SOFTWARE INSTALLATION GUIDE. EZSwitchSetup Software Installation Guide for Brocade G620

Transcription

1 SOFTWARE INSTALLATION GUIDE EZSwitchSetup Software Installation Guide for Brocade G May 2016

2 2016, Brocade Communications Systems, Inc. All Rights Reserved. Brocade, Brocade Assurance, the B-wing symbol, ClearLink, DCX, Fabric OS, HyperEdge, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, Vplane, and Vyatta are registered trademarks, and Fabric Vision is a trademark of Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be trademarks of others. Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government. The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the accuracy of this document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that accompany it. The product described by this document may contain open source software covered by the GNU General Public License or other open source license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit

3 Contents EZSwitchSetup Installation...4 Preparing for installation... 4 Downloading EZSwitchSetup...4 Installing the EZSwitchSetup file...5 Running the EZSwitchSetup wizard...9 Configuring the switch...16 Configuring ports and connecting devices

4 Preparing for installation Complete the steps in this guide to install and set up your device in a single-switch configuration using EZSwitchSetup. Refer to the corresponding Hardware Installation Guide if you want to choose a different setup. Before you begin, ensure that you have the items listed in the following tables. Write down the IP network values in the space provided in Table 1. TABLE 1 Configuration information Item Value Fixed IP address (IPv4 or IPv6) for the switch (no DHCP server) Subnet mask value Default Gateway value Brocade switch World Wide Name (WWN) located on the switch ID pullout TABLE 2 Tools and items required for the installation Item Yes/No Ethernet connection (hub or switch) EZSwitchSetup installer download from Host computer with an installed HBA Standard screw driver Browser that allows pop-up windows Ethernet and Fibre Channel cables Setup computer Disk array Optical SFP+ transceivers Downloading EZSwitchSetup The following procedure describes how to download EZSwitchSetup from MyBrocade. 1. Log in to 2. Select downloads. NOTE You must have valid account and login credentials. 3. Under Product Downloads, type "EZSwitch" in the Search field and click Search. The list of EZSwitchSetup releases displays

5 FIGURE 1 EZSwitchSetup download page 4. Click the desired EZSwitchSetup release and select the EZSwitchSetup link for the operating system (Linux or Windows) your host computer is running. The Apple OS X operating system is not supported. The Export Compliance page displays. 5. Review the Export Compliance information, click the certification check box in the Export Compliance page, and click Submit. The Brocade End User License Agreement page displays. 6. Review the Brocade End User License Agreement information and click I Accept in the Brocade End User License Agreement page. 7. Browse to the location you want to save the file and run extract on the.zip file. Installing the EZSwitchSetup file The following procedure describes how to install the EZSwitchSetup file. 1. Navigate to the folder where you extracted the EZSwitchSetup files, and run install.exe. For Windows, this is usually ezswitchsetup(version)\cdrom_installers\windows\disk1\instdata\vm For Linux, this is usually ezswitchsetup(version)\cdrom_installers\linux\disk1\instdata\vm

6 2. Click Next. The Choose Install Folder window appears. 3. Click Next

7 The License Agreement window appears. 4. Select the "I accept the terms of the License Agreement" option and click Install. The installation progress bar is displayed on the window

8 5. Click Done after the installation completes

9 Wait for EZSwitchSetup to start automatically after it is installed. Running the EZSwitchSetup wizard 1. Connect the power cord to the switch and to a power source. The switch power and status LEDs display amber and then green. This can take from one to three minutes. 2. Connect the switch and the setup computer to the same LAN, using Ethernet cables and an Ethernet hub or switch. Be sure the Ethernet hub or switch is connected to a power source. The following figure shows you the connections you need to make to connect cables to the switch. FIGURE 2 Connecting cables to the Brocade G620 switch Power source (1, 6) Ethernet hub or switch (2) Ethernet cables (3, 5) Serial cable shipped with the switch (4) Setup computer COM port (7) 3. If the EZSwitchSetup wizard does not start automatically after installation, go to Start > Programs > EZSwitchSetup and click EZSwitchSetup to run the EZSwitchSetup wizard manually from your PC. In the EZSwitchSetup Introduction window, select the option that matches your setup configuration

10 Use an Ethernet connection to the LAN on the same sub-net as the switch: The option uses the Ethernet LAN connection you will use for running EZSwitchSetup Manager, which is generally more convenient and preferred for running EZSwitchSetup Manager. Use a Serial cable to connect direct to the switch: The option uses a serial cable to connect directly to the switch. If you want to use a serial connection for setup, connect your setup computer COM port to the serial port on the switch, using the serial cable that shipped with the switch. The serial connection settings are as follows: Bits per second: 9600 Databits: 8 Parity: none Stop bits: 1 Flow control: none 4. Click Next. The Connect Cables window is displayed

11 5. Click Next. If you chose to use the serial port connection, the Set Switch IP Address window is displayed. If you chose to use the Ethernet connection, the Discover Switch window is displayed

12 6. Enter the switch WWN, following the instructions on the Discover Switch window and click Next. After completing switch discovery, the discovered switch information is displayed

13 7. Select the Manually assign a new static IP address option and click Next. If you had selected the Keep the current switch IP address option, the Confirm IP Address window is displayed. If you selected the manul option, the Set Switch IP Address window is displayed

14 8. Enter the required information on the Set Switch IP Address window. Click Next. The Confirm IP Address window is displayed

15 9. Click Next. The Continue Configuration? window is displayed

16 10. Select Continue setting up your target switch with EZManager (Recommended) and then click Continue. Click OK in the warning message displayed. A hyperlink to launch EZSwitchSetup is displayed. If prompted to install Active X or a version of the Java runtime environment, do so. Reboot the setup computer, if required. Configuring the switch 1. If the EZSwitchSetup does not launch the Welcome to Switch Configuration window automatically, click the hyperlink to the ezsetup.html file displayed in the browser window. NOTE Sometimes the link to the ezsetup.html file is displayed with the browser window minimized. Enlarge the browser window to see the link

17 The Welcome to Switch Configuration window is displayed. 2. Click Next

18 The Set Parameters window is displayed. 3. Create and enter a new administrator account password, a new name for the switch, and adjust the date and time for your time zone, and click Next. The Select Zoning window is displayed

19 4. Select the Typical Zoning option and click Next. The Specify Devices window is displayed

20 5. Enter the number and types of devices that you are connecting to the switch. EZSwitchSetup uses these values to automatically configure the ports on the switch. 6. Click Next and then install the transceivers and connect the cables. Configuring ports and connecting devices 1. Install the SFP+ transceivers in the Fibre Channel ports on the switch to match the ports as shown in the following figure (SFP+ transceiver installation). a) The 16- and 32-Gbps SFP+ transceivers have a long pull tab and no latching wire bail. Remove any protector plugs from the SFP+ transceivers you are going to use. b) Position and insert each SFP+ transceiver as required (right side up in the top row of ports and upside down in the bottom row of ports). Use the pull tab on the 16- or 32-Gbps SFP+ tranceivers to help push the transceiver into the port. If you are using 16- or 32-Gbps SFP+ transceivers, you may want to connect the cable to the SFP+ transceivers first, and then insert the transceivers into the port as a unit. If you are using 8-Gbps or 10-Gbps SFP+ transceivers, close the latching wire bail

21 NOTE 8-Gbps transceivers are not supported on Brocade G620. c) Repeat for the other ports. FIGURE 3 SFP+ transceiver installation 2. Make the physical connections to your host and storage devices. Match the physical connections shown on the Configure Ports and Connect Devices window. a) Remove any plastic protector caps from the cable ends, and position the cable connector so that it is oriented correctly

22 b) Insert the cable connector into the SFP+ transceivers until it is firmly seated and the latching mechanism clicks. The Configure Ports and Connect Devices window shows missing, valid, and invalid connections as you cable the switch. Note that it can take up to 15 seconds for the connection to display as a valid connection. c) Verify that the connections are all green and click Next. 3. The Finish window displays the message: You have completed the switch setup and the switch is ready to use as configured. To print a summary of these settings, click Print. If you used the serial connection for setup, you can remove the serial cable

23 Refer to the EZSwitchSetup Administrator s Guide for more information on additional switch configuration and management options. If you need assistance, contact your OEM or Solution Provider for all of your product support needs