Australian Standard. General requirements for the competence of testing and calibration laboratories AS ISO/IEC ISO/IEC 17025:1999
|
|
- Angelina Gray
- 6 years ago
- Views:
Transcription
1 AS ISO/IEC ISO/IEC 17025:1999 AS ISO/IEC Australian Standard General requirements for the competence of testing and calibration laboratories This is a free 7 page sample. Access the full version online.
2 This Australian Standard was prepared by Committee QR/10, Conformity Assessment. It was approved on behalf of the Council of Standards Australia on 21 December 1999 and published on 21 December The following interests are represented on Committee QR/10: Australian Chamber of Manufacturers Australian Quarantine and Inspection Service (Commonwealth) Consumer Electronics Suppliers Association Consumers Federation of Australia Joint Accreditation System of Australia and New Zealand NATA (Australia) Third-party certification bodies This is a free 7 page sample. Access the full version online. Keeping Standards up-to-date Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about Standards can be found by visiting the Standards Australia web site at and looking up the relevant Standard in the on-line catalogue. Alternatively, the printed Catalogue provides information current at 1 January each year, and the monthly magazine, The Australian Standard, has a full listing of revisions and amendments published each month. We also welcome suggestions for the improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via at mail@standards.com.au, or write to the Chief Executive, Standards Australia International Ltd, PO Box 1055, Strathfield, NSW This Standard was issued in draft form for comment as DR
3 AS ISO/IEC Australian Standard General requirements for the competence of testing and calibration laboratories First pubished as HB Revised and undesignated as AS ISO/IEC This is a free 7 page sample. Access the full version online. COPYRIGHT Standards Australia International All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. Published by Standards Australia International Ltd PO Box 1055, Strathfield, NSW 2135, Australia ISBN
4 ii PREFACE This Standard was prepared by the Standards Australia Committee QR/10, Conformity Assessment to supersede HB , Guidelines for third-party certification and accreditation Guide 25 General requirements for the competence of calibration and testing laboratories. It is identical with, and has been reproduced from ISO/IEC 17025:1999 which was prepared by the ISO Committee on Conformity Assessment (CASCO) to replace ISO/IEC Guide 25:1990. As this Standard is reproduced from an international Standard, the following applies: (a) (b) (c) Its number does not appear on each page of text and its identity is shown only on the cover and title page. In the source text this International Standard should read this Australian Standard. A full point substitutes for a comma when referring to a decimal marker. NOTE: Where this Standard makes reference to ISO 9001:1994, Quality systems Model quality assurance in production, installation and servicing; and ISO 9002:1994, Quality systems Model for quality assurance in production, installation and servicing, readers need to be aware that the documents referred to are the 1994 editions, currently available in Australia as AS/NZS ISO 9001:1994 and AS/NZS ISO 9002:1994 respectively. At the time of publication, ISO is in the process of revising the ISO 9000 family of Standards and it is intended that they will be published late in This is a free 7 page sample. Access the full version online.
5 This is a free 7 page sample. Access the full version online.
6 This is a free 7 page sample. Access the full version online.
7 This is a free 7 page sample. Access the full version online.
8 This is a free 7 page sample. Access the full version online. The remainder of this document is available for purchase online at SAI Global also carries a wide range of publications from a wide variety of Standards Publishers: Click on the logos to search the database online.
AS/NZS ISO/IEC 17067:2015
Australian/New Zealand Standard AS/NZS ISO/IEC 17067:2015 (ISO/IEC 17067:2013, IDT) Conformity assessment Fundamentals of product certification and guidelines for product certification schemes AS/NZS ISO/IEC
More informationAustralian Standard. Information and documentation Records management processes Metadata for records. Part 1: Principles
AS ISO 23081.1 2006 ISO 23081-1:2006 AS ISO 23081.1 2006 Australian Standard Information and documentation Records management processes Metadata for records Part 1: Principles This Australian Standard
More informationAustralian Standard. Records Management. Part 1: General AS ISO ISO
AS ISO 15489.1 2002 ISO 15489-1 AS ISO 15489.1 Australian Standard Records Management Part 1: General [ISO title: Information and documentation Records management Part 1: General] This Australian Standard
More informationAustralian Standard. Industrial automation systems and integration Open systems application integration framework
AS ISO 15745.2 2004 ISO 15745-2:2003 AS ISO 15745.2 Australian Standard Industrial automation systems and integration Open systems application integration framework Part 2: Reference description for ISO
More informationAS/NZS ISO/IEC 25030:2013
ISO/IEC 25030:2007, IDT Australian/New Zealand Standard Software engineering Software product Quality Requirements and Evaluation (SQuaRE) Quality requirements AS/NZS ISO/IEC 25030:2013 This Joint Australian/New
More informationAustralian/New Zealand Standard
AS/NZS ISO/IEC 15910:2004 ISO/IEC 15910:1999 AS/NZS ISO/IEC 15910 Australian/New Zealand Standard Information technology Software user documentation process AS/NZS ISO/IEC 15910:2004 This Joint Australian/New
More informationAustralian Standard. Records Management. Part 2: Guidelines AS ISO ISO TR
AS ISO 15489.2 2002 ISO TR 15489-2 AS ISO 15489.2 Australian Standard Records Management Part 2: Guidelines [ISO title: Information and documentation Records management Part 2: Guidelines] This Australian
More informationMiscellaneous Publication
Miscellaneous Publication Australian/New Zealand Certification Scheme for explosion-protected electrical equipment (ANZEx Scheme) Part 1: Product Certification Program Basic rules and procedures This Joint
More informationAustralian Standard. Industrial automation systems and integration Open systems application integration framework
AS ISO 15745.4 2004 ISO 15745-4:2003 AS ISO 15745.4 Australian Standard Industrial automation systems and integration Open systems application integration framework Part 4: Reference description for Ethernet-based
More informationAustralian/New Zealand Standard
AS/NZS ISO/IEC 18028.4:2006 ISO/IEC 18028-4:2005 AS/NZS ISO/IEC 18028.4:2006 Australian/New Zealand Standard Information technology Security techniques IT network security Part 4: Securing remote access
More informationAustralian/New Zealand Standard
AS/NZS ISO/IEC 27005:2012 Australian/New Zealand Standard Information technology Security techniques Information security risk management (ISO/IEC 27005:2011, MOD) This Joint Australian/New Zealand Standard
More informationAS/NZS ISO 19157:2015
AS/NZS ISO 19157:2015 (ISO 19157:2013, IDT) Australian/New Zealand Standard Geographic information Data quality Superseding AS/NZS ISO 19113:2004, AS/NZS ISO 19114:2005, and AS/NZS ISO 19138:2008 AS/NZS
More informationAustralian/New Zealand Standard
AS/NZS ISO/IEC 13235.3:2006 ISO/IEC 13235-3:1998 AS/NZS ISO/IEC 13235.3:2006 Australian/New Zealand Standard Information technology Open Distributed Processing Trading function Part 3: Provision of Trading
More informationAustralian/New Zealand Standard
AS/NZS 4366:1996 ISO/IEC 12119:1994 Australian/New Zealand Standard Information technologysoftware packagesquality requirements and testing AS/NZS 4366:1996 This Joint Australian/New Zealand Standard was
More informationAS/NZS ISO/IEC/IEEE 42010:2013
ISO/IEC/IEEE 42010:2011, IDT Australian/New Zealand Standard Systems and software engineering Architecture description AS/NZS ISO/IEC/IEEE 42010:2013 This Joint Australian/New Zealand Standard was prepared
More informationA S ISO Records Management Part 1: General
AS ISO 15489.1 2002 ISO 15489-1 AS ISO 15489.1 Australian Standard Records Management Part 1: General [ISO title: Information and documentation Records management Part 1: General] This Australian Standard
More informationAustralian/New Zealand Standard
AS/NZS 14644.3:2009 AS/NZS 14644.3:2009 Australian/New Zealand Standard Cleanrooms and associated controlled environments Part 3: Test methods (ISO 14644-3:2005, MOD) AS/NZS 14644.3:2009 This Joint Australian/New
More informationCORPORATE GOVERNANCE OF INFORMATION & COMMUNICATION TECHNOLOGY
AS 8015 2005 CORPORATE GOVERNANCE OF INFORMATION & COMMUNICATION TECHNOLOGY This Australian Standard was prepared by Committee IT-030, IT Governance. It was approved on behalf of the Council of Standards
More informationAS/NZS ISO/IEC/IEEE :2015
(ISO/IEC/IEEE 29119-1:2013, IDT) Australian/New Zealand Standard Software and systems engineering Software testing Part 1: Concepts and definitions AS/NZS ISO/IEC/IEEE 29119.1:2015 This joint Australian/New
More informationGuide 28 General rules for a model third-party certification system for products
SAA HB18.28 1991 SANZ HB18.28 1991 ISO/IEC Guide 28 1982 Guidelines for third-party certification and accreditation Guide 28 General rules for a model third-party certification system for products STANDARDS
More informationInformation and documentation Records management. Part 1: Concepts and principles AS ISO :2017 ISO :2016
ISO 15489-1:2016 AS ISO 15489.1:2017 Information and documentation Records management Part 1: Concepts and principles This Australian Standard was prepared by Committee IT-021, Records and Document Management
More informationAS/NZS ISO 13008:2014
(ISO 13008:2012, IDT) Australian/New Zealand Standard Information and documentation Digital records conversion and migration process AS/NZS ISO 13008:2014 This joint Australian/New Zealand standard was
More informationSA/SNZ TR ISO/IEC :2014
(ISO/IEC TR 20000-5:2013, IDT) Australian/New Zealand Technical Report Information technology Service management Part 5: Exemplar implementation plan for ISO/IEC 20000-1 SA/SNZ TR ISO/IEC 20000.5:2014
More informationHB Communications Cabling Manual Module 1: Australian regulatory arrangements
HB 243 2007 Communications Cabling Manual Module 1: Australian regulatory arrangements HB HB 243 2007 Handbook Communications Cabling Manual Module 1: Australian regulatory arrangements Originated as HB
More informationSA/SNZ TR :2016
SA/SNZ TR 61439.0:2016 (IEC TR 61439-0, Ed. 2.0:2013, MOD) Technical Report Low-voltage switchgear and controlgear assemblies Part 0: Guide to specifying assemblies SA/SNZ TR 61439.0:2016 SA/SNZ TR 61439.0:2016
More informationISO/IEC INTERNATIONAL STANDARD. General requirements for the competence of testing and calibration laboratories
INTERNATIONAL STANDARD ISO/IEC 17025 Second edition 2005-05-15 General requirements for the competence of testing and calibration laboratories Exigences générales concernant la compétence des laboratoires
More informationThis is a free 10 page sample. Access the full version online.
Module 1 Australian regulatory arrangements COPYRIGHT Standards Australia/Standards New Zealand All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic
More informationISO/IEC INTERNATIONAL STANDARD. Conformity assessment Supplier's declaration of conformity Part 1: General requirements
INTERNATIONAL STANDARD ISO/IEC 17050-1 First edition 2004-10-01 Conformity assessment Supplier's declaration of conformity Part 1: General requirements Évaluation de la conformité Déclaration de conformité
More informationBetter Regulatory Outcomes & the CASCO Toolbox
2011/SOM1/SCSC/CON1/013 Session 8 Better Regulatory Outcomes & the CASCO Toolbox Submitted by: Underwriters Laboratories 6 th Conference on Good Regulatory Practice Washington, D.C., United States 1-2
More informationAS/NZS 3080:2003 AS/NZS
AS/NZS 3080:2013 (ISO/IEC 11801:2011, MOD) Incorporating Amendment No. 1 Australian/New Zealand Standard Information technology Generic cabling for customer premises Superseding AS/NZS 3080:2003 AS/NZS
More informationAustralian Standard. Information technology Communication interface connectors used in local area networks AS ISO/IEC/TR 9578:1990
AS 4028 1992 ISO/IEC/TR 9578:1990 Australian Standard Information technology Communication interface connectors used in local area networks This Australian Standard was prepared by Committee IT/1, Information
More informationISO/IEC INTERNATIONAL STANDARD. Conformity assessment Requirements for bodies certifying products, processes and services
INTERNATIONAL STANDARD ISO/IEC 17065 First edition 2012-09-15 Conformity assessment Requirements for bodies certifying products, processes and services Évaluation de la conformité Exigences pour les organismes
More informationISO/IEC Conformity assessment Fundamentals of product certification and guidelines for product certification schemes
INTERNATIONAL STANDARD ISO/IEC 17067 First edition 2013-08-01 Conformity assessment Fundamentals of product certification and guidelines for product certification schemes Évaluation de la conformité Éléments
More informationISO/IEC INTERNATIONAL STANDARD. Conformity assessment Supplier's declaration of conformity Part 1: General requirements
INTERNATIONAL STANDARD ISO/IEC 17050-1 First edition 2004-10-01 Corrected version 2007-06-15 Conformity assessment Supplier's declaration of conformity Part 1: General requirements Évaluation de la conformité
More informationTelecommunications Equipment Certification Scheme FEBRUARY 2017
Telecommunications Equipment Certification Scheme FEBRUARY 2017 Canberra Red Building Benjamin Offices Chan Street Belconnen ACT PO Box 78 Belconnen ACT 2616 T +61 2 6219 5555 F +61 2 6219 5353 Melbourne
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60874-14-9 QC 910004XX0009 First edition 1999-09 Connectors for optical fibres and cables Part 14-9: Fibre optic connector type SC-APC tuned 8 terminated on single mode fibre
More informationISO/IEC TS Conformity assessment Guidelines for determining the duration of management system certification audits
TECHNICAL SPECIFICATION ISO/IEC TS 17023 First edition 2013-08-01 Conformity assessment Guidelines for determining the duration of management system certification audits Évaluation de la conformité Lignes
More informationLaboratory Accreditation Building Confidence on Testing Quality
Laboratory Accreditation Building Confidence on Testing Quality Dr. George Anastasopoulos, Director (Conformity Assessment) & Prasanth S Ramakrishnan, MS, LEED-AP (Principal Staff & Program Manager) ASME
More informationThe Progress of Proficiency Testing Accreditation
2014/SCSC/WKSP2/019 Session: 8.2 The Progress of Proficiency Testing Accreditation Submitted by: Australia Food Safety Cooperation Forum Partnership Training Institute Network Proficiency Testing Workshop
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 MICROSOFT EMC LABORATORY 1 17760 NE 67 th Court Redmond, WA 98052 Sajay Jose Email: sajose@microsoft.com Phone: 425 421 9799 ELECTRICAL (EMC) Valid to: August
More informationKENYA ACCREDITATION SERVICE
KENAS-POL-004 02 06/08/2018 06/09/2018 POL 1 of 5 Approval and Authorisation Completion of the following signature blocks signifies the review and approval of this Document. Authored by ASSISTANT DIRECTOR
More informationELECTRICAL PRODUCT CERTIFICATION SERVICES. Australia & New Zealand CLIENT GUIDELINES
ELECTRICAL PRODUCT CERTIFICATION SERVICES Australia & New Zealand CLIENT GUIDELINES PREFACE During the hustle and bustle of life, how many of us think twice about the intrinsic safety of the humble drill,
More informationPlumbing Product Certification WaterMark Level 2
NCSI Recognition Booklet Addendum Plumbing Product Certification WaterMark Level 2 1. General In Australia most of the plumbing and drainage products and materials are required to be certified under the
More informationConformity Assessment Schemes and Interoperability Testing (1) Keith Mainwaring ITU Telecommunication Standardization Bureau (TSB) Consultant
Conformity Assessment Schemes and Interoperability Testing (1) Keith Mainwaring ITU Standardization Bureau (TSB) Consultant Moscow, 9-11 november 2011 Contents The benefits of conformity assessment Conformity
More informationInformation technology Process assessment Concepts and terminology
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO/IEC 33001 Second edition 2015-03-01 Information technology Process assessment Concepts and terminology Technologies de l information Évaluation
More informationMYOB Beginners Course
MYOB Beginners Course using MYOB Accounting v18 Preface This workbook has been written to cover the entry of Cash Book, Accounts Receivable and Accounts Payable transactions using MYOB Accounting, [Plus,
More informationISO Certification For Laboratory Accreditation. Dr Amadou TALL Consultation
ISO 17025 Certification For Laboratory Accreditation Dr Amadou TALL Consultation ISO 17025 Certification ISO/IEC 17025 Global quality standard for testing and calibration laboratories. It is the basis
More informationAsureQuality Limited. CodeMark Programme. Certificate Holder Responsibilities and Requirements
AsureQuality Limited CodeMark Programme Certificate Holder Responsibilities and Requirements Page 1 of 6 1. SCOPE This document describes the responsibilities and requirements of Certificate Holders for
More informationInternational Laboratory Accreditation Cooperation. The ILAC Mutual Recognition Arrangement. global trust. Testing Calibration Inspection
International Laboratory Accreditation Cooperation The ILAC Mutual Recognition Arrangement Enhancing the acceptance of products and services across national borders Removing barriers to global trade Accreditation
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. LAIRD TECHNOLOGIES, INC. W66 N220 Commerce Court Cedarburg, WI Adam Alger Phone:
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 LAIRD TECHNOLOGIES, INC. W66 N220 Commerce Court Cedarburg, WI 53012 Adam Alger Phone: 262 375 4400 ELECTRICAL (EMC) Valid to: January 31, 2019 Certificate
More informationGlobal-Mark P/L. Management Document G-77 Title: Product conformance CodeMark program Type: Program Information Brochure. This document is external
Global-Mark P/L Management Document G-77 Title: Product conformance CodeMark program Type: Program Information Brochure This document is external Document Information and Revision History Document Number
More informationCERTIFICATION CONDITIONS
1 of 5 + CERTIFICATION CONDITIONS PERMIT NO 000/0. SATAS SOUTH AFRICAN TECHNICAL AUDITING SERVICES Pty Ltd Co Reg No 2002/015355/07 AGREEMENT ENTERED INTO WITH Co Reg No.. 2 of 5 CERTIFICATION CONDITIONS
More informationS. Scholz / K. Meyer / J.E. Nielsen / Harald Drück/J.Fernández/E.Prado/L.Nelson Page 1 of 7
Global Solar Certification Network Working Rules Annex A. Requirements for Certification Bodies and their subcontracted laboratories, inspection bodies and inspectors Date: 2017/03/07 Document number:
More informationPEFC N 04 Requirements for certification bodies and accreditation bodies
PEFC N 04 Requirements for certification and accreditation Organisation Articles of Association for PEFC Norway Forest certification PEFC N 01 Norwegian PEFC certification system for sustainable forestry
More informationUSDA ISO Guide 65 Program Accreditation for Certification Bodies
Page 1 of 6 USDA ISO Guide 65 Program Accreditation for Certification Bodies 1 Purpose This document provides the requirements to be met in designing a USDA ISO Guide 65 Program. It also provides the requirements
More informationILAC-R7:09/2009. Rules for the Use of the ILAC MRA Mark
Rules for the Use of the ILAC MRA Mark Copyright ILAC 2009 ILAC encourages the authorized reproduction of this publication, or parts thereof, by organisations wishing to use such material for areas related
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8655-2 First edition 2002-09-15 Piston-operated volumetric apparatus Part 2: Piston pipettes Appareils volumétriques à piston Partie 2: Pipettes à piston Reference number ISO
More informationInstruction. Rules for Use of Logo
Page 1/7 Purpose: The purpose of this instructions to provide the requirements for the use of Accreditation and certification Mark/Logo to the certified Client organization. General Accreditation mark
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO/IEC 90003 First edition 2004-02-15 Software engineering Guidelines for the application of ISO 9001:2000 to computer software Ingénierie du logiciel Lignes directrices pour l'application
More informationMedical devices Quality management Medical device nomenclature data structure
INTERNATIONAL STANDARD ISO 15225 Third edition 2016-03-15 Medical devices Quality management Medical device nomenclature data structure Dispositifs médicaux Management de la qualité Structure des données
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-34280-7 ISO 9004:2009 SOUTH AFRICAN NATIONAL STANDARD Managing for the sustained success of an organization A quality management approach This national standard is the identical implementation
More informationGUIDE 75. Strategic principles for future IEC and ISO standardization in industrial automation. First edition
GUIDE 75 First edition 2006-11 Strategic principles for future IEC and ISO standardization in industrial automation Reference number ISO/IEC GUIDE 75:2006(E) GUIDE 75 First edition 2006-11 Strategic principles
More informationWorkshop Item 1 - ISO 9001: 2008 migration
Workshop Item 1 - ISO 9001: 2008 migration Joint IAF-ISO Communiqué on migration to ISO 9001: 2008 ISO 9001: 2008 does not contain any new requirements Accredited Certification to ISO 9001:2008 shall not
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61850-10 First edition 2005-05 Communication networks and systems in substations Part 10: Conformance testing IEC 2005 Copyright - all rights reserved No part of this publication
More informationAmerican Association for Laboratory Accreditation
Page 1 of 5 This document describes the accreditation requirements for organizations performing activities associated with Stationary Source Evaluation Testing per the requirements of ASTM D7036 (2004).
More informationISO/IEC INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO/IEC 15426-1 Second edition 2006-06-01 Information technology Automatic identification and data capture techniques Bar code verifier conformance specification Part 1: Linear symbols
More informationISO/IEC INTERNATIONAL STANDARD. Conformity assessment Supplier's declaration of conformity Part 2: Supporting documentation
INTERNATIONAL STANDARD ISO/IEC 17050-2 First edition 2004-10-01 Conformity assessment Supplier's declaration of conformity Part 2: Supporting documentation Évaluation de la conformité Déclaration de conformité
More informationSection Qualifications of Audit teams Qualifications of Auditors Maintenance and Improvement of Competence...
Section 9. SFI 2010-2014 Audit Procedures and Auditor Qualifications and Accreditation Updated January 2011 Section 9 Introduction... 3 1. Scope... 3 2. Normative Reference... 3 3. Terms and Definitions...
More informationMeasuring the effectiveness of your ISMS implementations based on ISO/IEC 27001
Measuring the effectiveness of your ISMS implementations based on ISO/IEC 27001 Information Security Management Systems Guidance series The Information Security Management Systems (ISMS) series of books
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-34400-9 Edition 1 ISO 10005:2005 Edition 2 SOUTH AFRICAN NATIONAL STANDARD Quality management systems Guidelines for quality plans This national standard is the identical implementation
More informationISO/IEC INTERNATIONAL STANDARD. Software engineering Product evaluation Part 3: Process for developers
INTERNATIONAL STANDARD ISO/IEC 14598-3 First edition 2000-02-01 Software engineering Product evaluation Part 3: Process for developers Ingénierie du logiciel Évaluation du produit Partie 3: Procédés pour
More informationConformity assessment Requirements for bodies providing audit and certification of management systems. Part 6:
TECHNICAL SPECIFICATION ISO/IEC TS 17021-6 First edition 2014-12-01 Conformity assessment Requirements for bodies providing audit and certification of management systems Part 6: Competence requirements
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28929-4 ISO 10001:2007 SOUTH AFRICAN NATIONAL STANDARD Quality management Customer satisfaction Guidelines for codes of conduct for organizations This national standard is the identical
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 A TEST LAB TECHNO CORP. 101-104, 1F, A Building, Taoyuan Street Safflower Ridge Industrial Area, Nanshan District Shenzhen, 518055, People s Republic of China
More informationPre-Standard PUBLICLY AVAILABLE SPECIFICATION IEC PAS Batch control. Part 3: General and site recipe models and representation
PUBLICLY AVAILABLE SPECIFICATION Pre-Standard IEC PAS 61512-3 First edition 2004-11 Batch control Part 3: General and site recipe models and representation Reference number IEC/PAS 61512-3:2004(E) Publication
More informationIEC Quality Assessment System for Electronic Components (IECQ System)
IECQ 04-1 Edition 1.0 2010-07 IECQ PUBLICATION IEC Quality Assessment System for Electronic Components (IECQ System) Standard Training Part 1: IECQ Training Body Requirements and Process for IECQ Acceptance
More informationISO Second edition Corrected version Reference number ISO :2012(E)
INTERNATIONAL STANDARD ISO 18436-1 Second edition 2012-11-15 Corrected version 2013-01-15 Condition monitoring and diagnostics of machines Requirements for qualification and assessment of personnel Part
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61850-10 First edition 2005-05 Communication networks and systems in substations Part 10: Conformance testing Reference number IEC 61850-10:2005(E) Publication numbering As from
More informationACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES
ACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES ACCREDITATION SCHEME MANUAL Document Title: Document Number: Various Accreditation Schemes ACCAB-ASM-7.0 CONTROLLED COPY Revision Number Revision
More informationTRAINING COURSE CERTIFICATION (TCC) COURSE REQUIREMENTS
TRAINING COURSE CERTIFICATION (TCC) COURSE REQUIREMENTS Testing and Calibration Laboratory Lead Assessor Training Course Exemplar Global International Training Certification Programs Exemplar Global, Inc.
More informationThis is a preview - click here to buy the full publication TECHNICAL REPORT
TECHNICAL REPORT ISO/IEC TR 14763-2 First edition 2000-07 Information technology Implementation and operation of customer premises cabling Part 2: Planning and installation ISO/IEC 2000 All rights reserved.
More informationInformation technology Service management. Part 10: Concepts and vocabulary
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO/IEC 20000-10 First edition 2018-09 Information technology Service management Part 10: Concepts and vocabulary Technologies de l'information Gestion
More informationAccreditation process (LA-I-02)
Accreditation process (LA-I-02) Bureau of Laboratory Accreditation Department of Science Service Ministry of Science and Technology 75/7 Rama VI Road, Ratchathewi District, Bangkok 10400 Tel: 0-2201-7325,
More informationACCAB. Accreditation Commission For Conformity Assessment Bodies
ACCAB Accreditation Commission For Conformity Assessment Bodies ACCAB Platinum Plus Accreditation For Certification Bodies, Inspection Bodies, Testing & Calibration Laboratories and Medical Laboratories
More informationIEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System)
IECEE 02 Edition 16.0 2016-06-01 IECEE PUBLICATION IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System) Rules of Procedure CB Scheme Scheme of the IECEE
More informationIEC Quality Assessment System for Electronic Components (IECQ System)
IECQ 03-5 Edition 3.0 2014-02 IECQ PUBLICATION IEC Quality Assessment System for Electronic Components (IECQ System) Rules of Procedure Part 5: IECQ HSPM Scheme Hazardous Substance Process Management Requirements
More informationCertification Requirements Competency-based Functional Safety (ISO 26262) Engineer Certification Program
Certification Requirements Competency-based Functional Safety (ISO 26262) Engineer Certification Program Exemplar Global Personnel Certification Programs Exemplar Global is accredited by the Joint Accreditation
More informationISO 5208 INTERNATIONAL STANDARD. Industrial valves Pressure testing of metallic valves
INTERNATIONAL STANDARD ISO 5208 Third edition 2008-08-01 Industrial valves Pressure testing of metallic valves Robinetterie industrielle Essais sous pression des appareils de robinetterie métalliques Reference
More informationInformation Bulletin
Application of Primary and Secondary Reference Documents Version 1.1 Approved for release July 2014 Table of Contents 1.0 Purpose statement... 3 2.0 Audience... 3 3.0 BCA requirements and referenced documents...
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 13584-26 First edition 2000-02-01 Industrial automation systems and integration Parts library Part 26: Logical resource: Information supplier identification Systèmes d'automatisation
More informationIEC Quality Assessment System for Electronic Components (IECQ System)
IECQ 03-5 Edition 5.0 2017-08 IECQ PUBLICATION IEC Quality Assessment System for Electronic Components (IECQ System) Rules of Prodecure Part 5: IECQ HSPM Scheme Hazardous Substance Process Management Requirements
More informationISO/IEC Information technology Open Systems Interconnection The Directory. Part 9: Replication
INTERNATIONAL STANDARD This is a preview - click here to buy the full publication ISO/IEC 9594-9 Seventh edition 2017-05 Information technology Open Systems Interconnection The Directory Part 9: Replication
More informationISO/IEC This is a preview - click here to buy the full publication INTERNATIONAL STANDARD. First edition
INTERNATIONAL STANDARD ISO/IEC 15426-2 First edition 2005-03-15 Information technology Automatic identification and data capture techniques Bar code verifier conformance specification Part 2: Two-dimensional
More informationISO INTERNATIONAL STANDARD. Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
INTERNATIONAL STANDARD ISO 1431-1 Fourth edition 2004-09-01 Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing Caoutchouc vulcanisé ou thermoplastique
More informationAcronem Consulting Australia Pty Ltd
Acronem Consulting Australia Pty Ltd Solutions Engineered Building Codes, Standards and Regulations Energy Efficiency Compliance Insulation Expertise Total R-Value Calculations Marketing Technical Literature
More informationISO/IEC TR TECHNICAL REPORT. Software engineering Product quality Part 4: Quality in use metrics
TECHNICAL REPORT ISO/IEC TR 9126-4 First edition 2004-04-01 Software engineering Product quality Part 4: Quality in use metrics Génie du logiciel Qualité des produits Partie 4: Qualité en métrologie d'usage
More informationIEC System for Certification to Standards relating to Equipment for use in Renewable Energy applications (IECRE System)
IECRE 03 Edition 2.0 2018-08-14 IECRE PUBLICATION IEC System for Certification to Standards relating to Equipment for use in Renewable Energy applications (IECRE System) Marine Energy Operational Management
More informationMinimum Scheme Requirements to Certify Criminal Justice Restraints Described
This document is scheduled to be published in the Federal Register on 07/13/2017 and available online at https://federalregister.gov/d/2017-14638, and on FDsys.gov Billing Code: 4410-18 DEPARTMENT OF JUSTICE
More information