Telephony and LAN Planning

Size: px
Start display at page:

Download "Telephony and LAN Planning"

Transcription

1 CHAPTER 3 Use the information in this chapter to prepare for the installation of the Cisco Unified MeetingPlace system telephony and LAN components. This chapter contains the following sections: Cisco Unified MeetingPlace Components, page 3-1 Selecting a Site, page 3-1 Worksheets, page 3-2 Cisco Unified MeetingPlace Components The Cisco Unified MeetingPlace system includes the following hardware and software components: The Audio Server hardware is a call- and voice-processing hardware platform that connects to the phone network and to a compatible LAN. The Audio Server software controls the platform and provides Cisco Unified MeetingPlace functions to desktops on the LAN. It also provides digital telephony access to PSTN callers and IP telephony access to Voice over IP (VoIP) callers. The Audio Server software communicates with other Cisco Unified MeetingPlace components over the LAN or WAN. (For details, see the About Cisco Unified MeetingPlace Integration Applications section on page 1-21.) Selecting a Site The Cisco Unified MeetingPlace 8100 series hardware is usually installed in an equipment room (for example, a PBX or computer room). The location must meet the Cisco Unified MeetingPlace system environmental and power requirements and must allow you to connect the system to the phone network and LAN. For environmental requirements and hardware specifications for the Cisco Unified MeetingPlace 8100 series server, refer to the Preparing to Install the Cisco Unified MeetingPlace 8100 Series Server chapter of the Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server This section contains the following information: LAN Workstation Minimum Configuration, page 3-2 Sensitivity to Network Traffic, page

2 Worksheets Chapter 3 Caution This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. LAN Workstation Minimum Configuration You must install additional MeetingTime software on Microsoft Windows software-based desktops for use by Cisco Unified MeetingPlace end users, contacts, and attendants. Sensitivity to Network Traffic Because Cisco Unified MeetingPlace is connected to the LAN network, traffic on the local LAN segment can affect Cisco Unified MeetingPlace operations. In particular, a broadcast storm (one or more systems on a network segment continuously sends message packets to the local broadcast address) can bring a Cisco Unified MeetingPlace system down for the duration of the storm. Unless the system administrator is certain that broadcast storms will not occur, the Cisco Unified MeetingPlace 8106 or 8112 server should be partially isolated from the rest of the network. To isolate the server, you can use an Ethernet router or switch. An Ethernet switch is usually simpler and less expensive than a router. Many switches include filtering mechanisms that control broadcasts. (For example, the 3COM LinkSwitch 1000 temporarily shuts down any port that generates an abnormal number of broadcast messages.) A Cisco Unified MeetingPlace system connected directly to a filtering switch is virtually immune to broadcast storms. A Cisco Unified MeetingPlace server placed on its own router segment is also immune to broadcast storms. A moderately expensive solution is to place a two-ethernet-port router between the Cisco Unified MeetingPlace system and the main network. An example of such a device is the Cisco Caution A router-based solution implies creating a new LAN segment with its own IP address range. Worksheets Use the worksheets below to gather information for the telephony- and LAN-planning portion of your Cisco Unified MeetingPlace system installation. Each worksheet includes a list of requirements that you must provide to ensure a successful installation. Worksheet 3-1: Cisco Unified MeetingPlace Telephony Requirements for Non-ISDN T1 Lines (U.S., Canada, Japan), page 3-4 Worksheet 3-2: Cisco Unified MeetingPlace Telephony Requirements for ISDN-PRI Lines (U.S., Canada, Japan), page 3-6 Worksheet 3-3: Cisco Unified MeetingPlace Telephony Requirements (Hong Kong), page 3-8 Worksheet 3-4: Cisco Unified MeetingPlace Telephony Requirements (Europe), page

3 Chapter 3 Worksheets Worksheet 3-5: Cisco Unified MeetingPlace LAN Requirements (Worldwide), page 3-12 Worksheet 3-6: Cisco Unified MeetingPlace VoIP Phone Connections Requirements (Worldwide), page 3-14

4 Chapter 3 Worksheet 3-1: Cisco Unified MeetingPlace Telephony Requirements for Non-ISDN T1 Lines (U.S., Canada, Japan) Worksheet 3-1: Cisco Unified MeetingPlace Telephony Requirements for Non-ISDN T1 Lines (U.S., Canada, Japan) This worksheet describes the telephony requirements for non-isdn T1 lines for the United States, Canada, and Japan. 1. Access ports Number of access ports (user licenses) your company purchased: # 2. Telephony setup How Cisco Unified MeetingPlace will attach to the phone network: Directly to PSTN (U.S. and Canada only) Through a PBX 3. T1 lines Order T1 lines to accommodate the number of T1 ports purchased. 4. Trunking type The trunking type provided to the Cisco Unified MeetingPlace system: Digital trunks 5. PBX requirements Order additional hardware or software for your PBX to accommodate new T1 lines. The following telephony components or services can take from 4 to 6 weeks to order and install: 6. Cisco Unified MeetingPlace phone number(s) Network Telco Service (trunk lines, main phone number, or combined access numbers) PBX specific hardware or software (Smart Blades, software upgrade) Additional hardware (CSU, UPS) 7. Digital line requirements Standard or fractional T1 The main phone number (800 and/or local) at the beginning of the range. Channelized into 24 channels Ability to receive calls Ability to place calls (required for outdials and alarm outcalls) Ability to hunt all ports (linear, circular, UCD, or ACD) Toll restriction on ports lifted (required for outdials and alarm outcalls) DTMF generated by all PBX or network phones, including the operator console Male RJ-48C jack connector (U.S. and Canada only) Note PBX/Telco must provide disconnect supervision. If using DID Meeting Access, the numbering plan for DID/DNIS or DDI, including ranges for Combined, Profile, and Direct Meeting Access. 3-4

5 Chapter 3 Worksheet 3-1: Cisco Unified MeetingPlace Telephony Requirements for Non-ISDN T1 Lines (U.S., Canada, Japan) Signaling E&M wink Start (default configuration) Note MeetingTime supports only line-side loop-start and Ground Start CAS protocols but supports both line-side and trunk-side Wink Start CAS protocols. Ground Start from local Telco service E&M Wink Start, DTMF digits, and DID/DNIS or DDI Clear Channel Loop start (OPS) Coding format B8ZS (strongly recommended) or one of the following: Jammed Bit (bit stuffing) AMI Note If AMI is used, the number of zeros (0) in a row may exceed the recommended Telco value of 15. This can happen if all participants in the same meeting are on the same span. In that case, a 0s pattern could be sent to all channels at the same time, exceeding the maximum. This, in turn, can lead to meeting participants being dropped by the Telco from the meeting. Therefore, use B8ZS or Jammed Bit, if possible. Framing One of the following: Extended super frame (ESF) (strongly recommended) Standard super frame D4 (SF/D4) Note T1 facilities using D4 framing are susceptible to false triggering of yellow alarm signals. This false triggering can lead to dropped calls. Conferencing applications are particularly susceptible to this problem with D4 framing. The problem can occur when all 24 channels on a single span are in a conference and are carrying identical data streams. D4 transmission equipment in the network can falsely interpret the identical data on all 24 channels as a yellow alarm signal. For this reason, we recommend configuring T1 spans for ESF framing. Additional hardware Channel service unit (CSU) required for each T1 connection over 330 feet (100 meters) from the demarcation point (demarc) or from the PBX. 8. Modem requirements Analog phone line, or PBX connection Pilot number, accessible from outside RJ-11C connector 9. Translation table Translation table requirements for dialing restrictions. 3-5

6 Worksheet 3-2: Cisco Unified MeetingPlace Telephony Requirements for ISDN-PRI Lines (U.S., Canada, Japan) Chapter 3 Worksheet 3-2: Cisco Unified MeetingPlace Telephony Requirements for ISDN-PRI Lines (U.S., Canada, Japan) This worksheet describes the telephony requirements for ISDN-PRI lines for the United States, Canada, and Japan. 1. Access ports Number of access ports (user licenses) your company purchased: # 2. Telephony setup How Cisco Unified MeetingPlace will attach to the phone network: Directly to PSTN (U.S. and Canada only) Through a PBX 3. ISDN-PRI lines Order ISDN-PRI lines to accommodate the number of ISDN-PRI ports purchased. 4. Trunking type The trunking type provided to the Cisco Unified MeetingPlace system: Digital trunks 5. PBX requirements Order additional hardware or software for your PBX to accommodate new T1 lines. The following telephony components or services can take from 4 to 6 weeks to order and install: 6. Cisco Unified MeetingPlace phone number(s) Network Telco Service (trunk lines, main phone number, or combined access numbers) PBX specific hardware or software (Smart Blades, software upgrade) Additional hardware (CSU, UPS) 7. Digital line requirements Standard or fractional T1 The main phone number (800 or local) at the beginning of the range. Channelized into 24 channels (with 23 B-channels and one D-channel in timeslot 24) NFAS (Non-Facility Associated Signaling with one ISDN trunk controlled by the D-channel of another) is not allowed Ability to receive calls Ability to place calls (required for outdials and alarm outcalls) Ability to hunt all ports (linear, circular, UCD, or ACD) Toll restriction on ports lifted (required for outdials and alarm outcalls) DTMF generated by all PBX or network phones, including the operator console Male RJ-48C jack connector (U.S. and Canada only) Note PBX/Telco must provide disconnect supervision. If using DID Meeting Access, numbering plan for DID/DNIS or DDI, including ranges for Combined, Profile, and Direct Meeting Access 3-6

7 Chapter 3 Worksheet 3-2: Cisco Unified MeetingPlace Telephony Requirements for ISDN-PRI Lines (U.S., Canada, Japan) Signaling AT&T TR41459 ISDN (default configuration) Nortel DMS-100 ISDN Telcordia Technologies NI-2 ISDN Coding format B8ZS (strongly recommended), or one of the following: Jammed Bit (bit stuffing) AMI Note If AMI is used, the number of zeros (0) in a row may exceed the recommended Telco value of 15. This can happen if all participants in the same meeting are on the same span. In that case, a 0s pattern can be sent to all channels at the same time, exceeding the maximum. This, in turn, can lead to meeting participants being dropped by the Telco from the meeting. Therefore, use B8ZS or Jammed Bit, if possible. Framing One of the following: Extended super frame (ESF) (strongly recommended) Standard super frame D4 (SF/D4) Note T1 facilities using D4 framing are susceptible to false triggering of yellow alarm signals. This false triggering can lead to dropped calls. Conferencing applications are particularly susceptible to this problem with D4 framing. The problem can occur when all 24 channels on a single span are in a conference and are carrying identical data streams. D4 transmission equipment in the network can falsely interpret the identical data on all 24 channels as a yellow alarm signal. For this reason, Cisco recommends configuring T1 spans for ESF framing. Additional hardware Channel service unit (CSU) required for each T1 connection over 330 feet (100 meters) from the demarcation point (demarc) or from the PBX. 8. Modem requirements Analog phone line, or PBX connection Pilot number, accessible from outside RJ-11C connector 9. Translation table Translation table requirements for dialing restrictions. 3-7

8 Worksheet 3-3: Cisco Unified MeetingPlace Telephony Requirements (Hong Kong) Chapter 3 Worksheet 3-3: Cisco Unified MeetingPlace Telephony Requirements (Hong Kong) This worksheet describes the non-isdn T1 CAS telephony requirements for Hong Kong. Note If you are planning a T1-PRI telephony installation for Hong Kong, use the information in Worksheet 3-2: Cisco Unified MeetingPlace Telephony Requirements for ISDN-PRI Lines (U.S., Canada, Japan), page Access ports Number of access ports (user licenses) your company purchased: # 2. Telephony setup How Cisco Unified MeetingPlace will attach to the phone network: Directly to PSTN Through a PBX 3. T1 lines Order T1 lines to accommodate the number of T1 ports purchased. 4. Trunking type The trunking type provided with the Cisco Unified MeetingPlace system: Digital trunks Mbps T1 IDA M service 5. PBX requirements Order additional hardware or software for your PBX to accommodate new T1 lines. The following telephony components or services can take from 4 to 6 weeks to order and install: 6. Cisco Unified MeetingPlace phone number(s) Network Telco Service (trunk lines, main phone number, or combined access numbers) PBX specific hardware or software (Smart Blades, software upgrade) Additional hardware (CSU, UPS) 7. Digital line requirements Standard or fractional T1 The main phone number (800 and/or local) at the beginning of the range. Channelized into 24 channels Ability to receive calls Ability to place calls (required for outdials and alarm outcalls) Ability to hunt all ports (linear, circular, UCD, or ACD) Toll restriction on ports lifted (required for outdials and alarm outcalls) DTMF generated by all PBX or network phones, including the operator console Male RJ-45 jack connector Note PBX/Telco must provide disconnect supervision. 3-8

9 Chapter 3 Worksheet 3-3: Cisco Unified MeetingPlace Telephony Requirements (Hong Kong) Signaling One of the following: If using DID Meeting Access, numbering plan for DID/DNIS or DDI, including ranges for Combined, Profile, and Direct Meeting Access E&M Wink Start E&M Wink Start, DTMF digits, and DID/DNIS or DDI Loop start only Coding format One of the following: B8ZS (preferred) Jammed Bit (bit stuffing) AMI Note If AMI is used, the number of zeros (0) in a row may exceed the recommended Telco value of 15. This can happen if all participants in the same meeting are on the same span. In that case, a 0s pattern can be sent to all channels at the same time, exceeding the maximum. This, in turn, can lead to meeting participants being dropped by the Telco from the meeting. Therefore, use B8ZS or Jammed Bit, if possible. Framing One of the following: Extended super frame (ESF) (preferred) Standard super frame D4 (SF/D4) Note Triggering of yellow alarm signals. This false triggering can lead to dropped calls. Conferencing applications are particularly susceptible to this problem with D4 framing. The problem can occur when all 24 channels on a single span are in a conference and are carrying identical data streams. D4 transmission equipment in the network can falsely interpret the identical data on all 24 channels as a yellow alarm signal. For this reason, Cisco recommends configuring T1 spans for ESF framing. Additional hardware Channel service unit (CSU) required for each T1 connection over 330 feet (100 meters) from the demarcation point (demarc) or from the PBX. 8. Modem requirements Analog phone line, or PBX connection Pilot number, accessible from outside RJ-11C connector 9. Translation table Translation table requirements for dialing restrictions. 3-9

10 Worksheet 3-4: Cisco Unified MeetingPlace Telephony Requirements (Europe) Chapter 3 Worksheet 3-4: Cisco Unified MeetingPlace Telephony Requirements (Europe) This worksheet describes the telephony requirements for Europe. 1. Access ports Number of access ports (user licenses) your company purchased: # 2. Telephony setup How Cisco Unified MeetingPlace will attach to the phone network: Directly to PSTN Through a PBX 3. E1 lines Order E1 lines to accommodate the number of E1 ports purchased. 4. Trunking type The trunking type provided with the Cisco Unified MeetingPlace system: Digital trunks 5. PBX requirements Order additional hardware or software for your PBX to accommodate new E1 lines. The following telephony components or services can take from 4 to 6 weeks to order and install: 6. Cisco Unified MeetingPlace phone number(s) 7. Digital line requirements Standard E1 Network Telco Service (trunk lines, main phone number, or combined access numbers) PBX specific hardware or software (Smart Blades, software upgrade) Additional hardware (CSU, UPS) The main phone number (800 and/or local) at the beginning of the range. Channelized into 30 channels (30 B channels, plus 1 D-channel and 1 framing channel Ability to receive calls Signaling One of the following: Ability to place calls (required for outdials and alarm outcalls) Ability to hunt all ports (linear, circular, UCD, or ACD) Toll restriction on ports lifted (required for outdials and alarm outcalls) DTMF generated by all PBX or network phones, including the operator console Male RJ-48C jack connector (on the Cisco Unified MeetingPlace side) If using DID Meeting Access, numbering plan for DID/DNIS or DDI, including ranges for Combined, Profile, and Direct Meeting Access Euro-ISDN (default configuration) QSIG: either QSIG_ECMA (channels are numbered 1 30) or QSIG_ETSI (channels are numbered 1 15, 17 31) 3-10

11 Chapter 3 Worksheet 3-4: Cisco Unified MeetingPlace Telephony Requirements (Europe) Coding format One of the following: HDB3 (strongly recommended) AMI Note If AMI is used, the number of zeros (0) in a row may exceed the recommended Telco value of 15. This can happen if all participants in the same meeting are on the same span. In that case, a 0s pattern can be sent to all channels at the same time, exceeding the maximum. This, in turn, can lead to meeting participants being dropped by the Telco from the meeting. Therefore, use B8ZS or Jammed Bit, if possible. Framing One of the following: CRC4 checking (strongly recommended) Non-CRC4 Additional hardware No channel service unit (CSU) required in Europe, because the Telco provides its own. 8. Modem requirements Analog phone line, or PBX connection Pilot number, accessible from outside RJ-11C connector 9. Translation table Translation table requirements for dialing restrictions. 3-11

12 Worksheet 3-5: Cisco Unified MeetingPlace LAN Requirements (Worldwide) Chapter 3 Worksheet 3-5: Cisco Unified MeetingPlace LAN Requirements (Worldwide) This worksheet describes the LAN requirements for the United States, Canada, and Japan. 1. Cable/connector requirements 2. Desktop requirements (MeetingTime) Connections from Cisco Unified MeetingPlace server to your network: For twisted-pair Ethernet, 100BASE-TX. Provide an RJ-45 connector. 10BASE-T works, but is not recommended. This cable is customer supplied. Connection from Cisco Unified MeetingPlace Multi Access Blade to your network: For twisted-pair Ethernet, 100BASE-TX. Provide an RJ-45 connector. This cable is supplied by Cisco. Cisco provides a 7.5-meter CAT-5e cable with Ferrite snap-on bead (# ) on one end. If the cable is changed, the snap-on bead must be moved. Note The Ethernet switch port (or any other network devices) that the Multi Access Blade connects to directly must be set to fixed 100BASE-TX Full Duplex. Otherwise, you may experience decreased voice quality. (Set the Ethernet port that connects to the CPU card to auto speed and auto duplex.) Provide a desktop system connected to your LAN with the following minimum configuration: Any standard desktop system that runs on Microsoft Windows 98, NT 4.0 or later, or MB available disk space 16 MB RAM (24 MB RAM for Windows NT or 256 MB RAM for Windows 2000) Network interface card 3. Hostname Name for Cisco Unified MeetingPlace on your network. 4. IP address Address of the Cisco Unified MeetingPlace host on the network. Note When you request your IP address and hostname, ensure that your LAN Manager adds this to the name server(s). 5. Subnet mask Mask that completes the address for the Cisco Unified MeetingPlace host. 6. Broadcast address Address used to broadcast packets on the local LAN segment. 7. Default gateway Address of the integration that will accept and route information to the other networks. 8. SNMP IP address IP address for which traps will be sent for trap communities. 9. Name server Ensure all workstations running MeetingTime use a name server (DNS/WINS or local hosts table). 10. NTP server IP address We recommend that you time synchronize your Cisco Unified MeetingPlace system with a Network Time Protocol (NTP) server. (For more information, see Worksheet 5-8: System Parameters, page 5-38.) 3-12

13 Chapter 3 Worksheet 3-5: Cisco Unified MeetingPlace LAN Requirements (Worldwide) 11. Broadcast traffic If the rate of broadcast or multicast packet generation on the LAN segment exceeds an average of 40/second, the Ethernet link from Cisco Unified MeetingPlace into the local LAN must be configured for 100 Mbps to avoid congestion of the link. 12. MeetingTime network requirements 13. MeetingTime LAN speed recommendations If broadcast and multicast traffic exceeds 100 packets/second, the Cisco Unified MeetingPlace system should be isolated from the segment using a router. MeetingTime must be able to open a TCP connection on ports 5001 and 5005 to connect to the network and/or conference server. For MeetingTime to access recordings and attachments, the IP address of the conference server must not be translated using a network address translation scheme. To schedule and monitor small (2 10 participants) meetings: Required: 28 kbs Recommended: 40 kbs To monitor medium meetings (11 60 participants): Required: 35 kbs Recommended: 50 kbs To monitor large meetings ( participants): Required: 50 kbs Recommended: 128 kbs 3-13

14 Worksheet 3-6: Cisco Unified MeetingPlace VoIP Phone Connections Requirements (Worldwide) Chapter 3 Worksheet 3-6: Cisco Unified MeetingPlace VoIP Phone Connections Requirements (Worldwide) This worksheet describes the telephony requirements for Voice over IP (VoIP) telephony connections worldwide. 1. Access ports Number of access ports (user licenses) your company purchased. 2. VoIP access ports Number of these access ports that will be VoIP. 3. Cisco Unified MeetingPlace phone numbers for VoIP access 4. IP addresses to be used by the VoIP RTP streams 5. Subnet mask for RTP IP addresses Note The number of VoIP ports cannot exceed the capacity allowed by your hardware. The main phone numbers (800 and local) at the beginning of the range. IP addresses that will be used by IP phones to connect to the Cisco Unified MeetingPlace Multi Access (MA) blades. Note Up to four IP addresses are needed for Multi Access blades used for VoIP. Each MA-16 needs 1 IP address if 240 or fewer ports are configured on it. For more than 240 ports, an MA-16 needs 2 IP addresses. If the second IP address on an MA-16 is unused, can be used. Each MA-4 will always need exactly 1 IP address. The standard masks used to subdivide the network into smaller groups of IP addresses. Each MA blade requires a subnet mask. For most customers, this mask is the same for all MA blades. 6. Default gateway The IP address of a gateway machine (Cisco MCS) on the local network. Packets with non-local addresses are sent here if no other route is known. Each MA blade requires a default gateway. For most customers, this address is the same for all MA blades. 7. Hostname and IP address of the Cisco Unified MeetingPlace 8100 series server 8. Hostname and IP address of the Cisco Unified MeetingPlace H.323/SIP IP Gateway server 9. (Optional) Hostname and IP address of the Cisco Unified MeetingPlace Web Conferencing server You need to know this value to install and configure Cisco Unified MeetingPlace Audio Server. Configuration of a Cisco Unified MeetingPlace 8100 series server for VoIP involves three components: Cisco Unified MeetingPlace Audio Server Cisco Unified MeetingPlace H.323/SIP IP Gateway software Cisco Unified CallManager or other VoIP soft switch Needed only if the Cisco Unified MeetingPlace Web Conferencing server is running on the same server hardware as Cisco Unified MeetingPlace H.323/SIP IP Gateway software. 3-14

15 Chapter 3 Worksheet 3-6: Cisco Unified MeetingPlace VoIP Phone Connections Requirements (Worldwide) 10. Hostname and IP address of the VoIP soft switch 11. Special soft switch requirements 12. Network infrastructure connected to Cisco Unified MeetingPlace MA blades set to 100BASE-T Full Duplex Cisco SIP Proxy server, Avaya Communication Manager, or other soft switch. Any soft switch requirements that will affect the Cisco Unified MeetingPlace VoIP installation. Ethernet connections that carry the RTP streams to and from the MA blades must be 100 Mbps with no negotiation on either end. 13. Codec type Will you use G.711 u-law, G.711 A-law, or G.729? 14. Packets per second If using a G.711 codec, the number of packets per second that will be transferred (10, 20, 30). Default is 20 per second. 15. Silence suppression Will silence packets be suppressed? Yes means the number of VoIP packets leaving Cisco Unified MeetingPlace will be typically 2 or 3 per 5 seconds if silence is detected. No means packet usage is typically 50 to 150 packets per 5 seconds (depending on the codec used), which uses more bandwidth. 16. QoS system to be used The Quality of Service (QoS) system to be used. This must be either the IP Precedence system or the Differentiated Services Code Point (DSCP) system. 17. QoS subfields If using IP Precedence, select an IP Precedence value from the following list: 0 routine 1 priority 2 immediate 3 flash 4 flash override 5 CRITIC/ECP (standard value) 6 internetwork control 7 network control Also, select a Type of Service (ToS) value (0 to 15). We recommend 0 If using DSCP, select the DSCP value (0 to 63). Standard value is Base UDP port Each MA VoIP entity (anything that requires an IP address) requires a Base UDP port. The Cisco Unified MeetingPlace Audio Server system provides a default value during configuration. The default is 5000 for the first RTP entity and increases by 1000 for each entity. Although we recommend that you accept these defaults, you can provide different values for your needs. 3-15

16 Worksheet 3-6: Cisco Unified MeetingPlace VoIP Phone Connections Requirements (Worldwide) Chapter Jitter buffer setting Each MA blade requires jitter buffer settings to handle variances in the rate at which VoIP packets are received. The Cisco Unified MeetingPlace Audio Server system provides a default value during configuration. The default initial jitter delay (range msec) is 100 milliseconds. This is a good compromise between audio conversation delay and loss of data. The default jitter optimization value (range 0 12) of 7 determines how quickly the system changes the jitter buffer delay, based on network changes. Although we recommend that you accept these defaults, you can provide different values for your needs. 20. Translation for incoming numbers 21. Translation for outgoing numbers How you want incoming numbers to be translated using the dial groups feature in the Cisco Unified MeetingPlace H.323/SIP IP Gateway server (if at all). How you want phone numbers to be translated using the Cisco Unified MeetingPlace Audio Server translation table feature for calls out of the Cisco Unified MeetingPlace system. 22. Digit transport Determine the method by which digits will be sent to the Cisco Unified MeetingPlace Audio Server system through VoIP by your network: As part of the voice stream (fully in-band) As part of the RTP stream carrying the voice packets but as separate packets (referred to as RFC2833 digits) Sent direct to the MP VoIP Gateway which will relay them to Cisco Unified MeetingPlace (full out-of-band) 23. RFC2833 digits If using RFC2833 packets for digit transport, the Cisco Unified MeetingPlace Audio Server system needs to know if a packet actually holds an RFC2833 digit. There is no standard packet identifier number to indicate an RFC2833 digit. The range for this payload type is 96 to 127. Cisco uses an internal default of 101; however, contact your network administrator for what your network will use. 3-16

INDEX. access ports, about 5-6 alarms location of panel 1-3. best practices for security 4-1 blades and port information 1-8

INDEX. access ports, about 5-6 alarms location of panel 1-3. best practices for security 4-1 blades and port information 1-8 INDEX A access ports, about 5-6 alarms location of panel 1-3 B best practices for security 4-1 blades and port information 1-8 C CD-ROM drive, about 1-4 Cisco Unified MeetingPlace about 1-1 Cisco Unified

More information

Chapter TIMG BOILERPLATE

Chapter TIMG BOILERPLATE Pete is the writer for this content; Julie W. is the editor. This file contains the following flows: File: boilerplate.fm; Flow: Reqs-Serial, page -2 File: boilerplate.fm; Flow: Reqs-In-Band, page -4 File:

More information

Getting Started. 16-Channel VoIP Gateway Card. Model No. KX-TDA0490

Getting Started. 16-Channel VoIP Gateway Card. Model No. KX-TDA0490 16-Channel VoIP Gateway Card Getting Started Model No. KX-TDA0490 Thank you for purchasing a Panasonic 16-Channel VoIP Gateway Card. Please read this manual carefully before using this product and save

More information

Getting Started with the VG248

Getting Started with the VG248 CHAPTER 2 Before you can configure the telephony features on the VG248 to interact with the analog phones, you must first configure the basic network, SNMP, and password settings. These settings enable

More information

Expandable SIP Phone System. Expandable SIP Phone System

Expandable SIP Phone System. Expandable SIP Phone System Expandable SIP Phone System Key Features Included: + One DVX-1000 SIP IP PBX + One DIV-140 Trunk Gateway + Ten DPH-140S IP Telephones + Unified Management + Save On Long-distance Calling + Create an IP

More information

Spectrum Enterprise SIP Trunking Service NEC Univerge SV8100 IP PBX Configuration Guide

Spectrum Enterprise SIP Trunking Service NEC Univerge SV8100 IP PBX Configuration Guide Spectrum Enterprise SIP Trunking Service NEC Univerge SV8100 IP PBX Configuration Guide About Spectrum Enterprise: Spectrum Enterprise is a division of Charter Communications following a merger with Time

More information

Setting Up a Serial (SMDI, MCI, or MD-110) PIMG Integration with Cisco Unity Connection

Setting Up a Serial (SMDI, MCI, or MD-110) PIMG Integration with Cisco Unity Connection CHAPTER 11 Setting Up a Serial (SMDI, MCI, or MD-110) PIMG Integration with Cisco Unity Connection For detailed instructions for setting up a serial (SMDI, MCI, or MD-110) PIMG integration with Cisco Unity

More information

SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business

SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business NDA-31871 Issue 1.0 NEC Enterprise Communication Technologies, Inc. reserves the right to change the specifications, functions, or

More information

VoIP with Channel Associated Signaling (CAS)

VoIP with Channel Associated Signaling (CAS) VoIP with Channel Associated Signaling (CAS) Document ID: 14078 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions T1 Signaling: CCS and CAS CCS CAS Configure

More information

FREUND SIP SW - V SIP-server setup

FREUND SIP SW - V SIP-server setup FREUND SIP SW - V1.7.13 SIP-server setup Content 1. Product Setup 4 2. Log in and Home 5 3. Menu 9 3.1 Tools 9 3.1.1 Dashboard 9 3.1.2 Extensions 10 3.1.3 Trunks 14 3.1.4 Groups 18 3.1.5 Ring groups 20

More information

Functionality. About Cisco Unified Videoconferencing 3545 Gateway Products. About the Cisco Unified Videoconferencing 3545 PRI Gateway

Functionality. About Cisco Unified Videoconferencing 3545 Gateway Products. About the Cisco Unified Videoconferencing 3545 PRI Gateway CHAPTER 1 This section describes the following topics: About Cisco Unified Videoconferencing 3545 Gateway Products, page 1-1 About Gateway Features, page 1-2 About Cisco Unified Videoconferencing 3545

More information

Setting Up an Avaya Definity ProLogix Digital PIMG Integration with Cisco Unity Connection

Setting Up an Avaya Definity ProLogix Digital PIMG Integration with Cisco Unity Connection CHAPTER 4 Setting Up an Avaya Definity ProLogix Digital PIMG Integration with Cisco Unity Connection For detailed instructions for setting up an Avaya Definity ProLogix digital PIMG integration with Cisco

More information

InterPrise 3200D. An IP Telephony Gateway for Enterprise Network Applications

InterPrise 3200D. An IP Telephony Gateway for Enterprise Network Applications InterPrise 3200D An IP Telephony Gateway for Enterprise Network Applications Table of Contents Overview... 3 Ease of Integration... 3 Quality Voice Communication... 3 Web-based Calling with ClearConnect

More information

INTRODUCTION. BridgeWay. Headquarters

INTRODUCTION. BridgeWay. Headquarters MILITARY PRODUCTS INTRODUCTION Voiceboard Corporation s MediaPro products provide enhanced communications capabilities for military applications. State of the art technology, including redundant networking,

More information

AP500 4-Port FXS VoIP Gateway

AP500 4-Port FXS VoIP Gateway AP500 4-Port FXS VoIP Gateway High Performance VoIP Gateway Solution Product Overview www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview Hardware Specification APOS Technology

More information

Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server

Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server Release 6.x Published May 31, 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

More information

RP-FSO522 2-Line FXO, 2-Line FXS SIP IP Gateway. Feature

RP-FSO522 2-Line FXO, 2-Line FXS SIP IP Gateway. Feature RP-FSO522 2-Line FXO, 2-Line FXS SIP IP Gateway RP-FSO522 is an 2-Line FXO plus 2-Line FXS gateway with SIP protocol IP device which allows to connect 2 Lines of analog PSTN telephone line and connect

More information

Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1

Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Abstract These Application Notes describe the procedures

More information

Introduction. H.323 Basics CHAPTER

Introduction. H.323 Basics CHAPTER CHAPTER 1 Last revised on: October 30, 2009 This chapter provides an overview of the standard and the video infrastructure components used to build an videoconferencing network. It describes the basics

More information

SIP Public Announcement Adapter with PoE

SIP Public Announcement Adapter with PoE SIP Public Announcement Adapter with New Audio Control System PLANET audio control system comes with the existing to provide unidirectional and bidirectional audio for broadcasting. An announcement can

More information

Spectrum Enterprise SIP Trunking Service NEC Univerge SV9100 IP PBX Configuration Guide

Spectrum Enterprise SIP Trunking Service NEC Univerge SV9100 IP PBX Configuration Guide Spectrum Enterprise SIP Trunking Service NEC Univerge SV9100 IP PBX Configuration Guide About Spectrum Enterprise: Spectrum Enterprise is a division of Charter Communications following a merger with Time

More information

Entry Level PoE IP Phone

Entry Level PoE IP Phone Entry Level IP Phone Key Features Highlights Supports SIP 2.0 (RFC3261) IEEE 802.3af Power over Ethernet compliant (VIP- 1000PT only) Supports HD voice (G.722) Voice Activity Detection Auto Provisioning:

More information

Cisco Analog Telephone Adaptor Overview

Cisco Analog Telephone Adaptor Overview CHAPTER 1 This section describes the hardware and software features of the Cisco Analog Telephone Adaptor (Cisco ATA) and includes a brief overview of the Skinny Client Control Protocol (SCCP). The Cisco

More information

Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use.

Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. IP Networking Guide Pure IP-PBX Model No. KX-TDE100 KX-TDE200/KX-TDE600 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual

More information

LevelOne GES GE with 1 Combo SFP Web Smart Switch User Manual

LevelOne GES GE with 1 Combo SFP Web Smart Switch User Manual LevelOne GES-0852 8 GE with 1 Combo SFP Web Smart Switch User Manual Version 1.0-1109 1 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device,

More information

Avaya PBX SIP TRUNKING Setup & User Guide

Avaya PBX SIP TRUNKING Setup & User Guide Avaya PBX SIP TRUNKING Setup & User Guide Nextiva.com (800) 285-7995 2 P a g e Contents Description... 3 Avaya IP PBX Configuration... 3 Licensing and Physical Hardware... 4 System Tab Configuration...

More information

Switchvox IP PBX Pre-Installation Checklist (to be completed by )

Switchvox IP PBX Pre-Installation Checklist (to be completed by ) Switchvox IP PBX Pre-Installation Checklist (to be completed by ) Project Resources Value Initials Date Customer Project Contact Customer IT Manager Customer PBX Administrator (if applicable) Customer

More information

Setting up Alcatel 4400 Digital PIMG Integration

Setting up Alcatel 4400 Digital PIMG Integration up Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection, on page 1 Up an Alcatel 4400 Digital PIMG Integration with

More information

Introduction to VoIP. Cisco Networking Academy Program Cisco Systems, Inc. All rights reserved. Cisco Public. IP Telephony

Introduction to VoIP. Cisco Networking Academy Program Cisco Systems, Inc. All rights reserved. Cisco Public. IP Telephony Introduction to VoIP Cisco Networking Academy Program 1 Requirements of Voice in an IP Internetwork 2 IP Internetwork IP is connectionless. IP provides multiple paths from source to destination. 3 Packet

More information

Setting Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection

Setting Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection up Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection Up an Alcatel 4400 Digital PIMG Integration with Cisco Unity Connection, page 1 Up an Alcatel 4400 Digital PIMG Integration with Cisco

More information

Setting Up a Mitel SX-2000 Digital PIMG Integration with Cisco Unity Connection

Setting Up a Mitel SX-2000 Digital PIMG Integration with Cisco Unity Connection Up a Mitel SX-2000 Digital PIMG Integration with Cisco Unity Connection Up a Mitel SX-2000 Digital PIMG Integration, page 1 Up a Mitel SX-2000 Digital PIMG Integration Task List for Mitel SX-2000 PIMG

More information

Vmux-110. Voice Trunking Gateway FEATURES

Vmux-110. Voice Trunking Gateway FEATURES Vmux-110 FEATURES Integrates voice and data over packet networks Connects one E1/T1 digital or four/eight (FXS/FXO/E&M) analog voice ports over a serial, TDM or 10/100BaseT uplink Second Ethernet port

More information

4 Port IP-PBX + SIP Gateway System

4 Port IP-PBX + SIP Gateway System 4 Port IP-PBX + SIP Gateway System The IPG-40XG is an embedded Voice over IP (VoIP) PBX Server with Session Initiation Protocol (SIP) to provide IP extension phone connections for global virtual office

More information

AP Port Analog VoIP Gateway High Performance VoIP Gateway Solution

AP Port Analog VoIP Gateway High Performance VoIP Gateway Solution AP2390 72-Port Analog VoIP Gateway High Performance VoIP Gateway Solution Optional DC Power Supply (Model : AP2390D) www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview Hardware

More information

BEC ES08 8 ports Green Ethernet Desktop Switch User Manual

BEC ES08 8 ports Green Ethernet Desktop Switch User Manual BEC ES08 8 ports Green Ethernet Desktop Switch User Manual - 1 - The device is a powerful, high-performance Fast Ethernet switch, with all ports capable of 10 or 100Mbps auto-negotiation operation (NWay),

More information

Mitel PBX interface with Conferencing Server Configuration Notes

Mitel PBX interface with Conferencing Server Configuration Notes Mitel PBX interface with Conferencing Server Configuration Notes Note: This document section is maintained by Mitel Networks When referring to any information in this document please also check the Additions

More information

Cisco MeetingPlace Audio Server 5.2 Customer Engineering Guide (for Cisco MeetingPlace 8112)

Cisco MeetingPlace Audio Server 5.2 Customer Engineering Guide (for Cisco MeetingPlace 8112) Cisco MeetingPlace Audio Server 5.2 Customer Engineering Guide (for Cisco MeetingPlace 8112) Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com

More information

AP800 TM PSTN Backup 4-Port FXS VoIP Gateway High Performance VoIP Gateway Solution

AP800 TM PSTN Backup 4-Port FXS VoIP Gateway High Performance VoIP Gateway Solution AP800 TM PSTN Backup 4-Port FXS VoIP Gateway High Performance VoIP Gateway Solution Product Overview www.addpac.com AddPac Technology 2007, Sales and Marketing Contents Product Overview Hardware Specification

More information

SWITCH RC-415/RC-416 USER S Manual

SWITCH RC-415/RC-416 USER S Manual SWITCH RC-415/RC-416 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

More information

Page 2 Skype Connect Requirements Guide

Page 2 Skype Connect Requirements Guide Thinking about implementing Skype Connect? Read this guide first. Skype Connect provides connectivity between your business and the Skype community. By adding Skype Connect to your existing SIP-enabled

More information

VG-422R. User s Guide

VG-422R. User s Guide VG-422R User s Guide Trademarks Contents are subject to revise without prior notice. All trademarks belong to their respective owners. FCC Warning This equipment has been tested and found to comply with

More information

Cisco SPA400 Voic System with 4-Port FXO Gateway Cisco Small Business Voice Systems

Cisco SPA400 Voic System with 4-Port FXO Gateway Cisco Small Business Voice Systems Cisco SPA400 Voicemail System with 4-Port FXO Gateway Cisco Small Business Voice Systems Voicemail System and Multiport PSTN Gateway Solution for the Cisco SPA9000 Highlights Integrated voicemail and PSTN

More information

AP1100FA 4-Port FXS 4-Port FXO VoIP Gateway High Performance VoIP Gateway Solution

AP1100FA 4-Port FXS 4-Port FXO VoIP Gateway High Performance VoIP Gateway Solution AP1100FA 4-Port FXS 4-Port FXO VoIP Gateway High Performance VoIP Gateway Solution Product Overview www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview Hardware Specification

More information

Dialogic Blue Telephony Boards

Dialogic Blue Telephony Boards is an efficient one-span host-based call-processing board for the open source market, which includes features for Interactive Voice Response (IVR) along with call transfer emulation, G.711 support, Automatic

More information

THE KEY BUILDING BLOCKS OF THE SHORETEL CONNECT PLATFORM

THE KEY BUILDING BLOCKS OF THE SHORETEL CONNECT PLATFORM Product Specifications ShoreTel ST Voice es SOLUTION BRIEF THE KEY BUILDING BLOCKS OF THE SHORETEL CONNECT PLATFORM Available as solid-state appliances or virtualized for deployment in your datacenter

More information

AIM-ATM, AIM-VOICE-30, and AIM-ATM-VOICE-30 on the Cisco 2600 Series and Cisco 3660

AIM-ATM, AIM-VOICE-30, and AIM-ATM-VOICE-30 on the Cisco 2600 Series and Cisco 3660 AIM-ATM, AIM-VOICE-30, and AIM-ATM-VOICE-30 on the Cisco 2600 Series and Cisco 3660 Feature History Release 12.2(2)XA 12.2(2)XB Modification The High-Performance ATM Advanced Integration Module (AIM-ATM)

More information

EP502/EP504 IP PBX 1.1 Overview

EP502/EP504 IP PBX 1.1 Overview 1.1 Overview The EP502/EP504 is an embedded Voice over IP (VoIP) Server with Session Initiation Protocol (SIP) to provide IP extension phone connection for global virtual office of small-to-medium business

More information

VoIP Application Note:

VoIP Application Note: VoIP Application Note: Configure NEC UX5000 w/ Nortel SIP Trunking Service P/N 0913228 Date: 8/12/09 Table of Contents: GOAL... 3 PREREQUISITES... 3 SIP TRUNKING INFORMATION PROVIDED BY NORTEL:... 3 NEC

More information

RMX 1500 Quick Installation & Configuration Guide

RMX 1500 Quick Installation & Configuration Guide RMX 1500 Quick Installation & Configuration Guide General Safety Precautions Follow these rules to ensure general safety: Keep the area around the Polycom RMX 1500 unit clean and free of clutter and well

More information

Vmux-2120 Voice Trunking Gateway

Vmux-2120 Voice Trunking Gateway Data Sheet Vmux-2120 Unique TDMoIP multiplexing, with various voice compression algorithms, provides up to 16:1 compression for effective bandwidth utilization Two channelized uplink ports for point-to-multipoint

More information

Cisco MeetingPlace Express. Network Provisioning and Configuration

Cisco MeetingPlace Express. Network Provisioning and Configuration Cisco MeetingPlace Express Networking Provisioning and Configuration Copyright 2006 Cisco Systems Page 1 Table of Contents 1 Introduction... 3 2 Network Provisioning Considerations... 3 2.1 Voice over

More information

Smart IAD. User s Guide

Smart IAD. User s Guide Smart IAD User s Guide I Trademarks Contents are subject to revise without prior notice. All trademarks belong to their respective owners. FCC Warning This equipment has been tested and found to comply

More information

AP-2GR Port 2G GSM Router High Performance 2G GSM Router Solution

AP-2GR Port 2G GSM Router High Performance 2G GSM Router Solution AP-2GR1001 1-Port 2G GSM Router High Performance 2G GSM Router Solution www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview Hardware Specification 2G GSM Module Specification

More information

Music on Hold. Prerequisites for Music on Hold. Restrictions for Music on Hold

Music on Hold. Prerequisites for Music on Hold. Restrictions for Music on Hold Prerequisites for, page 1 Restrictions for, page 1 Information About, page 2 Configure, page 7 Feature Information for, page 27 Prerequisites for For Unified CME Release 11.6 and previous releases, phones

More information

Monitoring Data CHAPTER

Monitoring Data CHAPTER CHAPTER 4 The Monitor tab provides options to view various types of monitored data. There are options for: Viewing the Monitor Overview Charts, page 4-9 Viewing Application Data, page 4-12 Viewing Voice

More information

Bandwidth, Latency, and QoS for Core Components

Bandwidth, Latency, and QoS for Core Components Bandwidth, Latency, and QoS for Core Components, on page 1 Bandwidth, Latency, and QoS for Optional Cisco Components, on page 18 Bandwidth, Latency, and QoS for Optional Third-Party Components, on page

More information

IP phones do not support multicast at 224.x.x.x addresses.

IP phones do not support multicast at 224.x.x.x addresses. Prerequisites for, on page 1 Restrictions for, on page 1 Information About, on page 2 Configure, on page 7 Feature Information for, on page 26 Prerequisites for For Unified CME Release 11.6 and previous

More information

Contents. ETM System v4.0 Minimum System and Network Requirements 2

Contents. ETM System v4.0 Minimum System and Network Requirements 2 Contents ETM System v4.0 Minimum System and Network 2 ETM Software Minimum System...2 Remote TeleView Console Only...2 Complete ETM System Software...3 ETM Server Hardware...4 Data Network...4 Supported

More information

IP Communications High Density Digital Voice/Fax Network Module

IP Communications High Density Digital Voice/Fax Network Module IP Communications High Density Digital Voice/Fax Network Module Document ID: 65356 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Key Features Hardware

More information

Intelligent Inbound Routing

Intelligent Inbound Routing STR Software A Guide to Intelligent Inbound Routing White Paper Intelligent Inbound Routing Enterprise delivery servers, unlike fax machines, are very sophisticated systems that use state-of-the-art technologies

More information

THINKTEL COMMUNICATIONS PATTON SMART NODE 4990 PRI OVER IP SIP TRUNKING

THINKTEL COMMUNICATIONS PATTON SMART NODE 4990 PRI OVER IP SIP TRUNKING THINKTEL COMMUNICATIONS PATTON SMART NODE 4990 PRI OVER IP SIP TRUNKING TA B L E O F C O N T E N T S 1.1 NETWORK DIAGRAM... 3 1.2 CONNECTING THE SMARTNODE TO YOUR PC... 4 1.3 LOGIN TO THE SMARTNODE BY

More information

AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide. Issue /3/2008

AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide. Issue /3/2008 AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide Issue 2.17 3/3/2008 Page 1 of 49 TABLE OF CONTENTS 1 Introduction... 4 2 Special Notes... 4 3 Overview...

More information

Cisco SPA Line IP Phone Cisco Small Business

Cisco SPA Line IP Phone Cisco Small Business Cisco SPA 301 1-Line IP Phone Cisco Small Business Basic, Affordable, IP Phone for Business or Home Office Highlights Basic 1-line business-class IP phone Connects directly to an Internet telephone service

More information

8-Port SIP VoIP Gateway (8 FXS)

8-Port SIP VoIP Gateway (8 FXS) 8-Port SIP VoIP Gateway (8 FXS) Highlights Supports SIP 2.0 (RFC 326) Supports IPv6 and IPv4 simultaneously Up to 24 SIP service domains and Caller ID Supports auto HTTP provision and fax feature Flexible

More information

Configuring the E1 + G.703 and T1 + DSX-1 Modules

Configuring the E1 + G.703 and T1 + DSX-1 Modules 9 Configuring the E1 + G.703 and T1 + DSX-1 Modules Contents Using an E1- or T1-Carrier Line for Data and Voice................... 9-3 Drop-and-Insert Modules..................................... 9-3 Standards

More information

AP-GS808S 8-Port GSM VoIP Gateway High Performance GSM VoIP Gateway Solution

AP-GS808S 8-Port GSM VoIP Gateway High Performance GSM VoIP Gateway Solution AP-GS808S 8-Port VoIP Gateway High Performance VoIP Gateway Solution www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview Hardware Specification Module Specification APOS Technology

More information

Standard 1.2 September 2001

Standard 1.2 September 2001 555-8421-103 Remote Office Network Engineering Guidelines Standard 1.2 September 2001 Copyright 2000 2001 Nortel Networks, All Rights Reserved. Printed in Canada. All information contained in this document

More information

2FXS Analog Telephone Adapter

2FXS Analog Telephone Adapter 2FXS Analog Telephone Adapter Product features Feature-rich telephone service over home or office Internet/ Intranet connection Auto-provisioning features for flexible, ease-of use IP PBX system integration

More information

AP-LMS1500 Multi-Port LMS VoIP Gateway High Performance LMS(Land to Mobile Station) VoIP Gateway

AP-LMS1500 Multi-Port LMS VoIP Gateway High Performance LMS(Land to Mobile Station) VoIP Gateway AP-LMS1500 Multi-Port LMS VoIP Gateway High Performance LMS(Land to Mobile Station) VoIP Gateway Solution Bluetooth VoIP, 3G VoIP Service www.addpac.com AddPac Technology Sales and Marketing Contents Product

More information

Information about IP Proprietary Telephones KX-TDA30/KX-TDA100 KX-TDA200/KX-TDA600. Hybrid IP-PBX. Model No.

Information about IP Proprietary Telephones KX-TDA30/KX-TDA100 KX-TDA200/KX-TDA600. Hybrid IP-PBX. Model No. Information about IP Proprietary Telephones Model No. Hybrid IP-PBX KX-TDA30/KX-TDA100 KX-TDA200/KX-TDA600 Thank you for purchasing a Panasonic Hybrid IP-PBX. Please read this manual carefully before using

More information

AP2620IVR IVR VoIP Gateway High Performance IVR VoIP Gateway Solution

AP2620IVR IVR VoIP Gateway High Performance IVR VoIP Gateway Solution AP2620IVR IVR VoIP Gateway High Performance IVR VoIP Gateway Solution Preliminary Product Overview www.addpac.com AddPac Technology 2006, Sales and Marketing Table of Contents Product Overview Hardware

More information

Initial configuration Vega 400 E1/T1 (SIP)

Initial configuration Vega 400 E1/T1 (SIP) Initial configuration Vega 400 E1/T1 (SIP) R7 This document describes how to configure the Vega 400 E1/T1 SIP unit using the web browser interface. The configuration described will allow the Vega to be

More information

The RFS-105 / RFS-108 is a high-performance Fast Ethernet switch, with all ports capable of 10 or 100Mbps auto-negotiation operation.

The RFS-105 / RFS-108 is a high-performance Fast Ethernet switch, with all ports capable of 10 or 100Mbps auto-negotiation operation. The RFS-105 / RFS-108 is a high-performance Fast Ethernet switch, with all ports capable of 10 or 100Mbps auto-negotiation operation. Store-and-forward switching mode promises the low latency plus eliminates

More information

ABSTRACT. that it avoids the tolls charged by ordinary telephone service

ABSTRACT. that it avoids the tolls charged by ordinary telephone service ABSTRACT VoIP (voice over IP - that is, voice delivered using the Internet Protocol) is a term used in IP telephony for a set of facilities for managing the delivery of voice information using the Internet

More information

Ch. 5 - ISDN - Integrated Services Digital Network

Ch. 5 - ISDN - Integrated Services Digital Network Ch. 5 - ISDN - Integrated Services Digital Network 1 Overview 2 Basic elements in ISDN 3 ISDN - access 4 ISDN - the bus 5 ISDN - examples 6 ISDN - between LAN s 7 ISDN - access to Internet 8 ISDN - small

More information

Programming Guide KX-TDA5480 KX-TDA Channel VoIP Gateway Card. Model

Programming Guide KX-TDA5480 KX-TDA Channel VoIP Gateway Card. Model 4-Channel VoIP Gateway Card Programming Guide Model KX-TDA548 KX-TDA484 Thank you for purchasing a Panasonic 4-Channel VoIP Gateway Card. Please read this manual carefully before using this product and

More information

TT11 VoIP Router 1FXS/1FXO TA User Guide

TT11 VoIP Router 1FXS/1FXO TA User Guide TT11 VoIP Router 1FXS/1FXO TA User Guide Page 1 Table of Contents: 1.0 Introduction... 3 2.0 Package Contents... 3 3.0 Summary of LED & Connector Descriptions... 4 3.1 The Front LEDs... 4 3.2 The Rear

More information

PRImaGate Switch RACK 3U

PRImaGate Switch RACK 3U Up to 32 GSM/UMTS ch. Integrated LCR / Router Voice Call Back SMS Mail Server Up to 64 VoIP channels 4x E1 port (EuroISDN PRI) RACK 3U SMS PRESENTATION Specially designed for big companies, call-centres

More information

IPmux-1E. TDMoIP Gateway FEATURES

IPmux-1E. TDMoIP Gateway FEATURES IPmux-1E FEATURES TDMoIP gateway enabling E1, T1, ISDN, and analog phone communication over asynchronous IP and Ethernet networks Framed (full or fractional) and unframed E1/T1 user traffic Four FXS/E&M/FXO

More information

L2F Case Study Overview

L2F Case Study Overview L2F Case Study Overview Introduction This case study describes how one Internet service provider (ISP) plans, designs, and implements an access virtual private network (VPN) by using Layer 2 Forwarding

More information

VG7000 Digital Gateway

VG7000 Digital Gateway VG7000 Digital Gateway Administrator Installation and Configuration Guide 08VG70M.SG1.00a.EN4 DSG, DSG logo, InterPBX, InterServer, Blaze Series, Savanna Series, VG5000, VG6000, VG7000, IP580, IP500, IP510,

More information

AP-CD Port CDMA VoIP Gateway High Performance CDMA VoIP Gateway Solution

AP-CD Port CDMA VoIP Gateway High Performance CDMA VoIP Gateway Solution AP-CD916 16-Port VoIP Gateway High Performance VoIP Gateway Solution Preliminary Product Overview (Without notice, following described technical spec. can be changed) www.addpac.com AddPac Technology Sales

More information

AP2650PMG PTT Media Gateway High Performance PTT Media Gateway Solution

AP2650PMG PTT Media Gateway High Performance PTT Media Gateway Solution AP2650PMG PTT Media Gateway High Performance PTT Media Gateway Solution Product Overview www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview APOS Technology Hardware Specification

More information

Cisco Unified MeetingPlace Integration

Cisco Unified MeetingPlace Integration CHAPTER 14 This chapter covers system-level design and implementation of Cisco Unified MeetingPlace 5.4 in a Cisco Unified Communications Manager 5.x environment. The following aspects of design and configuration

More information

Spectrum Enterprise SIP Trunking Service Avaya (Nortel) BCM50 Firmware IP PBX Configuration Guide

Spectrum Enterprise SIP Trunking Service Avaya (Nortel) BCM50 Firmware IP PBX Configuration Guide Spectrum Enterprise SIP Trunking Service Avaya (Nortel) BCM50 Firmware 10.0.1.52.176 IP PBX Configuration Guide About Spectrum Enterprise: Spectrum Enterprise is a division of Charter Communications following

More information

VG5000 Analog Voice Gateway

VG5000 Analog Voice Gateway VG5000 Analog Voice Gateway Administrator Installation and Configuration Guide 07VG50M.AG1.08j.EN1 DSG, DSG logo, InterPBX, InterServer, Blaze Series, Savanna Series, VG5000, VG6000, IP580, IP500, InterClient,

More information

Application Notes for Configuring Tidal Communications tnet Business VoIP with Avaya IP Office using SIP Registration - Issue 1.0

Application Notes for Configuring Tidal Communications tnet Business VoIP with Avaya IP Office using SIP Registration - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Tidal Communications tnet Business VoIP with Avaya IP Office using SIP Registration - Issue 1.0 Abstract These Application Notes

More information

Configuring Modem Transport Support for VoIP

Configuring Modem Transport Support for VoIP Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,

More information

VG5000 Analog Voice Gateway

VG5000 Analog Voice Gateway VG5000 Analog Voice Gateway Administrator Installation and Configuration Guide 08VG50M.xg2.00g.EN3 DSG, DSG logo, InterPBX, Blaze, Savanna, VG5000, VG6000, VG7000, IP590, IP580, IP500, IP510, InterConsole,

More information

A more intelligent way to implement VoIP in remote offices and SOHO environments

A more intelligent way to implement VoIP in remote offices and SOHO environments Analog line and trunk interfaces Supports 2 simultaneous VoIP Calls Integrated IP router and firewall Transparent MultiPath Call Routing SelectNet assures superior voice quality A more intelligent way

More information

VoIP Application Note:

VoIP Application Note: VoIP Application Note: Configure NEC UX5000 w/ Excel Telecommunications SIP Trunking Service P/N 0913227 Date: 8/12/09 Table of Contents: GOAL... 3 PREREQUISITES... 3 SIP TRUNKING INFORMATION PROVIDED

More information

This feature was introduced.

This feature was introduced. Feature History Release 12.2(11)T Modification This feature was introduced. This document describes the QSIG for TCL IVR (Tool Language Interactive Voice Response) 2.0 feature in and includes the following

More information

for VoIP Gateway Series

for VoIP Gateway Series Smart Web Manager for VoIP Gateway Series www.addpac.com AddPac Technology 2010, Sales and Marketing Contents Web Connection Main Page Layout System Configuration Language, WAN Setup, LAN Setup, NAT, NTP,

More information

AP1100FN 4-Port FXS 4-Port FXO VoIP Gateway High Performance VoIP Gateway Solution

AP1100FN 4-Port FXS 4-Port FXO VoIP Gateway High Performance VoIP Gateway Solution AP1100FN 4-Port FXS 4-Port FXO VoIP Gateway High Performance VoIP Gateway Solution VoIP Gateway Service + Light SIP Proxy Service www.addpac.com AddPac Technology Sales and Marketing Contents Product Overview

More information

Standalone Voice/IP Gateway Model MVP400 and MVP800. H.323 Mode. Quick Start Guide

Standalone Voice/IP Gateway Model MVP400 and MVP800. H.323 Mode. Quick Start Guide Standalone Voice/IP Gateway Model MVP400 and MVP800 H.323 Mode Quick Start Guide Quick Start Guide 82088202 Revision C MultiVOIP400 (Model MVP400) and MultiVOIP800 (Model MVP800) This publication may not

More information

ISDN Network Side for ETSI Net5 PRI

ISDN Network Side for ETSI Net5 PRI ISDN Network Side for ETSI Net5 PRI Feature History Release 12.1(T) 12.1(5)XM2 Modification This feature was introduced. Support was added for the Cisco AS5350 and Cisco AS5400 universal gateways. This

More information

RMX 2000 Installation & Configuration Guide

RMX 2000 Installation & Configuration Guide RMX 2000 Installation & Configuration Guide General Safety Precautions Follow these rules to ensure general safety: Keep the area around the Polycom RMX 2000 unit clean and free of clutter and well ventilated.

More information

Application Notes for Configuring Windstream SIP Trunking with Avaya IP Office - Issue 1.0

Application Notes for Configuring Windstream SIP Trunking with Avaya IP Office - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Windstream SIP Trunking with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the procedures for configuring

More information

R radio frequency interference, OpenScape Business X3, X5, X8 56 RAS user 291 Reaction Table, Expert mode 1211 Read Communities, Expert mode 1214

R radio frequency interference, OpenScape Business X3, X5, X8 56 RAS user 291 Reaction Table, Expert mode 1211 Read Communities, Expert mode 1214 OpenScape Office, Expert mode 1357 OpenScape Personal Edition 75 OpenStage 75 OpenStage Attendant 648 OpenStage Gate View 961 operating conditions (environmental, mechanical) OpenScape Business S 59 OpenScape

More information

Cisco 4000 Series Integrated Services Router T1/E1 Voice and WAN Network Interface Modules Data Sheet

Cisco 4000 Series Integrated Services Router T1/E1 Voice and WAN Network Interface Modules Data Sheet Data Sheet Cisco 4000 Series Integrated Services Router T1/E1 Voice and WAN Network Interface Modules Data Sheet These flexible interface cards support multiple integrated data and voice applications,

More information