Link GSM idp Manual v1.0

Transcription

1 Link GSM idp Manual v1.0 Please find the latest version of the manual and firmware at

2 Table of Contents 1. Basic features: Function: Installation Assembly of front panel Surface mounting Flush mounting Schema and Connection Relays connection Antenna and SIM card connection Setting of Link GSM idp SIM card programming Setting by SMS Setting by PC through USB via Link GSM idp Manager (optional) Monitor mode Programming mode Table of SMS commands Command types: Names function saved in phone book : Example of SMS exchange : SMS example for Link GSM idp parameters setting: Backup battery Link GSM idp tones LED signaling Electrical parameters... 23

3 1. Basic features: The Link GSM idp is useful for different installation. You just insert a SIM card and connect the power supply, eventually connect the lock. The Link GSM idp use the GSM network, so you do not need any phone line or other cables. On the button, you can configure up to 7 phone numbers that will be progressively dialed after button press. Automatic regulation of microphone volume. 2 independent relays, remotely controlled switching relays with different ways: Activation by ringing, code during call, button press, etc... Recording of numbers from which you activated the relay by ringing. 1 input to connection for example an alarm (alerting by SMS) or for controls the gate opening (beeps during call). Voice messages signaling of different events ( wait please, Open, etc ) 1.1 Function: Hands free GSM phone with preprogrammed phone numbers for 1 with name cards: 1. Outgoing call : After the button is pressed, the Link GSM idp dials the first number saved on the list of numbers. The numbers are saved on the names ABUTTON1 to ABUTTON7. When the called party is busy or not available, the Link GSM idp calls automatically the second number ABUTTON2 etc When the called party picks up the call, the connection is established and the next numbers are not dialed. 2. Incoming call : According to the setting, the Link GSM idp can accepts all the calls or only the calls whose the numbers are recorded on the SIM card. The Link GSM idp can also reject the incoming calls. Before picks up the call, the Link GSM idp can alert by preprogrammed melody. 2 remotely controlled switching relay. Each relay can be controlled up settings by different ways: 1. By ringing The authorized number must be registered on the SIM card. If authorized number calls the Link GSM idp, the call is rejects and the relay is activated. The list of numbers used this activation with the time is sent to the preprogrammed number. 2. By code During voice communication (incoming or outgoing call), the called party press 2 digit code by DTMF for relay activation. For each relay you can set different code. 3. By SMS you can remotely switch ON/OFF the selected relay or activate relay for programmed time by SMS. The authorized number must be registered on the SIM card. 4. Camera mode The selected relay is ON when the Link GSM idp picking up the call and it is OFF by hang up up the call. 5. Lighting mode The selected relay is ON by picking up the call and it stays ON for preprogrammed time after hang up. 6. Button mode The selected relay is ON after button press and stays ON for preprogrammed time. 1 adjustable input: 1. SMS sending ALARM ON to preprogrammed number when input is short circuit against ground. SMS ALARM OFF to next preprogrammed number when input is disconnected. 2. Opening detection. When input is activated during call (for example by door opening), the Link GSM idp generates into a call 3 short beeps for time of input activation. Voice signaling of different status. The different status is signaled by voice message. (Language adjustable). When the voice is presented during a call, it is hearable on DoorPhone and called part. p.3 23

4 2. Installation 2.1. Assembly of front panel Using the tool provided, unscrew the screw, as shown below and remove the cover: Dismounting of nameplate : Remove the 4 screws of the transparent protection. Make the appropriate changes on the nameplate and mount the protection using 4 screws Surface mounting Dimension : Height: 182mm Width: 104mm Depth:: 22mm p.4 23

5 Using 3 screws and plugs, fix the doorphone to the wall: 2.3. Flush mounting The dimensions of the flush part are: Height: 182mm Width: 104mm Depth: 22mm Using 3 screws and plugs, fix the doorphone to the wall: p.5 23

6 2.4. Schema and Connection Backup battery GSM module switch SIM card reader Reboot button Programming modul connector 12V power supply Speaker connector Relais 1 Relais 2 Input Volume setting Buttons 1 and 2 connectors Connecteur Micro handicapped norm LED backlight label LED Handicapped norm LED : indicate the status of doorphone : Green LED : Ringing. Blue LED : In call Red LED : door opening p.6 23

7 2.5. Relays connection 1. Basic connection 2 electrical locks and possibility control 2 doors. 2. 2x PSU possibility to use 2x independent power supply. One for Link GSM idp and second for electrical locks. The electrical lock 2 is connected inversely (fire emergency doors). 3. External camera or lighting activation. 4. Electrical lock and additional bell combination Antenna and SIM card connection Place the antenna cable through the cable passage of the doorphone, and screw it on the female antenna connector : p.7 23

8 We recommend use SIM without PIN. Release the SIM holder (1) 1 Move it up (2) Insert the SIM in correct position (3) to the holder. Close the SIM holder (4) Pull the SIM holder for lock up (5) 5 Note: All programmed parameters are saved on the SIM card. The SIM you can insert into Link GSM idp already preprogrammed or setup Link GSM idp after switching ON (bellow). When you want use calls rejection (ringing), ask your GSM provider to switch OFF voice mail at used SIM card. p.8 23

9 3. Setting of Link GSM idp There is 3 ways to configure the Link GSM idp : By SIM card programming By SMS By Link GSM idp manager software (USB) 3.1. SIM card programming 1. Put the SIM card SIM on a mobile phone. 2. When PIN is setup, cancel it 3. Save the remotely administrator number under name ADMIN1 on the phonebook of SIM card. 4. Save the number that should be dialed after pressing button1 under name ABOUTTON1 5. If you want dial automatically next numbers (when first number is busy or not available) then save those numbers under appropriate names ABUTTON2 to ABUTTON7. 6. Similarly you can program setting of all parameters (programming table at the end of manual) The way of phone numbers saving on the SIM depends on mobile phone type. Please double check that you save numbers to SIM card and not to internal mobile phone memory! When all necessary cables are connected (relay, locks, Antenna etc.), then connect speaker connector and connect the power supply. The red LED lights on and after a while yellow LED start flashing. The Link GSM idp informed by tones or by voice SIM reading, GSM network registration and ready for operation. Now you can put on front panel of Link GSM idp but don t screw it. When SIM is preprogrammed you can try first connections: push the button. The GDI must dial the programmed phone number. When SIM is not preprogrammed then first step is SIM programming and then try connection. After voice connection you can adjust setting of speaker volume. Then screw up front panel of Link GSM idp Setting by SMS Due security reasons you can program the Link GSM idp parameters from authorized numbers only. The authorized numbers are saved on SIM card under names «ADMIN1» to «ADMIN9». The SMS are always written by BIG LETTERS Each SMS elements are spited by space. First word is always command, the further word is one or more parameters. Example: INIT ADMIN Please find all commands in table at the end of manual. p For the first use, when the SIM card doesn t contents any ADMINx name, it is necessary to add the number to the SIM card by SMS with the command INIT. The SMS can be sent from any number. If the SIM card already contents even one number under name ADMINx, the command is ignored. 2. If you need to control the Link GSM idp with a next ADMIN numbers: from mobile phone with ADMINx number, send the SMS to the Link GSM idp with numbers of next ADMINx in SMS format: WRITE ADMIN2 +33xxxxxxxxx (WRITE ADMIN3 etc.). 3. From mobile phone with numbers ADMINx send the SMS to the Link GSM idp with numbers, which should be dial after button press. SMS format: WRITE ABUTTON1 +33xxxxxxxxx 4. Up your needs send next SMS with other parameters for opening by ringing, SMS alarm sending, etc.. 5. You can setup individually for each parameter with appropriate SMS. When you need setup more parameters simultaneously, we recommend use SMS for batch setting. By SMS READ PAR to read firstly current setting to your mobile.

10 By editor of SMS messages change at received SMS word READ to WRITE as same as adjust parameters up your needs. Such adjusted SMS send back to Link GSM idp as reply. The parameters will be setup Setting by PC through USB via Link GSM idp Manager (optional) Remove front cover of the Link GSM idp and connect the MiniUSB cable to PC and programming module. The red LED must light on at the module. During first usage, the USB driver might be installed. USB driver is available on 1. Run Link Link GSM idp Manager program and setup the appropriate port. 2. You can program the Link GSM idp after that display GSM signal strength and voltage (back up ACU). Now you can program: Monitor mode Before programming the paramters, you must stop the Link GSM idp. For monitoring operation don t press Stop, the Link GSM idp must be running! Identification of serial line connection After Link GSM idp voice connection, will show voltage. After Link GSM idp voice connection, will show GSM signal strength p.10 23

11 After click to button monitor is shown Link GSM idp operation (when operation is not stopped by button STOP) Record savings from monitor to file (for service purposes record sending) Programming mode After press the Stop button, The program sends the command to Link GSM idp and wait for the DoorPhone response. Waiting for Link GSM idp response Item Buttons It is designed for programming phone numbers under each buttons Item for 1 button Field to program up to 7 phone numbers p.11 23

12 Item for 1 button Item for 2 buttons Saving of all parameters to Link GSM idp Reading of all parameters from Link GSM idp Saving of all parameters to file on PC GSM provider Loading of all parameters from file on PC Field to up to 7 phone numbers for second button SIM number of position software and firwmare version Item Phone Book Phone book of authorized numbers for ringing opening or automatic call receiving. contact name contact phone number Insert new line Delete line Find name p Item Setting

13 Item Calls Loudness of speaker setting Loudness of microphone setting Incoming call setting : - reject (opening by ringing) - automatically picked up calls from numbers at list only - pick up all calls Signalization - Informing by tones - Ringing during incoming call - Voice signalling Item Relays Item relay Relay 1 parameters Relay 2 parameters Relay mode: - camera - light - button - control by SMS Relay control by ringing only from SIM phone numbers or from all phone numbers. DTMF code for relay activation during a call Relay time of activation p.13 23

14 Item SMS Number where will be sent SMS ALARM ON when input is activated Number where will be sent SMS ALARM OFF when input is deactivated Input mode: - Input disable - Tones when input is activated during a call (open signal) - sending SMS Sending SMS to ADMIN1 with list of numbers which activated relay by ringing. Activation of time settings from GSM network Item ADMIN numbers setting Field to save up to 7 ADMIN numbers Item Service This Item is designed to upgrade the firmware version or change the voice message on the Link GSM idp. CAUTION: Unauthorized manipulation can blocked the unit p.14 23

15 Loading of list from PC List erasing Start of files saving on Link GSM idp. The Indicator shows the process of savings. Savings of selected ringing Select and play ringing tone When all parameters are setup, click to the save button to save the setting on Link GSM idp. Return from programming mode to monitor mode (restart of Link GSM idp) : To return to monitor mode, click on Run button. Program detects the Link GSM idp runs the same way like stop: When you click on Run button, the behavior of Link GSM idp is the same like during power supply connection (tones, eventually voice messages). p.15 23

16 4. Table of SMS commands SMS command Descriptions Default READ STAT Reading the status (firmware, time, relays status etc.) This commands can be sent only from ADMINx numbers This commands can be sent only from ADMINx numbers READ PAR READ JMENO CLR JMENO INIT ADMIN1 +420cc...c Reading of all setup parameters Reading of phone number for NAME Erasing phone number for NAME Initialization first Link GSM idp setting to configure the ADMIN1 number SET REL1 ON Activation relay 1 SET REL1 OFF Deactivation relay 1 SET REL1 ON xx Activation relay1 for xx minutes (xx=00-99) SET REL2 ON Activation relay 2 SET REL2 OFF Deactivation relay 2 SET REL2 ON xx Activation relay 2 for xx minutes (xx=00-99) WRITE JMENO Saving of phone number under NAME +420cc...c WRITE PAR VOLIN:x Saving of microphone loudness [x=1-7] 4 WRITE PAR VOLOUT:x Saving of speaker loudness [x=1-7] 4 WRITE PAR INCALL:x WRITE PAR TMGSM:x WRITE PAR TONE:x Processing of incoming call: X=0 : calls rejected (ringing in) x=1 : calls received from SIM only (list) x=2 : all calls received Time setup up GSM network X=0 : OFF X=1 : ON Setting of acoustic signalization: X=0 : switch OFF X=1 : signaling by service tones X=2 : ringing of incoming call is ON X=4 : signaling by voice messages and combination for ex. 7 all is ON WRITE PAR INPMOD:x Input mode : x=0 : deactivated x=1 : beeps into call (opening indication) x=2 : send SMS during activation/deactivation WRITE PAR RL1COD:yy WRITE PAR RL1MOD:x Code for relay1 activation during call yy= 0-9 Relay 1 modes x=0 : control by SMS x=1 : switch mode (ringing in only from SIM phone number or by code) x=2 : camera mode (activated by pick up, deactivated by hang up) x=3 : lighting mode (activated by pick up and stays ON for activation time after hang up x=4 : activated for activation time after button press x=5 : switch mode all (ringing in from all phone number or by code) p.16 23

17 WRITE PAR RL1TMON:yy WRITE PAR RL1RING:x WRITE PAR RL2COD:y WRITE PAR RL2MOD:x WRITE PAR RL2TMON:yy WRITE PAR RL2RING:x WRITE ALARMON +420cc..c WRITE ALARMOFF +420cc..c CAL AT+CSQ CAL AT+CPBR=x CAL AT+C CLK= <time> Relay1 activation time after ringing in or by code yy seconds yy=00-99 Relay1 activation by ringing in x=0 : OFF x=1 : ON Code for relay2 activation during call y= 0-9 Relay 2 modes x=0 : control by SMS x=1 : switch mode (ringing in only from SIM phone number or by code) x=2 : camera mode (activated by pick up, deactivated by hang up) x=3 : lighting mode (activated by pick up and stays ON for activation time after hang up x=4 : activated for activation time after button press x=5 : switch mode all (ringing in from all phone number or by code) Relay2 activation time after ringing in or by code yy seconds yy=00-99 Relay2 activation by ringing in x=0 : OFF x=1 : ON Savings of number for SMS «ALARM ON» (input grounding) Savings of number for SMS «ALARM OFF» (input disconnection) Signal strength level Info about number saved on position x Setup time in GDI <time> Format <time>= yy/mm/dd,hh:mm:ss±zz yy year (00-99) MM month (01-12) dd day (01-31) hh hours (00-23) mm minutes (00 59) ss seconds (00 59) ±zz time zone ( ) hours Command types: READ command to read the parameters. CLR command to erase phone numbers from SIM card. CAUTION! When you use SMS for numbers erasing then don t forget that one ADMINx number must stayed! Otherwise remote settings will not be possible (necessary to make new initialization). p.17 23

18 INIT Initialization. During the first setting when SIM doesn t includes any ADMINx number, it is necessary to put such number on the SIM card. It is done by SMS with INIT command. The SMS can be sent from any number. When SIM card already has at least one number with name ADMINx the command is ignored. WRITE command to save the parameters. CAL after command CAL, you can put any «AT command» used by the GSM module (for example: module reset, time setting etc.). Those commands please use with appropriate knowledge only! It can cause blocking of whole unit! 4.2. Names function saved in phone book : Name ABUTTON1 ABUTTON2 ABUTTON3 ABUTTON4 ABUTTON5 ABUTTON6 ABUTTON7 BBUTTON1 BBUTTON2 Description - It s the called number when you push the button. ABUTTON1 is busy, unreachable, or not picked up. ABUTTON2 is busy, unreachable, or not picked up. - Relay1 or relay2 are activated by ringing in ABUTTON3 is busy, unreachable, or not picked up. - Relay1 or relay2 activated by ringing in ABUTTON4 is busy, unreachable, or not picked up. ABUTTON5 is busy, unreachable, or not picked up. ABUTTON6 is busy, unreachable, or not picked up. - It s the called number when you push the button. (for Link GSM idp with 2 buttons) BBUTTON1 is busy, unreachable, or not picked up. p.18 23

19 BBUTTON3 BBUTTON4 BBUTTON5 BBUTTON6 BBUTTON7 ADMIN2 to ADMIN7 ADMIN1 Various name ALARMON ALARMOFF BBUTTON2 is busy, unreachable, or not picked up. BBUTTON3 is busy, unreachable, or not picked up. BBUTTON4 is busy, unreachable, or not picked up. BBUTTON5 is busy, unreachable, or not picked up. BBUTTON6 is busy, unreachable, or not picked up. - Relay1 or relay2 are activated by ringing in. - Relay1 or relay2 are by SMS - Read the Link GSM idp status and numbers in phone book by SMS - Edit name and numbers on SIM card by SMS - Control next features by SMS (AT commands) - Setup parameters by SMS The same like ADMIN2 to ADMIN7 and more over: - This number can receive the reports by SMS, includes list of relay activation by ringing in - This number can receive the SMS about low battery level (option). - Relay1 or relay2 are activated by ringing in. - calls are automatically received from this number - This number receives the ALARM ON SMS when input is activated against ground - This number receives the ALARM OFF SMS when input is activated against ground p VER - firmware version in GDI - just info do not adjust! PARGDI - Link GSM idp parameters A# B# C (default is 4#4#0#0#1#5#0#0) A : microphone sensitivity [1-7] B : speaker loudness [1-7] C : incoming calls: 0 : all rejected (ringing in relays activation) 1 : accept from numbers on SIM card only 2 : accept all D : record who opened by ringing in : 0 : deactivated 1 : activated

20 E time setup from GSM network: 0 : deactivated 1 : activated F : signalization: 0 : OFF 1 : tones 2 : ringing of incoming call 4 : voice messages All combination available for ex. All is ON = 7 G : input mode: 0 : input deactivated 1 : when input is grounded, beeps into call (Signaling of opened door) 2 : SMS when input is activated/deactivated PARRL1 - Parameters for relay 1 A# B# CC# D 5#1#03#1) A : DTMF code to activate the relay during call [0-9] B : relay mode: 0 : SMS mode, control by SMS 1 : switch mode, activated by ringing in from SIM phone numbers or by DTMF code during call 2 : camera mode (activated by pick up, deactivated by hang up) 3 : lighting mode (activated by pick up, stays activated for activation time after hang up. 4 : button mode (activated for activation time after button press 5 : switch mode all, activated by ringing in all phone numbers or by DTMF code during call. CC : activation time [00-99] D : relay activation by ringing in: 0 : deactivated 1 : activated PARRL2 - parameters for relay 2 A# B# CC# D 6#0#05#0) A : DTMF code to activate the relay during call [0-9] B : relay mode: 0 : SMS mode, control by SMS 1 : switch mode, activated by ringing in from SIM phone numbers or by DTMF code during call 2 : camera mode (activated by pick up, deactivated by hang up) 3 : lighting mode (activated by pick up, stays activated for activation time after hang up. 4 : button mode (activated for activation time after button press 5 : switch mode all, activated by ringing in all phone numbers or by DTMF code during call. CC : activation time [00-99] D : relay activation by ringing in: 0 : deactivated 1 : activated p Names with numbers can be saved to phone book also by a mobile phone. (Follow instruction of mobile phone manual). Names ABUTONx, BBUTONx, ADMINx, ALARMON, ALARMOFF, PARGDI, PARRL1, PARRL2 must be written by big letters. Between names and numbers is not a space.

21 4.3. Example of SMS exchange : Link GSM idp response for SMS «READ STAT» : READ STATUS: VER: 101 BATTERY:4030mV TIME: "00/01/01,00:01:55" OPER: T-Mobile CZ INP:1 RL1:0 RL1:0 Link GSM idp for SMS «READ PAR» : READ PAR: VOLIN:4 VOLOUT:4 INCALL:0 WRCALL:1 TMGSM:1 TONE:5 INPMOD:2 RL1COD:5 RL1MOD:4 RL1TMON:03 RL1RING:1 RL2COD:66 RL2MOD:1 RL2TMON:05 RL2RING: SMS example for Link GSM idp parameters setting: WRITE PAR: VOLIN:1 TONE:7 INPMOD:2 RL1COD:12 5. Backup battery Use only the Li-Ion batteries mAh. Before inserting or removing the battery, move the switch to OFF. To insert the battery, start by the «+». To remove, start with the «-». p.21 23

22 6. Link GSM idp tones High tone Alerting Detects not registration to GSM net (antenna not connected, wrong PIN), dialling number to GSM etc.. Medium level tone verify action Reads the SIM, registrate to network, answer for SMS, measure voltage etc... Low level tone error Detects error (for example: low voltage, no GSM reaction for command. Can react by unit restart High tone follow by medium level tones in period cca 5 sec. start doorphone a initialization of (registration to network, SIM reading, etc..) High tone repeated Detects disconnection from GSM net (antena disconnect ed, wrong PIN...) Medium level tone repeated during button holding, high tone Button press detection, dial of preprogrammed number High tone, once after dial number to GSM Called party reached 7. LED signaling Permanent light Power supply is ON Not light GDI switched OFF Not light GDI switched OFF Flashing space and light same duration Not registered to GSM network Short flashing with frequency 2 sec. Registered to GSM network Permanent light Establish a call or it is a call p.22 23

23 8. Electrical parameters Operating condition temperature: -20 to + 50 C Humidity: 10% 80% at 30 C Power supply 12 (9-24) V AC/DC, 200mA (optionally integrated ACU 2000mAh for cca 48h of operation) Buttons 1 (or optional 2) Relay 2x Max. voltage Max. Current Activation time by code Activation time by SMS switching contact 48V when I<1A 2A when U<30V 1 to 99 sec 1 to 99 min Input: 0/5V GSM: networks 850/900/1800/1900 MHz SIM 3V, 1.8V p.23 23