrictions The following restrictions apply to this version of drive software wizards: Drive software wizards (v1.2) were introduced with the launches of DriveExplorer v5.01 and DriveTools SP v4.01. Earlier versions of these software tools do not support wizards. Although wizards were introduced with DriveExplorer v5.01, DriveExplorer v5.02 (or higher) is required to use the v1.3 and some higher wizards. Some wizards are only compatible with DriveTools 5.01, DriveExplorer 6.01, and Drives AOP 2.01 or higher. Please refer to the Available Wizards for Each Release table on page 2. Restrictions are noted in footnote 1.

6 Rockwell Automation Support Rockwell Automation provides technical information on the web to assist you in using our products. At you can find technical manuals, a knowledge base of Frequently Asked Questions (FAQs), technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. Rockwell Automation also provides complimentary phone support for drives, communication adapters, and peripherals. If you experience a problem with the software, please review the information in the online Help. For further help in getting your software operational, contact a Customer Support representative: United States Monday Friday, 7am 6pm CST Outside United States Please contact your local Rockwell Automation representative for any technical support issues. For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnect Support programs. For more information, contact your local distributor or Rockwell Automation representative, or visit Allen-Bradley, Rockwell Software, Rockwell Automation, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat: İçerenköy, İstanbul, Tel: +90 (216) Publication 9303-RN018A-EN-P - November 2011 Copyright 2011 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.