UDC 360 UNDER DOOR 4-CAMERA SYSTEM

Transcription

1 UDC 360 UNDER DOOR 4-CAMERA SYSTEM TACTICAL ELECTRONICS Products OPERATION AND SUPPORT PUBLICATION PROPRIETARY TACTICALELECTRONICS.COM PRODUCTS / EOD TRAINING / R & D / AVIATION DESIGN / ENGINEERING / MANUFACTURING HEMLOCK FACILITY 2200 NORTH HEMLOCK AVE / BROKEN ARROW, OK / V: / V: / F: CRUSADER FACILITY 2844 CRUSADER CIRCLE / #100 / VIRGINIA BEACH, VA / V: / F:

2 PROPRIETARY 2

3 3 UDC 360 UNDER DOOR 4-CAMERA SYSTEM Manual Contents Kit Identification Power-up Operation Monitoring Options Specifications

4 UDC 360 KIT IDENTIFICATION 4 One) Under Door Camera 360 (4-camera system) Four cameras: forward, upward, left, and right facing cameras Internal mini DVR with SD card recording capabilities 16GB SD card Four lux black & white CCD chip at the distal end of insertion panel Insertion Panel only thick IR LED illuminator (1) for flood illumination 2400 mhz transmitter onboard One) Telescoping deployment pole One) Hard-wire cable (with inclusion of Handheld Monitor Pro) Used for hard-wire operation with Handheld Monitor Pro One) Monitoring option of your choice (Wrist Monitor Pro or Handheld Monitor Pro) Handheld Monitor Pro has a 5.0 screen Wrist Mounted Monitor Pro gives the operator a 3.5 screen on the arm One) Storm Case w/ precision cut foam for stable storage environment Unbreakable Watertight Airtight Corrosion Proof

5 UDC 360 POWER UP 5 The UDC 360 Under Door Camera is powered by four 3Volt Photo Lithium batteries. Most manufacturers of these cells designate them as size 123 or CR123A. Tactical Electronics systems draw high current; use only GE SANYO, ENERGIZER, or DURACELL batteries. Testing has proven those batteries to provide the longest run time in our products. Run times will vary, components in this system are designed to optimize power management and power sharing when hard-wired together. Usage of IR LEDs will also contribute to varied run times. The diagrams below demonstrate proper battery installation and power-up for the UDC 360 Under Door Camera. Battery Compartment & Power-Up Procedure: The UDC 360 (left) requires four 3V Lithium batteries for operation. Use the battery orientation diagram adhered to the UDC 360 for reference. NOTE: For SD card recording, ensure the SD card is inserted before powering ON the UDC 360. * Always remove batteries when not in use The power switch for the UDC 360 is a push button located on the side of the unit. The picture (left) identifies the UDC 360 power button. Fully depress the power button to power ON and OFF the UDC 360. Immediately after the UDC 360 is powered ON the LED indicator will illuminate a solid blue for approximately 8-10 seconds while the system initializes. Once the power-up phase is complete the LED indicator will illuminate a solid green indicating full operational use (If no SD card is inserted, the LED indicator will flash red). LED indicators NOTE: When the UDC 360 is powered ON all IR LEDS are powered OFF by default. To power OFF the UDC 360, hold down the power button for 3 seconds to begin power down cycle - when the LED illuminates blue release the power button and the unit will power OFF within 5 seconds. NOTE: DO NOT open the battery door before powering OFF the UDC 360. Failure to properly power OFF the unit will result in loss of recorded files. Battery Life Indicator: The LED power indicator will flash red and green to indicate low battery power. As battery life continues to diminish the LED indicator will illuminate solid red. After the LED illuminates solid red the unit will shut down within 10 minutes. When battery life is critical the LED indicator will illuminate solid blue. Once this occurs the UDC 360 will only remain ON for seconds while the system shuts down to protect recorded video on the SD card.

6 UDC 360 OPERATION 6 Operation: The UDC 360 Under Door Camera is shown (left) in proper operating position on a flat surface as if it were being slid under a door. Insertion Panel: The distal tip of the UDC 360 houses both the forward and upward camera lenses, the IR flood illuminator, and the microphone. The lux camera chip is located in the tip of the insertion panel and slides into the room when the panel is placed underneath a door. The unit's IR flood illuminator is mounted on the insertion panel for enhanced viewing in low-light situations. IR LED Modes: The UDC 360 provides two stages of IR illumination. By default IR flood illuminator is powered OFF upon every power up of the UDC 360. To power ON the IR flood illuminator depress the "IR" button (shown left). The current state of the IR flood illuminator will be displayed on the monitor screen. Remote toggle of IR flood illuminator: Depress the "IR" button on the Wrist Mounted Monitor Pro or the Handheld Monitor Pro to remotely turn OFF and ON the IR flood illuminator. NOTE: Use of the IR LEDs directly affects the battery life of the unit. NOTE: The UDC 360 body will become quite warm during use, especially while using the IR flood illuminator is ON. This is normal.

7 UDC 360 OPERATION 7 Wireless Transmission: Wireless operation of the UDC 360 is very simple. Follow proper UDC 360 power-up procedure and the unit will automatically transmit wireless video signals. Once the UDC 360 is powered ON, the unit immediately begins transmission of an RF video signal. When a monitor is powered ON the monitor begins receiving the video signal from the UDC 360. Cycle through the channels on the monitor until a picture is displayed. Wrist Mounted Monitor Pro Hard-Wire Transmission: The 0.25 inch jack (shown left) is used for hard-wire operation between the UDC 360 and the Handheld Monitor. Simply power ON both the UDC 360 and Handheld Monitor, then insert the male/male cable into the 0.25in jacks on each unit. Hard-wire operation disables the wireless signal. 0.25in jack Channel Selector: To determine which channel the UDC 360 is transmitting, simply power ON both the UDC 360 and monitor. Use the channel selector button(s) on the monitor to cycle through each channel until a picture is displayed on screen. Shown left is the UDC 360 Outgoing Channel selector. Outgoing channel selector The UDC 360 will only transmit on channels 1-4. If a channel outside this range is selected the UDC 360 will not transmit. Hard-wire, recording, and IR LED functionality will remain operational.

8 UDC 360 OPERATION 8 Quad View Camera Selection: The UDC Camera System contains four light sensitive B/W cameras that provide forward, upward, left, and right camera views. The forward camera angle provides a forward view of a room's interior. The upward camera angle provides a view of the interior side of a door. The left and right camera angles provide left and right views of a room's interior. All four cameras are housed within the unit's insertion panel. Manual toggle of camera views: Depress the "Camera" button (located on the side of the UDC 360) to manually toggle between the forward, upward, left, and right camera views. Remote toggle of camera views: Depress the "Camera" button on the Wrist Mounted Monitor Pro or the Handheld Monitor Pro to remotely toggle between forward, upward, left, and right camera views. Remote toggle of IR flood illuminator: Depress the "IR" button on the Wirst Mounted Monitor Pro or the Handheld Monitor Pro to remotely turn OFF and ON the IR flood illuminator. Wrist Mounted Monitor Pro Telescoping Push Pole Attachment: The UDC 360 supports a Telescoping Push Pole. The Push Pole is designed with a magnetic ball attachment, located at the end of the pole. To attach the Push Pole to the UDC 360 simply place the magnetic ball onto the mount located on top of the UDC 360. Once the Push Pole is attached the user is capable of placing the UDC 360 on target and maneuver via the Push Pole. Push Pole attachment To detach the Push Pole from the UDC 360, rotate the pole until the steal pin at the end of the pole pushes away from the unit and releases from the magnetic mount.

9 UDC 360 OPERATION 9 SD Card Recording: Insert the SD card into the SD card slot with the UDC 360 powered OFF. DO NOT insert or eject the SD card with the UDC 360 powered ON; otherwise, recorded video files will not finalize and will become corrupted. Immediately after the UDC 360 is powered ON, the LED indicator will illuminate a solid blue for approximately 2-5 seconds while the system initializes. Once the power-up phase is complete the LED indicator will illuminate a solid green indicating operational use and proper SD card recording. If the UDC 360 system indicates a recording error, REC ERROR will display on the monitor(s) in use. If REC ERROR is displayed, power OFF the UDC 360, reinsert the SD card, and power ON the unit. The UDC 360 will transmit video without the use of SD card recording. If the unit is powered ON without an SD card inserted "REC ERROR" will be displayed on the monitor(s) in use. The LED indicator on the UDC 360 will also flash red to indicate no SD card present. SD Card Viewing: * Push in SD Card to eject To review recorded video files: Power OFF the UDC 360, eject the SD card, and insert the SD card into an SD card reader on a computer. All files will be under the folder DCIM\100Media on the SD card. Recorded files will be listed sequentially in numerical order. All recorded video files are AVI files, and are easily viewed in Windows Media Player or VideoLan's VLC Player. AVI files may also be viewed in QuickTime with the appropriate plug-in. Audio: The UDC 360 houses an omnidirectional microphone and records audio and video directly to the SD card for post operational review. microphone

10 MONITOR OPTIONS 10 Tactical Electronics video systems are designed to operate interchangeably with each wireless monitor: Wrist Mounted Monitor (WMM), Handheld Monitor (HHM), Monocular Micro Viewer (MMV), Heads-Up Display (HUD), Wrist Mounted Monitor Pro (WMM Pro), or Handheld Monitor Pro (HHM Pro). Each monitor is programmed to receive a frequency transmitted directly from the purchased camera system. If multiple camera systems are in use, the monitors are equipped to receive separate channel frequencies in order to view and cycle between various Tactical Electronics camera systems. Wrist Mounted Monitor (WMM) The Wrist Mounted Monitor is powered by two 3V Lithium batteries. The batteries are to be inserted positive (+) terminal first. The power switch for the Wrist Mounted Monitor (left) is the top button near the battery cap. Press and hold the power button for approximately 3 seconds to power ON the WMM. The screen will display the current channel and battery power meter when the unit is ON. Always remove batteries when not in use. IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES. Power WMM Operation The Wrist Mounted Monitor has a 3.5 inch LCD screen that displays B/W or color video transmitted from the camera source. The monitor contains an internal receiver, and when powered ON automatically receives RF video signals from the chosen camera. The WMM is completely wireless and cannot be hardwired. WMM Channel Selection If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. Channel Selector To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen.

11 MONITOR OPTIONS 11 Handheld Monitor (HHM) The Handheld Monitor (HHM) is powered by four 3V Lithium batteries, AC, or vehicle power via cigarette lighter plug. The 3V Lithium batteries that are to be inserted negative ( - ) terminal first. The power switch for the Handheld Monitor (left) is a rocker type. The green LED is illuminated when the unit is ON. Always remove batteries when not in use. IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES. HHM Operation Power The Handheld Monitor has a 5.0" LCD screen that displays B/W or color video transmitted directly from the camera source. It has a built-in receiver and when powered ON automatically receives an RF video signal until a hard-wire is plugged in or the HHM is powered OFF. HHM Channel Selection Channel Selector If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture. Hard wire jack Hard-wire Connection The Handheld monitor provides a direct hard-wire connection to compatible camera systems. NOTE: When working in extreme low light environments hardwire the Handheld Monitor to the camera system (if hardwire option is available with the camera system). A hard-wire connection provides a slightly brighter picture on the Handheld Monitor that will be beneficial for low light situations.

12 MONITOR OPTIONS 12 Monocular Micro Viewer (MMV) The MMV is powered by one 3V Lithium battery. Unscrew the battery cap [shown left] to insert the battery. The 3V Lithium battery is to be inserted according to the battery orientation diagram on the MMV. Always remove batteries when not in use. battery cap The power button for the MMV (left) is a rubber push button on the side of the unit. The LED indicator will illuminate green and the video display will slightly illuminate when the unit is powered ON. NOTE: The On Screen Display (OSD) will show a flashing battery icon when the battery is close to critically low levels. LED Indicator POWER The LED will momentarily light up blue when the unit is first powered on, then will illuminate solid green. The LED will illuminate blue whenever the channel button is pressed. The LED will momentarily illuminate red when the unit is powering down. The LED will illuminate solid red when the battery is low. Automatic Shutdown To preserve battery life the MMV will automatically shut off if the unit is idle for approximately 90 seconds. When the unit is nearing automatic shutdown the OSD will show a series of disappearing dots as a countdown timer. To prevent automatic shutoff: Press the channel button once to reset shutdown timer, allowing another 90 seconds of video display. A single press of the channel button will also display the current channel the MMV is receiving. Wireless Video The MMV has a built-in receiver, and when powered ON automatically receives RF video signals from the chosen camera. The MMV is completely wireless and cannot be hard-wired. channel selector If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Any time the channel is changed on the MMV the shutdown timer is reset. Since the initial press of the channel button resets the shutdown timer and displays the current channel, it is necessary to press the channel button more than once to change channels.

13 MONITOR OPTIONS 13 Heads-Up Display (HUD) The Heads-Up Display is powered by two 3V Lithium batteries, The 3V Lithium batteries are to be inserted positive ( + ) terminal first. Always remove batteries when not in use. The power switch for the Heads-Up Display (left) is a rubber push button on the front of the unit. The display slightly illuminates when the HUD is powered ON. To power OFF the HUD press and hold the power button. A red LED in the left eyepiece will illuminate momentarily, indicating the unit is ready to power down. Release the power button. NOTE: The On Screen Display (OSD) will show a flashing battery icon when the battery is close to critically low levels. HUD Operation POWER The Heads-Up Display gives the operator the appearance of a 35-inch screen at a 7 foot distance. The HUD displays B/W or color video transmitted directly from the camera source. channel selector It has a built-in receiver, and when powered ON automatically receives RF video signals from the chosen camera. The HUD is completely wireless and cannot be hard-wired. HUD Mounting The HUD comes standard with the Wilcox 14001G01 Wilcox NVG Mounting Shoe. This mounting shoe is compatible with most Wilcox NVG Mounting Systems. To mount the HUD to the Wilcox NVG Mount, slide the attached mounting shoe into the appropriate slot on the NVG Mount until the HUD system clicks solidly into place. Detach the HUD from the NVG Mount using the release mechanism on the NVG Mount. HUD Channel Selection If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. Note: The first press of the channel selector button will display which channel the HUD is receiving as well as current battery power. To change the channel press the channel selector button again within three seconds.

14 PRO MONITOR OPTIONS 14 Wrist Mounted Monitor Pro (WMM Pro) The Wrist Mounted Monitor Pro is powered by two 3V Lithium batteries. The batteries are to be inserted positive (+) terminal first. The power switch for the WMM Pro (left) is the top button near the battery cap. Press and hold the power button for approximately 3 seconds to power ON the monitor. The screen will display the current channel and battery power meter when the unit is ON. Always remove batteries when not in use. IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES. Power WMM Pro Operation The WMM Pro has a 3.5 inch LCD screen that displays B/W or color video transmitted from the camera source. The monitor contains an internal receiver, and when powered ON automatically receives RF video signals from the chosen camera. The WMM Pro is completely wireless and cannot be hard-wired. Remote Toggle If the camera system in operation is capable of remote toggling follow the instructions below to toggle between camera views and/or IR LED illumination modes. Camera Toggle IR Toggle Remote toggle camera views: Depress the Camera button on the Wrist Mounted Monitor Pro to remotely toggle between separate camera views. Remote toggle of IR illumination: Depress the IR button on the Wrist Mounted Monitor Pro to remotely toggle through IR LED illumination modes. WMM Pro Channel Selection Channel Selector If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When cycling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture.

15 PRO MONITOR OPTIONS 15 Handheld Monitor Pro (HHM Pro) The Handheld Monitor Pro (HHM Pro) is powered by four 3V Lithium batteries, AC, or vehicle power via cigarette lighter plug. The 3V Lithium batteries that are to be inserted negative ( - ) terminal first. The power switch for the HHM Pro (left) is a rocker type. The green LED is illuminated when the monitor is ON. Always remove batteries when not in use. IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES. The monitor contains an internal receiver and when powered ON automatically receives an RF video signal until a hardwire is plugged in or the HHM Pro is powered OFF. Remote Toggle Power IR Toggle Camera Toggle If the camera system in operation is capable of remote toggling follow the instructions below to toggle between camera views and/or IR LED illumination modes. Remote toggle camera views: Depress the Camera button on the Handheld Monitor Pro to remotely toggle between separate camera views. Remote toggle of IR illumination: Depress the IR button on the Handheld Monitor Pro to remotely toggle through IR LED illumination modes. HHM Channel Selection Channel Selector Hard wire jack If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When cycling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture. Hard-wire Connection The Handheld Monitor Pro provides a direct hard-wire connection to compatible camera systems. NOTE: When working in extreme low light environments hard-wire the HHM Pro to the camera system (if hard-wire option is available with the camera system). A hard-wire connection provides a slightly brighter picture on the monitor that will be beneficial for low light situations.

16 SPECIFICATIONS 16 SPECIFICATIONS CAMERAS: WEIGHT: DIMENSIONS (L X W X H): POWER SUPPLY: RUNTIME: HOUSING MATERIAL: OPERATING TEMPERATURE RANGE: FREQUENCY RANGE: TRANSMISSION DISTANCE: COMPATIBLE MONITORS: CAMERA RESOLUTION: CAMERA LIGHT SENSITIVITY: CAMERA SENSOR TYPE: ILLUMINATION: INSERTION PANEL: PANEL LENGTH: HARD-WIRE VIDEO OUTPUT: FIELD OF VIEW: FORWARD CAMERA FIELD OF VIEW: UPWARD CAMERA FIELD OF VIEW: LEFT / RIGHT CAMERAS Forward / Upward / Left / Right facing cameras 17.06oz 9.75in x 3.30in x 1.66in Four 3V Lithium batteries (CR123A type) hours High-density polyethylene (HDPE), anodized aluminum -10ºC to +50ºC, 95% humidity 2.4 to Ghz (4 channel system) 100ft line of sight Wrist Mounted Monitor Pro / Handheld Monitor Pro / Wrist Mounted Monitor / Handheld Monitor / Heads-Up Display / Monocular Micro Viewer 400 TV lines lux Black and White Super-HAD CCD IR LED Flood Illuminator 0.262in thick 6.0in long 1/4 inch stereo jack 68.6 (H) and 47.4 (V) (H) and 32.8 (V) 68.6 (H) and 47.4 (V) RECORDING SPECIFICATIONS: STORAGE MEDIA: RECORDING CAPACITY: SDHC memory card (16GB SDHC card included with system) 16 hours on 16GB SD card (1GB/hour) 2013 Tactical Electronics and Military Supply, L.L.C. All Rights Reserved. Product specifications and information are subject to change without notice. If you encounter any problems with your system, please contact us immediately: Tactical Electronics P.O. Box 152 Broken Arrow, OK (866) TACTICALELECTRONICS.COM PRODUCTS / EOD TRAINING / R & D / AVIATION DESIGN / ENGINEERING / MANUFACTURING HEMLOCK FACILITY 2200 NORTH HEMLOCK AVE / BROKEN ARROW, OK / V: / V: / F: CRUSADER FACILITY 2844 CRUSADER CIRCLE / #100 / VIRGINIA BEACH, VA / V: / F: