G60 SERIES ELECTRONIC PRESET COUNTER ESC P1 / P2 SHIFT RESET ENT

Transcription

1 LINE SEIKI G0 SERIES ELECTRONIC P COUNTER or DIGITS ( Line LED Display) POWER SUPPLY (AC0 ~ 0V) PRESCALE FUNCTION KEY PROTECT, MEMORY DECIMAL POINT POSITIONING DUST / SPLASH PROOF G0 - G0 - MODEL SELECTION Models G0 - G0 - G0 - G0 - G0-0 G0-0 G0-0 G0-0 G0 - G0 - G0 - G0 - Figures Preset Level FRONT PANEL AND REAR TERMINALS OUT P P OUT OUT ESC P / P Level Preset G0-,, 0, 0, 0, 0 Level Preset G0-,,,,, Rear Terminals Common to all models ESC Use this button to exit from the setting mode. ( level preset only) P / P Use this button to enter and exit the setting mode for P or P from count mode. ( level preset only) Use this button to enter the setting mode from count mode. In setting mode, use this button to shift from each digit to edit or to change decimal point position. Increments the selected digit. Decrements the selected digit. Use this button to reset the count value of the counter. Use this button to save the settings made.

2 OPERATIONS In entering the setting mode to edit the preset values, prescale or decimal position, make sure that the key protect feature is disabled by unshorting terminals No. and No.. A. Setting the B. Setting the < Level Preset> Press the key to enter Preset setting mode. This will cause left most digit of the editing display to blink. Press the key to move the cursor to the next digits. While pressing the key, press the key to show setting display. While on setting display, press the key once more to enter the setting mode. This will cause the left most digit of the Multiplier display to blink. (If key is not pressed within secs. while on setting display, the display will automatically return to count mode display. Setting Display Multiplier ( ) Display Divider ( ) Display Press the key to move the cursor to the next digits Multiplier ( ) Display Divider ( ) Display When editing is finished, press the key to save the To exit from setting mode without saving, press the ESC If - (minus) sign is desired, press the key,while the key is pressed, while the left most digit of the editing display is set to "0" The - character will be displayed. To remove the - (minus) sign, press the key while the key is pressed. < Level Preset> P / P Select which preset level (P or P) to set by pressing the P /P The chosen preset level is indicated by the lighted lamp. Press the key to enter setting mode. This will cause left most digit of the editing display to blink. Press the key to move the cursor to the next digits. When editing is finished, press the key to save the To exit from setting mode without saving, press the P /P If - (minus) sign is desired, press the key,while the key is pressed, while the left most digit of the editing display is set to "0" The - character will be displayed. To remove the - (minus) sign, press the key while the key is pressed. When editing is finished, press the key to save the To exit from setting mode without saving, press the ESC Explanation for the Formula Formula C. Setting the Decimal Position = Desired Display Value (per unit) Pulse Number (per unit) <Examples>. To display count per pulses, set : Multiplier = Divider = 00. To display counts per pulse, set : Multiplier =.0000 Divider = 000 While pressing simultaneously the and keys, press the key to change the Decimal Point Position setting. Press the key successively to scroll through the different decimal point positions Multiplier Divider When the desired Decimal Point Position setting is set, release the and keys. The display will automatically changed to the chosen decimal point position setting chosen.. Changing the decimal point position while counting may cause changes in the count value and setting values of the counter. Please change settings when counter is not in operation.

3 SAMPLE OPERATIONS < LEVEL P> (P) Auto- Mode Time: 0. sec. (P) * time on auto reset mode will be 0. sec. even if set to latch Type : Sub (P) "0" "-" * Subtracts from (P) value and outputs when reaches to 0. < LEVEL P> nd preset value (P) Auto- Mode nd preset value (P) * time of the P preset level on on auto reset mode will be 0. sec. even if set to latch Type : Sub nd preset value (P) "0" "-" * Subtracts from nd preset (P) value and outputs when reaches to 0. Type : Quadrature / Time: One Shot (0.sec.) nd preset value (P) Auto- Mode Type : Quadrature / Time: One Shot (0. sec.) nd preset value (P) Auto- Mode Type : Sub nd preset value (P) * Subtracts from nd preset (P) value and outputs when reaches to 0. Then, returns to P automatically. Count Value "0"

4 WIRING Terminal Locations Level Preset Level Preset (Add / Sub) (Quad/Individual add, sub) (Add / Sub) (Quad/Individual add, sub) No. No. A No. No. DCV B DCV DCV (P) (P) N. O. Relay output (P) N. O. Relay output N. O. Relay output N. O. Relay output (P) AC 0V Power AC 0V Power AC 0V Power AC ~ V Source AC ~ V Source AC ~ V Source Supply power source AC ~ V to terminal No.,. B DCV (P) (P). N. O N. O. AC 0V AC ~ V Relay output (P) Relay output (P) Power Source Add or Sub input ( input only) G0 -,, 0 0,, Quad. / Individual add,sub. input ( input) G0 -,, 0 0,, Select from Add or Sub by setting dip-switch No.. For Add, dip-switch No. should be OFF. For Sub, dip-switch No. should be ON. * Setting of dip-switch should be done during power off. Contact, add input Switch Non - contact, add input Open Collector Transistor Contact, sub input Select from Quadrature or Individual Add/Sub by setting dip-switch No.. For Quadrature, dip-switch No. should be OFF. For Individual Add/Sub, dip-switch No. should be ON. * Setting of dip-switch should be done during power off. Switch Non - contact, sub input Open Collector Transistor Contact Non-contact 0 Quadrature Double pulse sensor B B B VDC (Internal power supply is used.) Load (External power supply is used Load (Internal power supply is used.) Load (External power supply is used Load DCV Power Supply DC ~ V - Load Load Power Supply - Relay output DCV Relay output DC ~ V t Inhibition Key protection and Protection inihibition Key protection : Pulses will not be counted while terminal nos. and are shorted. :, s, Decimal Point Position and Front Key ting will be disabled while terminal nos. and are shorted. Remote reset : ting of the counter can be done remotely while terminal nos. and are shorted by a Relay, Microswitch. Counter remains reset while and are shorted. DIP - SWITCH Sub Contact Latch Overrun Individual add, sub Contact Latch Overrun Add / Sub input ( input) ON OFF Quad. Individual add, sub input ( input) ON OFF Non-contact input Add Auto-reset One shot (0.sec) Non-contact input 0 Quadrature input Auto-reset One shot (0.sec)

5 SPECIFICATIONS Preset Level Display Models Preset Range Method Count Speed Pulse Width Make (Duty) Type Time Delay Inhibition Function Preset Lamp Operation Mode Decimal Point Position Lamp Memory for Sensor Power Consumption Operating Temperature Operating Humidity Weight (Multiplier : , Divider : - /) Non-contact input : 0 sec minimum. / Contact input : 0 msec minimum : khz : msec maximum Front reset, Remote reset (0msec min.), Auto-reset Overrun / Auto-reset E²PROM DCV 0mA maximum AC0-0V -%/% Approximately VA level digit : Red LED Count figures :.0 x.mm Editing figures :.0 x.0mm digit : Red LED Count figures :.0 x.0mm Editing figures :. x.mm digit : / digit : input type : Add / Sub input (selectable by dip-switch) input type : 0 Quadrature / Individual add, sub. input (selectable by dip-switch) Non-contact input : Open collector / Contact input : Relay, Microswitch Non-contact input : khz (with : khz max.)* / Contact input : Hz maximum Contact output : Relay Type A only (AC0V, 0.A / DC0V, A maximum Load) * for each output Non-contact output : NPN open collector (DC0V, 0mA maximum) 0. sec or latch. (However, in Auto-reset mode, output time will be 0. sec, even if set to latch) C (Non-freezing) - %RH (Non-condensing) Approximately 0g khz : 0msec maximum (with model) When the Inhibition terminals are enabled, count input, preset editing, prescale editing and front reset are disabled. None G0-,, 0, 0, 0, 0 G0-,,,,, digit : 0 / 0.0 / 0.00 digit : 0 / 0.0 / 0.00 / / Turns ON during output time level Turns on while each preset value are shown on the display. Approximately 0g * If rotary encoder is used and prescale factor is not used at the counter, maximum count speed should be khz when the phase of quadrature is 0 ± 0 and khz when that is 0 ±. If prescale factor is used at the counter, maximum count speed should be khz in any case. DIMENSION Panel cutout : - 0 x Address : Contacts : URL : * Specifications Subject to Change Without Prior Notice All Rights Reserved, Copyright 00 Line Seiki Co., Ltd A LINE SEIKI CO.,LTD. -, Chuo-Cho, -Chome, Meguro-ku Tokyo -000 JAPAN Tel: --- Fax: webtrade@line.co.jp