UNIVERSAL SOFTWARE. Universal Software. Data Sheet

Transcription

1 Universal Software Data Sheet

2 System Requirements: The minimum requirements for using the Software are: 1). Windows XP/Vista/7 2). A minimum of 512 MB RAM 3). 1 GB of hard disk space 4). Microsoft Office Access 2003 or higher 5). Serial Port - COM Port (minimum 1) 6). USB Port 7). CD-ROM Drive 8). RS-232 to RS-485 Converter 9). Software dongle of data logger (According to software requirement). A free serial port or a USB port must be provided for communicating the PC to the data logger using the communication interface.

3 Software Features:- Universal Software is highly reliable. This software is very user friendly. User defined Channels selection and customized instruments name. Three types of Data Reports can generate 1. Data Report of TEMPERATURE, RH, DP, AIR VELOCITY. 2. Alarm Report. 3. Audit-Trail Report. Direct print of Data Report. View and print Old historical Data Reports. Data Reports facility. Reports Auto facility.

4 Software installed computer. User can monitor instruments and see the data comes from instruments. User can send data to print from here. RS-485 cable to collect data from instruments

5 Universal Software Installation Process Run the software CD supplied by Unitech Instruments. Double click on the set up wizard file setup.exe. Accept the terms and conditions. As shown in below figures:- 1. Starting Installation Process Double click icon to begin installation. The required drivers and Microsoft.NET Framework are automatically installed if they are not detected on your PC. Figure-1 Unitech Instruments GUI Universal Software Setup Wizard

6 Click button to precede installation process. 2. Select installation folder Figure-2 Unitech Instruments GUI Select Installation Folder Wizard 3. Confirm installation

7 Figure-3 Unitech Instruments GUI Confirm Installation Wizard 3. Installing Software Figure-4 Unitech Instruments GUI Installing Universal Software Wizard 3. Installation Complete Figure-3 Unitech Instruments GUI Installation Complete Wizard To start you can click the Universal Software icon on your desktop.

8 Starting Up Instructions for login into the Software. 1. First run the software. 2. Enter user-name and password and then click button for login into the system. To reset password click this button. User have to Reset Password after password Expired.

9 3. If user-name and password are true then user will get logged into the system, otherwise error message will be displayed as shown in below figure 4. Click button to enter right user-name and password. 5. If user clicks the button with or with-out entering the username and password into the login form then system will close.

10 The System Home Screen will be visible as below. To see reading of instruments room-wise click this button. To connect software with instrument s click this button. To disconnect software from instruments click this button. To see trends of instrumen ts click this button. To generate report of instruments click this button. To generate alarm report of instruments click this button. To change system settings click this button. To generate audit-trails report clicks this button. To know about the company click this button. To exit from the system click this button. To log-out from the system click this button.

11 Overview of the Software When the installation is completed the program can be started according to the software name shortcut on the desktop and in the Start menu under Programs. The main screen consists of various parts that will be discussed in the chapter The main screen consists of mainly twelve parts. 1) Rooms 2) Screen 3) Connect 4) Disconnect 5) Trends 6) Report 7) Audit Trails 8) Settings 9) Alarm 10) About Us 11) Exit System 12) Logout System To make connection with software: Click on instruments. button, after that software will display reading of the To disconnect software: Click on button, after disconnecting software from instruments, software will not show reading of the instruments.

12 When user clicks on figure below: button, form will be display as shown in

13 1) To change parameter name, unit and to set points (For TEMPERATURE, RH and DP) To change parametername clicks this label. To change unit-name clicks this label. To set set-points clicks this button. When user clicks figure below: label, set-name form will display as shown in Write the new name here and clicks button to apply change or Clicks button to discard change.

14 When user clicks below: label, unit-name form will display as shown in figure Write the new name here and clicks button to apply change or Clicks button to discard change. When user clicks below button, write set point form will display as shown in figure Write the new values here and clicks button to apply change or Clicks change. button to discard

15 Graph creation using data from the database. For that click on below figure: button and Trends form will display as shown in To choose the graph type selects the radio-button. Select start-date and end-date for graph from here. To see the graph click this button (after selecting instruments) Enter value here to set graph range. To maximize graph click this button To reset graph after maximize or minimize click this button To minimize graph click this button To export the graph click this button To the graph click this button To select instruments mark the check-box of that instrument. To set graph range click this button.

16 Report generation using data from the database. For that click on below figure: button and report form will be display as shown in To select instruments click this button Select start-date and end-date for report generation To see report click this button

17 To select instruments mark the check-box for that instrument Click this button to see selected instruments. Click this button to cancel instrument selection NOTE: Maximum 8 no of instrument you can select.

18 Report Output: Change System Settings NOTE:- (Only administrator can change system setting) 6.1) clicks on button and administrator login form will display as shown in figure below:

19 If administrator user-id and password are correct than system setting form will be display as shown in figure below: To change communication settings Select appropriate value from the given lists To change node address of instruments click this button To change log interval enter value here. To add user click here. To edit or delete user click here. NOTE: To lock or unlock user click here. After applying system changes Restart software. To restore software click here. To take software back-up click here. To change signature & report header click here.

20 Audit-trail report generation using data from database: Select start-date and end-date from here To see audit-trail report click here Click this button to see report.

21 Alarm report generation using data from database: Select start-date and end-date from here To see alarm report click here Click this button to see report.

22 To know about the company: To see profile of the company click here To know about the company click here