EPTN-OSN Serials Product Brochure

Transcription

1 EPTN-OSN Serials Product Brochure HUAWEI TECHNOLOGIES CO., LTD. Bantian, Longgang District Shenzhen518129, P. R. China Tel: HUAWEI TECHNOLOGIES CO., LTD.

2 Huawei OptiX OSN 7500 II MPLS-TP based Transformer for Metro Aggregation & Core Large Capacity: 320G Packet / 360G TDM universal switch, 16 service processing slots and 16 service interface slots. Ultra Broadband: Smart 40G line transport in one port, 100G line ready. Future-proof: OTN hardware ready. Smart Transport for Multiservice Universal Switch and Transport Smart transport based on universal switch and smart line card for all types of services in any possible mix, including Ethernet, ATM, TDM, and future services. Universal switch at any level of packet and TDM in their original format, high efficiency and best performance, 0 waste of bandwidth. Smart line card for packet and TDM multiservice universal transport in one port, carefree evolution among different types of services, 0 waste of investment. PID inside for Tailored Metro Ultra Broadband Transport Integrating OTU, MUX and DEMUX boards by a PID chip, providing 40G/100G capacity per port and larger in future. SDH-like OAM without complicated photonic layer design such as wavelength planning and OSNR calculating, with less patch cords and fiber operations, time to market greatly reduced. 50% footprint saving and 40% power consumption reduction. Soft Pipe & Hard Pipe for High Reliable and Efficient Transport SDH hard pipe for TDM services with high quality and low delay to ensure reliable transmission for production and dispatching services and private services MPLS-TP based soft pipe supports packet statistical multiplexing to provide high efficient transmission for large bandwidth packet services Universal switch based soft and hard pipes consider both legacy TDM service and future-oriented IP service, so as to achieve smooth evolution for transmission network MPLS-TP based OAM solution TP-Assist providing efficient planning, fast deployment and easy maintenance, making the large-scale Traffic based crystal clear OAM is supported with visual network-level view, graphical format to display end-to-end service configuration, performance and status. Better maintenance experience even than SDH: visualized end-to-end bandwidth management, intelligently locating 92% failure, analyzable and predicable network management Dimensions Switch Capacity Service Slots Supported Interface Networking Mode Operation Environment Ethernet Feature QoS OAM Synchronization OSN 7500 II 800mm (H) x 496mm (W) x 295mm (D) Packet: 320 Gbit/s and TDM: 360 Gbit/s (higher order), 40 Gbit/s (lower order) 32 slots, 16 slots for interface boards and 16 slots for processing boards with same bandwidth per slot 40G interfaces OTU3/40GE, compliant with OTL3.4 standard Ethernet interface FE/GE/10GE/40GE SDH interface STM-1/4/16/64 PDH interface E1/E3/E4; T1/T3/T4 ATM interface E1, STM1 40 DWDM wavelengths, compliant with ITU-T G WDM interface 8 CWDM wavelengths, compliant with ITU-T G Supporting pure packet, hybrid (packet + SDH) or SDH networking Supporting WDM networking -38.4~ -72V DC Temperature Relative Humidity Long term: 0 C ~ 45 C 10% ~ 90% Short term: -5 C ~ 55 C 5% ~ 95% E-Line and E-LAN, QinQ MPLS-TP based VPWS and VPLS Multi-section pseudo-wire (MS-PW) ETH PWE3, TDM PWE3, ATM/IMA PWE3 IGMP Snooping V1/V2/V3 Blacklist, Broadcast packet suppression, ACL VLAN SWAP Committed access rate (CAR), shaping based on port scheduling priority PQ scheduling priority, weighted fair queuing (WFQ) and PQ+WFQ queuing Tail drop and weighted random early detection (WRED) CC, LB, LT AIS, RDI MPLS-TP OAM LM, DM LCK, TST CSF FDI, BDI,CV, FFD, TraceRoute, Ping, LM, DM MPLS OAM PW OAM: CES PW VCCV ETH-CC, ETH-Loopback, ETH-Link Trace, Remote Loopback, Remote Fault Detection, Ethernet OAM RMON(RFC 2819) Universal Cross-Connect, System Control and Clock Processing Board 1+1 backup and Equipment-level power 1+1 backup LSP/PW Linear protection, Ring protection MPLS-TP based Service Anti multifailure protection based on MS-PW LAG, MC-LAG, Dual-homing protection, LPT Mesh and restoration (ASON) SDH based Service 1+1/1:n (n<=14) Linear MSP SNCP/SNCTP 1:N tributary protection for E1/T1, E3/T3, E4, STM-1(e) and FE Both Ethernet and SDH networks supporting clock synchronization Supporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronization Adaptive clock recovery (ACR) Two external clock inputs/outputs (2 MHz or 2 Mbit/s) Two external time signals (1pps+TOD)

3 Huawei OptiX OSN 580 MPLS-TP based Transformer for Metro Access & Aggregation Large Capacity: 280G Packet / 280G TDM universal switch, 14 service slots, 5U height with 19 inch Ultra Broadband: Smart 40G line transport in one port, 100G line ready Future-proof: OTN hardware ready Smart Transport for Multiservice Universal Switch and Transport Smart transport based on universal switch and smart line card for all types of services in any possible mix, including Ethernet, ATM, TDM, and future services. Universal switch at any level of packet and TDM in their original format, high efficiency and best performance, 0 waste of bandwidth. Smart line card for packet and TDM multiservice universal transport in one port, carefree evolution among different types of services, 0 waste of investment. PID inside for Tailored Metro Ultra Broadband Transport Integrating OTU, MUX and DEMUX boards by a PID chip, providing 40G/100G capacity per port. SDH-like OAM without complicated photonic layer design such as wavelength planning and OSNR calculating, with less patch cords and fiber operations, time to market greatly reduced. 50% footprint saving and 40% power consumption reduction. Soft Pipe & Hard Pipe for High Reliable and Efficient Transport SDH hard pipe for TDM services with high quality and low delay to ensure reliable transmission for production and dispatching services and private services MPLS-TP based soft pipe supports packet statistical multiplexing to provide high efficient transmission for large bandwidth packet services Universal switch based soft and hard pipes consider both legacy TDM service and future-oriented IP service, so as to achieve smooth evolution for transmission network Dimensions Switch capacity Networking Mode Operation Environment Ethernet Feature QoS OAM OSN mm (H) x 442mm (W) x 224mm (D) Packet: 280 Gbit/s and TDM: 280 Gbit/s (higher order), 5 Gbit/s (lower order) 14 slots 40G interfaces OTU3/40GE, compliant with OTL3.4 standard Ethernet interface FE/GE/10GE/40GE SDH interface STM-1/4/16/64 PDH interface E1/E3; T1/T3 40 DWDM wavelengths, compliant with ITU-T G WDM interfaces 8 CWDM wavelengths, compliant with ITU-T G Supporting pure packet, hybrid (packet + SDH) or SDH networking Supporting WDM networking DC: -38.4~ -72V DC AC: 100~240V AC Temperature Relative Humidity Long term: 0 C ~ 45 C 10% ~ 90% Short term: -5 C ~ 55 C 5% ~ 95% E-Line,E-LAN and QinQ MPLS-TP based VPWS and VPLS MS-PW ETH PWE3 IGMP Snooping v2/v3 Blacklist, Broadcast packet suppression, ACL Committed access rate (CAR) PQ scheduling priority, weighted round robin (WRR) and PQ+WRR queuing Tail drop and weighted random early detection (WRED) Shaping based on port scheduling priority CC, LB, LT MPLS-TP AIS, RDI OAM LM, DM LCK, TST CSF Ethernet OAM Equipmentlevel MPLS-TP based Service ETH-CC, ETH-Loopback, ETH-Link Trace, Remote Loopback, Remote Fault Detection, RMON (RFC 2819) Universal Cross-Connect, System Control and Clock Processing Board 1+1 backup and power 1+1 backup LSP/PW Linear protection, Ring protection Anti multifailure protection based on MS-PW LAG, MC-LAG, Dual-homing protection, LPT MPLS-TP based OAM solution TP-Assist providing efficient planning, fast deployment and easy maintenance, making the large-scale Traffic based crystal clear OAM is supported with visual network-level view, graphical format to display end-to-end service configuration, performance and status. Better maintenance experience even than SDH: visualized end-to-end bandwidth management, intelligently locating 92% failure, analyzable and predicable network management Synchronization SDH based Service 1+1/1:n (n<=14) Linear MSP; SNCP Both Ethernet and SDH networks supporting clock synchronization Supporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronization Adaptive clock recovery (ACR) Two external clock inputs/outputs (2 MHz or 2 Mbit/s) Two external time signals (1pps+TOD)

4 Huawei OptiX OSN 3580 MPLS-TP based Transformer for Metro Aggregation & Core Large Capacity: 160G Packet / 200G TDM universal switch, 15 service processing slots and 16 service interface slots. Ultra Broadband: Bandwidth smooth evolution with built-in WDM. Future-proof: Packet and TDM services transported by one product. Dimensions Switching capacity Ethernet Feature OSN mm (H) x 497 mm (W) x 295 mm (D) Packet: 160 Gbit/s and TDM: 200 Gbit/s (higher order), 20 Gbit/s (lower order) 15 slots for processing boards and 16 slots for interface boards Packet transport interfaces E1, ch STM-1, ATM STM-1, FE/GE/10GE STM-1/4/16/64, E1/E3/E4/T1/T3, FE/GE/10GE, DDN, IMA/ATM, FEC/EFEC interface, E1 MSTP INTERFACES optical interface, SAN, Video PCM interfaces FXS/FXO, 2/4 wire/e&m, V.35/X.21/V.11/V.24/V.28, RS232/ channel DWDM interfaces, compliant with ITU-T G WDM INTERFACES 8-channel CWDM interfaces, compliant with ITU-T G ~ -72V DC; 110/220V AC (External module) E-Line and E-LAN, QinQ MPLS-TP based VPWS and VPLS Multi-section pseudo-wire (MS-PW) TDM PWE3: CESoPSN and SAToP, compression of idle timeslots ATM/IMA PWE3, ETH PWE3 IGMP SNOOPING V2 Blacklist, Broadcast packet suppression, ACL VLAN SWAP Soft Pipe & Hard Pipe for High Reliable and Efficient Transport SDH hard pipe for TDM services with high quality and low delay to ensure reliable transmission for production and dispatching services and private services MPLS-TP based soft pipe supports packet statistical multiplexing to provide high efficient transmission for large bandwidth packet services Universal switch based soft and hard pipes consider both legacy TDM service and future-oriented IP service, so as to achieve smooth evolution for transmission network Focused on enterprise features Intelligent ASON based Mesh network can against multi-node failures, improving network reliability by 10 times Built-in PCM for real All-in-One solution to access low speed services for enterprise customer Single-span transmission for a distance of 270km without Raman amplifier, less REGs to reduce the network construction cost and facilitates the maintenance MPLS-TP based OAM solution TP-Assist providing efficient planning, fast deployment and easy maintenance, making the large-scale Traffic based crystal clear OAM is supported with visual network-level view, graphical format to display end-to-end service configuration, performance and status. Better maintenance experience even than SDH: visualized end-to-end bandwidth management, intelligently locating 92% failure, analyzable and predicable network management QoS OAM Synchronization Committed access rate (CAR) PQ scheduling priority, weighted fair queuing (WFQ) and PQ+WFQ queuing Tail drop and weighted random early detection (WRED) Eight priority queues Shaping based on port scheduling priority MPLS-TP OAM MPLS OAM Ethernet OAM Equipment-level MPLS-TP based Service SDH based Service CC, LB, LT AIS, RDI LM, DM LCK, TST CSF FDI, BDI CV, FFD, TraceRoute, Ping CES PW VCCV LM, DM Section OAM: CC, LB RDI LM, DM LCK, TST ETH-CC(Continuity Check), ETH-Loopback, ETH-Link Trace Remote Loopback, Remote Fault Detection Universal Cross-Connect, System Control and Clock Processing Board 1+1 backup and power 1+1 backup LSP/PW Linear protection, Ring protection Anti multifailure protection based on MS-PW LAG, MC-LAG, Dual-homing protection, LPT Mesh and restoration (ASON) 1+1/1:n Linear MSP SNCP/SNCTP 1:N tributary protection for E1/T1, E3/T3, E4, STM-1 (e) and FE Both Ethernet and SDH networks supporting clock synchronization Supporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronization Adaptive clock recovery (ACR) Two external clock inputs/outputs (2 MHz or 2 Mbit/s) Two external time signals (1pps+TOD)

5 Huawei OptiX OSN 550 OSN 550 Subrack dimensions Switching capacity Highly reliable design Networking Mode Installation STM-16/4/1&10GE/GE Multi-Service CPE Optical Transmission System Large Capacity: 60G Packet / 20G TDM universal switch, 6 service slots, 2U height with 19 inch Ultra Broadband: 10GE ring in access layer, max 4x10GE Easy Maintenance: AC&DC power supply, flexible installation, working under 65 Small Box with Powerful Function Weight Operation Environment Service features QoS features Easy Maintenance, Excellent Environmental Adaptability Installation at anywhere, wall-mount, desktop, 19 cabinet, 300/600 mm ETSI cabinet, outdoor cabinet Flexible power supply, DC (-48V/-60V)/AC (110V/220V) solution, 10 hours power supply with UPM when the mains supply is interrupted. Work temperature up to 65, can be easily deployed in harsh environment such as outdoor, desert. Hardware-based OAM Humidity 10% ~ 90% 5% ~ 95% E-Line and E-LAN QinQ MPLS-TP based VPWS and VPLS Multi-section pseudo-wire (MS-PW) TDM PWE3: CESoPSN and SAToP, com Carrier-class protection Clock synchronization pression of idle timeslots ATM/IMA PWE3 ETH PWE3 IGMP SNOOPING V2 Blacklist, Broadcast packet suppression, ACL VLAN SWAP Committed access rate (CAR) PQ scheduling priority, weighted round robin (WRR) and PQ+WRR queuing Tail drop and weighted random early detection (WRED) Eight priority queues Shaping based on port scheduling priority MPLS OAM FDI, BDI CC, LB, LT LM, DM MPLS-TP OAM LCK, TST AIS, RDI CSF Ethernet OAM Intelligent power consumption control, idle path power down, intelligent fan speed adjusting. The lowest power consumption, typical power consumption is 30% less than the average in industry. Comply with RoHS/WEEE directive, adopts a variety of technologies to reduce equipment energy, designed according to the requirements of environmental protection. MPLS-TP based OAM solution TP-Assist providing efficient planning, fast deployment and easy maintenance, making the large-scale Traffic based crystal clear OAM is supported with visual network-level view, graphical format to display end-to-end service configuration, performance and status. Better maintenance experience even than SDH: visualized end-to-end bandwidth management, intelligently locating 92% failure, analyzable and predicable network management Temperature Relative Long term: -5 C ~ 55 C Short term: -5 C ~ 65 C Packet Transport Features Smart transport based on universal switch for all types of services, including Ethernet, ATM, TDM, and future services. BIDI and built-in WDM functions to get rid of fiber resources restrict. 2U height, flexible and powerful networking with STM-16/10GE interfaces. Energy Saving, Environmental 88 mm (H) x 442 mm (W) x 220 mm (D) Packet: 60 Gbit/s and TDM: 20 Gbit/s (higher order), 5 Gbit/s (lower order) 6 service interface slots 1+1 hot backup for power supply modules 1+1 hot backup for the system control boards 1+1 hot backup for the cross-connect and synchronous timing boards Packet transport interfaces E1, ch STM-1, ATM STM-1, FE/GE/10GE MSTP interfaces STM-1/4/16, E1/E3/T1/T3, FE/GE 40-channel DWDM interfaces, compliant with ITU-T G WDM interfaces 8-channel CWDM interfaces, compliant with ITU-T G Supporting pure packet, hybrid (packet + SDH) or SDH networking Supporting WDM networking Supportin -38.4~-72V DC; 110/220V AC Wall-mount ETSI rack with 300mm/600mm depth Desktop 19-inch rack Out-door cabinet Net weight of the subrack (no board or fan): 2.78 kg CV, FFD, TraceRoute, Ping CES PW VCCV Section OAM: CC, LB RDI LM, DM LCK, TST ETH-CC(Continuity Check), ETH-Loopback, ETH-Link Trace Remote Loopback, Remote Fault Detection ATM OAM RMON(RFC 2819) Flexible design with multiple protocols LSP/PW Linear protection MPLS-TP Ring protection ERPS(G.8032) Anti multifailure protection based on MS-PW Two external clock inputs/outputs (2 MHz or 2 Mbit/s) Two external time signals (1pps+TOD) Link aggregation group (LAG) protection LPT STP/RSTP/MSTP IMA protection 1+1 and 1:1 Linear MSP Adaptive clock recovery (ACR) Synchronous Ethernet IEEE 1588v2 MSTP Features Carrier-class protection Clock synchronization SDH Network Ethernet Service RSTP, LAG, LPT Two external clock inputs/outputs (2 MHz or 2 Mbit/s) Line clock source Tributary clock source

6 Huawei OptiX OSN 500 (Packet) OSN 500 (Packet) Subrack dimensions Switching capacity Networking Mode Installation Weight Operation Environment GE/FE Multi-Service CPE Optical Transmission System High Integration: 7.2G Packet, 1U height with 19 inch Easy Installation: AC&DC power supply, flexible installation at anywhere High Temperature Resistance: working under 65 Service features Small Box with Powerful Function Smart transport based on universal switch for all types of services, including Ethernet, ATM, TDM, and future services. Single-fiber bidirectional function to get rid of fiber resources restrict. Same platform with OSN 550, board compatible, save spare parts QoS features Easy Maintenance, Excellent Environmental Adaptability SCC unit, cross-connect unit, clock unit, tributary unit, line unit, and data transparent transmission unit integrated in one board, and different device types adapt to different scenarios. Flexible power supply, DC (-48V/-60V)/AC (110V/220V) solution, 10 hours power supply with UPM when the mains supply is interrupted. Work temperature up to 65, can be easily deployed in harsh environment such as outdoor, desert. Energy Saving, Environmental Hardware-based OAM Intelligent power consumption control, idle path power down, intelligent fan speed adjusting. The lowest power consumption, typical power consumption is 30% less than the average in industry. Comply with RoHS/WEEE directive, adopts a variety of technologies to reduce equipment energy, designed according to the requirements of environmental protection. MPLS-TP based OAM solution TP-Assist providing efficient planning, fast deployment and easy maintenance, making the large-scale Traffic based crystal clear OAM is supported with visual network-level view, graphical format to display end-to-end service configuration, performance and status Better maintenance experience even than SDH: visualized end-to-end bandwidth management, intelligently locating 92% failure, analyzable and predicable network management Carrier-class protection Clock synchronization 44mm (H) x 442mm (W) x 220mm(D) Packet: 7.2 Gbit/s 2 service interface slots E1, ch STM-1, ATM STM-1,FE/GE Supporting pure packet networking -38.4~-72V DC 110/220V AC ETSI rack with 300mm/600mm depth Desktop 19-inch rack Out-door cabinet Wall-mount 5 kg Temperature Relative Humidity Long term: -5 C ~ 55 C 10% ~ 90% Short term: -5 C ~ 65 C 5% ~ 95% ATM/IMA PWE3 E-Line and E-LAN ETH PWE3 QinQ IGMP SNOOPING V2 MPLS-TP based VPWS and VPLS Blacklist, Broadcast packet suppression, ACL Multi-section pseudo-wire (MS-PW) VLAN SWAP TDM PWE3: CESoPSN and SAToP, compression of idle timeslots Committed access rate (CAR) PQ scheduling priority, weighted round robin (WRR) and PQ+WRR queuing Tail drop and weighted random early detection (WRED) Eight priority queues Shaping based on port scheduling priority FDI, BDI MPLS OAM CV, FFD, TraceRoute, Ping CES PW VCCV Section OAM: CC, LB CC, LB, LT RDI AIS, RDI MPLS-TP OAM LM, DM LM, DM LCK, TST LCK, TST CSF ETH-CC(Continuity Check), ETH-Loopback, ETH-Link Trace Ethernet OAM Remote Loopback, Remote Fault Detection ATM OAM RMON(RFC 2819) Flexible design with multiple protocols LPT LSP/PW Linear protection STP/RSTP/MSTP MPLS-TP Ring protection IMA protection ERPS(G.8032) 1+1 and 1:1 Linear MSP Anti multifailure protection based on MS-PW Link aggregation group (LAG) protection One external clock input/output (2 MHz or 2 Mbit/s) two external time signals (1pps+TOD) Adaptive clock recovery (ACR) Synchronous Ethernet IEEE 1588v2

7 Huawei OptiX OSN 500 (TDM) OSN 500 (TDM) STM-4/1 Multi-Service CPE Optical Transmission System High Integration: 20G (HO)/20G (LO), 1U height with 19 inch Easy Installation: AC&DC power supply, flexible installation at anywhere High Temperature Resistance: working under 65 Subrack dimensions 44mm (H) x 442mm (W) x 220mm(D) Switching capacity TDM: 20 Gbit/s (higher order), 5 Gbit/s (lower order) 2 service interface slots MSTP interfaces STM-1/4, E1/E3/T1/T3, FE/GE WDM interfaces 40-channel DWDM interfaces, compliant with ITU-T G channel CWDM interfaces, compliant with ITU-T G Networking Mode Supporting pure packet or SDH networking Supporting WDM networking -38.4~-72V DC 110/220V AC Installation ETSI rack with 300mm/600mm depth 19-inch rack Wall-mount Desktop Out-door cabinet Weight 5 kg Operation Environment Temperature Relative Humidity Long term: -5 C ~ 55 C 10% ~ 90% Short term: -5 C ~ 65 C 5% ~ 95% Carrier-class protection SDH Network Small Box with Powerful Function Smart transport based on universal switch for all types of services, including Ethernet, ATM, TDM, and future services. Single-fiber bidirectional function to get rid of fiber resources restrict. Same platform with OSN 550, board compatible, save spare parts Easy Maintenance, Excellent Environmental Adaptability SCC unit, cross-connect unit, clock unit, tributary unit, line unit, and data transparent transmission unit integrated in one board, and different device types adapt to different scenarios. Flexible power supply, DC (-48V/-60V)/AC (110V/220V) solution, 10 hours power supply with UPM when the mains supply is interrupted. Work temperature up to 65, can be easily deployed in harsh environment such as outdoor, desert. Energy Saving, Environmental Intelligent power consumption control, idle path power down, intelligent fan speed adjusting. The lowest power consumption, typical power consumption is 30% less than the average in industry. Comply with RoHS/WEEE directive, adopts a variety of technologies to reduce equipment energy, designed according to the requirements of environmental protection. Ethernet Service RSTP, LAG, LPT Clock synchronization One external clock inputs/outputs (2 MHz or 2 Mbit/s) Line clock source Tributary clock source

8