1/7. Field settings table [6.8.2] =... ID66F2 / ID66F3. Applicable indoor units. *GSQH10S18AA9W ThermaliaC12* Notes 4P E

Transcription

1 /7 [6.8.] =... ID66F / ID66F3 Applicable indoor units *GSQHS8AA9W ThermaliaC* Notes

2 /7 User settings Preset values Room temperature Comfort (heating) R/W [3-7]~[3-6], step: A.3..4 C Eco (heating) R/W [3-7]~[3-6], step: A C LWT main [8-9] Comfort (heating) [8-A] Eco (heating) Comfort (heating) R/W -~, step: C Eco (heating) R/W -~, step: C - C Tank temperature [6-A] Storage comfort R/W 3~[6-E] C, step: C [6-B] Storage eco R/W 3~min(,[6-E]) C, step: C [6-C] Reheat R/W 3~min(,[6-E]) C, step: C Set weather dependent Main [-] Set weather-dependent heating Low ambient temp. for LWT main zone heating R/W -4~ C, step: C [-] Set weather-dependent heating High ambient temp. for LWT main zone heating R/W ~, step: C [-] Set weather-dependent heating Leaving water value for low ambient temp. for R/W [9-]~[9-] C, step: C LWT main zone heating [-3] Set weather-dependent heating Leaving water value for high ambient temp. for R/W [9-]~min(4,[9-]) C, step: C LWT main zone heating Additional [-] Set weather-dependent heating Leaving water value for high ambient temp. for R/W [9-]~min(4,[9-6]) C, step: C LWT add zone heating [-] Set weather-dependent heating Leaving water value for low ambient temp. for R/W [9-]~[9-6] C, step: C LWT add zone heating [-] Set weather-dependent heating High ambient temp. for LWT add zone heating R/W ~, step: C [-3] Set weather-dependent heating Low ambient temp. for LWT add zone heating R/W -4~ C, step: C - Installer settings System layout Standard A... [E-] Unit type R/O ~ : Ground source A... [E-] Compressor type R/O : 6 A...3 [E-] Indoor software type R/O : Type A... [-D] BUH type R/O 4: 3PN,(/) A...6 [D-] Forced off contact : Open tariff : Closed tariff 3: Thermostat A...7 [C-7] Unit control method R/W : LWT control : Ext RT control : RT control A...8 [7-] Number of LWT zones R/W : LWT zone : LWT zones A...9 [F-D] Pump operation mode R/W : Continuous : Sample (only possible if [C-7] = ) : Request (only possible if [C-7] ) A...A [E-4] Power saving possible R/O : No A...B User interface location R/W : At unit : In room Options A...4 [C-] Contact type main R/W : Thermo ON/OFF A... [C-6] Contact type add. R/W ~ : Thermo ON/OFF A...6. [C-] Digital I/O PCB Ext. backup heat src : Bivalent : - 3: - A...6. [D-7] Digital I/O PCB Solar kit R/O : No (#) A [C-9] Digital I/O PCB Alarm output rmally open : Normally closed A...7 [D-4] Demand PCB : Pwr consmp ctrl A...8 [D-8] External kwh meter A...9 [D-9] External kwh meter A...A [D-] DHW pump : Secondary rtrn : Disinf. Shunt 3: Circul. Pump 4: CP & disinf. Sh A...B [C-8] External sensor : Outdoor sensor (##) : Room sensor Capacities A..3. [6-3] BUH: step R/W ~ kw, step:, kw A..3.3 [6-4] BUH: step R/W ~ kw, step:, kw (#) Setting is not applicable for this unit. Do not change the. *GSQHS8AA9W / ThermaliaC*

3 3/7 Space operation LWT settings Main A.3... LWT setpoint mode R/W : Fixed : Weather dep. : Fixed / scheduled 3: WD / scheduled A.3... [9-] Temperature range Minimum temp (heating) R/W ~37 C, step: C A.3... [9-] Temperature range Maximum temp (heating) R/W 37~, step: C A.3... [8-] Modulated LWT A [F-B] Shut-off valve Thermo On/OFF A [9-B] Emitter type R/W : Quick : Slow Additional A.3... LWT setpoint mode R/W : Fixed : Weather dep. : Fixed / scheduled 3: WD / scheduled A.3... [9-] Temperature range Minimum temp (heating) R/W ~37 C, step: C A.3... [9-6] Temperature range Maximum temp (heating) R/W 37~, step: C Delta T source A [9-9] Heating R/W 3~, step: C 8 C Room thermostat A.3... [3-7] Room temp. range Minimum temp (heating) R/W ~8 C, step: A.3..4 C A.3... [3-6] Room temp. range Maximum temp (heating) R/W 8~3, step: A A.3.. [-A] Room temp. offset A.3..3 [-9] Ext. room sensor offset A.3..4 Room temp. step R/W : C :, C Operation range A.3.3. [4-] Space heating OFF temp R/W 4~3 C, step: C 8 C Domestic hot water (DHW) Type A.4. [6-D] R/W : Reheat only : Reheat + sched. : Scheduled only Disinfection A.4.4. [-] Disinfection A.4.4. [-] Operation day R/W : Each day : Monday : Tuesday 3: Wednesday 4: Thursday : Friday 6: Saturday 7: Sunday A [-] Start time R/W ~3 hour, step: hour 3 hours A [-3] Temperature target R/O 6 A.4.4. [-4] Duration R/W 4~6 min, step: min 4 min Maximum setpoint A.4. [6-E] R/W 4~6, step: C 6 SP mode A.4.6 R/W : Fixed : Weather dep. Weather dependent curve A.4.7 [-B] Weather-dependent curve DHW setpoint for high ambient temp. for DHW R/W 3~[6-E] C, step: C A.4.7 [-C] Weather-dependent curve DHW setpoint for low ambient temp. for DHW R/W 4~[6-E] C, step: C 6 A.4.7 [-D] Weather-dependent curve High ambient temp. for DHW R/W ~, step: C A.4.7 [-E] Weather-dependent curve Low ambient temp. for DHW R/W -4~ C, step: C - Heat sources Backup heater A... [4-] Operation mode : Only DHW A...3 [4-7] Enable BUH step A...4 [-] Equilibrium temp. R/W -~3 C, step: C System operation Auto restart A.6. [3-] Preferential kwh rate A.6.. [D-] Allowed heaters R/O : None A.6.. [D-] Forced pump OFF R/W : Forced off : As normal Pwr consumpt. Control A.6.3. [4-8] Mode limitation : Continuous : Digital inputs A.6.3. [4-9] Type R/W : Current : Power A [-] Amp. value (#) Setting is not applicable for this unit. Do not change the. *GSQHS8AA9W / ThermaliaC*

4 4/7 A [-9] kw value A [-] Amp. limits for DI Limit DI A [-6] Amp. limits for DI Limit DI A [-7] Amp. limits for DI Limit DI3 A [-8] Amp. limits for DI Limit DI4 A [-9] kw limits for DI Limit DI A [-A] kw limits for DI Limit DI A [-B] kw limits for DI Limit DI3 A [-C] kw limits for DI Limit DI4 A [4-] Priority R/O : None : BUH Averaging time A.6.4 [-A] averaging : hours : 4 hours 3: 48 hours 4: 7 hours Ext amb. sensor offset A.6. [-B] Brine freezeup temperature A.6.9 [A-4] R/W : : - C : -4 C 3: -6 C 4: -8 C : - 6: - C 7: -4 C Emergency A.6.C R/W : Manual : Automatic Overview settings A.8 [-] Leaving water value for high ambient temp. for LWT add zone heating R/W [9-]~min(4,[9-6]) C, step: C A.8 [-] Leaving water value for low ambient temp. for LWT add zone heating R/W [9-]~[9-6] C, step: C 6 A.8 [-] High ambient temp. for LWT add zone heating R/W ~, step: C A.8 [-3] Low ambient temp. for LWT add zone heating R/W -4~ C, step: C - A.8 [-4] -- 8 A.8 [-] -- A.8 [-6] -- 3 A.8 [-7] -- A.8 [-B] Leaving water value for high ambient temp. for DHW R/W 3~[6-E] C, step: C A.8 [-C] Leaving water value for low ambient temp. for DHW R/W 4~[6-E] C, step: C 6 A.8 [-D] High ambient temp. for DHW R/W ~, step: C A.8 [-E] Low ambient temp. for DHW R/W -4~ C, step: C - A.8 [-] Low ambient temp. for LWT main zone heating R/W -4~ C, step: C - A.8 [-] High ambient temp. for LWT main zone heating R/W ~, step: C A.8 [-] Leaving water value for low ambient temp. for LWT main zone heating 6 A.8 [-3] Leaving water value for high ambient temp. for LWT main zone heating R/W [9-]~min(4,[9-]), step: C A.8 [-4] -- A.8 [-] -- A.8 [-6] -- A.8 [-7] -- 3 A.8 [-8] -- A.8 [-9] -- 8 A.8 [-A] What is the averaging time for the outdoor temp? averaging : hours : 4 hours 3: 48 hours 4: 7 hours A.8 [-] When should the disinfection function be executed? R/W : Each day : Monday : Tuesday 3: Wednesday 4: Thursday : Friday 6: Saturday 7: Sunday A.8 [-] Should the disinfection function be executed? A.8 [-] When should the disinfection function start? R/W ~3 hour, step: hour 3 hours A.8 [-3] What is the disinfection target temperature? R/O 6 A.8 [-4] How long must the tank temperature be maintained? R/W 4~6 min, step: min 4 min A.8 [-] Room antifrost temperature R/W 4~6 C, step: C C A.8 [-6] Room frost protection A.8 [-9] Adjust the offset on the measured room temperature A.8 [-A] Adjust the offset on the measured room temperature (#) Setting is not applicable for this unit. Do not change the. *GSQHS8AA9W / ThermaliaC*

5 /7 A.8 [-B] What is the required offset on the measured outdoor temp.? A.8 [3-] Is auto restart of the unit allowed? A.8 [3-] -- A.8 [3-] -- A.8 [3-3] -- 4 A.8 [3-4] -- A.8 [3-] -- A.8 [3-6] What is the maximum desired room temperature in heating? R/W 8~3, step: A A.8 [3-7] What is the mimimum desired room temperature in heating? R/W ~8 C, step: A.3..4 C A.8 [3-8] -- 3 A.8 [3-9] -- A.8 [4-] What is the BUH operation mode? : Only DHW A.8 [4-] -- A.8 [4-] Below which outdoor temperature is heating allowed? R/W 4~3 C, step: C 8 C A.8 [4-3] -- 3 A.8 [4-4] -- A.8 [4-] -- A.8 [4-6] -- (Do not change this value) / A.8 [4-7] Enable the second step of the backup heater? A.8 [4-8] Which power limitation mode is required on the system? limitation : Continuous : Digital inputs A.8 [4-9] Which power limitation type is required? R/W : Current : Power A.8 [4-A] -- A.8 [4-B] -- A.8 [4-D] -- 3 A.8 [4-E] Is the installer on site? A.8 [-] Is backup heater or boiler operation allowed above equilibrium R/W : Allowed temperature during space heating operation? : Not allowed A.8 [-] What is the equilibrium temperature for the building? R/W -~3 C, step: C A.8 [-] -- A.8 [-3] -- A.8 [-4] -- A.8 [-] What is the requested limit for DI? A.8 [-6] What is the requested limit for DI? A.8 [-7] What is the requested limit for DI3? A.8 [-8] What is the requested limit for DI4? A.8 [-9] What is the requested limit for DI? A.8 [-A] What is the requested limit for DI? A.8 [-B] What is the requested limit for DI3? A.8 [-C] What is the requested limit for DI4? A.8 [-D] What type of backup heater installation is used? R/O 4: 3PN,(/) A.8 [-E] -- A.8 [6-] The temperature difference determining the heat pump ON temperature. R/W ~, step: C 4 C A.8 [6-] The temperature difference determining the heat pump OFF temperature. R/W ~, step: C C A.8 [6-] -- A.8 [6-3] What is the capacity of the backup heater step? R/W ~ kw, step:, kw A.8 [6-4] What is the capacity of the backup heater step? R/W ~ kw, step:,kw A.8 [6-] -- A.8 [6-6] -- A.8 [6-7] -- A.8 [6-8] What is the hysteresis to be used in reheat mode? R/W ~, step: C A.8 [6-9] -- A.8 [6-A] What is the desired comfort storage temperature? R/W 3~[6-E] C, step: C A.8 [6-B] What is the desired eco storage temperature? R/W 3~min(,[6-E]) C, step: C A.8 [6-C] What is the desired reheat temperature? R/W 3~min(, [6-E]) C, step: C A.8 [6-D] What is the desired DHW production type? R/W : Reheat only : Reheat + sched. : Scheduled only A.8 [6-E] What is the maximum temperature setpoint? R/W 4~6, step: C 6 A.8 [7-] -- A.8 [7-] -- A.8 [7-] How many leaving water temperature zones are there? R/W : LWT zone : LWT zones A.8 [7-3] PE factor R/W ~6, step:,, A.8 [7-4] -- A.8 [7-] -- A.8 [8-] -- A.8 [8-] Maximum running time for domestic hot water operation. R/W ~9 min, step: min 3 min A.8 [8-] Anti-recycling time. R/W ~ hour, step:, hour, hour A.8 [8-3] -- A.8 [8-4] Additional running time for the maximum running time. R/W ~9 min, step: min 9 min (#) Setting is not applicable for this unit. Do not change the. *GSQHS8AA9W / ThermaliaC*

6 6/7 A.8 [8-] Allow modulation of the LWT to control the room temp? A.8 [8-6] Leaving water temperature maximum modulation. R/W ~, step: C 3 C A.8 [8-7] -- 8 A.8 [8-8] -- A.8 [8-9] What is the desired comfort main LWT in heating? A.8 [8-A] What is the desired eco main LWT in heating? A.8 [8-B] -- 3 A.8 [8-C] -- A.8 [8-D] -- 6 A.8 [9-] What is the maximum desired LWT for main zone in heating? R/W 37~, step: C A.8 [9-] What is the mimimum desired LWT for main zone in heating? R/W ~37 C, step: C A.8 [9-] -- A.8 [9-3] -- A.8 [9-4] Leaving water temperature overshoot temperature. R/W ~4 C, step: C 3 C A.8 [9-] What is the mimimum desired LWT for add. zone in heating? R/W ~37 C, step: C A.8 [9-6] What is the maximum desired LWT for add. zone in heating? R/W 37~, step: C A.8 [9-7] -- A.8 [9-8] -- A.8 [9-9] What is the desired delta T in heating? R/W 3~, step: C 8 C A.8 [9-A] -- A.8 [9-B] What emitter type is connected to the main LWT zone? R/W : Quick : Slow A.8 [9-C] Room temperature hysteresis. R/W ~6 C, step:, C C A.8 [9-D] Pump speed limitation R/W ~8,step: 6 A.8 [9-E] -- ~8,step: 6 A.8 [A-] -- A.8 [A-] -- A.8 [A-] -- A.8 [A-3] Maximum heating frequency R/W : 48Hz : 93Hz A.8 [A-4] What is the brine anti freeze up temperature? R/W : : - C : -4 C 3: -6 C 4: -8 C : - 6: - C 7: -4 C A.8 [B-] -- A.8 [B-] -- A.8 [B-] -- A.8 [B-3] -- A.8 [B-4] -- A.8 [C-] -- A.8 [C-] -- A.8 [C-] Is an external backup heat source connected? : Bivalent : - 3: - A.8 [C-3] Bivalent activation temperature. R/W -~, step: C A.8 [C-4] Bivalent hysteresis temperature. R/W ~, step: C 3 C A.8 [C-] What is the thermo request contact type for the main zone? R/W : Thermo ON/OFF A.8 [C-6] What is the thermo request contact type for the add. zone? R/W : - : Thermo ON/OFF A.8 [C-7] What is the unit control method in space operation? R/W : LWT control : Ext RT control : RT control A.8 [C-8] Which type of external sensor is installed? : Outdoor sensor (##) : Room sensor A.8 [C-9] What is the required alarm output contact type? rmally open : Normally closed A.8 [C-A] -- A.8 [C-C] -- A.8 [C-D] -- A.8 [C-E] -- A.8 [D-] Which heaters are permitted if prefer. kwh rate PS is cut? R/O : None A.8 [D-] Forced off contact type : Open tariff : Closed tariff 3: Thermostat A.8 [D-] Which type of DHW pump is installed? : Secondary rtrn : Disinf. Shunt 3: Circul. Pump 4: CP & disinf. Sh A.8 [D-3] Leaving water temperature compensation around., shift C (from - to C) : Enabled, shift 4 C (from - to C) 3: Enabled, shift C (from -4 to 4 C) 4: Enabled, shift 4 C (from -4 to 4 C) A.8 [D-4] Is a demand PCB connected? : Pwr consmp ctrl A.8 [D-] Is the pump allowed to run if prefer. kwh rate PS is cut? R/W : Forced off : As normal A.8 [D-7] Is a solar kit connected? R/O : No (#) (#) Setting is not applicable for this unit. Do not change the. *GSQHS8AA9W / ThermaliaC*

7 7/7 A.8 [D-8] Is an external kwh meter used for power measurement? A.8 [D-9] Is an external kwh meter used for power measurement? A.8 [D-A] -- A.8 [D-B] -- A.8 [D-C] -- A.8 [D-D] -- A.8 [D-E] -- A.8 [E-] Which type of unit is installed? R/O ~ : Ground source A.8 [E-] Which type of compressor is installed? R/O : 6 A.8 [E-] What is the indoor unit software type? R/O : Type A.8 [E-3] -- A.8 [E-4] Is the power saving function available on the outdoor unit? R/O : No A.8 [E-] -- A.8 [E-6] -- A.8 [E-7] -- A.8 [E-8] -- A.8 [E-9] -- A.8 [E-A] -- A.8 [E-C] -- A.8 [E-D] -- A.8 [F-] Pump operation allowed outside range. A.8 [F-] -- A.8 [F-] -- 3 A.8 [F-3] -- A.8 [F-4] -- A.8 [F-] -- A.8 [F-6] -- A.8 [F-9] Pump operation during flow abnormality. A.8 [F-A] -- A.8 [F-B] Close shut-off valve during thermo OFF? A.8 [F-C] -- A.8 [F-D] What is the pump operation mode? R/W : Continuous : Sample (only possible if [C-7] = ) : Request (only possible if [C-7] ) (#) Setting is not applicable for this unit. Do not change the. *GSQHS8AA9W / ThermaliaC*