ARRIS Zhao Yun Pro User Manual. Content

Transcription

1 ARRIS Zhao Yun Pro User Manual Thank you for buying ARRIS Zhao Yun Pro 3-Axis brushless Gimbal. Each gimbal has been adjusted and tested before we send it out. For this gimbal, Most customers can plug and play when you receive it (Except for some multicopters, you may need to adjust some parameters). Here we suggest the customers to minimize the vibrations of the multicopter, for most of the vibration on the image of the video caused by the multicopter. In order to get the best performance of the gimbal, please read the user manual carefully. We will not be responsible for the damage of the gimbal or other equipment caused by improper operation. Content 1. ARRIS Zhao Yun Pro Introduction 2. Important Notes 3. How to Install the Camera 4. How to Intall the GoPro 5. Zhao Yun Pro 3-Axis Gimbal Connectors 6. How to Connect the User Manual Control Wire 7. Real-Time Video Output Solutions 8. How to Connect the Wires with the Video TX/RX Systems 9. How to Adjust the Parameters in Software 10. How to Set the Follow Mode in SimpleBGC GUI 11. How to Set the Lock Mode in SimpleBGC GUI 12. Frequently Asked Questions 13. Product Specifications 1

2 1. ARRIS Zhao Yun Pro Introduction ARRIS Zhao Yun now is compatible with most of the micro DSLR cameras and GoPro. (For GoPro, you need to purchase the mounting case separately.) For all of the cameras, we suggest using the prime lens for aerial photography. If you use other lens, we could not assure stable performance of the gimbal. The main controller we use on ARRIS Zhao Yun is legitimate BaseCam SimpleBGC brushless gimbal controller 32 bit version. And the firmware is the latest V2.40 version. With this controller, it is more stable, and customer can get firmware upgrade from the website (If customers upgrade the firmware or adjust the parameter by yourselves, we could not provide future technical support, but you can go to Zhao Yun Pro Brushless Gimbal is a 3-Axis brushless Gimbal, it can be used on Hexa-copter and Octa-copters. ARRIS Zhao Yun is one great FPV equipment designed for FPV enthusiasts. 2. Important Notes 2.1 Although we designed reasonable damping structure for ARRIS Zhao Yun Pro, please minimize the vibration of the multicopter before you install the Zhao Yun on it, or the vibration may influence the performance. We provide two kinds of damping balls for ARRIS Zhao Yun Pro, one is hard, and the other is quite soft. The one we install on the gimbal is the hard one, this is better for the multicopter with small vibration. And for the soft damping balls, it is good for the multicopter with bigger vibration. But with the soft damping ball, the performances will not as good as the hard one when the multicopter sways a lot. We suggest the customers use the hard damping balls if possible. 2.2 ARRIS Zhao Yun Pro needs 12V power supply. You can power it by a separate battery or the battery on the multicopter. Make sure it is 12V when you power it, lower or higher than 12V, the gimbal may not work properly. 2.3 After you power it, please remain the gimbal still for several seconds,, it needs time to do the initialization. 2.4 When the gimbal is power on, please do not plug or unplug the motor wire and manual control wire, this may burn the main controller of the gimbal. 2

3 2.5 Try to avoid using the gimbal on dusty or sand places; those items may enter the motor. If you do not notice them and run the gimbal, they may burn the motors. 2.6 When you use the gimbal, make sure you tighten the camera. If the camera is not tightening enough, it may cause the high frequency vibration. 2.7 The connector on Zhao Yun Pro is JST, 1 (black) is negative electrode, and the other 1 (red) is positive electrode. Pay attention to the electrode, if you connect the wrong side, it may burn the main board. 2.8 Before you power on it, please check the wires of the gimbal. Make sure the wires are not twined, the gimbal can move without any block. 2.9 Before you power on the gimbal, please install the camera on it If you want to use all the functions of ARRIS ZHAOYUN Pro 3-Axis, you need to make sure there are 4 extra Channel on the Radio In order to ensure the normal operation of ARRIS ZHAOYUN Pro 3-Axis, YAW should connect with radio and do some setting. Then the gimbal can adjust the direction effectively Before the initialization of the ZHAOYUN Pro 3-Axis, please make sure that the front of the gimbal stays the same direction as the front of the multicopter. If there is some deviation after you power the gimbal, we suggest you use the radio to adjust the direction of the gimbal. If the gimbal does not connect with the radio, the default mode is Follow Mode. If the gimbal connects with the radio set, the gimbal mode is decided by the mode switch In any mode, you can manual control the direction of the Yaw Axis of the gimbal. 3. How to Install the Camera 3.1 Install the camera in the frame of the gimbal, put the back of the camera close to the back of the gimbal. 3

4 3.2 Screw the bottom of the camera by bolt. If the bolt is too long, you need to use the carbon fiber shim comes in the accessories bag 3.3 Fix the camera by the metal column to the frame, here you need2 M3 X 6 screws. Tighten it is OK. There are 3 holes where you can install the metal column, and the column can move from front to back. For different cameras, you can choose the proper position for it. 4

5 3. How to Install the Gopro3/3+ It is easy to install the GoPro on ARRIS Zhao Yun Pro gimbal, you just need the mounting case which is specially designed for GoPro by ARRIS. The extra weight of the mounting case makes the gravity center of the gimbal more reasonable. When you use the bolt to screw it, please use the carbon fiber shim comes in the accessories bag. 5. ARRIS Zhao Yun Pro 3-Axis Gimbal Connectors SH---Shutter VO---Video Output Yaw---Yaw CMD--- Mode Switch Roll---Roll Pitch---Pitch Power--- 12V Power 5

6 Note: Please pay attention when you connect the wires. Except the power pins, there are two row pins. The upper pins refer to signal wire. The lower pin is GND. 6. How to connect the Manual Control Wire 6.1 Get the manual control wires comes with the gimbal 6

7 6.2 Connect the manual control wire with gimbal and the receiver like the following picture: Notice: For Mode Switch, please use band switch, such as the A in following picture. And for Yaw, Roll and Pitch, please use the stick or knob which has the function of return to central point. Such as the stick C and knob B in following picture. The picture below is how to plug wire on Futaba T8FG receiver. 7

8 The picture below is the settings in Futaba T8FG:. Here we will introduce the CH on the receiver where the wire plugged: Function on Receiver Channel ARRIS Zhao Yun Pro FutabaT8FG Roll Pitch YAW Mode Switch 1 AIL 2 ELE 4 RUD 5 GEAR Shutter 6 VPP 8

9 The function of ARRIS ZHAOYUN Pro 3-Axis on Futaba T8FG:. 7. Real-time Video Output Solution (Support Sony Nex series Cameras and GoPro 3 ) To output the video from camera in real time during the aerial photography, we have efficient solutions for Sony series cameras. Just use the video TX/RX system and the HDMI to AV cable, then you can output the video from the camera in real time. The relevant equipment can buy from: ARRIS ZhaoYun reserved the video output cables as shown in the following picture. This integrated design can avoid the interference to the roll rotation. 9

10 How to connect the wire for Nex5 (Only for Nex 5) How to connect the wire for Nex series (Fit for Nex series cameras) How to connect the wire for GoPro 3 10

11 8. How to connect the wire with Video TX/RX systems Connect the cable with the Video TX on top of the gimbal, then power the video TX. The camera can use the same battery as the gimbal. After you power the gimal, the camera will work. 11

12 9. How to Adjust the Parameters in Software For ARRIS Zhao Yun Pro, we have adjusted the settings and tested it according to the version of camera you choose, so we do not suggest you to change the settings. However, if you need to make some adjustment, the information below may help you. (Here we only introduce some basic parameter, for other advanced settings, you can check them on You need to install Java, which is compatible with your computer. 9.2 Install the Driver for software 9.3 Install the Software 9.4 Give power to the gimbal, connect it to the computer through USB cable. Your computer will detect the USB port, after the detection, open the software, you could see the following picture: 9.5 Choose the right port of the USB, and then click Connect. After it connect with the computer successfully, just click READ, then you could see the settings on the interface 12

13 9.6 You can adjust the settings on it now. After you change the settings, remember to click WRITE to save them. For more information about the parameters in software, you can check the simplebgc user manual. Note: A. Before you upgrade the firmware, remember to save the settings. After you upgrade it, if the settings changed, you can load the one you saved. B. If you click the USE DEFAULTS or upgrade the firmware and clear all the settings. You can load the stock settings and set it again. RC Setting If you define the Roll, Pitch, Yaw to stick, please activate the SPEED MODE. If you define the Roll, Pitch, Yaw to Knob, please activate the ANGEL MODE. How to set the stock settings? 1. Connect the gimbal with the computer, load the stock settings comes with the DVD of the gimbal to Profile 1, then click Write to save it. (If you could not find the stock settings, you can write to the customer service will send it to you) 13

14 2. Click Profile 2, load the stock settings again, and save it. Then calibrate the camera IMU and frame IMU, after this process, click write to save it. To calibrate the IMU is really important; you need to remain the sensor horizontal. 3. Return to Profile 1, choose the Follow Mode, click Follow Yaw, and then click Write to save it. 4. Disconnect the gimbal, the gimbal should be working again. 10. How to set the Follow Mode in SimpleBGC-GUI After you load the settings in GUI, click Follow Yaw, and click the Follow yaw, then click write to save is OK. Just like the picture as below: 11. How to set the Lock Mode in SimpleBGC_GUI After you set the setting well, do not choose Follow Yaw, just set it as the following picture (Then gimbal will be in Lock Mode): 14

15 12. Frequent Asked Questions After you power the gimbal, it does not work 1. You can check the connectors between the main controller and the sensor, make sure they connect well without broken. 2. The parameters in the main controller might be cleared. You need to enter set the settings again One of the motor is swinging 1. Please check whether the motor wire is connect well, there are 3 wires on the motor. If one wire broke, it may cause this problem. 2. You may not choose the right direction of the motor. This can be solved in software. Choose the swing motor, and click invert under motor configuration is OK Motor does not move 1. You can check whether the motor is stuck by the sand, screw, dust and etc When you control the pitch, the gimbal swing quickly when it reach some angle 1. Generally, the sensor wire twined, so the motor could not work properly. This will cause this problem. 15

16 12.5--High frequency vibration of the Gimbal 1. The camera is not fixed tighten enough When you control the pitch or roll, the gimbal is shaking 1. The manual control wire, video output wire or other items may block the modification position of the gimbal The image of the video is not stable 1. This may caused by the vibration of the multicopter, try to reduce the vibration of the multicopter. 2. It may cause by the soft damping balls, you can change some hard damping balls to have a try There is jelly in the video 1. This may caused by the vibration of the multicopter, try to reduce the vibration of the multicopter. 2. It may cause by the hard damping balls, you can change some soft damping balls to have a try. 13. Product Specifications 13.2 Overall Features 3-Axis modifications: pitch, roll and yaw Manual Control Angle: Pitch Angle: 360 degree Roll Angle: <45 degree Yaw Angle: 360 degree Compatible cameras: most of the micro DSLR cameras and GoPro Recommended Lens: Prime lens 13.3 Mechanical Features Working Voltage: 3S battery voltage Working Temperature: -10 to 50 Weight: 800g Dimension:190mm x 150mm x 160mm 16