CBAM270 XETK ECU Adapter and Power Supply Cable, pre-assembled into PG9 screwing, shield on ECU-Housing, 1B PHE - JST PHR (10fc-5fc) / 0B PHG - JST PAP (2fc-2fc), 0m50 0m70 Data Sheet
Copyright The data in this document may not be altered or amended without special notification from GmbH. GmbH undertakes no further obligation in relation to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license. Using and copying is only allowed in concurrence with the specifications stipulated in the contract. Under no circumstances may any part of this document be copied, reproduced, transmitted, stored in a retrieval system or translated into another language without the express written permission of GmbH. Copyright 2018 GmbH, Stuttgart The names and designations used in this document are trademarks or brands belonging to the respective owners. Document CBAM270 R06_EN 2
Contents Contents 1 Introduction... 5 1.1 View... 5 1.2 Installation... 7 1.2.1 Selectable Cables for XETK... 7 1.2.2 Installation with Permanent Power Supply inside ECU not available.... 8 2 Technical Data... 9 2.1 Mechanical Dimensions... 9 2.2 Temperature Range... 10 3 Ordering Information... 11 4 Contact Addresses... 12 CBAM270 Data Sheet 3
Figures Figures Figure 1: View CBAM270-0m50 (Image similar)...5 Figure 2: View CBAM270-0m7...6 Figure 3: XETK Cables...7 Figure 4: Installation Cable...8 Figure 5: Dimensions CBAM270-0m50...9 Figure 6: Dimensions CBAM270-0m7...9 CBAM270 Data Sheet 4
Introduction 1 Introduction CBAM270-0m50 is a serial 100 MBit/s cable adapter with external power supply for XETKs. Preassembled into PG9 screwing, shield connected to the screwing. Usable for ECUs without Permanent Power Supply inside 1.1 View Figure 1: View CBAM270-0m50 (Image similar) CBAM270 Data Sheet 5
Introduction Figure 2: View CBAM270-0m7 CBAM270 Data Sheet 6
Introduction 1.2 Installation 1.2.1 Selectable Cables for XETK 10 (m) RJ45 CBE200-3 CBE200-8 PC XETK 10 (f) 10 (f) RJ45 CBAE200.2-1m2 PC CBAM230.1-0m38 CBAM230.1-0m28 CBAM240.1-0m6 CBAM270-0m50 CBAM270-0m7 CBAM271-0m50 10 (m) CBE230.1-3 CBE230.1-8 10 (m) 10 (f) 8 (m) CBAE330.2-0m5 ES600 ES910 Figure 3: XETK Cables CBAM270 Data Sheet 7
Introduction 1.2.2 Installation with Permanent Power Supply inside ECU not available. E.g. Cable CBE200 Cable K70 Permanent Supply 12V Cable CBAM270.0 12V Ignition Key Cable Gland Cable CBAM270.0 Serial ETK Interface Connector Power Supply Connector Pad for Power Supply or additional Power Connector Vehicle Wiring ca. 18 V Vehicle Battery ECU Connector ECU ECU GND ETK Figure 4: Installation Cable Note for using the cable with an ETK with solder pad, cut the plug and solder the wire direct to the solder pad. Note It is recommended for safety reasons to connect the external permanent voltage and the switched voltage inside the ECU! CBAM270 Data Sheet 8
Technical Data 2 Technical Data 2.1 Mechanical Dimensions All dimensions in mm. Figure 5: Dimensions CBAM270-0m50 Figure 6: Dimensions CBAM270-0m7 Note for mounting the cable, cut a PG9 thread into the ECU housing. For thin walled housings use a Nut SM-PE 9. Available from Lapp, Ordernumber: 52103210 CBAM270 Data Sheet 9
Technical Data 2.2 Temperature Range Condition Operating Temperature Temperature -40 C - +125 C CBAM270 Data Sheet 10
Ordering Information 3 Ordering Information Short Name Order - Number CBAM270-0m50 F 00K 107 866 CBAM270-0m7 F 00K 108 479 K70 Y 261 A24 942 CBAM270 Data Sheet 11
Contact Addresses 4 Contact Addresses HQ GmbH Borsigstraße 24 Phone: +49 711 3423-0 70469 Stuttgart Fax: +49 711 3423-2106 Germany WWW: www.etas.com Subsidiaries and Technical Support For details of your local sales office as well as your local technical support team and product hotlines, take a look at the website: subsidiaries WWW: www.etas.com/en/contact.php technical support WWW: www.etas.com/en/hotlines.php CBAM270 Data Sheet 12