ENCORE S226 and L226 Section II Parts and Service Manual (70200A) CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -27-
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM CAUSE ACTION There is no solution flow. The solution flow does not stop. The machine does not remove all the water from the floor. The solution tank is empty. The solution valve is closed. There is an obstruction in the solution hose or filter. The solution valve or electric wiring is damaged. The solution module is defective. The solution valve is open. The solution valve or wiring is damaged. The solution valve is dirty There is a damaged seat and washer in the solution valve. The solution module is defective. The squeegee is up. The squeegee tilt is not correct. The recovery tank is full. The screen filter is dirty. There is an obstruction or damage in the squeegee, squeegee hose or standpipe. The vacuum motor is not running. The squeegee hose is disconnected, or damaged The squeegee blade is damaged, worn, or incorrectly installed. The gaskets on the cover of the recovery tank are damaged. Fill the solution tank. Open the solution valve. Remove the obstruction from the hose or filter. Repair or replace the valve or the electric wiring. Replace solution module Close or Clean the solution valve. Repair or replace the valve and the wiring. Clean the solution valve. Replace the seat and washer. Replace solution module. Lower the squeegee. To adjust See Figure 11, page 23. Drain the recovery tank. Clean the screen filter. Remove the obstruction or repair the damage. Check for tripped breaker. Have an authorized service person make repairs. Check and connect hose. Turn or replace the squeegee blade. Correctly install the squeegee blade. Replace the gaskets. The batteries do not give the normal running time. The battery terminals are dirty or damaged. The electrolyte level is too low. The batteries are not fully charged. The charger is damaged. The battery is defective. The batteries are disconnected. Brush is in heavy scrub setting. Clean the terminals and connectors. Replace the damaged cables. Charge the batteries. Add distilled water to each cell and charge the batteries. Charge the batteries for a full 16 hour charge. Have an authorized service person repair the charger. Check voltage of each cell while discharging. Connect the batteries. Adjust Pressure. Page -2- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
PROBLEM CAUSE ACTION The cleaning is not even. The machine does not run. The scrub brush or pad is worn. There is damage to the brush assembly, caster or the solution valve. The brush motor is not running The solution level is low. The machine loses power. Key or switch is off. Batteries are unplugged. Battery terminals are dirty. Batteries are discharged Replace the scrub brush or pad. Have an authorized service person make the needed repairs. Check for tripped breaker. Reset. Check for loose connections. Fill the solution tank. NOTE: If the problem continues consult an authorized service person. Reset the circuit breaker. Turn key or switch on. Check the battery connections. Check battery gauge and recharge NOTE: If the problem continues consult an authorized service person. CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -29-
Encore S226/ L226 Final Assembly Drawing 11/23/00 1 2 3 27 2 26 31 27 32 30 6 2 29 7 9 1 2 10 11 23 22 20 19 9 10 11 12 21 17 1 13 16 1 10 11 Page -30- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Final Assembly Parts List 11/23/00 Qty Qty Ref. # Part No. Description L S 1 10062A Assembly, Recovery Tank 1 1 2 1006A Assembly, Control Panel L 1-10066A Assembly, Control Panel S - 1 3 3006A Rear Cover 1 1 010A Screw, 10-2 x ½ SS 7000A Plate, Warning 1 1 6 3010A Rivet, Pop 1 / 2 2 7 1006A Assembly, Rear Panel L 1-10067A Assembly, Rear Panel S - 1 9061 Washer, /16 Flat 11 11 9 920110 Nut, /16-1 ESNA 10 9062 Washer, /16 Lock 7 7 11 11A Screw, /16-1 x ¾ 7 7 12 10129A Assembly, Squeegee 32 1 1 13 1007A Assembly, Squeegee Lift 1 1 1 10069A Assembly, Traverse System L 1-10070A Assembly, Non-Traverse System S - 1 1 9092 Washer #10 2 2 16 10071A Assembly, Brush Head L 1-10061A Assembly, Brush Head S - 1 17 110A Nut, 3 /-16 ESNA 1 7031A Washer, 3 / Flat SS 19 096A Hinge 1 1 20 39A Screw, ¼-20 x 1 /2 SS 6 6 21 3009A Front Cover 1 1 22 0966A Latch, Front Cover Ref Ref 23 930090 Rivet, /32 x 9 /16 2 2 2 10063A Assembly, Solution Tank 1 1 2* Page 12 Battery 7133 Battery 12V, 19 AH (wet - UT Post) - 2 7133 Battery 12V, 19 AH (dry - UT Post) - 2 0136A Battery 6V, 20 AH (wet - Stud Post) 0137A Battery 6V, 20 AH (dry - Stud Post) 913 Battery, 6V 330 AH (wet - UT Post) 913 Battery, 6V 330 AH (dry - UT Post) 26 1206A Series Battery Cable (Taper Style) 3 3 1217A Series Battery Cable (Ring Style) 3 3 27 9020 Washer, /16 Fender 2 73A Screw, /16-1 x 2 2 2 29 739A Screw, /16-1 x 3 Hex 2 2 30 7026A Washer, ¼ flat SS 31 1211A Battery, Cable (Taper Style) 1 1 017A Battery, Cable (Ring Style) 1 1 32 1A Screw, ¼-20 x 3 / NI 10132A Lit Kit 1 1 NI 1731A Pad Driver Assembly 1-1010A Pad Driver Assembly - 1 NI 012A Battery charger 1 1 NI 77092A Label, Gases 1 1 NI 77093A Label, Falling 1 1 NI 70226A Label, Battery 1 1 NI 30070A Accessory Bag 1 1 NI 10072A Parking Brake Assembly "L" 1 - NI 10073A Parking Brake Assembly "S" - 1 * See page 12 for installation. CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -31-
Encore S226/L226 Recovery Tank Assembly Drawing /00 Drawing #10062A 1 2 3 3 2 1 6 A 0 3 7 9 B 10 39 37 3 3 36 20 19 3 7 1 17 16 12 26 33 1 30 2 27 2 31 16 1 1 13 11 32 2 23 21 29 22 #0 Recommended Torque 17 + or - inch pounds Page -32- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Recovery Tank Assembly Parts List /00 Ref. # Part No. Description Qty 1 96279 Screw, 10-2 x. 1 2 3007A Lid 1 3 1110A Nut, 10-2 SS 1 3006A Gasket, Lid 1 069A Strainer 1 6 3933A Stand Tube 1 7 3730 O-Ring 2 10660A Switch Kit, (Includes A, B, 9) 1 A 0002A Switch (included in Item ) 1 B 69A Relief, Strain (included in Item A) 1 9 977A Seal, Washer 1 10 30061A Tank, Recovery 1 11 60373A Latch, Recovery Tank 1 12 7622A Washer, Nylon /16 x / x 1/32 1 13 003A Screw,.2 x 20 x.2, Shoulder 1 1 60336A Strap, Hose Retainer 1 1 100A Screw, 10-32 x ½ SS Xylan Coating 2 16 3006A Hinge, Pin (included w/ item 10) 2 17 302A Housing, Connector(included in A) 2 1 109A Contact (included in A) 19 2100A Nut, Strain Relief Lock 1 20 72010 Clamp, Hose 1 21 316A Hose, Drain 1 22 32002 Clamp, Hose 1 23 3901 Valve, Drain 1 2 96293 Screw, -1 x ½ PN 1 2 2206A Chain 1 26 96297 Screw, 10-2 x 3/ Pan 1 27 33901 Drain, Valve Handle 1 2 3307 Gasket, Drain Valve 1 29 1060A Hose, Squeegee 1 30 3020 Squeegee Stand Tube 1 31 0110A Hose Clamp 1 32 72020 Hose Clamp 1 33 301A Housing, Vac Motor Connector 2 3 67110 Hose 1 3 72A Screw, ¼-20 x Hex 3 36 7026A Washer, ¼ Flat 3 37 109A Motor, Vacuum (3-Stage) 1 100A Motor, Vacuum, (2-Stage Option) 1 3 631 Gasket 1 39 33A Spacer 3 0 920797 Nut 1 1 962666 Screw, 10-2 x ¾ 1 2 920296 Nut, 10-2 Elastic 1 3 3020A Strap 1 NI 3910 Valve Asm. (includes 23, 2, 2, 26, 27, 2) 1 NI 70226A Label, Battery Installation 1 CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -33-
Encore S226/L226 Solution Tank Assembly Drawing /01 Drawing #10063A 19 20 21 2 23 2 1 1 2 3 17 16 12 22 9 10 6 11 7 13 1 Page -3- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Solution Tank Assembly Parts List /01 Ref. # Part No. Description Qty 1 72010 Clamp, Hose 1 2 096A Hose, Drain 1 3 30060A Tank, Solution 1 961A Valve, Battery Drain 1 722030 Clamp, Hose 6 6 303A Hose, Clear Vinyl 1 7 20207 Adapter, Hose 3/ MPT x ½ Hosebarb 1 3012A Hose, Stretch 2 9 120A Adapter, Female 1 10 317 Filter, Screen 1 11 3021 Adapter, Male, ¾ Barb x GHT Male Thread 1 12 120A Valve, Solution 1 13 979A Valve, Solution 1 1 301A Splitter 1 1 1109A Nut, -32 ESNA SS 2 16 0966A Latch 1 17 010A Screw, -32 x 1¼ SS 2 1 0963A Screen, Fill (with hose retention) 1 130A Strainer (without hose retention) 1 19 6979A Bracket, Latch 1 20 17092 Washer, Lock ¼ 2 21 17091 Screw, ¼-20 x ¾ SS Hex 2 22 109A Valve Assembly, Solution Shut-Off (incl. #9,12) 1 23 600A Bracket, Hose 1 2 136A Spring, Hose 1 2 010A Screw, 10-2 x ½ 2 NI 30162A Funnel (included w/kit 10177A) 1 NI 10177A Kit, Solution Fill 1 (includes #1-130A)(includes NI - 30162A) CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -3-
Encore S226/L226 Rear Panel Assembly Drawing /00 Drawing #1006A (L) Drawing #10067A (S) 1 2 1 2 36 3 3 3 32 3 6 7 9 33 9 10 31 9 10 10 6 29 2 27 3 11 30 3 10 11 1 37 16 17 16 1 26 2 2 1 1 21 20 19 23 2 22 13 12 Page -36- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Rear Panel Assembly Parts List /01 Ref. # Part No. Description Qty Qty L S 1 92022 Nut, 10-32 2-2 90603 Washer, Starlock 2 3 92006 Nut, 6-32 6106A Rectifier 1-0133A Harness, Power L 1-013A Harness, Power S - 1 6 962212 Screw, 6-32 x 7/ 3 2 7 33A Screw, 10-32 x ¾ 1-110A Solenoid, Brush 1 1 9 39A Screw, ¼-20 x ½ 6 6 10 9061 Washer, Starlock, ¼ 10 10 11 391A Screw, ¼-20 x / 12 60261A Panel, Rear Metal 1 1 13 6027A Cable, Squeegee Lift 1 1 1 92036 Nut, Pal 1 1 1 002A Bolt, Shoulder, /16 x 1.0 1 1 16 90692 Washer, Flat /16 SS 2 2 17 3360 Spring 1 1 1 6901A Lever, Squeegee Lift 1 1 19 690A Handle, Squeegee 1 1 20 90666 Washer, 3/ Starlock 1 1 21 39A Screw, 3/-16 x / 1 1 22 663A Plate, Vacuum Wear 1 1 23 96296 Screw, 10-2 x ½ 2 2 2 61260A Plate, Squeegee Lift 1 1 2 737A Switch, Vacuum Lever 1 1 26 601A Screw, 6-32 x 1¼ PN 2 2 27 1217A Nut, ¼-20 x.21h Nylock 1 1 2 6026A Bracket, Power Connector 1 1 29 116A Cable, Assembly Console 1 1 30 19391 Grommet, slotted, Ref Ref 31 111A Solenoid, Main 1-110A Solenoid, Main - 1 32 017A Harness, Traverse 1-33 0169A Solenoid, Vacuum 1 1 3 96279 Screw, 10-2 x ½ 2 3 0132A Control, Traverse 1-36 1097A Low voltage Shutoff - 1 37 30097A Insulator, Mylar 1 1 NI 77093A Label, Falling Parts 1 1 NI 77092A Label, Gases 1 1 NI 709A 3/ Ring Terminal, 1-16 - 1 NI 911933 #10 Ring Terminal, 1-16 - 1 NI 019A Ring Terminal, /16-1 CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -37-
Encore S226/L226 Control Panel Assembly Drawing /00 Drawing #1006A "L" and 10066A "S" 1 2 27 2 3 29 7 30 3 37 36 3 6 36 3 7 11 12 10 11 1 0 33 32 31 27 19 1 1 16 116 3 26 30 2 39 16 16 1 1 17 2 2 23 22 20 9 21 Page -3- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Control Panel Assembly Parts List /00 Qty Qty Ref. # Part No. Description L S 1 13A Key (included w/item 3) Ref Ref 2 237A Screw, 10-32 x ½ 2 2 3 730A Switch, Key 1 1 6033A Panel, Key Switch 1 1 010A Screw, 10-2 x ½ SS Black Xylan 6 702A Washer, Switch 1 1 7 962262 Screw, Set -32 x ½ (included in item 29) 2 0962A Traverse, Control Knob 1-9 703A Screw, 10-00 x ½ PN 1 1 10 96297 Screw, 10-16 2-11 013A Harness, Potentiometer Assembly. 1-12 6029A Bracket, Traverse Switch 1-13 90666 Washer, 3/ Starlock 1-1 01A Switch, Reverse 1-1 90603 Washer 2 16 92022 Nut, 10-32 Hex 2 17 30062A Control Handle 1-30072A Control Handle - 1 1 391A Screw, ¼-20 x 1 /2 SS Ref Ref 19 7026A Washer, ¼ SS Ref Ref 20 30B Control, Solution 1 1 21 122A Breaker, Circuit 2 Amp Traverse 1-22 133A Breaker, Circuit 0 Amp Brush 2 2 23 1A Breaker, Circuit 30 Amp Vac 1 1 2 123A Breaker, Circuit Amp Actuator 1 1 2 7016A Label, Control L 1-7017A Label, control S - 1 26 602A Panel, Control, Metal 1 1 27 0217B Meter, Battery 1 1 2 016A Switch, Brush Adjustment 1 1 29 02A Knob 1 1 30 107A Meter, Brush 1 1 31 962330 Screw, 6-32 x 3 / 32 9060 Washer 33 3006A Housing, Switch & Lever 2 2 3 300A Lever, Switch 2 2 3 0961A Spring, Switch 36 0126A Switch, Forward/Reverse 2 2 37 010A Screw, 10-32 x ½ SS Black Xylan 3 70219A Label, Key Switch 1 1 39 326A Gasket, Panel 1 1 0 30096A Gasket, Switch 1 1 NI 770A ¼ F.I.M.Q.D. 2 NI 7712A ¼ F.I.F.Q.D. 1 0 NI 912226 Meter, Hour (Optional) CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -39-
Encore S226/L226 Squeegee Lift Assembly Drawing 6/00 Drawing # 1007A 1 1 20 21 19 12 22 6 2 3 17 6 1 16 1 1 10 9 7 13 1 11 Page -0- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Squeegee Lift Assembly Parts List 6/00 Ref. # Part No. Description Qty 1 61263A Bracket Tube 1 2 730A Screw, 3/-16 x 1¼, Hex SS 1 3 9063 Lockwasher, 3/ LT Spring Type 1 6960B Bracket, Pin 1 7026A Washer, ¼ SS 2 6 17091 Screw, ¼-20 x ¾ 7 9621 Screw, ¼-20 x 1¼ Hex 2 7031A Washer, 3/ Flat 3 9 92020 Nut, ¼-20 2 10 1111A Nut, 3/-16 ESNA 1 11 0101A Screw, ¼-20 x 3¼ SS 1 12 11A Screw, /16-1 x ¾ 1 13 6767A Nut, spacer 1 1 6026A Squeegee, Pivot Arm 1 1 110A Nut, ¼ Nylock 16 602A Bracket, Squeegee 1 17 6032A Mount, Squeegee 1 1 1112A Nut, /16-1 Thin ESNA SS 1 19 Page 37 Cable, Squeegee Lift Ref 20 Page 37 Lift Handle Assembly Ref 21 92036 Palnut Ref 22 9061 Washer 1 CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -1-
Encore S226/L226 Squeegee Assembly Drawing 10/00 Drawing # 1006A and 10129A 6 1 2 19 3 1 20 7 17 9 10 11 12 13 1 16 1 Page -2- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Squeegee Assembly Parts List 10/00 1006A 39" 32" Ref. # Part No. Description Qty Qty 1 962720 Screw, ¼-20 x ½ Hex SS 2 9067 Washer, ¼ Lock 3 6023A Bracket, Squeegee Wheel 2 2 3009B Wheel, Squeegee 110A Nut, ¼-20 2 2 6 602A Bolt, Shoulder /16x 2¼ 2 2 7 09A Ring, 3 / ID Snap 2 2 300A Wheel, Guide, Inch Diameter 2 2 9 60272A Channel, Squeegee Weldment 39 1-6023A Channel, Squeegee Weldment 32-1 10 03A Latch, Squeegee Clamp 1 1 11 93006 Rivet, 3/16 x.0 Aluminum 2 2 12 6022A Strap, Clamp, Squeegee Retainer 39 1-60232A Strap, Clamp, Squeegee Retainer 32-1 13 30069A Blade, Rear, Gum Rubber, 39 1-30067A Blade, Rear, Gum Rubber, 32-1 1 300A Spacer, Squeegee 39 1-3007A Spacer, Squeegee 32-1 1 30091A Blade, Front Ribbed 39 1-30066A Blade, Front Ribbed 32-1 16 0011A Screw, 3 /-16 x 3 2 2 17 1301A Nut, 3 /-16 Jam SS 2 2 1 3260B Gasket 1 1 19 2201A Knob 2 2 20 603A Shim, Squeegee Wheel 2 2 10129A CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -3-
Encore S226/L226 Frame Axle Assembly Drawing 11/23/00 Drawing #10069A and 10070A 22 20 Page -- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Frame Axle Assembly Parts List 11/23/00 Traverse Non-Traverse Ref. # Part No. Description Qty Qty 1 700A Screw, ¼-20 x 1 1-2 11A Screw, /16-1 x ¾ 6 6 3 9062 Washer, /16 Lock 6 9061 Washer, flat /16 6 6 6032A Squeegee Mount Ref Ref 6 60260B Frame Assembly 1 1 7 096A Caster, Assembly 1 1 30071A Wheel Assembly 2-6920A Wheel, Non Traverse - 2 9 0967A Transaxle w/mounting hubs 1-60266A Non-Traverse Axle Assembly - 1 10 6029A Mount, Transaxle 2-11 7031A Washer, flat 3 / SS 12 1703 Washer, 3 / Lock 13 0103A Screw, 3 /-2 x 1 Hex SS 1 723A Ring, Snap Retainer - 2 1 7616A Washer, Nylon - 2 16 9020 Washer, /16 Fender 2 2 17 962620 Screw, /16-2 x ¾ - 2 1 7026A Washer, Flat, ¼ SS - 19 1217A Nut, ¼-20 SS Thin 9-20 3711B Wheel Cover 2 2 21 39A Screw, ¼-20 x ½ SS 2 2 22 9061 Washer, ¼ Starlock 2 23 979A Valve Solution Ref Ref 2 110A Nut, 3 /-16 ESNA Ref Ref 2 7031A Washer, Flat 3 / SS Ref Ref 26 Ref Solution Tank Ref Ref 27 9020 Washer, /16 Ref Ref 2 73A Screw, 3 /-16 x 2 Ref Ref 29 69639A Strap, Static 1-30 1013A Hub, Transaxle (includes #9) 31 77267A Label, Tie Down 32 110A Nut, 3 /-2 ESNA CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page --
Encore S226/L226 Brush Head Assembly Drawing /00 Drawing #10071A and 10061A 1 2 1 6 7 3 77 9 10 72 71 70 69 67 6 21 9 60 6 7 76 7 6 63 62 7 2 61 6 73 66 1 17 11 12 16 1 13 1 3 7 6 20 19 11 1 21 22 23 31 1 2 30 0 9 6 0 1 39 2 2 7 3 2 0 3 37 1 3 37 31 32 36 33 29 2 26 27 3 2 2 3 Page -6- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Brush Head Assembly Parts List /00 Drawing #10071A and #10061A Qty Qty Ref. # Part No. Description L S 1 370A Washer, Spacer Nylon 2 2 2 090A Actuator 1 1 3 6026A Plate, Nut 2 2 737A Switch, Lever 1 1 722B Switch, Whisker 1 1 6 9060 Washer, #6 7 96290 Screw, 6-32 x 1 6021A Mount, Switch 1 1 9 201A Pin 1 1 10 60236A Bracket, Brush Head 1 1 11 76670 Pin, Hair 12 3A Screw, ½ x 20 x 1½ 13 90673 Washer * * 1 630A Bar, Linkage 1 6770B Bearing, Sleeve 16 92027 Nut, ½-20 SS 17 90626 Washer, ½ Lock 1 0100A Screw, ½-20 x 1 Hex Head 19 0091A Pin, Brush Lift 1 1 20 60239A Mount, Brush Head 1 1 21 1217A Nut, ¼-20 ESNA.21 Height 3 3 22 6033A Bracket, Brush Housing 1 1 23 17091 Screw, ¼-20 x ¾ SS 2 2 2 72002 Clamp, Hose 2 2 2 110A Nut, ¼-20 ESNA 7 7 26 370A Hose, Solution 2 2 27 722030 Clamp, Hose 2 2 2 96299 Screw, ¼-20 x 1½ 2 2 29 301A Solution Splitter Ref Ref 30 6023A Plate, Brush Head 1 1 31 962992 Screw, -32 x / SS 32 721A Latch, Brush Housing 1 1 33 3003A Housing, Left Brush 1 1 3 3001A Skirt, Left 1 1 3 616A Screw, 10-32 x / SS 12 12 36 200A Nut, T 10-32 12 12 37 1109A Nut, -32 SS ESNA 3 60337A Plate, Latch Brush 2 2 39 Page 2 Brush/Pad Assemblies * Used only as required to square up linkage bar #1 to the frame. Qty Qty Ref.# Part No. Description L S 0 96271 Screw, /16-1 x ¾ Soc. 2-11A Screw, /16-1 x ¾ Hex - 2 1 300B Gimbal Male 2-2030A Motor, Adapter - 2 2 616A Gimbal, Collar 2-3 96A Washer, Rubber 2-9062 Washer, /16 Lock - 2 90210 Washer, Impeller - 2 6 90679 Washer, Spacer - 2 7 9622 Screw, 3/-16 x ¾ 9063 Washer, Lock 3/ 9 3002A Skirt, Right 1 1 0 300A Housing, Right Brush 1 1 1 1A Keeper 1 1 2 7039A Washer, ¼ 2 2 3 300A Wheel, Guide 1 1 602A Sleeve Guide Wheel 1 1 301A Screw, ¼-20 x 1¼ 1 1 6 2001A Spacer, Brush Tilt - 2 7 91102 Key (included w/item ) 2 2 09B Motor, Brush 2 2 9 1602A Housing 60 1601A Connector 61 6020A Bushing, Swivel Adj., ¼ 62 039A Pin, Plunger 1 1 63 096A Spring, Plunger 1 1 6 097A Knob 1 1 6 6021A Bushing, Swivel, 3/ 1 1 66 110A Nut, 3/-16 SS ESNA 1 1 67 322A Spring, Head Pressure 1 1 6 7007A Washer, Flat, ¼ 1 1 69 6023A Tube, Head Pressure 1 1 70 6029A Switch, Actuator 1 1 71 0102A Washer, ¼ 1 1 72 702A Screw, ¼-20 x 1¾ 1 1 73 7031A Washer, 3/ Flat Ref Ref 7 0109A Nut, ½-20 Jam S.S. 7 90603 Washer, #10 2 2 76 010A Screw, 10-2 x ½ 2 2 77 30092A Insulator, Mylar 1 1 NI 77091A Label, Moving Parts 2 2 CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -7-
Encore S226/L226 Optional Brake Drawing and Parts List 11/23/00 10073A - "S" Model 1 1 11 1 7 2 3 16 1 2 7 1 6 1 13 9 11 1 12 6 11 10 7 6 12 11 Ref. # Part No. Description Qty 1 11A Screw, /16-1 x ¾ 2 2 6039A Pad, Brake 2 3 60271A Brake, Bar L.H. 1 920110 Nut, /16-1 ESNA 6 9061 Washer, Flat, /16 10 6 6777A Spacer 3 7 1A Screw, /16-1 x 1¼ 3 6026A Lever, Brake Pedal 1 9 60361A Cam, Brake 1 10 60267A Rod, Brake 1 11 110A Nut, ¼-20 ESNA 12 0 Swivel, Rod, Brake 2 13 7026A Washer, Flat, ¼ 1 1 0969A Spring, Brake Asm. 2 1 7607A Washer, Flat Nylon 16 60362A Brake, Bar R.H. 1 NI 77266B Label, Parking Brake 1 Page -- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Optional Brake Drawing and Parts List /01 10072A - "L" Model 3 2 6 1 7 Ref # Part No. Description Qty 1 091A 2 603A Spacer 1 3 3009A Tie, Cover Retainer 1 0123A Nut, Brake Drive 1 012A Key, 3/32 Sq. x 1/ Lg. 1 6 3009A Cover, Vinyl 1 7 012A Screw Set (Brake Nut 2 to Motor Shaft) 10160A Brake, Asm. 2V 1 NOTE: Only use spacer (ref. #2) on transaxles that have a circular step and mounting nuts protruding from end of motor. The motor that uses the spacer can be identified by the motor brush caps protruding past the outside diameter of the motor. CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -9-
Encore S226/L226 Vacuum Motor Drawing and Parts List Drawing /00 TO Page -0- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Gearbox Assembly Drawing and Parts List /00 Form #23A 9 6 7 1 2 3 Ref # Part No. Description Qty 1 76A Ring, Snap 1 2 0761 Seal, Oil, Small 1 3 200A Cap End 1 666A O-Ring 1 1176a Bearing, Large 1 6 316A Shaft & Gear 1 7 90260 Bearing, Small 1 3A Housing 1 9 1A Seal, Oil Large 1 10 NI Darina EP2 Grease oz. CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -1-
Encore S226/L226 Brush Motor Drawing & Parts List /00 Motor Asm. 09B 13 7 12 1 2 12 13 Seam Location 3 1 16 1 6 17 9 10 11 Item Part No. Description Qty 1 67A Stator Frame Assembly (w/magnets & Clips) 1 2 012A Armature Assembly (w. B.E. & F.E. Bearings) 1 3 9026 Bearings B.E. 1 9020 Bearing F.E. 1 * Commutator Bracket Assembly 1 (w/brush BRD Assembly Leads) 6 020A Commutator Bracket 1 7 60A Strain Relief 2 9626 Brush Board Screw 2 9 017A Brush Board Assembly (w/ Springs & Brushes) 1 10 396 Brush Spring 11 026A Brush Assembly 12 67A Lead Assembly 1 13 66A Lead Assembly 1 * 1 Helical Washer 1 1 01A Thru Bolt 2 16 001A Shaft Key 1 17 23A B.E. Bracket Assembly (Gear Box) 1 * NOTE: Parts not available at this time. Page -2- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore S226/L226 Transaxle Drawing /00 CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -3-
Encore S226/L226 Battery Charger Drawing and Parts List /00 WARNING: All electrical repairs must be performed by qualified personnel only. Charger #012A: 2 volt, 2 amp D.C., 11 volt, A.C., 60 Hz. Charger #013A: 2 volt, 2 amp D.C., 230 volt, A.C., 0 Hz Charger Charger Ref. No. Description 012A 013A 1 Charger Case 1129A 112A 2 Transformer 13A 09A 3 Electronic Controller Kit 700A 200A Capacitor, 660 V.A.C. 912132 912132 Heat Sink Assembly 912212 912212 6 Ammeter 0200A 0200A 7 Fuse Holder 91232 91232 Strain Relief, A.C. Cord 372 372 9 Strain Relief, D.C. Cord 773 773 10 D.C. Cord Assembly 196A 196A 11 A.C. Cord Assembly 197A 9097 12 Housing, Red 91170 91170 13 D.C. Plug Lock Key 79020 79020 * NOTE: Parts not available at this time. Page -- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226
Encore L226 Connection Diagram (0090A - W) 6/00 CLARKE TECHNOLOGY Operator's Manual - Encore S226/L226 Page -7-
Encore L226 Electrical Schematic (0090A-E) /01 Page -- CLARKE TECHNOLOGY Operator's Manual -Encore S226/L226