ADPRO FastTrace 2X/2E & ift Series. Supported IP Cameras. March 2017 Doc _12 Software version XO

Transcription

1 FastTrace 2X/2E & ift Series Supported IP Cameras March 2017 Doc _12 Software version XO

2

3 FastTrace 2X/2E & ift Series Supported IP Cameras Disclaimer The contents of this document are provided on an "as is" basis. No representation or warranty (either express or implied) is made as to the completeness, accuracy, or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications without obligation and without further notice. Except as otherwise provided, all warranties, express or implied, including without limitation any implied warranties of merchantability and fitness for a particular purpose are expressly excluded. Intellectual Property and Copyright This document includes registered and unregistered trademarks. All trademarks displayed are the trademarks of their respective owners. Your use of this document does not constitute or create a license or any other right to use the name and/or trademark and/or label. This document is subject to copyright owned by Xtralis. You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify, or publish any contents of this document without the express prior written consent of Xtralis. General Warning This product must only be installed, configured and used strictly in accordance with the General Terms and Conditions, User Manual and product documents available from Xtralis. All proper health and safety precautions must be taken during the installation, commissioning, and maintenance of the product. The system should not be connected to a power source until all the components have been installed. Proper safety precautions must be taken during tests and maintenance of the products when these are still connected to the power source. Failure to do so or tampering with the electronics inside the products can result in an electric shock causing injury or death and may cause equipment damage. Xtralis is not responsible and cannot be held accountable for any liability that may arise due to improper use of the equipment and/or failure to take proper precautions. Only persons trained through an Xtralis accredited training course can install, test and maintain the system. Liability You agree to install, configure, and use the products strictly in accordance with the User Manual and product documents available from Xtralis. Xtralis is not liable to you or any other person for incidental, indirect, or consequential loss, expense or damages of any kind including without limitation, loss of business, loss of profits, or loss of data arising out of your use of the products. Without limiting this general disclaimer the following specific warnings and disclaimers also apply: Fitness for Purpose You agree that you have been provided with a reasonable opportunity to appraise the products and have made your own independent assessment of the fitness or suitability of the products for your purpose. You acknowledge that you have not relied on any oral or written information, representation, or advice given by or on behalf of Xtralis or its representatives. Total Liability To the fullest extent permitted by law that any limitation or exclusion cannot apply, the total liability of Xtralis in relation to the products is limited to: (i) in the case of services, the cost of having the services supplied again; or (ii) in the case of goods, the lowest cost of replacing the goods, acquiring equivalent goods or having the goods repaired. Indemnification You agree to fully indemnify and hold Xtralis harmless for any claim, cost, demand, or damage (including legal costs on a full indemnity basis) incurred or which may be incurred arising from your use of the products. Miscellaneous If any provision outlined above is found to be invalid or unenforceable by a court of law, such invalidity or unenforceability will not affect the remainder which will continue in full force and effect. All rights not expressly granted are reserved. Document Conventions The following typographic conventions are used in this document. Convention Bold Description Used to denote: emphasis Used for names of menus, menu options, toolbar buttons Italics Used to denote: references to other parts of this document or other documents. Used for the result of an action The following icons are used in this document. Icon Description Note. This icon indicates information of special interest that will help the reader make full use of the product, optimise performance, etc. Failure to read the note will not result in physical harm to the reader, or damage to equipment or data. Caution! This icon indicates danger to equipment. The danger can be loss of data, physical damage to the equipment, or permanent corruption of configuration details. Warning! This icon indicates danger of physical harm to the reader. Not following instructions may lead to death or permanent injury. Warning! This icon indicates danger of electric shock. This may lead to death or permanent injury. Warning! This icon indicates that there is a danger of inhaling dangerous substances. This may lead to death or permanent injury _12 3

4 Supported IP Cameras Trade Name Statement FastTrace 2X/2E & ift Series Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel,, IntrusionTrace, LoiterTrace, ClientTrace, SmokeTrace, XOa, XOh, itrace, icommand, irespond, icommission, ipir, and FMST are trademarks and/or registered trademarks of Xtralis and/or its subsidiaries in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective holder(s). Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/or label. Contact Us UK and Europe D-A-CH The Americas Middle East Asia Australia and New Zealand _12

5 FastTrace 2X/2E & ift Series Contents Supported IP Cameras 1 Introduction Scope of this Document Camera Firmware Versions Performance Management of the IP Video Streams Supported IP Cameras for FastTrace 2X/2E and ift Series Abbreviations IP Camera Configuration Integrated IP Cameras IP Camera Manufacturers ACTI Arecont Avigilon Axis Bosch Brickcom Hikvision Hikvision AVE Honeywell JVC Panasonic Pelco Samsung Sanyo Sony Generic Driver URLs ONVIF Profile S Driver American Dynamics/Tyco Avigilon Canon Concept Pro Dahua Eneo Genie CCTV Geovision Grundig IC Realtime IndigoVision LG Moog Santec Scati _12 5

6 Supported IP Cameras FastTrace 2X/2E & ift Series Sony Vista Vivotek Xeno Appendix A: Ronix IP Camera Setup _12

7 FastTrace 2X/2E & ift Series 1 Introduction Supported IP Cameras 1.1 Scope of this Document This document contains the list of supported H.264 IP cameras and H.264 IP video encoders for: The FastTrace 2X/2E (i.e. the FastTrace 2X/2E devices with product numbers starting with 56 and 58). The ift Series (product numbers starting with 60, 61, and 63). For the supported cameras and video encoders for the FastTrace 2 (i.e. the FastTrace 2 devices with product numbers starting with 55), see the FastTrace 2 Series Supported IP Camera List (29579). Wherever device is mentioned in this document, it refers to both the FastTrace 2 Series (2X/2E) and the ift Series (ift/ift-e). The lists in this document contain only cameras that Xtralis has tested and approved according to its own protocols. However, this list is not binding and makes no claim to be complete. If you want to use IP cameras or video encoders that are not listed in this document, Xtralis does not guarantee that the cameras will function on the devices. Xtralis does not guarantee correct operation because cameras may show unexpected with firmware versions not tested by Xtralis. Xtralis does not offer any support for untested cameras. The latest versions of this document and any other referenced documents are available from the Xtralis Security Solutions Support site Camera Firmware Versions IP cameras are expected to perform best at their latest firmware version. Please refer to the manufacturer s website for full details on the latest available firmware. In the exceptional case that new camera firmware would not be backwards compatible with its previous version(s) as originally tested with the devices, Xtralis will make the best effort possible to correct the situation in a reasonable amount of time. 1.3 Performance IP cameras tend to generate bitrates that can go up to 4 5 Mbps per camera, especially for Full HD or Megapixel cameras. Depending on brand and type, the IP cameras can handle 2 or 3. Specifically and even key differentiator to traditional DVRs/NVRs, the devices use multiple per camera to be able to manage live viewing, recording, transmission, and analytics in one box. Knowing that any network connected device has its limits concerning bandwidth, disk access, throughput, storage capacity, number of please notice the following rules of thumb for the devices: FastTrace 2X/2E: up to 20 x 5.1 Megapixel IP fps + max. 20 analytic channels (Obtained by Xtralis in-house testing using 20 x Axis P1357 IP fps with FastTrace 2E model). FastTrace 2E and ift Series with software version XOa 3 and above: up to 32 x 5.1 Megapixel IP cameras + max. 32 analytic channels (also depending on hardware). Note H.264 decoding is extremely sensitive to bandwidth use fluctuations related to camera view scenario and image content activity. Even changing IP camera brand will result in bandwidth use differences and influence the device s performance _12 7

8 Supported IP Cameras 2 Management of the IP Video Streams FastTrace 2X/2E & ift Series of video stream Number of independent camera Continuous recording setting Event recording setting Live stream A 1 Settings for continuous recording, event recording and live stream are equal. No analytics stream available* B 2 (standard for untested cameras) = Analytics stream** Programmable Setting of event recording or analytics stream** C 2 Programmable Programmable D 3 Programmable Programmable Setting of continuous recording or event recording* Setting of continuous recording, or event recording, or analytics stream** * No analytics stream available. Therefore, no motion detection, sabotage detection, post-motion detection, Xtralis analytic applications (LoiterTrace, IntrusionTrace, SmokeTrace ), local video output, or generating quad pictures available. Such cameras are not recommended for Video Central Platinum or EMS. ** Analytics stream; used for motion detection, sabotage detection, post-motion detection, Xtralis analytic applications (LoiterTrace, IntrusionTrace, SmokeTrace ), local video output, and generating quad pictures: - Default analytics stream: CIF/SIF or the next available higher resolution with a maximum of 640 x 480, with Qnormal quality, at 5 fps. The minimum horizontal resolution is 352 pixels. - With software version XO 4.0 and above: aspect ratio and quality of the analytics stream are selectable, with a maximum resolution of 640 x 480. The actual resolution depends on the video that the camera provides and that the XO software can access. You can check the actual analytics stream for each camera in the XO client, in the Video Inputs screen _12

9 FastTrace 2X/2E & ift Series Supported IP Cameras 3 Supported IP Cameras for FastTrace 2X/2E and ift Series 3.1 Abbreviations Abbreviation fps FW HD MP NA NOK NT SD Description Frames per second Firmware High definition Megapixel Not available Not OK, cannot be used on FastTrace 2X/2E or ift Series device Not tested Standard definition 3.2 IP Camera Configuration Xtralis recommends the following for configuring the IP cameras: To set the camera s IP address, use the manufacturer s camera discovery tool. Avoid using management or administration tools. Before connecting the camera to the device, reset the camera to the default values, except for the IP address (unless you are using the Generic Driver). Note that some camera functions may require specific settings in the camera web interface. This is indicated in the notes and footnotes in this document. With software version XO 4.0, it is possible to access the camera s web interface from within the XO client. For details, see the XO Client Software User Manual (21796). Corridor mode in the camera is supported with XOa ; with XO 4.0 it is also supported with analytics. 180 panoramic view in the camera is not supported. 3.3 Integrated IP Cameras The cameras listed in this chapter have been tested and approved for use with the FastTrace 2X/2E and ift Series devices. 3.4 IP Camera Manufacturers Click the manufacturer to go to the supported IP cameras from that manufacturer: With manufacturer s driver: With Generic Driver With ONVIF Profile S driver: ACTI Arecont Avigilon Axis Bosch Brickcom Hikvision/AVE Honeywell JVC Panasonic Pelco Samsung Sanyo Sony American Dynamics/Tyco Avigilon Canon Concept Pro Dahua Eneo Genie CCTV Geovision Grundig IC Realtime IndigoVision LG Moog Santec Scati Sony Vista Vivotek Xeno 26742_12 9

10 Supported IP Cameras 4 ACTI FastTrace 2X/2E & ift Series E53 1 HD 5 MP 2 B NA NA NA NA E54 HD 5 MP 2 B NA NA NA E64 HD 1 MP 2 B NA NA NA XOa E83 1 HD 5 MP 2 B NA NA NA NA E85 HD 1 MP 2 B NA NA NA XOa E86 HD 3 MP 2 B NA NA NA XOa TCD-500 SD 2 B Audio in TCM-1231 HD 2 B Audio in TCM-3511 HD 2 B Audio in NA NA NA TCM-4101 SD 2 B Audio in NA NA TCM-4301 HD 2 B Audio in NA NA TCM-5311 HD 2 B Audio in TCM-5611 HD 2 B Audio in TCM-6630 SD 2 B Audio in TCM-7411 HD 2 B Audio in NA NA Yes NA Maximum usable framerate: 15 fps. Do not use B2 frames. When available (for E-Series) use Baseline Profile instead of Highline Profile. Untested camera models: some features may not function; restricted to maximum 2. 1 This camera model has not officially been tested by Xtralis, but was implemented in a specific project _12

11 FastTrace 2X/2E & ift Series 5 Arecont Supported IP Cameras 3105 HD 2 C NA NA NA NA 8185 HD 1 A NA NA NA NA The Arecont 8185 camera uses 4 IP video channels on the FastTrace 2X/2E and ift Series. No analytics stream available (see Management of the IP Video Streams). Untested camera models may not work at all _12 11

12 Supported IP Cameras 6 Avigilon FastTrace 2X/2E & ift Series 1.0-H3-B2 HD 1 MP 2 B In: ext. mic NA 1 NA XOa MP-H3-B2 HD 2 MP 2 B NOK NA MP-HD-H264-D1 HD 2 MP 2 B 2.0W-H3-B01-IR HD 2 MP 2 B In: NOK Audio out Audio in Audio out NA NA Untested camera models: some features may not function; restricted to maximum 2. With firmware version XO 4.0, keep the following issue in mind: When you default certain Avigilon cameras (such as the 2.0MP-HD-H264-D1), they only have one H264 stream enabled at the highest resolution. They can then no longer be enabled on the device. Solution: open the camera web interface; decrease the resolution of the primary stream, and then enable the second stream as an H264 type stream. You can then enable the camera on the device. Audio out is only available from version XO One output is available when using this camera with the ONVIF Profile S driver instead of the Avigilon driver. Xtralis recommends using the ONVIF Profile S driver _12

13 FastTrace 2X/2E & ift Series 7 Axis A8004-VE C3003-E 2 Network Horn Speaker F41 HD 1 MP 720p 3 D NA NA NA HD 2 MP 1080p In: built-in mic Out: built-in speaker 1 In: built-in mic Out: speaker 3 x I 3 x O Supported IP Cameras NA XOa NA NA XO D Audio in 4 I or O NA XOa M1011 SD 2 B NA NA NA NA M1011-W SD 2 B NA NA NA NA M1031-W SD 2 B M1054 M1114/-E HD 1 MP 720p HD 1 MP 720p 3 D In: built-in mic or audio in Out: built-in speaker 1 In: built-in mic or audio in M1125/-E 3 Full HD 3 D NA NA NA NA NA 3 D NA NA NA NA XOa M1143-L SD 3 D NA NT NA M3004 M3005/-V M3006 M3007 Dewarp HD 1 MP 720p HD 2 MP 1080p HD 3 MP 1080p 3 D NA NA NA D NA NA NA D NA NA HD 5 MP 2 B NA NA NA XOa M3011 SD 2 B NA NA NA NA M3014 HD 1 MP 2 B NA NA NA NA M3025 M3027-PVE Dewarp M3037-PVE Dewarp HD 2 MP 1080p 3 D NA 5 MP 2 B NA 5 MP 2 B In: built-in mic Audio out 1 NA Yes XOa Yes XOa M3044-V/WV 4 720p 3 D NA NA NA XO M3045-V 5 Full HD 3 D NA NA NA XOa M3114-R M3204 M5014 HD 1 MP 720p HD 1 MP 720p HD 1 MP 720p 2 B NA NA NA D NA NA NA D NA NA Yes, only for setting Audio out over IP is supported from device firmware version XOa This is an IP speaker, not a camera, but it requires 1 IP video channel on XO devices. 3 Privacy mask is not working. 4 This camera model has not officially been tested by Xtralis, but was implemented in a specific project. 5 OSD not working _12 13

14 Supported IP Cameras FastTrace 2X/2E & ift Series M Video Encoder P x D NA NA NT XOa HD 1 MP 720p P1311 SD 3 D Audio in P1343 SD 3 D Audio in P1344 P1346 HD 1 MP 720p HD 3 MP 1080p 3 D NA NT NA D Audio in 3 D Audio in P1347 HD 5 MP 2 B Audio in P SD 2 B P1354 P1355/-E HD 1 MP 720p HD 2 MP 1080p In: built-in mic or audio in 3 D Audio in 3 D P1357/-E HD 5 MP 3 D P1365 P1425-E/LE P1428-E HD 2 MP 1080p HD 2 MP 1080p 4K Ultra HD 8 MP 3 D In: built-in mic or audio in In: built-in mic or audio in In: built-in mic or audio in 3 D NA 3 D NA NA NA NA NA NA NA NA NA NA NA NA NA NA XOa NA XOa NA XOa P1435-E/LE 3 Full HD 3 D NA NA XOa P3215-V/VE P3225-LVE HD 2 MP 1080p HD 2 MP 1080p P3301/-V SD 3 D P3304 HD 1 MP 720p 3 D NA NA NA XOa D NA NA NOK XOa D P3343/-V SD 3 D In: built-in mic or audio in In: built-in mic or audio in In: built-in mic or audio in P3343-VE SD 3 D Audio in P3344/-V P3344-VE HD 1 MP 720p HD 1 MP 720p 3 D P3346 HD 3 MP 3 D P3354 HD 1 MP 720p In: built-in mic or audio in 3 D Audio in In: built-in mic or audio in NA NA NA NA NA NA NA NA NA NA NA NA D NA NA NA Brightness/contrast/saturation is not working. 2 Do NOT rotate or mirror image when defining privacy mask. 3 Privacy mask only via web interface _12

15 FastTrace 2X/2E & ift Series Supported IP Cameras P3364- V/LV/VE/LVE P3365/-V/VE HD 1 MP 720p HD 2 MP 1080p 3 D P3367/-V/-VE HD 5 MP 3 D P3384 P5414-E HD 1 MP 720p HD 1 MP 720p In: built-in mic or audio in 3 D Audio in 3 D In: built-in mic or audio in In: built-in mic or audio in NT NA XOa NA XOa NA NT NA D NT 4 I or O Yes P5512 SD 3 D NT NT Yes P5515-E 1 Full HD 3 D NA NA Yes (iris NA) XOa P5522/-E SD 3 D NT NT Yes P5532/E SD 3 D NT NT Yes P5534/-E HD 1 MP 720p 2 B NT 4 I or O Yes P5624-E 2 720p 3 D NA NA P5635-E 3 HD 2 MP 1080p Q1602 SD 3 D Q1604 Q1614/-E Q1615 Q1635 Q1755 Q1765-LE Q1921/-E Thermal Q2901-E Thermal Q3505 HD 1 MP 720p HD 1 MP 720p HD 2 MP 1080p HD 2 MP 1080p HD 2 MP 1080i HD 2 MP 1080p Yes (iris NA) XOa B NT NT Yes XOa D 3 D 3 D 3 D 3 D In: built-in mic or audio in In: built-in mic or audio in In: built-in mic or audio in In: built-in mic or audio in In: built-in mic or audio in In: built-in mic or audio in NA NA I or O NA I or O NA XOa I or O NA XOa D NT 2 I or O SD 2 B In: built-in mic or audio in Zoom only Zoom only NA I or O NA NA SD 2 B NT NT NA XOa HD 2 MP 1080p 3 D Audio in 2 I or O NA XOa Q3709-PVE x B NA NA NA XOa Q6032-E SD 3 D NA NA Yes NA Q6035-E HD 2 MP 1080p 2 B NT NT Yes Q6042-E SD 3 D NA NA Yes Q6044-E HD 1 MP 720p 3 D NA NA Yes Only brightness available, no contrast/saturation. 2 Privacy mask only via web interface. 3 Manual focus only goes to farthest or nearest point, no focus in between. 4 Camera uses 3 channels (3 IP addresses/3 IP channels). 180 panoramic view is not supported. Available resolutions depend on capture mode. Disable camera in XO client before changing the capture mode. OSD via web interface _12 15

16 Supported IP Cameras FastTrace 2X/2E & ift Series Q6045-E Q6045-E-MkII Q6114-E 1 HD 2 MP 1080p HD 2 MP 1080p HD 1 MP 720p 3 D NA NA Yes D NA NA Yes XOa D NA NA Yes XOa Q6128-E 2 4K 3 D NA NA Q7401 Video Encoder Q7404 Video Encoder Q7411 Video Encoder SD 3 D Audio in Audio out 3 Yes (iris NA) XOa I or O Yes SD 3 D Audio in 2 I or O Yes SD 3 D Audio in I: min. 2, max. 4. O: min. 0, max. 2. Yes Audio out over IP is supported from device firmware version XOa Untested camera models: some features may not function; restricted to maximum 2. 1 Contrast setting not available. Camera is limited to 25 fps. 2 Contrast setting not available. Privacy mask only in web interface. 3 Audio out over IP is supported from device firmware version XOa PTZ is only available with Axis PTZ driver installed. See to obtain the correct driver. 5 PTZ is only available with Axis PTZ driver installed. See to obtain the correct driver _12

17 FastTrace 2X/2E & ift Series 8 Bosch Autodome 7000HD HD 1080p 2 B NT Autodome 800 HD Series 1 HD 1080p 2 B NT OK Yes (focus & iris NA) Yes (focus & iris NA) Supported IP Cameras Dinion HD 1080p IVA HD 1080p 2 B Line in OK NA Dinion HD 720 IVA HD 720p 2 B NA NA NA NA Dinion IP 7000 HD HD 1080p 2 B Line in OK NA Dinion IP Starlight 7000 HD Flexidome HD 1080P- HDR-VR-IVA Flexidome IP outdoor 5000 IR 2 Flexidome IP Dynamic 7000 Flexidome IP Starlight 7000 RD 2 HD 720p 2 B NOK HD 1080p 2 B NT 1920 x B In: ext. mic HD 1080p 2 B NT 1280 x B In: ext. mic NA NA NA XOa NA NA XOa ( ) Flexidome NDN-498-P SD 2 B NT OK NA Flexidome NDN-921-P HD 720p 2 B NT OK NA NDC 225 P SD 2 B Line in OK NA NTC-265-PI HD 720p 2 B NOK NA Untested camera models: some features may not function; restricted to maximum 2. 1 Maximum resolution is 1280 x 720, 15 fps. 2 Maximum 15 fps. OSD not available; privacy mask only via web interface _12 17

18 Supported IP Cameras 9 Brickcom FastTrace 2X/2E & ift Series CB-100Ae-08 HD 1 MP 2 B NA NA NA CB-102Ap HD 1 MP 2 B NA NA NA FB-131Ap-71 HD 1.3 MP 2 B NA NA NA FD-100Ap-73-M HD 1 MP 2 B NA NA NA MD-100Ap-00 HD 1 MP 2 B NA NA NA OB-100Ap-73 HD 1 MP 2 B NA NA NA OSD-040E-36X 1 SD 2 B NA NA Yes VD-100Ap-73 HD 1 MP 2 B NA NA NA XX-YYYAp-ZZZ: professional model = up to 30 fps. XX-YYYAe-ZZZ: economy model = up to 15 fps. Camera configuration: some Brickcom camera types have VMS configuration settings: - Disable WS security for these camera types. - ONVIF 1.0 (default) / 2.0: both are possible, but 1.0 is recommended. - Sync (default) / Async: Sync is recommended. Untested camera models: some features may not function; restricted to maximum 2. 1 Up to 25 fps _12

19 FastTrace 2X/2E & ift Series 10 Hikvision Supported IP Cameras 10.1 Hikvision # of video DS-2CD2012-I HD 1.3 MP 2 B NA NA NA DS-2CD2032-I HD 3 MP 2 B NA NA NA DS-2CD2332-I 1 HD 3 MP 2 B NT NT NA XOa NA DS-2CD2512F-IWS 1 HD 1.3 MP 2 B NT NT NA XOa NA DS-2CD2632F-I 1 HD 3 MP 2 B NT NT NA XOa NA DS-2CD2642FWD-IS 2 4 MP 2 B Audio in Audio out NA XO build DS-2CD2642FWD-IZ 3 HD 3 MP 2 B NA NA NA XOa DS-2CD2742FWD-IS 2 4 MP 2 B Audio in Audio out NA XO DS-2CD2T42WD-I3 4 HD 4 MP 2 B NA NA NA XOa DS-2CD2T42WD-I5 4 HD 4 MP 2 B NA NA NA XOa DS-2CD2T42WD-I8 4 HD 4 MP 2 B NA NA NA XOa DS-2CD4025FWD-A 1280 x B DS-2CD4B26FWD- IZS x B DS-2CD6412FWD-10 HD 1.3 MP 2 B Audio in Audio out 5 In: ext. mic Audio out Audio in Audio out 5 DS-2CD6412FWD-20 HD 1.3 MP 2 B Audio in NOK NA XOa NA XO build build build build build V5.4.1 build NA NA DS-2CD7153-E 7 HD 2 MP 2 B NA NA NA DS-2CD762MF-IFB HD 1.3 MP 2 B NOK NA NA DS-2CD8153F-E HD 2 MP 2 B NOK NA NA DS-2CD833F-E 7 SD 2 B NOK DS-2CD883F-E 7 HD 5 MP 2 B DS-2DE5220I-AE 8 Full HD 2 B Audio in Audio out 5 In: ext. mic Audio out NA NA Yes, focus and iris NOK XOa V5.3.8 build This camera model has not officially been tested by Xtralis, but was implemented in a specific project. 2 Inputs only work if arming schedule is enabled in web interface: Configuration > Event > Basic Event > Alarm input > Arming schedule. 3 Privacy mask only via web interface. Analytic resolution is 512 x 288 or 509 x 288 depending on event resolution. Recorded resolution is 352 x Frame rate is limited for certain resolutions. If you select an unsupported frame rate, the frame rate falls back to 1 fps. Max ; ; and Supported fps values are: 1, 2, 4, 6, 8, 10, 12, 15, 16, 18, 20, 22, and 25. The analytics resolution is CIF, but is displayed as 509 x 288 in the Info pane in the XO client. 5 Audio out over IP is supported from device firmware version XOa Autofocus can be enabled via web interface. I/O must be enabled in web interface. 7 Do not upgrade the camera firmware as newer firmware does not support the same interface as used by the device. 8 Frame rate is limited to 25 fps. 5 fps not available _12 19

20 Supported IP Cameras FastTrace 2X/2E & ift Series # of video DS-2DF1-512 SD 2 B NOK Yes DS-2DF7284-A HD 2 MP 2 B Audio in NT Yes XOa DS-2DF7286-AEL 1 Full HD 2 B In: ext. mic Audio out 7 x I Yes, focus and iris NOK XOa Added support for Hikvision firmware Version 5. Audio out over IP is available from device firmware version XOa Untested camera models: some features may not function; restricted to maximum AVE # of video AVE-IP3EXIRBN1 3 MP 2 B NA NA NA XOa V AVE-IP3EXTNH2 3 MP 2 B NA NA NA XOa V Use Hikvision drivers for these AVE cameras. Maximum 20 fps at highest resolution. Untested camera models: some features may not function; restricted to maximum 2. 1 Privacy mask only via web interface _12

21 FastTrace 2X/2E & ift Series 11 Honeywell # of video Video stream H3W2GR x B H3W2GR x B H3W4GR x B In: built-in mic or line in Audio out In: built-in mic or line in Audio out In: built-in mic or line in Audio out H4D3PRV2 3 3 MP 2 B NA NA Zoom and focus Zoom and focus Zoom and focus Zoom and manual focus XOa XOa XOa XOa HW00.0.R, H4D3PRV3 3 3 MP 2 B NA NA NA XOa H4D8GR MP 2 B NOK H4L2GR x B H4W2GR x B H4W2GR x B H4W4GR x B In: line in Audio out In: line in Audio out In: line in Audio out In: line in Audio out NA XO Zoom and focus Zoom and focus Zoom and focus Zoom and focus XOa XOa XOa XOa HBD1PR x B NA NA NA XOa HBD2PR1X Full HD 2 B NA NA NA XOa HBD3PR1 8 3 MP 2 B NA NA NA XOa HBD3PR2 8 3 MP 2 B NA NA HBD8GR MP 2 B NT HBL2GR x B HBW2GR x B In: line in Audio out In: line in Audio out Zoom and manual focus Zoom and focus Zoom and focus Zoom and focus XOa HW00.0.R, XO XOa XOa Supported IP Cameras HW00.0.R build: HW00.0.R build: HW00.0.R build: build: HW00.0.R, build: HW00.14 build: HW00.14.R build: HW00.0.R build: HW00.0.R build: HW00.0.R build: HW00.0.R, build: HW00.0.R, build: HW00.0.R, build: build: HW00.14, build: HW00.14.R build: HW00.0.R build: Frame rate is limited to 25 fps. For audio in via built-in mic: in camera web interface, set Audio in type to Mic. Enable I/O in camera web interface (Alarm Setup > Alarm > Enable). 2 Frame rate is limited to 20 fps at 2688 x 1520 and 2560 x 1440, 25 fps at all other resolutions. For audio in via built-in mic: in camera web interface, set Audio in type to Mic; for audio in via external mic: set to Line in. Enable I/O in camera web interface (Alarm Setup > Alarm > Enable). 3 Frame rate is limited to 20 fps at 3 MP, and 25 fps at lower resolutions. 4 Enable I/O in camera web interface. If 12 MP, use max. 16 cameras on one device. 5 Frame rate is limited to 25 fps. Enable I/O in camera web interface. 6 Frame rate is limited to 20 fps at 2688 x 1520 and 2560 x 1440, 25 fps at all other resolutions. Enable I/O in web interface. 7 Frame rate is limited to 25 fps. 8 Frame rate is limited to 20 fps at 3 MP (2304 x 1296) resolution. 9 This camera model has not officially been tested by Xtralis, but was implemented in a specific project. If 12 MP, use max. 16 cameras on one device _12 21

22 Supported IP Cameras FastTrace 2X/2E & ift Series # of video Video stream HBW2GR x B HBW4GR x B HCL2G x B HCW2G x B HCW4G x B HDZ302LIK p 2 B HDZ302LIW p 2 B In: line in Audio out In: line in Audio out In: built-in mic or line in Audio out In: built-in mic or line in Audio out In: built-in mic or line in Audio out In: line in Audio out In: line in Audio out 7 x I 7 x I Zoom and focus Zoom and focus XOa XOa NA XOa NA XOa NA XOa Yes, no autofocus or iris Yes, no autofocus or iris XOa XOa HED1PR x B NA NA NA XOa HED3PR3 9 3 MP 2 B NA NA NA XOa HFD6GR1 10 Fisheye 6 MP 2 B In: built-in mic or line in Audio out NA XO HW00.0.R build: HW00.0.R build: HW00.14.R build: HW00.0.R build: HW00.0.R build: R.3 build: R.3 build: HW00.0.R, build: HW00.0.R, build: HW00.0 build: For audio out: in the camera web interface, choose Setup > Audio Setup > Audio and enable the audio stream on the sub-stream (analytics), and set the speaker volume to the maximum value. Audio out is only available with firmware version XO 4.0 and above. New firmware may be required; check the list for the correct firmware version and build. OSD and privacy mask only via web interface. For H3W2GR1, H3W2GR2, H3W4GR1, H4W2GR1, H4W2GR2, H4W4GR1, HBW2GR1, HBW2GR3, HBW4GR1, HCW2G, and HCW4G: Analytics image has a 4:3 aspect ratio, this is the cropped 16:9 image. The cut-off parts are not taken into account for alarm events including analytics; detection will not occur in the cut-off parts. Quad/live 1 Enable I/O in web interface. Disable the audio stream on the sub-stream (analytics); as this may cause NO VIDEO. 2 Frame rate is limited to 20 fps at 2688 x 1520 and 2560 x 1440, 25 fps at all other resolutions. 3 Frame rate is limited to 25 fps. Use web interface for focus. 4 Frame rate is limited to 25 fps. Use web interface for focus. Enable I/O in web interface. 5 Frame rate is limited to 20 fps at 2688 x 1520 and 2560 x 1440, 25 fps at all other resolutions. Enable I/O in web interface. Use web interface for focus. 6 Frame rate is limited to 25 fps. Enable I/O in web interface. Contrast not available. To control IR lights via XO client, set IR lights to manual control in the web interface (Setup > Peripheral > IR Lights). 7 Frame rate is limited to 25 fps. Enable I/O in web interface. Contrast not available. Wiper and IR lights are controllable via XO client (Live Video) from version XO 4.0. Set IR lights to manual control in the web interface (Setup > Peripheral > IR Lights). 8 Frame rate is limited to 25 fps. 9 Frame rate is limited to 20 fps at highest resolution; 25 fps for other resolutions. 10 Use Ceiling Mode and Fisheye only (Setup > Camera Settings > Properties > Fisheye). Enable I/O in web interface _12

23 FastTrace 2X/2E & ift Series Supported IP Cameras alarm images are produced from the cropped stream. Set up the system (analytics, PIR detector FOV, double-knock ) from the cropped analytics stream, not from the high-resolution live stream. For H4D3PRV2, H4D3PRV3, H4L2GR1, HBD1PR1, HBD2PRX, HBD3PR1, HBD3PR2, HBL2GR1, HCL2G, HDZ302LIK, HDZ302LIW, HED1PR3, and HED3PR3: Analytics image has a 4:3 aspect ratio, but has a 16:9 image squeezed into it. This distorts the horizontal dimensions in the calibration for analytics applications such as IntrusionTrace; it makes detection unreliable. Make sure to perform bounding box calibration for this camera. Corridor mode in the camera is supported with XOa ; with XO 4.0 it is also supported with analytics _12 23

24 Supported IP Cameras 12 JVC VN-H157WPU HD 1080p 2 B In: ext. mic FastTrace 2X/2E & ift Series NA VN-H237 HD 1080p 2 B NA NA NA XOa VN-H257VPBU HD 1080p 2 B NA Zoom VN-H37U HD 1080p 2 B NA NA NA NA VN-H557U HD 1080p 2 B In: ext. mic VN-H57U HD 1080p 2 B In: ext. mic VN- H657WP/WPB HD 1080p 2 B NA Yes spl2971 NA Yes XOa spl2841 VN-T16U SD 2 B NOK NOK NA VN-T216 VPRU SD 2 B NA NOK NA j No support for brightness/contrast/saturation. Untested camera models: some features may not function; restricted to maximum _12

25 FastTrace 2X/2E & ift Series 13 Panasonic WV-NW502S HD 1.3 MP 2 B Audio in External I/O Supported IP Cameras Cam FW NA WV-SFN631L 1 HD 3 MP 3 D Audio in 3 x I NA XOa WV-SFV631L 2 HD 3 MP 3 D Audio in 3 x I NA XOa WV-SP105 HD 1.3 MP 2 B NA NA NA WV-SPN631 HD 3 MP 2 B Audio in 3 x I NA XOa WV-SW316L HD 1.3 MP 2 B Audio in NT NA WV-SW355E HD 1.3 MP 2 B Audio in WV-SW395 HD 1.3 MP 2 B Audio in External I/O External I/O NA Yes WV-SW559 HD 1.3 MP 2 B NT NT NA NA WV-SW598 HD 1080p 2 B NA 3 x I Yes Compared to similar IP cameras, Panasonic uses significantly higher bandwidth. Untested camera models: some features may not function; restricted to maximum 2. 1 Zoom and brightness only available via web interface. 2 Privacy mask and brightness only via web interface. No saturation or contrast _12 25

26 Supported IP Cameras 14 Pelco FastTrace 2X/2E & ift Series D5118-FW1 1 HD 1.3 MP 2 B NOK NOK Yes NA IM x960 2 B NA NOK 3 XOa A0.0 IX10 HD 1.3 MP 2 B NOK NOK NA NA IX30 4 HD 3.1 MP 2 B NOK NOK NA A IXE20 5 HD 2.1 MP 2 B NOK NOK NA A IXS0 SD 2 B NOK NOK NA A Spectra HD S5230 TI314-X Thermal HD 2MP 2 B NT NT Yes XOa x B NOK NOK NA O Highest resolution cannot be selected. Pelco does not report a detailed cam type to FastTrace 2X/2E or ift Series. Single stream operation: both Pelco must have the same aspect ratio. Therefore, in the XO client, you will only see a list of resolutions with the same aspect ratio as stream 1. If you want to use a different aspect ratio, you must change the aspect ratio of stream 1 in the camera s web interface first. Untested camera models: some features may not function; restricted to maximum 2. 1 Maximum resolution is 1280 x Disable audio in XO client. No OSD or privacy mask. 3 Zoom and focus only available via web interface. 4 Maximum resolution is 1600 x Maximum resolution is 1600 x _12

27 FastTrace 2X/2E & ift Series 15 Samsung SNB-1000 SD 3 D Audio in SNB-5000 HD 3 D Audio in SNB HD 3 D Audio in SNB Full HD 3 D In: built-in mic or audio in device FW Supported IP Cameras NA NA NA V3.01 NA _ NA XOa _ SND HD 3 D NA NOK NA _ SND-5061P 1 HD 3 D NA NOK NA _ SND HD 3 D SND-L6083R x D In: built-in mic or audio in In: built-in mic NA NA NA XOa XOa _ _ SNF HD 3 D Audio in NA NA _ SNO-5080R 1 HD 3 D NA SNO-L6083R x D Audio in NA NA SNP-3120 SD 3 D Audio in SNP-6200RH 1 HD 2 MP 3 D Audio in SNP-6321H 1 Full HD 2 B Audio in 4 SNP-L5233H x D In: ext. mic SNP-L6233H x D In: ext. mic 4 SNV-3120 SD 3 D Audio in 4 x I 4 x I 4 x I 4 x I NA _ XOa _ Yes NA Yes Yes, focus NOK Yes, focus NOK Yes, focus & iris NOK XOa XOa XO XOa NA S/W 1.02_ ISP 1.02_ _ Yes NA SNV-5080P 1 HD 3 D NOK NOK NA _ (ISP 2.66) SNV-5080R 1 HD 3 D NOK NOK NA NA SNV HD 3 D In: built-in mic SNV-6084R 1 HD 3 D Audio in SNV HD 3 MP 3 D Audio in NA XOa _ NA _ NA XOa _ Frame rate no longer limited to 8 fps with XO 4.0 and above. 2 OSD and privacy mask only via web interface. Set audio to G.711 in camera web interface. 3 Frame rate is limited to 20 fps. 4 Set audio to G.711 in camera web interface (otherwise NO VIDEO). 5 OSD only via web interface. Set audio to G.711 and select the option Apply power to ext. mic in camera web interface. No contrast setting. 6 OSD only via web interface _12 27

28 Supported IP Cameras FastTrace 2X/2E & ift Series device FW SNV-L6013R 1 Full HD 3 D Audio in NA NA XO _ SPE-100 Video Encoder SPE-101 Video Encoder 2 SPE-400 Video Encoder SD 3 D Audio in Yes NA SD 3 D NA NA NT _ SD 3 D Audio in Yes XOa _ The I-frame distance varies from 0.5 second to 4 seconds, depending on the framerate. I-frame distances < 4 seconds can increase the bandwidth and disk usage. Maximum 8 fps for all Samsung cameras on highest resolution, except when indicated (see footnotes with specific camera type). Untested camera models: some features may not function; restricted to maximum 2. 1 OSD and privacy mask only via web interface. 2 Frame rate no longer limited to 8 fps with XO 4.0 and above _12

29 FastTrace 2X/2E & ift Series 16 Sanyo VCC-HD2500P HD (1080p) 3 D Audio in Ext. mic (NT) VCC-HD3500P HD 3 D Audio in VCC-HD4600P HD 3 D Audio in VCC-HD5400P HD 3 D Audio in VCC-HD5600P HD (1080p) 3 D Audio in Ext. mic (NT) (NT) 4 x I 8 x I (NT) Supported IP Cameras NA NA NA NA NA NA Yes NA Yes NT NA Only double-chip cameras will be supported. These are the models 2500, 3500, 4600, 5400, and The one-chip models will not be supported: 2100, 2300, 3100, and Maximum usable resolution is 1280 x 720. Untested camera models: some features may not function; restricted to maximum _12 29

30 Supported IP Cameras 17 Sony FastTrace 2X/2E & ift Series SNC-CH110 1 HD 720p 2 B Audio in NA NA SNC-CH120 HD 720p 2 B Audio in SNC-CH140 HD 720p 2 B Audio in SNC-CH160 HD 720p 2 B SNC-CH180 2 HD 720p 2 B In: audio in, ext. mic In: audio in, ext. mic NA NA NA NA NA NA NA NA SNC-CH210 HD 1080p 2 B NA NA XOa SNC-CH220 1 HD 1080p 2 B NA SNC-CH240 HD 1080p 2 B SNC-CH260 HD 1080p 2 B SNC-CH280 HD 1080p 2 B SNC-DH110T HD 720p 2 B In: audio in, ext. mic In: audio in, ext. mic In: audio in, ext. mic In: audio in, ext. mic (NT) (NT) NA NA NA NA NA NA NA NA SNC-DH120 HD 720p 2 B NA NA NA XOa SNC-DH140 HD 720p 2 B In: audio in, ext. mic (NT) SNC-DH160 HD 720p 2 B Audio in SNC-DH180 SD 2 B Audio in SNC-DH220T HD 1080p 2 B NA SNC-DH240 HD 1080p 2 B SNC-DH260 HD 1080p 2 B In: audio in, ext. mic In: audio in, ext. mic (NT) NA NA Yes NA NA NA NA XOa NA NA NA NA SNC-EB602R x B NA NA NOK XOa SNC-EM600 HD 720p 2 B NA NA NA SNC-EM632R 3 Full HD 2 B NA NA SNC-EP521 4 SD 2 B In: ext. mic 5 SNC-HM662 Dewarp HD 5 MP 2 B In: audio in, ext. mic Only focus XOa OK XOa NA XOa If 4:3 resolutions are required, make sure the camera is set accordingly; and likewise for 16:9 resolutions. The two must have the same aspect ratio x 720 is not supported. 3 This camera also works with the ONVIF Profile S driver. The Sony driver always uses CBR; the ONVIF driver uses VBR. 4 Maximum 12 fps. OSD can display only 1 item at a time. 5 Enable audio in web interface before connecting to device. Audio may present some noise _12

31 FastTrace 2X/2E & ift Series Supported IP Cameras SNC-RH124 SNC-RH164 SNC-RS 44/46/N/P 1 SNC-RS 84/86/N/P 1 HD 2 B Audio in SD 2 B SD 2 B In: audio in, ext. mic In: audio in, ext. mic 4 x I 4 x I Yes NA Yes NA Yes NA SNC-VB600B HD 720p 2 B NOK NOK NA SNC-VB630 HD 1080p 2 B NOK NOK NA SNC-VM600B HD 1080p 2 B NOK SNC-WR600 HD 720p 2 B NA 4 x I NA XOa Yes NA SNC-XM x B NA NT NA XOa SNC-XM632 3 Full HD 2 B In: built-in mic NA NA XOa Support for on-board analytics (DEPA) for 5 th and 6 th generation camera models. Privacy masking has been disabled from firmware version V Untested camera models: may result in default resolution selection (as Sony does not return the supported resolutions); restricted to maximum 2. The list above contains only the Sony cameras that Xtralis has tested and approved according to its own protocols. It is possible (but not guaranteed) that similar Sony cameras, using the exact same chipsets as the tested cameras but with different bodies, also function correctly. It concerns the following camera types: Similar to SNC-EM600: Similar to SNC-EM632R: Similar to SNC-VB630: SNC-EB600 SNC-EM601 SNC-EM602RC SNC-VB600 (with I/O:, ) SNC-VM600 (with I/O:, ) SNC-VM601 (with I/O:, ) SNC-VM602R (with I/O:, ) SNC-EB630 SNC-EM630 SNC-EM631 SNC-EM632RC Similar to SNC-HM662: SNC-CX600 SNC-CX600W Similar to SNC-XM632: SNC-XM636 SNC-VB632D (with I/O:, ) SNC-VM630 (with I/O:, ) SNC-VM631 (with I/O:, ) SNC-VM632R (with I/O:, ) Similar to SNC-WR600: SNC-WR602C (with I/O: 4 x I, ) SNC-XM637 SNC-WR630 (with I/O: 4 x I, ) SNC-WR632C (with I/O: 4 x I, ) 1 N = NTSC; P = PAL. 2 This camera model has not officially been tested by Xtralis, but was implemented in a specific project. 3 This camera also works with the ONVIF Profile S driver. The Sony driver always uses CBR; the ONVIF driver uses VBR. When using the Sony driver, the bitrate displayed in the camera s web interface may not correspond with the real bitrate as set in the XO client _12 31

32 Supported IP Cameras 18 Generic Driver URLs FastTrace 2X/2E & ift Series Below, you find a list of known URLs that work with the generic IP camera driver. For more information on the generic driver, see Generic Driver for IP Camera (27197). Note Xtralis welcomes your feedback on URLs not listed in this document that you may have used successfully with the generic driver. If possible, please provide details on brand, type, camera firmware version, I/O functionality, and used URLs. Arecont AV20365DN 4 possible, only 1 at a time, entered as url2 (NO analytics), 5 MP was not possible to stream. rtsp://ip/h264.sdp1?x0=0&x1=2560&y0=0&y1=1920&res=full&fps=5&bitrate=1024&qp=25&ssn=20 rtsp://ip/h264.sdp4?x0=0&x1=2560&y0=0&y1=1920&res=full&fps=5&bitrate=1024&qp=25&ssn=25 rtsp://ip/h264.sdp2?x0=0&x1=2560&y0=0&y1=1920&res=full&fps=5&bitrate=1024&qp=25&ssn=30 rtsp://ip/h264.sdp3?x0=0&x1=2560&y0=0&y1=1920&res=full&fps=5&bitrate=1024&qp=25&ssn=35 Axis 7001 encoder Only 1 stream possible, entered as url2 (NO analytics): rtsp://ip:554/axis-media/media.amp?videocodec=h264&compression=50&fps=15&videokey frameinterval=60&resolution=4cif&audio=0 Axis M7016 encoder 16-channel encoder with 4 IP addresses (4 channels per IP address). Per channel: 2 possible, entered as url1 and url2; do not use url3 with this encoder. URLs below are for camera 1. Replace camera=1 in URLs below by camera=2, camera=3, camera=4 for the other cameras. url1 (analytics): rtsp://ip:554/axis-media/media.amp?camera=1&videocodec=h264&compression=50&fps=5 &videokeyframeinteval=20&resolution=cif&audio=0 url2 (event recording): rtsp://ip:554/axis-media/media.amp?camera=1&videocodec=h264&compression=50&fps=15 &videokeyframeinteval=60&resolution=4cif&audio=0 For ulr1, the analytics stream, framerate (fps) must be = 5, I-frame interval (videokeyframeinterval) = 20 (framerate x 4), and resolution = CIF. For url2, you can set fps up to 30; then set videokeyframeinterval to 4 x fps. Possible resolutions for url2: CIF, 2CIF, 4CIF, D1. Compression: Axis Q6000-E Has 4 cameras on board, requires 4 IP channels. 360 panoramic view is not supported for this camera. URLs below are for camera 1. Replace camera=1 in URLs below by camera=2, camera=3, camera=4 for the other cameras. url1 (analytics): rtsp://ip_address/axismedia/media.amp?camera=1&resolution=480x270&fps=5&videokeyframeinterval=19&datetime=yes url2 (event recording): rtsp://ip-address/axismedia/media.amp?camera=1&resolution=1280x720&fps=25&videokeyframeinterval=99&datetime=yes datetime=yes in the URL is required for OSD. After making changes in the camera web interface, disable/enable the camera in the XO client to apply the changes. Live view resolution options (on right-click): 480 x 270, 1280 x 720, hard disk stream. Choosing 480 x _12

33 FastTrace 2X/2E & ift Series gives 1280 x 270. Requires 60 W midspan/power injector. Supported IP Cameras CCTI 316B-01 (thermal) url1 (analytics): rtsp://admin:12345@ip/h264/ch01/sub/av_stream url2 (recording): rtsp://admin:12345@ip/h264/ch01/main/av_stream Concept Pro CBP6324DN-IP4M url1 (hi-res/event recording, 2688 x 1512, 15 fps, GOP = 45, 280 kb/s): rtsp://ip_address/snl/live1/1 url2: (analytics stream, CIF, 5 fps, GOP = 20, 6 kb/s): rtsp://ip_address/snl/live1/2 OSD and privacy mask only available via web interface. Can take up to 5 minutes to restore connection after interruption. Concept Pro CVP9328DNIR-IP 2 : url1 (hi-res/event recording, 1920 x 1080, 25 fps, GOP = 75, VBR 2000, 270 kb/s): rtsp://ip_address/snl/live1/1 url2 (analytics, CIF, 5 fps, GOP = 20, 6 kb/s): rtsp://ip_address/snl/live1/2 OSD and privacy mask only available via web interface. Can take up to 8 minutes to restore connection after interruption. Dahua DHI-HCVR5104HE-S2 For security reasons, use a firmware version above , Build Date: Channel number and stream numbers are indicated in bold in the URLs below. Encoder channel 1: url1: rtsp://ip_address/cam/realmonitor?channel=1&subtype=1&unicast=true&proto=onvif url2: rtsp://ip_address/cam/realmonitor?channel=1&subtype=0&unicast=true&proto=onvif Encoder channel 2: url1: rtsp://ip_address/cam/realmonitor?channel=2&subtype=1&unicast=true&proto=onvif url2: rtsp://ip_address/cam/realmonitor?channel=2&subtype=0&unicast=true&proto=onvif Refer to the screenshot below to set up the encoder correctly. Note: The encoder only supports an I-frame distance of max. 2 seconds. This is within the XO working range, but ideally it should be 4 seconds _12 33

34 Supported IP Cameras FastTrace 2X/2E & ift Series Dvtel C F (thermal) 1 stream only (320 x 240)! rtsp://ip:554/2?videocodec=h.264 DRS Watchmaster IP Elite 3000 (thermal) 1 stream only! rtsp://ip:554/2?videocodec=h.264 Flir FC 324-S 1 URL for both analytics and event recording. Default username: admin, default password: fliradmin rtsp:// :554/ch0 Minimum required camera firmware: BU1.2. Define ch0 in the camera, in the same menu as the image size, but with label Stream Name. Set IDR Factor to 1 in the camera, in the same menu as the image size, but with label IDR Factor. To get clear targets without saturation, set the thermal image settings as follows: ROI Full Use always Plateau Algorithm: recommended value 175 ITT: 117 AGC Gain: between 4 and 7 DDE: between 19 and 24. For Flir FC Series cameras, set up the compression engines as follows: Frame rate 5 fps I-frame distance 20 Bitrate: variable (not CBR); around 1 Mbps for good image reconstruction _12

35 FastTrace 2X/2E & ift Series For camera firmware v1.32, also apply the following rules: use UDP communications when using RTSP connection stream set the quality to HIGH in all the in use disable the internal camera analytics. Supported IP Cameras LG LNP3020T This is a PTZ camera, only streaming possible. url1 (low res): rtsp://ip:554/slave-0 url2 (high res): rtsp://ip:554/master-0 Now also supported with ONVIF Profile S driver. Norbain / Vista VK2 url1: rtsp://a.b.c.d:554/1/stream1 url2: rtsp://a.b.c.d:554/1/stream3 This camera has a 2-second interval for I-frames, hence a high bitrate. Now also supported with ONVIF Profile S driver. Ronix IP Camera Default login name: root, password: root url1 rtsp://ip/cam0_1 url2 rtsp://ip/cam0_0 For additional setup instructions, see Appendix A: Ronix IP Camera Setup on page 56. Santec SNC-8322HO 4 possible, but lowest frame rate is 13 fps, so not usable for analytics. Default login name: admin, default password: 9999 rtsp://ip:554/h264 rtsp://ip:554/h264_2 rtsp://ip:554/h264_3 rtsp://ip:554/h264_4 Now also supported with ONVIF Profile S driver. Visicom 3S Vision DNMP6031IR Default login name: root, password: root url1 (low res, analytics): rtsp://ip:554/cam1/h264-1 url2 (high res, recording): rtsp://ip:554/cam1/h264 Visicom 3S Vision NWS-4071 encoder (4-channel) Default login name: root, password: root url1 (low res, analytics): rtsp://ip:554/cam1/h264-1 url2 (high res, recording): rtsp://ip:554/cam1/h264 These URLs are for channel 1; for the other channels, replace cam1 by cam2, cam3, or cam _12 35

36 Supported IP Cameras 19 ONVIF Profile S Driver FastTrace 2X/2E & ift Series Use the ONVIF Profile S driver to connect your ONVIF Profile S compliant IP camera. Note Xtralis welcomes your feedback on cameras not listed in this document that you may have used successfully with the ONVIF Profile S driver. If possible, please provide details on brand, type, camera firmware version, I/O functionality, or any extra information. This chapter lists cameras that work with the ONVIF Profile S driver with firmware version XO 4, and that Xtralis has tested and approved according to its own protocols American Dynamics/Tyco Illustra 600 ADCi600-D321 1 Illustra 610 ACDi610-D011 2 Illustra Pro 3MP Mini-Dome indoor 3 Illustra Pro PTZ outdoor 3 SD 2 B Full HD 2 B 3 MP 2 B In: ext. mic In: ext. mic In: ext. mic NA XOa AD NA XOa AD NOK Zoom, focus4 XOa C11078AD9 Full HD 2 B NOK NOK Yes 5 XOa A10475ZZZ 395 Before activating the camera in the XO client, use the camera s web interface to: Set the second stream to H264. Enable audio in (audio recording). 1 Set the GOV size for both. 2 OSD and privacy mask only via web interface. 3 OSD, privacy mask, and brightness/contrast/saturation only via web interface. 4 Zoom and focus only via web interface. 5 Focus and iris only via web interface _12

37 FastTrace 2X/2E & ift Series 19.2 Avigilon Supported IP Cameras 1.0-H3-B2 HD 1 MP 2 B In: ext. mic NA XOa This camera also works with the Avigilon driver, but then I/O is not supported _12 37

38 Supported IP Cameras 19.3 Canon FastTrace 2X/2E & ift Series VB-H43 2 MP 2 B In: ext. mic VB-R x B In: ext. mic VB-S30D x B In: ext. mic Yes XOa Yes 1 XOa Yes 1 XOa Perform the following settings in the camera web interface: - Enable second stream as follows: Choose Video. Set the option H.264(2) to Enable. - For VB-H43: Choose Setting Page > Server. Under WS-Security, set the option Check Time on Authentication to Do not check. For I/O to work: in the camera web interface, enable the option Events - External Device Input Event. - For VB-R11/VB-S30D (better video quality when motion): Select the option Do not use bit rate control. Brightness/contrast/saturation not working. OSD only via web interface. The list above contains only the Canon cameras that Xtralis has tested and approved according to its own protocols. It is possible (but not guaranteed) that similar Canon cameras, using the same firmware, also function correctly. 1 Not possible to set home position via preset 0 in XO client; home position must be set in camera. 2 Maximum frame rate is 15 fps/stream when using 2 ; 30 fps possible for 1 stream _12

39 FastTrace 2X/2E & ift Series 19.4 Concept Pro Supported IP Cameras AIR4526-IP x B NOK NA NA CVP9324DNIR-IP Full HD 2 B NOK NOK NA VHSDIR-670EXT- IP 2 VHSDIR-870EXT- IP x B NOK 1920 x B NOK I: NOK I: NOK Yes, focus and iris NOK Yes device FW XOa XOa XOa XOa v v v v Max. 18 fps. OSD and privacy mask only via web interface. 1 OSD and privacy mask only via web interface. 2 Brightness/contrast/saturation not OK. PTZ preset positions working except position 0. 3 Contrast not OK. PTZ preset positions working except position _12 39

40 Supported IP Cameras 19.5 Dahua FastTrace 2X/2E & ift Series DH-SD6AW230- HNI 1 IPC-EBW Fisheye IPC- HDBW2300R-Z IPC- HDBW4220E 3 IPC- HDBW5221E-Z IPC- HDBW5421E-Z # of video Video stream Full HD 2 B NOK 4000 x B In: builtin or I NOK ext. mic Yes, iris NOK NA 3 MP 2 B NA NA Zoom Full HD 2 B NA NA NA Full HD 2 B NA 4 MP 2 K 2 B NOK Zoom Zoom IPC-HDW1000S 4 720p 2 B NA NA NA IPC- HFW2300R-Z 5 3 MP 2 B NA NA Zoom & autofocus IPC-HFW4220E 6 Full HD 2 B NA NA NA IPC- HFW5221E-Z IPC- HFW5421E-Z Full HD 2 B NOK 4 MP 2 K 2 B NOK SD59230S-HN 3 Full HD 2 B NA I: NOK Zoom & manual focus Zoom & manual focus Yes, iris NOK device FW XOa XOa XOa XOa XOa XOa XOa XOa XOa XOa XOa XOa R N.NR, build R, build Software: R, build Web version: ONVIF version: Dahua 00.6.R, build: Dahua R, build Dahua R, build Software: R, build Web version: Software: R, build Web version: ONVIF version: Dahua R, build Dahua R, build Dahua R, build: R.A N.NR, build Web version: PTZ version: RHNTEJ All models except IPC-EBW81200: disable audio (otherwise NO VIDEO). The list above contains only the Dahua cameras that Xtralis has tested and approved according to its own protocols. It is possible (but not guaranteed) that similar Dahua cameras, using the same firmware, also function correctly. It concerns the following camera types: 1 OSD only via web interface. No brightness, contrast, saturation. 2 s 2880 x 2880 and 4000 x 3000 are not supported by XO client. Current max x Camera web interface password can be different from ONVIF password. Use admin/admin for ONVIF. Set main stream and substream using web interface. Web interface reports 352 x 288 instead of 384 x 288 as indicated by XO client. Set audio sampling frequency to 8k for correct audio. OSD and privacy mask only via web interface. 3 OSD and privacy mask only via web interface. 4 Disable in-camera motion detection (otherwise NO VIDEO). 5 This camera model has not officially been tested by Xtralis, but was implemented in a specific project. 6 Max. 20 fps at highest resolution _12

41 FastTrace 2X/2E & ift Series Same firmware as IPC-HDW1000S: IPC-HFW1000S IPC-HFW1100 IPC-HD1000C Same firmware as SD59230S-HN: DH-SD6C220S-HN DH-SD6C230S-HN DH-SD59212S-HN DH-SD59220S-HN DH-SD59230S-HN DH-SD63220S-HN DH-SD63230S-HN DH-SD50220S-HN DH-SD50230S-HN Supported IP Cameras DH-SD40212S-HN DH-SD42212S-HN DH-SD42C212S-HN DH-SD32203S-HN DH-SDZ2020S-N DH-SDZ2030S-N DH-SDZH2030S-N DH-SDZW2030S-N 26742_12 41

42 Supported IP Cameras 19.6 Eneo FastTrace 2X/2E & ift Series NXB-980IR37M HD 2 MP 2 B NA NA NA XOa T8_release PXB-1080Z03IR HD 2 MP 2 B NA NA Zoom XOa ds PXD-5360F01IR Dewarp PXD-5362F01IR Dewarp HD 5 MP 2 B HD 5 MP 2 B In: built-in mic In: built-in mic NA XOa NA NA XOa NA The list above contains only the Eneo cameras that Xtralis has tested and approved according to its own protocols. It is possible (but not guaranteed) that similar Eneo cameras, using the same firmware, also function correctly. It concerns the following camera types: 2 MP box / bullet / dome cameras: PXB-1080Z03 PXB-2080MIR B PXB-2080Z03 PXB-2180Z03 PXC-2080CS PXC-2080Z03 PXD-2080MIR C PXD-2080Z03 Thermal cameras: PTB-1025F09 PTB-1125F09 PTB-1125F13 PTB-1125F19 PTB-1125F35 PTZ cameras: NXD-2012PTZ1080 NXD-2030PTZ1080 Entry cameras: NXB-980IR3516M NXD-980IR3516P NXD-980IR3516M NXD-980IR37M NXD-980IR37P _12

43 FastTrace 2X/2E & ift Series 19.7 Genie CCTV WIP13BV 1.3 MP 2 B WIP3BVAF 3 MP 2 B In: NOK Out: NA In: NOK Out: NA I: NOK I: NOK Supported IP Cameras NA XOa Zoom & focus only in web interface XOa fps. Changing event recording resolution and frame rate in XO client may cause temporary NO VIDEO messages. Camera recovers automatically after a few minutes. OSD and privacy mask only via web interface _12 43

44 Supported IP Cameras 19.8 Geovision FastTrace 2X/2E & ift Series GV-BL Full HD 2 B In: ext. mic NOK GV-MFD1501-1F Full HD 2 B In: built-in mic Zoom & focus XOa NOK NA XOa The list above contains only the Geovision cameras that Xtralis has tested and approved according to its own protocols. It is possible (but not guaranteed) that similar Geovision cameras, using the same firmware, also function correctly. It concerns the following camera types: GV-BL120D / 130D / 220D / 320D / GV-BL1200 / 1300 / 1500 / 2400 / 2500 / 3400 / 1210 / 2410 /3410 / 5310 / 2510-E / 5310-E GV-BX1300 Series / 1500 Series / 2400 Series / 2500 Series / 3400 Series / 5300 Series GV-BX1500-E / 2400-E / 3400-E / 5300-E / 2510-E / 5310-E GV-CA120 / 220 and GV-CAW120 / 220 GV-FD120D / 220D / 320D / 1200 / 1500 / 2400 / 2500 / 3400 / 5300 / 1210 / 1510 / 2410 / 2510 / 3410 GV-FE420 / 421 / 520 / 521 / 2301 / 4301 / 2302 / 3402 / 3403 / 5302 / 5303 GV-FER3402 / 3403 / 521 / 5302 / 5303 GV-MDR120 / 220 / 320 / 520 / 1500 Series / 3400 Series / 5300 Series GV-MFD120 / 130 / 220 / 320 / 520 / 1501 Series / 2401 Series / 2501 Series / 3401 Series / 5301 Series GV-PT130D / 220D / 320D GV-UBL1211 / 2411 / 3411 / 1301 Series / 2401 Series / 3401 Series GV-UBX1301 Series / 2301 Series / 3301 Series GV-VD120D / 121D / 122D / 123D / 220D / 221D / 222D / 223D / 320D / 321D / 322D / 323D GV-VD1500 / 2400 / 2500 / 3400 / 1530 / 2430 / 2530 / 3430 / 1540 / 2440 / 2540 / 3440 / 5340 / 2540-E / 5340-E 1 Saving zoom presets is not possible. When using external microphone, enable audio in the camera s web interface _12

45 FastTrace 2X/2E & ift Series 19.9 Grundig Supported IP Cameras GCI-K1577TH 1 Full HD 2 B In: ext. mic NOK NA XOa gr nsx GCI-K1627D 2 HD 2 MP 2 B In: ext. mic NOK NA XOa gr nsx GCI-K1677D 1 Full HD 2 B NA NOK NA XOa gr nsx GCI-K1779P HD 2 MP 2 B In: ext. mic OK XOa gr nsa GCI-M0566F x B In: built-in mic Zoom 4 XO gr nsz 1 OSD and privacy mask only via web interface. 2 At a resolution of 1920 x 1080, only one stream can provide 25 fps. A second 1920 x 1080 stream will only achieve 13 fps. 3 OSD and privacy mask only via web interface. Highest resolution only via web interface. Analytics resolution is 640 x 480 if stream 1 uses highest resolution (shows 720 x 480 in Info bar). Use Back End Software Dewarping" as fisheye setting in the camera. 4 Zoom works in dewarped mode, but the zoom button zooms in. Zoom using mouse works well _12 45

46 Supported IP Cameras IC Realtime FastTrace 2X/2E & ift Series IC-i2t-Px20W- AIOY 1 ZENON-1s- PO2-IXO-x x B NOK 1920 x B NOK 7 x I Yes XOa Yes XOa General 00.3.R, build: General 04.0.R, build: Frame rate is limited to 25 fps. Contrast not working. Iris not working. OSD and privacy mask only via web interface. 1 Privacy mask not available _12

47 FastTrace 2X/2E & ift Series IndigoVision Supported IP Cameras BX520-HD 1920 x B In: ext. mic 7 x I Yes XO Frame rate is limited to 25 fps. Contrast only via web interface. Iris not working. Reposition camera to autofocus. OSD and privacy mask only via web interface _12 47

48 Supported IP Cameras LG FastTrace 2X/2E & ift Series # of video LNB x B In: ext. mic I: NOK Focus only via web interface XOa LND3220R x B NA NA NA XOa LNP3020T HD 2 MP 2 B Audio in NOK OK XOa LNU5110R x B LNV7210R x B In: ext. mic In: ext. mic NOK NOK XOa NOK NOK XOa The list above contains only the LG cameras that Xtralis has tested and approved according to its own protocols. It is possible (but not guaranteed) that similar LG cameras, using the same firmware, also function correctly. It concerns the following camera types: LNB5220 LND7210R LNU7210R LNB7210 LNP2810T LNU7210RH LND3110R LNP3022T LNV5110R LND5110R LNU3110R LNV7210 LND5220R LNU3220R LNV7210RH LND Frame rate is limited to 5 fps. No brightness/contrast/saturation. OSD and privacy mask only via web interface. 2 Frame rate is limited to 7 fps. No brightness/contrast/saturation. OSD and privacy mask only via web interface. 3 Frame rate is limited to 5 fps. OSD and privacy mask only via web interface. 4 Frame rate is limited to 5 fps. OSD only via web interface _12

49 FastTrace 2X/2E & ift Series Moog Supported IP Cameras EXO-HD SD 2 B NOK NOK NA XOa Brightness, contrast, saturation not available. OSD and privacy mask only via web interface _12 49

50 Supported IP Cameras Santec FastTrace 2X/2E & ift Series SNC-211FDIA Full HD 2 B NA NA SNC-6312IRH HD 2 MP 2 B SNC-8322HO HD 2 MP 2 B In: ext. mic In: ext. mic Manual focus 1 XO BW00.8.R, build: Zoom XOa OK XOa OSD and privacy mask only via web interface. 1 Zoom and autofocus only via camera web interface. OSD and privacy mask only via web interface _12

51 FastTrace 2X/2E & ift Series Scati Supported IP Cameras SED-11004N-E 704 x B NOK NOK Yes, autofocus and iris NOK XOa V3.1.6 build This camera uses ONVIF v2.02. This camera also works with the Hikvision driver _12 51

52 Supported IP Cameras Sony FastTrace 2X/2E & ift Series SNC-EB602R 1280 x B NA NA NOK XOa SNC-EM632R Full HD 2 B NA NA Only zoom XOa SNC-XM632 Full HD 2 B In: built-in mic NA NA XOa When using the ONVIF driver, you must enable the 2 nd stream manually, using the camera s web interface. These cameras also work with the Sony driver _12

53 FastTrace 2X/2E & ift Series Vista Supported IP Cameras VK2-1080BIR3V9F 1 HD 2 MP 2 B NA NA Zoom only XOa VK2-1080VRDIR35V16e 2 VK2-1080XIRPTZF x x B NA NA NA XOa B In: ext. mic Yes 4 XOa T4_release T8- release X2_release 1 PTZ: saving presets not possible. 2 Frame rate is limited to 12 fps. OSD and privacy mask only via web interface. 3 Frame rate is limited to 12 fps. OSD only available via web interface. Set camera to CBR (bitrate can go up dramatically with VBR in scenes with a lot of motion.) 4 Focus and iris only available via web interface _12 53

54 Supported IP Cameras Vivotek FastTrace 2X/2E & ift Series # of video IB8367A 1 Full HD 3 D NA NA NA XOa b IB8369 HD 2 MP 2 B NA NA Zoom XOa a IB8369A 1 Full HD 3 D NA NA NA XOa f Maximum delivered frame rate is fps. OSD and privacy mask only via web interface. 1 You must disable "Dynamic intra frame period" in web interface. Analytics image quality is low for visualisation _12

55 FastTrace 2X/2E & ift Series Xeno Supported IP Cameras # of video XIPDC Full HD 2 B NA NA NA XOa Frame rate is limited to 12 fps _12 55

56 Supported IP Cameras FastTrace 2X/2E & ift Series Appendix A: Ronix IP Camera Setup For correct operation with devices, provide the following settings in the Ronix camera web interface: Network configuration H.264 stream RTSP. The following assumptions are made: Default ID = root, password = root. Default network setup: - Camera IP address: Subnet mask: Gateway: Minimum software version 4.00 is required. To set up Ronix IP cameras, proceed as follows: 1. Open the web interface and log on. 2. Choose Network Configuration > Network Configuration, and set up as shown below: 3. Click Apply. 4. Choose Device Configuration > Camera & Motion _12

57 FastTrace 2X/2E & ift Series Supported IP Cameras 5. For Primary Stream: set the Frame Rate to the desired value. 6. For Secondary Stream: - Set the Frame Rate to 3.75 fps or 5 fps. - Set Image Size to 640 x Click Apply. 8. Choose Network Configuration > RTP/RTSP. 9. For Camera 1: set Multicast Address to For Camera 2: set Multicast Address to Click Apply _12 57

58 Supported IP Cameras FastTrace 2X/2E & ift Series _12

59

60 UK and Europe D-A-CH The Americas Middle East Asia Australia and New Zealand A Disclaimer about this document, statements about Intellectual Property, Copyrights, and Liability, as well as a General Warning are available in an earlier section of this document. Doc _12