Penetration - Bitumen Method - PNR 12 (automatic)

Transcription

1 Penetration - Bitumen Method - PNR 12 (automatic) Standards depend on the selected accessories ASTM D 5, DIN (obs.), EN 1426, EN , EN , JIS K2207, AASHTO T49 Product group(s): Bitumen, Penetration User group(s): Airports & Aviation, Asphalt, Bitumen, Mastics, Penetration, Regulatory Authorities, Road Research, Tar, Various Scope: The Penetrometer PNR 12 is suitable for measurements according various "Bitumen" methods. Needle-Penetration: To measure the consistancy of semi-solid and solid bituminous mixtures. Rod-Penetration: To measure the apparent viscosity (Bitumen No) of filler aggregates used in bituminous mixtures. Cone-Penetration: To determinate the consistancy of hot-applied, fuel-resistant joint sealants with or with out being immersed in fuel or oil. The Penetration is used to measure the resistance which a material under specified test conditions provides against being pierced by a specifically shaped penetrator. Beside the configuration of the penetrator used, prime importance attaches to such factors as temperature, time and load specified by the different standard methods of test. Fully "Automatic Surface-Detection" on bitumen beneath a standardized layer of water Jog-Shuttle driven menue (turn & push) Movement by stepper motor LED illumination PNR 12 - Automatic Penetrometer Depending on accessories suitable for: Needle-Penetration Rod-Penetration Cone-Penetration and further applications Accessories (plungers, needles etc.) are required, but not included. All test kits that fit the PNR 10 & 21 models are suitable for the PNR 12, too. (Except for the Ball-Penetration Method) More details are mentioned in the "Order Number" section Technical Data Measuring Range: Max. Test Load: Resolution: Test Duration: 0 to 55 mm 2 kg 0.01 mm 0.1 to seconds (preset standard duration: 5 seconds) Start Delay: adjustable up to max. of sec. (2.78 hours) Data Output: USB interface to connect printer or USB-stick 0-Point Detector: for electrically conductive samples Desk space (WxHxD): 350 x 400 x 600 mm Weight: 16 kg Page: 1

2 Main Unit PNR 12 - Automatic Penetrometer Accessories have to be selected according to the standard. (Suitable for: Needle-, Cone-, Rod-Penetration and further methods) Features: manual positioning by Jog-Wheel operation electronic positioning to a preset depth with Memory-function surface detection by conductivity sensor 16 user programs possible data transfer to USB-Stick possible extra bright LED-sample illumination Microcomputer, electronic distance measuring device, stepper motor for exact positioning, 24 V safety voltage supply, stable base plate and housing. Microcomputer: Large graphical monochrome display, intuitive graphical menu, status feedback to operator, Jog-Wheel driven menu (turn & push), storage of last 200 measurements. The Surface-Detection Software of the PNR 12 will be activated by sensor-plungers. This option will detect the surface of bitumen-samples underneath a layer of water, it starts the standardized test sequence and reports the results automatically. Electronic Elements: Distance measuring device (1/100 mm), stepper motor, ultra bright LED-sample illumination on flexible arm, electronic detector for conductive samples, USB-interface for printer & memorystick. Mechanical Elements: Penetrometer base plate with leveling feet and removable aluminum test table, instrument housing two colored powder coated, splash water protected membrane keyboard, plunger holder with solenoid release mechanism and observation lens with fl exible arm. Note: Accessories in compliance with the different test standards or samples (e.g. needles, cones, plunger etc.) are to be ordered separately. Power supply: 100/240 V, 50/60 Hz Test Kit "Needle - ASTM" ASTM D 5 - AASHTO T49 - JIS K2207 Suitable for: bituminous materials, chocolate, compact powder, lipstick, soap, yeast 3 standard needles, 2.5 g, brass/steel, precision made ( ) 1 plunger 47.5 g ( ) 1 load weight 50 g ( ) 5 sample jars I, Ø 55 x 35 mm ( ) 1 tempering bath ( ) 1 petri dish, Ø 43 x 11 mm ( ) Test Kit "Needle - EN" EN 1426 (IP 49 obs.) Suitable for: bituminous materials, chocolate, compact powder, lipstick, soap, yeast 1 plunger 47.5 g ( ) 1 load weight 50 g ( ) 5 sample jars I, Ø 55 x 35 mm ( ) 1 sample jar III, Ø 70 x 45 mm ( ) 1 sample jar V, Ø 55 x 60 mm ( ) 1 reduction ring Ø 36 / 53 x 20 mm ( ) 1 reduction ring Ø 36 / 53 x 30 mm ( ) 1 tempering bath with serpentine heat exchanger tube ( ) Page: 2

3 1 thermometer ASTM 63C ( ) 1 thermometer ASTM 64C ( ) Note! for standard acc. to IP 49 obs. is required: 150g load weights ( & ) and thermometer ASTM 17C ( ) Test Kit "Needle - manually <350 PU" ASTM D 5 (<350 PU) - EN 1426 (<330 PU) Suitable for: Bitumen with an expected immersion depth of less than 35 mm 1 plunger 97.5 g ( ) 3 sample jars I, Ø 55 x 35 mm ( ) 1 sample jar III, Ø 70 x 45 mm ( ) 1 tempering bath (Ø 160 x 80 mm) with serpentine heat exchanger tube ( ) 1 thermometer ASTM 63C ( ) Note! for manual surface detection with PNR Test Kit "Needle - automatic <160 PU" ASTM D 5 (<160 PU) - EN 1426 (<160 PU) Suitable for: Bitumen with an expected immersion depth of less than 16 mm after 5 seconds with 100 g weight 1 sensor plunger 97.5 g ( ) 3 sample jars I, Ø 55 x 35 mm ( ) 1 tempering bath (Ø 160 x 80 mm) with serpentine heat exchanger tube ( ) 1 temperature sensor PT-100 ( ) Note! for automatic surface detection with PNR 12 only! Test Kit "Needle - manually >330 PU" ASTM D 5 (>350 PU) - EN 1426 (>330 PU) Suitable for: Bitumen with an expected immersion depth of more than 33 mm 3 long standard needles 2.5 g, brass/steel, precision, ( ) 1 plunger 97.5 g ( ) 3 sample jars I, Ø 55 x 70 mm ( ) 1 tempering bath (Ø 160 x 80 mm) with serpentine heat exchanger tube ( ) 1 thermometer ASTM 63C ( ) Note! for manual surface detection with PNR Test Kit "Needle - automatic <160 PU modified" ASTM D 5 (<160 PU) Suitable for: modified Bitumen with an expected immersion depth of less than 16 mm after 60 seconds with 200 g weight 1 sensor plunger 97.5 g ( ) Page: 3

4 1 load weight, 100 g ( ) 3 sample jars I, Ø 55 x 35 mm ( ) 1 tempering bath (Ø 160 x 80 mm) ( ) 1 temperature sensor PT-100 ( ) Note! for automatic surface detection with PNR 12 only! Test Kit "Ram - Bitumen Number" (van der Baan) EN Suitable for: bitumen 1 ram Ø 8 mm, 15 g, aluminum ( ) 1 sample jar Ø 30 mm x 30 mm ( ) Test Kit "Optional Hollow Cone - Filler" ASTM D EN Suitable for: Sealant, Fillers 1 optional hollow cone g, brass/steel ( ) 1 plunger 47.5 g ( ) 1 sample jar I, Ø 55 x 35 mm ( ) 1 tempering bath ( ) 1 spacer plate for tempering bath ( ) Options & Accessories Standard Needle, 2.5 g (precision made) ASTM D 5 - EN JIS K2207 (lp 49 obs.) and other applications Standard Needle, 2.5 g (factory certified) ASTM D 5 - EN JIS K2207 (lp 49 obs.) and other applications Standard Needle, 2.5 g (officially certified) EN 1426 (lp 49 obs.) Standard Needle, 2.5 g (officially certified) ASTM D 5 (suitable for EN 1426 and lp 49 obs.) Sensor-Plunger - Force 47.5 g (PNR 12 only) 1 load weight of 2/5/10/50 or 100 g can be added. (Same like ) Sensor-Plunger - Force 97.5 g (PNR 12 only) 1 load weight of 2/5/10/50 or 100 g can be added. A plunger with an extremely sensitive force sensor for the automatic surface detection underneath a layer of water. It activates the related the PNR 12 software automatically. Suitable for Bitumen-samples <160 PU! Page: 4

5 Sensor-Plunger - Force 97.5 g extra long (PNR 12 only) Up to 4 load weights of 2/5/10/50 or 100 g can be added. (Same like ) Additional Weight for Sensor-Plunger, 50 g Additional Weight for Sensor-Plunger, 100 g Additional Weight for Sensor-Plunger, 10 g Additional Weight for Sensor-Plunger, 5 g Additional Weight for Sensor-Plunger, 2 g Serial Impact Printer for single sheets & continuous paper, with USB-interface to record data like test results, duration of test, etc. (instead of a PC) Supplied with: 1 data transmission cable, 1 ink ribbon (black) Technical Data: Line spacing: 80 characters per line (10 cpi) Page size : 257 x 364 mm (sheet), 254 x mm (roll) Ports: serial, USB (1.1) & parallel Dimensions: 37 x 28 x 16 cm (WxDxH) Weight: 5 kg Power supply: 220/240 V, 50/60 Hz Electronic Stop Watch with electric start-input Power supply: 100/240 V, 50/60 Hz Halogen Lamp extra bright, to be placed beside the penetrometer; especially useful when testing bituminous materials under water surface Power supply: 230 V, 50 Hz For tempering applications directly in the bath (e.g. sample pre-tempering) and / or for heating & cooling of instruments without circulation pump (e.g. PNR-tempering dish). Stainless steel bath. Thermostat with analog display, integrated heater, cooler, pump, over-temperature protection, pump-pressure control. Supplied with: 2 bath covers, 1 pump-set for external tasks, 1 thermometer (0 to +100 : 0.5 C) Note: Insulated hose-set is recommended. Technical Data: Working range: -10 to +100 C (at +5 to +40 C ambient temp.) Display / Resolution: analog / 1 C Control: analog Heater capacity: 1500 W Cooling capacity: 250 W at +200 C Pump-Pressure capacity: 17 l/min, 300 mbar Bath opening: 30 x 35 x 20 cm (WxDxH) Safety class / Bath fluid: 1 / NFL (water / water-antifreeze-mix only) Volume: l Dimensions / Weight: 36 x 75 x 40 cm (WxDxH), 31 kg Power supply: 230 V, 50/60 Hz, 2000 W, EU-plug Page: 5

6 Like but: Heater capacity: 1000 W Power supply: 115 V, 60 Hz, 1500 W For tempering applications directly in the bath (e.g. sample pre-tempering) and / or for heating & cooling of instruments without circulation pump (e.g. PNR-tempering dish). Stainless steel bath. Thermostat with digital display, splash-proof keypad, integrated heater, cooler, pump, over-temperature protection, pump-pressure control. Supplied with: 2 bath covers, 1 pump-set for external tasks Note: Insulated hose-set is recommended. Technical Data: Working range: -10 to +100 C (at +5 to +40 C ambient temp.) Display / Resolution: LED / 0.1 & 0.01 C Control: PID Heater capacity: 2000 W Cooling capacity: 250 W at +200 C Pump-Pressure capacity: 17 l/min, 300 mbar Bath opening: 30 x 35 x 20 cm (WxDxH) Safety class / Bath fluid: 1 / NFL (Non Flammable Liquids only) Volume: l Dimensions / Weight: 36 x 75 x 40 cm (WxDxH), 31 kg Power supply: 230 V, 50/60 Hz, 2500 W, EU-plug Like but: Heater capacity: 1200 W Power supply: 115 V, 60 Hz, 1700 W Spare Parts Sensor-Plunger - Force 97.5 g (PNR 12 only) 1 load weight of 2/5/10/50 or 100 g can be added. A plunger with an extremely sensitive force sensor for the automatic surface detection underneath a layer of water. It activates the related the PNR 12 software automatically. Suitable for Bitumen-samples <160 PU! Electronic surface detector for conductive samples with contact hook and connection wire Lamps for built-in illuminator, 3.7 V; pack of 5, lens shaped Bulb for halogen lamp Ink Ribbon, black, for serial impact printer Thermometer ASTM 17C Range: +19 to +27 : 0.1 C Length: 275 mm, Immersion: total, Ø 6.5 mm Thermometer ASTM 17C Range: +19 to +27 : 0.1 C (officially certified) Thermometer ASTM 17F Range: +66 to +80 : 0.2 F Length: 275 mm, Immersion: total, Ø 6.5 mm Page: 6

7 Thermometer ASTM 17F Range: +66 to +80 : 0.2 F (officially certified) Thermometer ASTM 38C / IP 78C Range: +24 to +78 : 0.2 C Length: 395 mm, Immersion: 100 mm, Ø 7 mm Thermometer ASTM 38C / IP 78C Range: +24 to +78 : 0.2 C (officially certified) Order Guideline Minimum equipment: Spares (approx. 1 year): Additional requirements: 1 x & Test Kit (needle, cone etc.), Accessories , Thermometer Page: 7