Loop Powered Display Spec. Sheet

Transcription

1 Spec. Sheet Tel: (705) Web: Fax: (705) Model #DPM02 Model #DWM02 FEATURES #DXX02 Programmable Display for Meters,Feet and User Defined Units The ABM Display,Model DXM02 current loop powered display indicates the percentage full or empty of the tank whose level is being monitored by a sensor with a Ma output. The display can also be calibrated in Meters,Feet or User Defined units. The display can be changed to indicate 100% at ma or ma by simply moving an internal link. The display is packaged in a compact NEMA X enclosure which can be wall mounted or probe mounted. Specification: Display 1/2 Digit LCD 1/2 (12.7mm) High Temperature 0 to 10 F(0 to 60 C) Voltage Drop: ma Accuracy Reading +/0.5% Humidity: Range: 0 95% NonCondensing 3.5 ma to 22mA Maximum current: 150 ma Display Range: Normal 100%@ ma 3% to 112% 0%@ ma Reverse 100%@ ma 12% to +113% 0%@ ma 22mA and above LOE (Loss of Echo) Enclosure Outline: 3.53" 2.367" LOOP POWERED DILAY % 1/2 High (12.7mm) 3 Digit LCD Display 0.236".056".528" Enclosure: Nema X, IP65 Refer to Catalogue Number below for ordering Information. Catalogue #DXX02 WM wall mount PM probe mount Front View Ø0.172" Typ. of Mtg. Holes 1 10A32 R2

2 User Instruction Manual Tel: (705) Web: Fax: (705) Fig.#1) Inter Connection Diagram For D To ABM 3 Wire Level Transmitter ma ma 2V DC ma! RS232/85 A/TX 2 B/RX 1 FUSE F1/8 A 250V See Note ma See Note +V ma Gnd. + ma ma Gnd. Neut. Line STATUS CALIBRATION SWITCH ABM 3 Wire Level Transmitter Fig.#2) Inter Connection Diagram For D To ABM Wire Level Transmitter ma Note Remove jumper if other device is to be connected ACV IN ma RS232/85 A/TX 2 Fig.#3) Inter Connection Diagram For D To ABM 2 Wire Level Transmitter! L1 8 L2/N B/RX 1 F1/8 A 250V 3 STATUS CALIBRATION SWITCH FUSE ABM Line Neut. Gnd. + ma ma Wire Level Transmitter ma + Loop Voltage ma + STATUS ABM Calibration ma 2 Wire Level ma Transmitter + V max. = 28 Vdc V min. = 12 Vdc 2

3 User Instruction Manual Tel: (705) Web: Fax: (705) Fig.#1) Inter Connection Diagram For D To 3 Wire Level Transmitter ma ma +V ma. GND. See Note +V ma Gnd. 3 Wire Level Transmitter Fig.#2) Inter Connection Diagram For D To Wire Level Transmitter L Neut. GND. L N GND. Place jumper here for ma ma + ma. ma. See Note + ma ma Wire Level Transmitter Note Remove jumper if other device is to be connected Fig.#3) Inter Connection Diagram For D To 2 Wire Level Transmitter ma ma +ma. ma. + Loop Voltage ma Transmitter 3

4 Programming Manual Tel: (705) Web: Fax: (705) ECIFICATIONS PHYSICAL DILAY 1/2 DIGIT LCD Display range Normal mode ma and ma Setting: jumper J1 to Reverse mode ma and ma Setting: jumper J1 to Display mode Percentage Normal: 3% to 112% Reverse: 12% to 113% Meter Normal/Reverse: 0.00 m to m (0 to cm) 0 cm corresponds to 0% and up to cm correspond to 100% in any mode Feet Normal/Reverse: 0 ft 00 in to 199 ft 11 in. (0 to 2399 in) 0 ft corresponds to 0% and up to 2399 in. correspond to 100% in any mode User defined Normal/Reverse: 0 to in direct indication and up to in indirect indication 0 corresponds to 0% and up to correspond to 100% in any mode DILAY FORMAT INDICATION INDICATION IN PERCENTAGE Negative Percentage ( if minus is ON) or Percent Indication (Normal mode if indicator is ON) Percent Indication (Reverse mode if indicator is ON) INDICATION IN METERS Meter Indication Centimeters 0 to Meters 0 to 199 Decimal Point INDICATION IN FEET Feet Indication Inches 0 to 11 : Feet 0 to 199 Separates inch from feet USER DEFINED INDICATION Indirect Indication Multiplier: 100 No colon or Minus sign is on Range Multiplier O to Direct Indication Indirect Indication Range: 000 to Obtain value: 655 x 100 = 65500

5 Programming Manual Examples Tel: (705) Web: Readout Setup Long Press Short Press Menu Options MO Unit Indicator UI 100 Readout in measurement (longer than 1.5 S.) MO Menu options: MO Menu Editing Unit Indicator: UI Meters : Feet/Inch No sign User Defined indicator on right side of display (Percentage) MO MO S 1 P percentage E meter F feet/inch : L liter S step A max calibration value Max. height of the material I min calibration value Min. height of the material o store settings (for 100% at ma.) Step value 2 A 3 (press as many times as needed) Step value and multiply o I 5 o Step value and multiply 6 Repeat steps 1 to 6 To complete calib. values o Blinks or 25 sec Measurement Display format: Meter Foot Liter Calibration value min max default min max default min max default Boundaries: Min Max Possible values 0.01m 0.01m 1in 1in 1 1 for Step (positive 0.10m 0.10m 1ft 1ft and negative) 1.00 m 1.00m 10ft 10ft m 10.00m 100ft 100ft m m

6 Programming Manual Examples Tel: (705) Fax: (705) Web: Example 1 : From Normal Percent Display Mode (100% = Ma.) program readout in meters with : Maximum Calibration equal to 6.1 m and Minimum Calibration equal to 1.1 m. Where : Long Press is : Short Press is Meters E A (6 times) Menu Editing E 6.10 Display in Meters E Minimum Calibration I Step S 1.10 Choose Step 0.1 o Maximum Calibration A o 0.1 Blinks,Storage of calib. values in memory o or 25 sec. Minimum Calibration I Measurement in meters s 6

7 Programming Manual Examples Tel: (705) Fax: (705) Web: Example 2 : From Normal Percent Display Mode (100% = Ma.) program readout in Feet and inches with : Maximum Calibration equal to 2 Ft. 10 inches and Minimum Calibration equal to 1 Ft. 11 inches Where : Long Press is : Short Press is Default Normal Percentage Display F : A (2 times) Menu Editing F 2 Feet 10 Inches : 2.10 Display in Feet : : F : I Step : S : 1.11 Select Step 0.01 which is 1 inch 0.01 : o Maximum Calibration : A : o (10 times) : 0.10 Blinks,Storage of calib. values in memory : o or 25 sec. Minimum Calibration : I Shows 2 Feet and 1 Inch : 2.01 (11 times) : 0.11 : s 7

8 Programming Manual Examples Tel: (705) Fax: (705) Web: Example 3 : Readout is programmed in Meters go back to Normal Percent Display Mode (100% = Ma.) Where : Long Press is : Short Press is 5.90 P P Normal Percentage Display Blinks P o o o 56 or 25 sec. 8

9 Probe Mounting Equipment Technical Specifications Tel. (705) Web: Fax:(705) " 0.670" % 3.125"Ø 0.75" Model # Dimension Dimension 'A' 'B' ABM300/XX05UL 9.65" 3.0" ABM300/XX052UL 10.05" 3.05" ABM300/XX070UL 9.25" 2.25" 'A' ABM300/XX080UL 9.25" 2.25" ABM300/XX081UL 9.15" 2.1" ABM300/XX018UL 9.0" 2.0" 1.0" 'B' 9 10