jcmtechnologies GSM-CARD/VGSM-CARD user s manual communications card

Transcription

1 jcmtechnologies user s manual GSM-CARD/VGSM-CARD communications card EN

2 Contents Safety instructions 3 Introduction 4 General description 4 Introduction 6 Assembly 6 Configuration 7 Verification 8 LED indicators 8 Solving problems 10 FAQs 10 Technical data 11 Electrical parameters 11 Physical parameters 11 Radiofrequency parameters 11 Using the system 12 EC declaration of conformity jcmtechnologies

3 Safety instructions GSM-CARD / VGSM-CARD In compliance with the European Directive low-voltage electrical equipment, we hereby inform users of the following requirements: Disconnect the device from the power supply before handling. For units which are permanently connected, an easily accessible circuit-breaker device must be built into the wiring system. This system should only be installed by qualified personnel with suitable experience of automatic garage doors and knowledge of applicable European regulations. The instruction manual for this unit must always remain in the possession of the user. jcmtechnologies - 3

4 Introduction General description GSM communication card for real-time management GSM COVERAGE LED INDICATORS GOOD POOR BAD OK ALARM ERROR COVERAGE STAT TX LED GS, TRANSMISSION INDICATORS SMA CONNECTOR FOR GSM ANTENNA LED STATUS INDICATORS CONNECTOR TO MAIN BOARD Connected to an ACCESS-5K access control, it allows remote management of users. Connected to a VERSUS control panel, it allows remote configuration of parameters and alarms. 4 - jcmtechnologies

5 ALARM ERROR BAD OK GOOD POOR COVERAGE STAT TX GSM-CARD / VGSM-CARD Introduction General description Back view MICRO-SD MEMORY CARD SLOT (only Versus) SIM CARD SLOT jcmtechnologies - 5

6 Installation Assembly GOOD POOR BAD OK ALARM ERROR COVERAGE STAT TX GSM ANTENNA Screw the GSM ANTENNA supplied into the SMA connector CONNECTION TO MAIN PCB With the power supply disconnected, insert the card into the device COMMS. CARD ACCESS-5K installation EXPANSION CARD VERSUS installation 6 - jcmtechnologies

7 Configuration GSM-CARD VGSM-CARD To change the default options, you must install the SoftAssistant program for Windows To configure the device, please access the following website: For more information, visit: jcmtechnologies - 7

8 Verification LED indicators LEDs GSM GOOD POOR BAD Good coverage. Optimum data transfer Weak coverage, but sufficient for data transfer Unstable coverage or no connection. We recommend you not use the device in this status, as there may be errors GOOD POOR BAD OK COVERAGE When led indicator is bad, it is recommended to use a 3 meters long GSM antenna extension cable COMMUNICATION LEDS TX Lit during data transmission TX 8 - jcmtechnologies

9 Verification LED indicators Operation LEDs OK System working correctly (flashing=in process) ALARM Use of backup GSM frequency (850 MHz) ERROR System error BAD OK ALARM ERROR GSM-CARD / VGSM-CARD COVERAGE If the GSM-CARD uses the backup frequency, it can interfere with the Motion transmitters ERROR LED Number of flashes Error type Action required 1 Module initialisation Wait for the initialization to be completed 2 SIM card not detected Check SIM card insertion 3 Incorrect PIN Modify communication settings in SoftAssistant 4 SIM card locked Unlock SIM card (for example, with a free mobile) 5 No communication Review GSM antenna connection (see GSM leds) 6 Adjustments not valid Check Unique Key and APN in SoftAssistant 7 Server not detected Contact M2M service provider jcmtechnologies - 9

10 Solving problems FAQs Q: Can I use the supplied SIM to surf in Internet with a smartphone? A: No, the SIM card is type M2M (Machine to Machine), therefore it only connects the main equipment to a private server. Q: Can I use any SIM card, for example the one I have on my phone? A: No you cannot. It only works with bidirectional M2M SIMs from approved operators and specifically configurated. Q: With the serial number that appears on the label, can you access your computer through any SoftAssistant? A: No, you cannot. In addition to the serial number, it is also required the unique key to connect remotely. Q: If I have the main equipment installed, will it work remotely only by plugging in a GSM-CARD? A: Yes, the card is configured by default with the communication parameters of the approved operator jcmtechnologies

11 Technical details GSM-CARD / VGSM-CARD Electrical parameters Power supply Standby / Op. consumption Maximum power absorbed Operating temperature Size (without antenna) 12V dc <500 ma 6W -20ºC +55ºC 77 x 52 x 10 mm Physical parameters Operating temperature Size (without antenna) -20ºC +55ºC 77 x 52 x 10 mm Radiofrequency parameters Radiated power EGSM 850 / 900 / 1800 / 1900 MHz 11 - jcmtechnologies

12 Using the system This device is designed for the use with automatic garage doors. It is not guaranteed for directly activating equipment other than that specified. The manufacturer reserves the right to modify equipment specifications without prior notice. EC declaration of conformity JCM TECHNOLOGIES, S.A. declares that the GSM-CARD/VGSM-CARD complies with the applicable provisions of the section 3 of the R&TTE 2014/35/ CEE Directive and complies the fundamental requirements of the 2014/30/ EU Directive on electromagnetic compatibility and 2006/95/EC on low voltage, insofar as the product is used correctly. Visit UM_ _GSM-CARD_VGSM-CARD_EN_Rev jcmtechnologies