IOI SD. Release Notes. Firmware Version

Transcription

1 IOI SD Release Notes Firmware Version Ver. 3 March 22, 2017

2 2017 FLIR Systems, Inc. All rights reserved worldwide. Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are used for identification only and are the property of their respective owners. This product is protected by patents, design patents, patents pending, or design patents pending. The contents of this document are subject to change. FLIR Systems, Inc Hollister Ave. Goleta, CA Phone: FLIR ( ) International: For technical assistance, please call us at or visit the Service & Support page at Document History Version Date Comment 3 March 22, 2017 Initial FLIR release 2 IOI SD FW v Release Notes March 22, 2017

3 Table of Contents Table of Contents Version Content Firmware Version Location... 5 Supported Products and Platforms... 7 Key Features PTZ Tracking with Quasar CP x PTZ Camera Binding the TRK-101-P to the PTZ Camera Hand-off from FLIR FC-Series ID Cameras to trk-101/trk-101-p... 9 Known Issues and Limitations in the Current Version Known Issues and Limitations in Version Known Issues and Limitations from Previous Versions Upgrading the Firmware Latitude Compatibility Disclaimer Appendix A.1. Binding the Quasar PTZ Camera to the PTZ Tracker A.2. Binding the FC-Series ID Camera to the trk-101-p A.3. PTZ Camera Installation Guidelines Site Design Considerations PTZ Hand-off Design Considerations Recommendations March 22, 2017 IOI SD FW v Release Notes 3

4 4 IOI SD FW v Release Notes March 22, 2017

5 Version Content Version Content This release supports the key features listed in section 3 for the TRK-101-P PTZ Tracker for Quasar 30x PTZ camera only. In addition to documenting the Key Features, these release notes cover Supported Products and Platforms, Known Issues and Limitations in the Current Version, Known Issues and Limitations in Version , Known Issues and Limitations from Previous Versions, Upgrading the TRK-101-P Firmware, and Latitude Compatibility. Caution: This firmware should not be installed on units that do not support SoE (units shipped with firmware lower than version 2.1.1). If such a unit is upgraded with this firmware version, the Analytic Decoder mode of the IOI IP functionality will not operate. In this case, the unit will operate only in Analog mode 1.1 Firmware Version Location This firmware version is available from here. March 22, 2017 IOI SD FW v Release Notes 5

6 6 IOI SD FW v Release Notes March 22, 2017

7 Supported Products and Platforms Supported Products and Platforms This version is applicable to the following products: Product Name TRK-101-P PTZ Tracker Quasar CP x PTZ Camera FLIR FC-Series ID camera Latitude 7.0 Update and higher DNA 1.0 or higher Description Encoder with built-in PTZ video analytics and H.264 compression. PTZ binding of the Quasar CP x is supported only by Latitude when operated in Decoder mode. Special Quasar PTZ camera hardware (Rev.2 and Rev. 3) with firmware that supports the PTZ Tracker. Thermal fixed camera with built-in video analytics, V2.02 and above Update that supports binding the Quasar CP x camera with TRK-101-P. DNA version or higher. Click here to download the latest DNA Release Notes. Click here to download the latest DNA User Manual. March 22, 2017 IOI SD FW v Release Notes 7

8 8 IOI SD FW v Release Notes March 22, 2017

9 Key Features Key Features Version includes the following key features: 3.1 PTZ Tracking with Quasar CP x PTZ Camera This firmware version supports PTZ Tracking on a Quasar CP /301 PTZ camera manufactured with the hardware indicated in the Supported Products and Platforms section. The PTZ camera hardware version must be Hardware Rev 2 or Rev 3 in order to support PTZ tracking. These cameras were shipped from FLIR after November 1, Note: Units produced after November 2014 include PTZ Head module number ITN-2. The module version number (CEA10) is displayed in the camera s System > Firmware Version screen. The firmware on units with this PTZ head should not be upgraded. To verify that the hardware supports PTZ tracking Open the CP x System > View Information > Parameters screen. In the Mega Pixel Camera Initial Configuration File > Hardware section, verify that Version = <Rev 02> or <Rev 03>. The firmware version also operates with Quasar cameras with Hardware Rev 1 that do not support PTZ Tracking. When selecting the camera model from the Camera > Type & Model screen, select the camera model indicated with IT on preset. 3.2 Binding the TRK-101-P to the PTZ Camera The PTZ tracking function is implemented by binding the trk-101-p PTZ Tracker to the Quasar CP x camera in the Latitude VMS system. See the Appendix for instructions how to bind the PTZ Tracker to the Quasar PTZ camera. 3.3 Hand-off from FLIR FC-Series ID Cameras to trk-101/trk-101-p In addition to supporting hand-off from ioi HD cameras, trk-101-p now supports hand-off from FLIR FC-Series ID cameras to trk-101-p. Cameras must have version 2.02 and above. See the Appendix for instructions how to bind the PTZ Tracker to the FC-Series ID camera. Note: The FC-ID camera is discovered automatically only if: The camera and trk-101-p are configured on the same VLAN on the trk-101-p PTZ Setup > PTZ Synchronization screen, and The FC-Series ID camera IP address is configured to port In the Add Manually text box, enter <IP address>:port (for example :8084). March 22, 2017 IOI SD FW v Release Notes 9

10 10 IOI SD FW v Release Notes March 22, 2017

11 Known Issues and Limitations in the Current Version Known Issues and Limitations in the Current Version Note: This version does not support Backup & Restore from IOI HD cameras to/from the TRK-101/ TRK-101-P. Firmware versions that support this function are available from FLIR TCX. The following table includes known issues and limitations reported since GA version that are still open: BUG ID TYPE SUMMARY COMMENTS Bug Bug Limitation Limitation The batch Solo Setup recording is not working on units in Decoder mode. On the Camera > Type & Model screen > the Image Quality Enhancer the error message should be changed to mention IP Mode. TRK-101-P & Latitude > When binding a unit, the user does not receive a warning message that it is not possible to add new Presets in Latitude. TRK-101-P & CP > only VGA resolution is supported. Bosch cameras > When selecting Digital input, digital analytics output over IP mode, the video output quality from the camera is worse than when viewed with the VLC media player. When operating in DVR mode with Enhanced detection enabled, after clicking the ARM button, the unit reboots after defining depth. Latitude > System Settings > Alarm types > Action > Units that are bound with activated alarms (analytics have been cleared) are not displayed as available. When handing off the camera to a PTZ camera, if the ioi-hd streaming is on MJPEG, the video is not displayed on the TRK-101-P. When the auto depth calculation is run in modes other than NVR or decoder modes, the GUI indicates that the unit is rebooting. FLIR FC-ID > The automatic discovery feature works only on port We recommend using auto calibration. Works as designed. Configure presets from the TRK unit. Bind the units in Latitude and select Decoder mode on the TRK unit. This automatically sets camera and TRK settings. Changing the setup is supported only on H.264. If the port was changed on the FC-ID camera, add the unit manually in the TRK unit. March 22, 2017 IOI SD FW v Release Notes 11

12 Known Issues and Limitations in the Current Version BUG ID TYPE SUMMARY COMMENTS Limitation Limitation FLIR FC-ID > When handing off to a PTZ camera from the FC-ID camera, the Last detection object feature does not work on the FC-ID camera. Camera > Type & Model > It is not possible to save the parameters of the manual Image Quality Enhancer, including when in NVR mode. Hikvision and Bosch> The TRK cannot decode the stream from the camera. FLIR DNZ PTZ camera > The TRK cannot decode the stream from the FLIR DNZ unit (SVC parameter does not exist on the new firmware). On IE9, the System > User Accounts screen is not accessible. FC-Series ID camera with trk-101 > The trk-101 cannot decode the video stream when changing the resolution in Digital mode CP x > Changing video format between NTSC and PAL causes the camera to move slowly. Use the previous DNZ firmware and use Analog mode in the TRK unit. We recommend using IE 10 or 11. Reboot the camera or trk-101. Reset Quasar unit Latitude > User can overwrite an existing preset. Use TRK web interface Limitation Latitude > Auto Rearm can cause TRK to be armed and therefore cannot stream video while configuring the TRK. Before set up from the TRK web interface, tile must be closed in Control Center and make sure the unit is armed from UVMS TRK-101-P > PTZ > The Apply button remains grayed out when changing communication protocol settings. When trying to define an event with PTZ action, a popup message of "You can't define this action..." appears although the camera is a PTZ camera. Disarm event does not work on TRK-101-P if configured as PTZ camera. Set the Camera Type as Fixed and then reset as PTZ. Define Camera model and communication again. Wait a few seconds after going to Setup page and before entering the Events page or refresh the Events page. 12 IOI SD FW v Release Notes March 22, 2017

13 Known Issues and Limitations in Version Known Issues and Limitations in Version The following table includes known issues and limitations in the previous GA version ( ) that are still open: BUG ID TYPE SUMMARY COMMENTS Limitation Limitation Limitation Latitude > Presets > Quasar CP & TRK-101-P > When clicking a Preset, after a while Latitude configures the camera as Preset 1. Latitude > Bosch > It is not possible to bind the camera to the TRK-101-P in Decoder mode. TRK-101-P > A fixed camera should be disarmed and in decoder mode when defining PTZ hand-off. Works as designed. Use Manual RTSP mode. Disarm the fixed camera before setting up the hand-off. March 22, 2017 IOI SD FW v Release Notes 13

14 14 IOI SD FW v Release Notes March 22, 2017

15 Known Issues and Limitations from Previous Versions Known Issues and Limitations from Previous Versions The following table includes known issues and limitations in firmware versions prior to that are still open: BUG ID TYPE SUMMARY COMMENTS Limitation Bug Bug Bug Limitation Use a bit rate 900 or higher with D1 resolution when a rule is defined on a static object. IOI - web > The user has to run IE10/11 as administrator for the Solo setup files to be created and saved on Windows 8 & 8.1. Depth > Solo Setup >The close-up view window always returns back to the left upper side of the picture when the solo setup clip running. A custom direction arrow is displayed on a Loitering rule when changing the rule from IT to Loitering. Latitude > FLIR T4350BN > Camera > Video > Sub Stream > Use VGA resolution with TRK analytics Limitation The unit did not send on events to Gmail Limitation Limitation Limitation Limitation FLIR PT-Series > Pelco > RS-485 serial control interfaces commands are opposite (moves up instead of down). FLIR Fixed family > TRK-101-P > Uncheck the Enable PTZ functionality checkbox in Latitude before binding the camera. In Decoder mode, when the unit is powered on, the unit does not display its IP address in the analog video output. TRK-101-P > After binding, when binding a PTZ camera from Latitude, the Analytics tab is not displayed in the web interface sidebar after setting presets. Use Exchange or Yahoo Mail. In the PT camera Setup > Maintenance screen, set Sensor- >Communications- >Serial Remote->Serial Remote 1 Pilot Mode to "No", save, and restart the server. See Appendix. Refresh the page after setting presets. March 22, 2017 IOI SD FW v Release Notes 15

16 Known Issues and Limitations from Previous Versions The following table includes known issues and limitations in firmware version , reported after version that are still open: BUG ID TYPE SUMMARY COMMENTS Limitation Site Viewer > There was no audio alert for the x units. The video flickers in the web interface when the user scrolls down using Windows 8.1 and Bug Windows Bug Bug Limitation Limitation Bug Bug Bug A recording on the Site Playback page in MPEG-4 and H.264 did not play correctly. The 64-bit version of VLC cannot be installed and used by Site Playback. There is no option to play a clip on a full screen on the Site Playback page in the web interface. It is not possible to sync the encoder when it is armed and set as a PTZ camera in Analog, DVR and Decoder modes, because there is no video stream. Only IOI units that support SOE recording are listed in the Units drop-down list on the web interface in the Events > Responses page, including units that are added manually. When selecting an IOI-controlled PTZ camera in Latitude, Meridian, and Horizon, the PTZ protocol type is listed as IOImage PTZ instead of IOI PTZ Tracker. The audio alert did not function on the Site-Live page upon detection of an event. This is supported on units with version & Disarm the unit from which you are playing the clip. The units require IE 32-bit browsers. Install the 32- bit VLC version. Disarm the fixed camera, sync the unit, and rearm the fixed camera. Select this setting (default) for an IOI encoder set up as a PTZ camera. The following table includes known issues and limitations in firmware version , reported after version that are still open: BUG ID TYPE SUMMARY COMMENTS Limitation The noise reduction function does not operate properly on MJPEG Limitation It was not possible to install ActiveX on 64-bit versions of Internet Explorer 9. Use IE Limitation Web video rendering is supported only on display adapters that fully support Direct X (e.g., NVidia, ATI, and most Intel onboard adapters). 16 IOI SD FW v Release Notes March 22, 2017

17 Upgrading the Firmware Upgrading the Firmware Units with firmware version lower than version can be updated over the web or by using the Discovery Network Assistant (DNA) tool. Note: From the encoder s Setup > Camera > Streaming screen, select the upgrade file according to the camera s Video Standard (PAL or NTSC). To upgrade the firmware Open the Setup > System > Firmware screen. Browse for the firmware file in the directory to which you saved the file. Press Upgrade. Caution: This firmware should not be installed on units that do not support SoE (units shipped with firmware lower than version 2.1.1). If such a unit is upgraded with this firmware version, the Analytic Decoder mode of the IOI IP functionality will not operate. In this case, the unit will operate only in Analog mode March 22, 2017 IOI SD FW v Release Notes 17

18 18 IOI SD FW v Release Notes March 22, 2017

19 Latitude Compatibility Latitude Compatibility Support for TRK-101-P with PTZ tracking on Quasar CP x is available only with Latitude VMS Refer to Latitude documentation for the upgrade procedure. March 22, 2017 IOI SD FW v Release Notes 19

20 20 IOI SD FW v Release Notes March 22, 2017

21 Disclaimer Disclaimer By providing this document, FLIR Systems, Inc. is not making any representations regarding the correctness or completeness of its contents and reserves the right to alter this document at any time without notice. FLIR Systems, Inc All rights reserved. March 22, 2017 IOI SD FW v Release Notes 21

22 22 IOI SD FW v Release Notes March 22, 2017

23 Appendix Appendix The Quasar PTZ camera and the TRK-101-P are bound to each other from the Latitude AdminCenter. To bind the TRK-101-P to the camera 1. Open the Latitude AdminCenter on the desired site. Make sure that the PTZ Tracker is listed in the site. 2. Select the Analytics tab. Figure 1: Latitude Analytics Tab 3. Select the camera that you want to bind from the Available Cameras list. 4. Use the arrow button to add it to the Camera table. Caution: Make sure that the TRK unit is not attached to Latitude. 5. In the table, do the following: In the Connection Type column, from the drop-down list, select Decoder for the CP x PTZ camera In the Analytic Device IP column, enter the IP address of the TRK unit that you want to attach to the PTZ camera. 6. Set the Rearm Time in the Auto Rearm column. This is the number of seconds until the camera is rearmed after being automatically disarmed due to manual PTZ control. The Rearm countdown starts from the moment the camera tile is deselected in ControlCenter. The default is 30 seconds. 7. Click Save. 8. On the PTZ Tracker, configure the TRK encoder presets. 9. Then configure Depth and Rule settings for each preset on the PTZ Tracker. 10. Arm the camera from the web interface or from Latitude. March 22, 2017 IOI SD FW v Release Notes 23

24 Appendix In order to implement a hand-off of from the FC-Series ID camera to a PTZ camera, the FC-Series ID camera and PTZ Tracker (trk-101-p) are bound together from the web interface of both units. Note: 1. Before starting the procedure below, wait until the calibration of the FC-Series ID camera reaches 100% on the Live Video page. 2. Disarm the analytics by clicking the Analytics Disable icon on the FC-Series ID Live Video page. On the FC-Series ID Camera 1. Select Maintenance > Sensor > VMS Remote. 2. Click + (Plus). 24 IOI SD FW v Release Notes March 22, 2017

25 Appendix 3. From the drop-down list, select IOI Interface. 4. Click Create. 5. Shut down the server by pressing the green button next to Server Running. The message Server Stopped is now displayed on-screen and in an information box. 6. Click Accept. The server restarts. 7. Set the depth on the Setup > Analytics screen. 8. From the Calibration Mode drop-down list, select Auto or Manual. Wait one minute after the process reaches 100%. March 22, 2017 IOI SD FW v Release Notes 25

26 Appendix On the trk-101-p 1. From the Camera > Type & Model screen, verify that the Camera Model is configured as PTZ. 2. Click Start PTZ Setup. 3. On the Detection and Tracking screen, select Detection from another camera with Automatic PTZ tracking. 4. Click Next. 5. Click Calibrate and follow the instructions on the web interface. 6. Click Next. 7. From the PTZ Setup > PTZ Synchronization screen, follow the procedure described in the HTML Edition Units User Guide which can be downloaded from here. Refer to Step 3: PTZ Synchronization with Fixed Cameras in the section Using the PTZ Camera Definition Wizard. If the camera and encoder are located on the same VLAN, the camera s IP address is displayed automatically in the IP address text box. If the FC-Series ID camera is located on a different VLAN than the trk-101-p, or if its IP address has changed, you must add the FC-Series ID camera manually in the Fixed Camera Selection section of the trk-101 PTZ Synchronization screen. In the IP Address text box, set the HTTP port to 8084, where the IP address is <IP address>:port (for example :8084). 8. After binding the units, set 8 correlation points on the ground, as described in the procedure To set correlation points in a preset in the User Guide. 9. You can set a few presets for each fixed camera. The PTZ camera will automatically go the relevant preset according to the intrusion location on the fixed camera. 26 IOI SD FW v Release Notes March 22, 2017

27 Appendix Following are some guidelines to follow when installing the Quasar PTZ camera. Site Design Considerations Minimum camera mounting height: 6m/20 feet Object size: 10%-20% of the scene Minimal tracking angle: 10 relative to the pole Maximal tracking angle: less than 90 relative to the pole PTZ tracking can be initiated by detection on presets, hand-off from a fixed camera, or clicking on the object (Click-and-Track) once this feature is released in United VMS. Note that it is not possible to configure the camera for hand-off from a fixed camera and detection on presets at the same time. PTZ Hand-off Design Considerations When bound to a Quasar PTZ camera, the system can support up to 31 presets. Hand-off can be configured from presets from multiple fixed cameras (see Figure 1) or multiple presets per fixed camera (see Figure 2) to arrive at a total of 31 presets on the PTZ camera. Figure 2: Multiple PTZ presets and fixed cameras March 22, 2017 IOI SD FW v Release Notes 27

28 Appendix Recommendations Figure 3: Multiple PTZ presets with one fixed camera The recommended camera mounting height is a by-product of many considerations. As a guideline, it should not be too high or too low. The higher the camera, the sharper the angle that the camera requires in order to see the ground and objects. This creates more depth in the scene. Mounting the camera too high is not recommended, because objects should occupy 10%-20% of the frame when using analytic presets. Mounting the camera too high requires a lot of zoom when using presets. It is recommended to use the default object size (49) or a setting within the range of on the PTZ Setup > Tracking Parameters screen. Camera height should be measured relative to the scene plane. Users who are not professional installers should set the height to Unknown in the camera s web interface in order to allow the algorithm to calculate the mounting height. The horizon should be parallel to the X axis of the camera surface. The camera should be installed without any roll angle (variation from 180 along the longitude) or the minimal roll angle possible. After completing the depth configuration, verify that the horizon line (percentage of the camera FOV) was calculated properly. It is recommended that the horizon does not exceed 30% of the FOV, meaning that the scene occupies maximum 70% of the frame. 28 IOI SD FW v Release Notes March 22, 2017

29 Appendix Example 1: Good Detection and Tracking Area Most of the FOV is not hidden. This is an effective tracking zone. A human in this area will occupy 10%-20% of the scene. Both X and Y axes occupy approximately 2/3 of the FOV. Low Detection Area Most of the FOV is hidden. The tracking zone is not efficient. A human in this area will not be within 10%-20% of the scene. Note: Detection and Tracking at this area is limited to the Y axis, because there are many hidden objects on the X axis. Minimal Object Size 10% of the frame for detection and tracking. Maximal Object Size 20% of the frame for detection and tracking. No Tracking Area Camera will require an angle that is too sharp to track the object. Not relevant area This second plane is not relevant for detection but it occupies a large portion of the FOV. Camera height ~ 6m/20 feet March 22, 2017 IOI SD FW v Release Notes 29

30 Appendix Example 2: Good Detection and Tracking Area Most of the FOV is not hidden. This is an effective tracking zone. A human in this area will occupy 10%-20% of the scene. Low Detection Area Most of the FOV is hidden. The tracking zone is not efficient. A human in this area will not be within 10%-20% of the scene. Note: Detection and Tracking at this area is limited to the Y axis, because there are many hidden objects on the X axis. Minimal Object Size 10% of the frame for detection and tracking. Maximal Object Size 20% of the frame for detection and tracking. Not relevant area Heavy traffic to the right of the FOV will trigger false alarms. This can be avoided by creating rules. The building on the left occupies a large portion of the FOV. Cars and trees obscure the ground. Camera height ~ 22m/72 feet 30 IOI SD FW v Release Notes March 22, 2017

31 Appendix Example 3: Good Detection & Tracking Area Most of the FOV is not hidden. This is an effective tracking zone. A human in this area will occupy 10%-20% of the scene. Minimal hidden objects in the scene. Low Detection Area This area overlaps with the green area (and appears as orange below) because a detected object will be properly tracked in this area. A human in this area will not be within 10%-20% of the scene. Minimal Object Size 10% of the frame for detection and tracking. Maximal Object Size 20% of the frame for detection and tracking. Not relevant area Heavy traffic in the upper right area of the FOV will trigger false alarms. This can be avoided by creating rules. Building in the upper left area of the FOV occupies a portion of the FOV. Camera height ~7m/23 feet Good installation March 22, 2017 IOI SD FW v Release Notes 31

32 FLIR Systems, Inc Hollister Ave Goleta, CA USA PH: PH: (Sales) PH: (Support) FX: Corporate Headquarters FLIR Systems, Inc SW Parkway Ave. Wilsonville, OR USA PH: FX: Document: IOI SD FW v Release Notes Version: 3 Date: March 22, 2017 Language: en-us