Shutter Assembly Guide Frame Accessory

Transcription

1 Shutter Assembly Guide Frame Accessory SIZE: FS1 3-pole Cat. No.: WLG3SHUT1L For Use With: Circuit Breaker Adapters WLG _ 13 Installation Instructions Instruction No.: Danger Peligro Danger! Hazardous Voltage Will cause death or serious injury. Tensión peligrosa. Pueda causar la muerte o lesiones graves. Tension dangereuse. Danger de mort ou risque de blessures graves. WARNING Shock and arc flash hazard May cause serious injury or death. Only qualified personnel should work on this equipment, after becoming thoroughly familiar with all warnings, safety notices, and maintenance procedures contained herein and on the devices. For the purposes of this manual and product labels, qualified personnel is one who is familiar with the installation, construction, or operation of the equipment and the hazards involved. In addition, s/he has the following qualifications: (a) is trained and authorized to energize, de-energize, clear, ground, and tag circuits and equipment in accordance with established safety practices. (b) is trained in the proper care and use of protective gear equipment such as rubber gloves, hard hat, safety glasses or face shields, flash clothing, etc., in accordance with established safety procedures (c) is trained in rendering first aid. Only authorized repair or replacement parts shall be used in this equipment / 8

2 NOTICE These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency to be met in connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the Purchaser s s purposes, the matter should be referred to the local Siemens Sales Office. The contents of this instruction manual shall not become part of or modify any prior or existing agreement, commitment or relationship. The sales contract contains the entire obligations of Siemens. The warranty contained in the contract between the parties is the sole warranty of Siemens. Any statements contained herein do not create new warranties or modify the existing warranty. TRADEMARKS Unless otherwise noted, all names identified by are registered trademarks of Siemens AG or Siemens Industry, Inc. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. The following is the bill of materials and tools required to assemble shutter for frame size 1. Bill of Material for frame size 1 1. Shutter Subassembly (1) 2. Shutter Mounting Assemblies (2) 3. Shutter Mounting Assembly top (1) 4. Shutter Mounting Assembly bottom (1) 5. Socket head cap screws M6x10 with locking coating (6) Tools Required A. ¼i inch hblade flat thead screwdriver di B. M5 Allen Wrench A B / 8

3 Danger Peligro Danger! Hazardous Voltage Tensión peligrosa. Tension dangereuse. Will cause death or serious injury. Pueda causar la muerte o lesiones graves. Danger de mort ou risque de blessures graves. 1 INSTALL SHUTTER MOUNTS Shutter mounting assemblies are used to support the shutter assembly. There are two shutter mounts on the left side (Item 2) and two on the right side (Item 3 and 4) per shutter (as noted by the arrows below. Place each shutter mounting assembly into the cradle locking holes. Ensure that the locating dowel pins are seated. The front tines will pass through the rectangular opening in the cradle sidewall. Use the screwdriver blade to spread the front tines by inserting the screwdriver between the tines, and rotating the blade in clockwise and counter-clockwise motions. This will lock the shutter mounting assemblies to the cradle. left side right side / 8

4 Danger Peligro Danger! Hazardous Voltage Tensión peligrosa. Tension dangereuse. Will cause death or serious injury. Pueda causar la muerte o lesiones graves. Danger de mort ou risque de blessures graves. Place the Shutter subassembly (Item 1) in the way and sequence as noted by the arrows below. TOP VIEW / 8

5 Danger Peligro Danger! Hazardous Voltage Tensión peligrosa. Tension dangereuse. Will cause death or serious injury. Pueda causar la muerte o lesiones graves. Danger de mort ou risque de blessures graves. 2 INSTALL SHUTTER TO MOUNTS The shutter subassembly (Item 1) is secured to the shutter mounting assemblies (Item 2, 3 and 4) with six socket head cap screws M6x10 with locking coating (Item 5) as shown below. Torque each screw to 30 lb-in (four places) / 8

6 Danger Peligro Danger! Hazardous Voltage Tensión peligrosa. Tension dangereuse. Will cause death or serious injury. Pueda causar la muerte o lesiones graves. Danger de mort ou risque de blessures graves. 3 OPTIONAL: INSTALLING PADLOCK The WL shutter prevents incidental contact with primary conductors when the circuit breaker is removed from the cradle. At the user s option, a padlock may be installed through the arm on the right side of shutter assembly, as a means of locking out direct access to the primary conductors. One padlock through the arm is required to lock out primary conductor direct access. For frame size 1, a padlock may only be used on the right side. NOTE Remove padlocks before inserting breaker into the cradle / 8

7 This page is intentionally blank / 8

8 Siemens Industry, Inc Triangle Parkway Norcross, GA Printed in USA / Siemens Industry, Inc. All Rights reserved Siemens is a registered trademark of Siemens AG. Product names mentioned may be Trademarks of their respective companies. Specifications are subject to change without notice.