Programmable(5+1+1)Touch Screen LCD Wired Thermostat. General. Features. Operating Algorithm

Transcription

1 Programmable(5+1+1)Touch Screen LCD Wired Thermoat General Front View Back View HTW series ermoat is widely used in ese environment like Homes, Residential buildings, Schools, Offices and etc. to main a ideal room temperature purpose. It can be used bo in Heating or Cooling syems, typically could be integrated wi e following equipments: Thermal Valves or Zone Valves Combi Boilers Gas or Oil Burners Fans Pumps Features Up to 5 operating modes configurable: Manual Mode, Automatic(5+1+1 Programmable, 6 Time Zones), Comfort, Energy Saving, and Fro Protection Big Size of LCD Display: 80x55.8mm(3.15x2.20 ) Safe Operating Voltage Protection: Controlling Panel: 2xAA batteries-powered Receiver: Line Voltage powered Operating Algorim T SD W L1 Room Thermoat Switching differential (1K) Room temperature setpoint Output Signal for Heating Version

2 Specification Casing Material LCD Backlight Power Supply Current Load Programmable(5+1+1)Touch Screen LCD Wired Thermoat ABS & Acrylic 80x55.8mm(3.15x2.20 ) Controlling Panel: 3V DC(2 x AA1.5 V) Switch: Line Voltage(110/220Vac +/- 10%, 50/60Hz) 10A (Resiive) Ambient Temp. Range 0~99.5 Set-point Range 5~45 /41 ~113 (Comfort Mode) 5~45 /41 ~113 (Energy Saving Mode) 5 ~15 /41 ~59 (Fro Protection) Accuracy/Tolerance +/-0.5 Timing Tolerance <1% NTC Thermior 10KΩ@25 Storage Conditions Temperature -10~60 Humidity Battery Life < 90% r.h. 12 mons RF Module Semi-duplex Module Setting Data Back-Up Tips: Set-points and oer parameters is able to be retained when batteries are replaced, except Time setting(if replacing batteries quickly, time setting retained as well). Please check and reset e time if got lo. Display Icons and Buttons Display Controlling Panel Display 1 Week day: from Monday to Sunday 6 Time of day(00:00..23:59) 11 Energy Saving Mode 2 Number of Programmable Time Zone 7 Heating is on 12 Fro Protection Mode 3 Room Temperature 8 Comfort Mode 4 Buttons Lock 9 Manual Mode 5 Battery Consumption Indication 10 Programmable Mode 13 Setpoint, or Floor Temperature Remarks: Version

3 1PPPPPP 1PPPPPP 1PPPPPP Programmable(5+1+1)Touch Screen LCD Wired Thermoat 1) During setting, ose displays can be set when ey are flickering. 2) When e beginning time is flickering, it is able to be set (10 mins each ep)via scrolling buttons 3) The time setting is e beginning of current time zone, also e end time of la time zone. 4) When e setpoint is flickering, it is able to be set via scrolling buttons Buttons Operation 14.Modes selecting or Time setting,etc. Modes:Selecting Automatic Mode, Comfort Mode, Energy Saving Mode and Fro Protection Mode Time Setting Press and hold is button for 3 sec, increase or decrease value by buttons; sequence from Hour, Minute to Week day via pressing button. 15. Temperature up, or oer parameters setting In case of internal and external sensors are selected, press + button for 3 sec, Setpoint is displaying external sensor s temperature; after 3 sec, it returns to setpoint Programmable setting Press button and program setpoints and time zones accordingly.increase Mon to Fri setting, 1PPPPPP setting...6pppppp setting, 6PPPPPP setting Saturday setting, 1PPPPPP setting...6pppppp setting, 6PPPPPP setting Sunday setting, 1PPPPPP setting...6pppppp setting, 6PPPPPP setting Decreasing or Increasing value by 10 mins by buttons. Ex-factory Settings Weekday Time Zone 1~5 Mon~Fri Remarks: 1.During setting, ose displays can be set when ey are flickering. 2.When e beginning time is flickering, it is able to be set (10 mins each ep)via scrolling buttons 3.The time setting is e beginning of current time zone, also e end time of la time zone.. 3) When e setpoint is flickering, it is able to be set via scrolling buttons Example: As ex-factory setting, press PRG button for 3 sec and enter into programmable setting;, from Mon to Fri display on e left top of LCD; e time is flickering, and e beginning time for 1 time zone we should enter is 00:00( also it is ending time of 6 time zone); Then press PRG again, to set 19 by scrolling buttons. Press PRG again, to set e beginning time for 2PP nd PP time zone at 06:00(also it is e ending time for 1PP PP time zone); en press PRG again to set 20 by scrolling buttons.. Press PRG again and follow e same eps to set time zones from 3 rd to 6 time, 22:45 is e beginning time of 6 time zone, also e ending time of 5 time zone. After 6 time zones for Mon to Fri are done, keep pressing PRG again and move to Sat. to set data by same eps; press PRG again and move to Sun. to set data by same eps. 6 Sat. 7 Sun. 1 06:00~08: :00~11: :30~13: :30~17: :00~22: :00~06: Version

4 Programmable(5+1+1)Touch Screen LCD Wired Thermoat After all settings are done, please press PRG or wait for 5 seconds to confirm settings. 17.Temperature down, or oer parameters setting 18.On/off button Parameter Setting HTW Under switch off atus, please press and hold button for 3 seconds Code Parameters Operated by + / - button 1 Temp Calibration -5 ~+5 2 Sensors 3 Buttons Lock/unlock 4 1 Fro Projection activation 0:Single Internal Sensor activate 1:Internal and External sensors activate 2: Single External Sensor activate 0:Except On/off button, oer buttons are locked 1:All buttons are locked (To unlock by pressing e buttons of simultaneously 0:Off 1:On 1 UU 5 1 Setpoint Range of Fro Protection 6 1 Setpoint Range of Overheating Protection Switch OFF Temperature 7 1 Differential range between room temperature and setpoint parameters are defaulted. 5 ~15 (When it is activated,if room temperature is lower an is setpoint, heating equipments will open up automatically. 35 ~70 (When room temperature is higher an is setpoint, heating equipments will be cut off automatically. 0 ~9.0.5 is defaulted. when e room temperature is higher an temperature of setpoint plus is deferential setpoint, heating equipment is cut off automatically. Switch ON Temperature 0 ~9 0.5 is defaulted. 8 1 Differential range between when e room temperature is lower an temperature of room temperature and setpoint minus is deferential setpoint, heating equipment is setpoint activated automatically. UUURemark: Those parameters can be set under Manual Mode and Automatic Programmable Mode. In oer modes, Buttons Lock/unlock Push and hold + and - buttons simultaneously for 5 sec to LOCK all buttons(including ON/OFF button) Push and hold + and - buttons simultaneously for 5 sec to UNLOCK all buttons Error Code If ere are any errors happened, error code will be displayed Er1 Internal Sensor Er3 External Sensor It might occur at some or all of em happen at a once. Please figure out by values. Examples: Er4 = Er1 + Er3-4 - Version

5 Programmable(5+1+1)Touch Screen LCD Wired Thermoat Wiring Diagram WARNING: RISK OF ELECTRICAL SHOCK. Disconnect power supply before making electrical connection. Contact wi components carrying hazardous voltage can cause electrical shock and may result in severe personal injury or dea. Frame/LCD Color and Dimensions Housing: white is defaulted, cuomized colors can be negotiated LCD Display: White is defaulted, Blue and Green colors are available Mounting HTW mm(L)*94mm(W)*18.5mm(H) Mount e room temperature controller in location where e air temperature can be measured as accurately as possible wiout adversely affect by direct solar radiation or oer source of heating or cooling Version

6 Programmable(5+1+1)Touch Screen LCD Wired Thermoat The Room Controller is wi fold-out and, which is can be used to removable device.please refer to two pictures at right side. Wall-mounting The baseplate is for universal mounting.it means it can be mounted on flat wall or mounting boxes. And below are e eps 1 Take off e baseplate from controller 2 nd Fix e baseplate using screwdriver on wall 3 rd Load e batteries 4 Insert and clip e display unit on baseplate. PPPP PP P PPPP P PP PPP P 1 ep Fold-up Stand PP PPPP P PPP PP 2 nd ep 3 rd ep PPP PPP PP PPP P 4 ep PP PPP P Battery Replacement If e battery symbol appears, e batteries are almo exhaued and mu be replaced Warranty We offer warranty of 12 mon, from e sales date. If it is not e quality problems, or beyond e warranty period, we will charge for e after-sales services -6- Version