Works Commissioning Interfce Importnt: Retin these instructions CONTENTS 1 Unpcking... 1 2 Storing... 1 3 Instlltion... 1 4 Uninstlling the USB Drivers... 8 5 Disposl... 8 1 UNPACKING Instlltion Instructions TG200817 2 STORING -10 C (14 F) +50 C (122 F) 0 0 %RH 95 %RH 3 INSTALLATION 1 Dimensions (mm) 6-4 2 Requirements 0 C (32 F) +to 45 C (113 F) + 1 0 0 %RH 95 %RH 92 mm (3.6 ) b + 1 27 mm (1.1 ) 74 mm (2.9 ) Protection :IP20 TG200817 Issue 1/C 03/08/06 1
3 Instll USB Drivers (If not lredy Instlled) Windows XP Insert Drivers CD. b Follow instructions on screen. The following dilogue box is displyed. Windows 2000 Insert Drivers CD. b Follow instructions on screen. c d e Click Continue Anywy. The instlltion will continue. The dilogue box is displyed gin click Continue Anywy. The instlltion will continue. The instlltion is complete when ll dilogue boxes dispper. 4 Connect to PC Cution: Do Not remove the USB connector during use. USB Cble supplied Type A Type B Note tht the my only be used to ccess locl IQ system, connection to remote systems using TMN or other similr communiction nodes is not supported. 5 Hrdwre Instlltion Once the is connected to USB port for the first time the PC will instll the new hrdwre. This process vries depending on the operting system. Note tht connecting the to different USB port cuses the hrdwre instlltion to occur gin. Windows 2000 When the is connected to the USB port (see (4)) the following dilogue box is displyed. b c The dilogue box will chnge indicting the progress of the instlltion. This process repeted. When no more dilogue boxes re displyed the instlltion is complete. 2 TG200817 Issue 1/C 03/08/06
) 5 JH= JA C O 1, 5 A HE=! " # $ % & ' 5 4 8! " # + 2 1! " # " 8 " 8 5 " 8 =? ) 5 JH= JA C O 1, 5 A HE=! " # $ % & ' 5 4 8! " # + 2 1! " # " 8 " 8 5 " 8 =? 5 Hrdwre Instlltion (Continued) Windows XP When the is connected to the USB port (see (4)) the following dilogue box is displyed. c Select Instll the softwre utomticlly (Recommended) nd click Next >. The following dilogue box is displyed. d Click Continue Anywy. The following dilogue box is displyed. b Select No, not this time nd click Next >. The following dilogue box is displyed. e f Click Finish. The process is repeted. When the dilogue box bove is displyed for the second time click Finish. 6 Connect to either: If connecting to LINCs,LONCs, IQLRouters or to IQLs with squre two prt connector (ll IQLs excluding older /24VAC versions of IQL10 to IQL13). Remove connector IQL, LINC, or LONC b Connect dpter cble 10 L two terminl femle cble supplied four terminl mle squre two terminl femle TG200817 Issue 1/C 03/08/06 3
, 2 M A H L " L =? @? 2 =? A J 2 M A H. 6 6 A JM H 5 E@ A )! " ) 5 5 JH= JA C O 1,,,!, ", #, $, % + " 8 1 + " 8 + 5 E@ A ) 9 H I 4 K JA H. 6 6 A JM H 5 E@ A *! " 5 E@ A * 2 E " 8 =? 6-4 2 M A H L " L =? @? 2 =? A J 2 M A H. 6 6 A JM H 5 E@ A )! " 5 E@ A ) 9 H I 4 K JA H. 6 6 A JM H 5 E@ A *! " 5 E@ A * 2 E 6 Connect to (Continued) or: If connecting to device with with round two prt connector (e.g.older LONROUTER). Remove connector b Connect dpter cble LONROUTER disconnected cble supplied two terminl femle four terminl mle squre or: If connecting to device with single prt connector (e.g.older /24VAC versions of IQL10). 1 3 two terminl femle screw wires into terminls Do not llow wires to cross on loop 7 Check on + 1 LON OK (green) Flshes every 24 s, ON fter 1½ mins (Check, LINCs) Note tht the LON OK LED will be extinguished if there is problem with the cble, or power is not being supplied by the USB cble. 4 TG200817 Issue 1/C 03/08/06
8 Identify COM port Before it is possible to communicte with the it is necessry to find out the COM port number ssigned to the USB port so tht it cn be specifed when setting up the softwre to communicte using the. b c Right click My Computer nd click Properties from the displyed menu. The System Properties dilogue box is displyed. Click the Hrdwre tb nd then click Device Mnger. The Device Mnger is displyed. Click + next to Ports (COM & LPT) nd check the port number ssigned to Novr Trend USB. Note tht ech USB port is ssigned different COM port number. 9 Set Up Softwre Configure the softwre to communicte with the IQ System using the. It is necessry to set the softwre to communicte using the COM port ssigned to the USB port see (10) t bud rte of 19200. For detils of how to do this see the documenttion supplied with the softwre. TG200817 Issue 1/C 03/08/06 5
10 Configure (If required) The will operte out of the box under norml circumstnces; only chnge prmeters if necessry. Configure using suitble softwre tool (e.g. text comms window in SET) nd text comms to ddress 10 Ln 0 or ddress 0 Ln 0. Set bud rte to 19k2. Prmeter Setting Function Only chnge if R(..ddress L - own ddress Defult=119 N - own LN Defult= 1 Device ddress of Ln number of D - identifier " " Identifier ttribute of r - Works retry time i- Works interpcket dely if more thn 1 being used if more thn 1 being used For lrm ident 750 ms Time (ms) between messge See Trend Works Products retrnsmission following non- Engineering Mnul for detils cknowledgement. 75 ms Time (ms) between frmes of dt in multi-frme messge. - Works service clss 2 Defines whether messges re r e p e t e d n d w h e t h e r c k n o w l e d g e m e n t s r e e x p e c t e d. 2 s p e c i f i e s cknowledgement nd repet if not cknowledged up to three times. b - Works Buffer size b u f f e r s i z e Specifies the size of messe I f r o u t e r s s e p rte I Q L s, (bytes) Defult = 146 frmes sent on. LINCs, LONCs nd hve buffer size smller tht 146 bytes - set to smllest buffer size. (minimum = 66) m - Works Messge code code number. Code used by IQLs, LINCs, If messge code being used by Defult = 64 LONCs, ll LINCs/LONCs must use sme code. other users - must be exclusive to IQ System. v - Ntive messging 0 Setting to 1 enbles to If using with specil ntive send nd receive Works messging softwre tools. messge frmes in encoded f o r m t. 0 = d i s b l e d, 1=enbled. p - Send service PIN 0 Setting to one cuses to To generte messge to instll send service PIN messge to on LMT, or to identify to nd set itself bck to 0. system. M - Termintor Stte d e f u l t = O (OFF) Setting to I turns termintor on the 's Only turn ON if experiencing c o m m u n i c t i o n s problems.the termintor cn lso be tur ned ON by pressing the Termintor button. TARP z - Reset Node Flg d e f u l (ON) t = I Setting to O turns TARP OFF Set to O in most situtions. If there is one or more, LINC or LNC2 on the section, there could be IQs on ttched Ln(s) nd their ddresses cn only be found by using TARP nd so TARP should be set to I. s, LINCs nd LNC2s which do not shre the sme section do not need TARP, so TARP should be set to O When set to 1 the resets Set to required vlue to reset nd clers the node sttus nd infomtion. comms sttistics. When set to 2 the node sttus nd comms sttistics re clered. 6 TG200817 Issue 1/C 03/08/06
6-4 11 Configure (Continued) If Communiction problems Press Termintor Button. Termintor LED illumintes. + 1 12 Instll using Works Network Mnger Tool If System lredy instlled on Network MngerTool Or If one Trend device is instlled, ll must be instlled. When instlling in Works tool, send service pin messge when requested using configurtion prmeter p s described bove in step. Note this will be sent to not to RS232 port. See Works network mngement tool mnul. See Trend Works Products Engineering Mnul TE200292. Works System Integrtor must hve Works engineering expertise. 13 Test system 14 De-instll from Works Network Mnger Tool IqlTool 2 If removing from system when previously instlled. + 1 IqlTool for precommissioning, e.g. re-ddressing IQLs, chnging ttributes, checking I/O. 13 13 13 See Works network mngement tool mnul. See Trend Works Products Engineering Mnul TE200292. Works System Integrtor must hve Works engineering expertise. TG200817 Issue 1/C 03/08/06 7
4 UNINSTALLING THE USB DRIVERS If required the drivers cn be completely removed from the system by following the procedure below: 1 Disconnect 2 Disconnect Close ll pplictions using the port. Type A Type B 3 Uninstll Drivers 4 Delete Driver Files Run FTDIUNIN.EXE locted in the windows system directory. Delete the c:\progrm files\trend control system\-usb Drivers directory. 5 DISPOSAL WEEE Directive : At the end of their useful life the pckging, nd product should be disposed of by suitble recycling centre. Do not dispose of with norml household wste. Do not burn. Mnufctured for nd on behlf of the Environmentl nd Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37,Switzerlnd by its Authorized Representtive, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publiction from time to time nd mke chnges to the content hereof without obligtion to notify ny person of such revisions or chnges. Trend Control Systems Limited P.O. Box 34, Horshm, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 21888 Fx:+44 (0)1403 241608 www.trend-controls.com Trend Control Systems USA 6670 185th Avenue NE, Redmond, Wshington 98052, USA. Tel: (425)897-3900, Fx: (425)869-8445 www.trend-controls.com 8 TG200817 Issue 1/C 03/08/06