COSASCO Bluetooth Suite

Transcription

1 COSASCO Bluetooth Suite ER Probe Reader Bluetooth Kit The ER Probe Reader Bluetooth Kit is a convenient and portable standard Electrical Resistance (ER) instrument kit for measuring corrosion rate in any process media. The ER Probe Reader (ER-100) directly connects to ER Standard/Temperature probes*. Measurement readings are displayed and recorded by the Transfer Unit (TU- 500). A cable is only required where access to a probe is difficult and an extension cable is used to position the ER-100 at an easy access location. The ER-100 may be read by the TU-500 from up to 32 ft. (10m) distance with clear line of site. The ER-100 reader replaces the previous Checkmate and CK-4 instrument when used with the TU- 500 Transfer Unit. ER Metal Loss Measurements in any Media Reads all ER standard/temperature probes Rapid measurement cycle Improved resolution Bluetooth Communication Easy data transfer via wireless bluetooth Wireless range up to 32 ft (10m) line of sight No more cables required Quick Data Download 50% faster data download than legacy handhelds Download of data to PC-Wirelessly ER-100 Shown with a 4500 ER Probe Hazardous Area Location Certified Intrinsically safe ( IECEx/ATEX/ C CSA US ) Certified for use in class I, zone 1 IP20 rated enclosure *Some probes require an S to B probe adapter (included)

2 Typical System-High Pressure Transfer Unit ER Probe Reader Probe Adapter High Pressure Retaining Cover Hollow Plug Cosasco Flarweld Access Fitting ER Retrievable Probe ER Corrosion Monitoring Point: High Pressure (up to 6000 psi) The above diagram shows the equipment required for a typical high pressure corrosion monitoring point using electrical resistance measurement technology. A typical ER probe reading system consists of an ER probe connected to a hollow plug and inserted into a Cosasco Access Fitting that has been welded onto the pipeline. The ER probe can be installed and retrieved under full operating pressure using a Cosasco Retriever and Service Valve. The ER-100 Probe Reader and Probe Adapter are placed into the probe. The TU-500 Transfer Unit communicates wirelessly with the ER-100 to take a metal loss reading. Collected readings on the TU-500 can be downloaded wirelessly to a PC running Cosasco Data Offline Software for graphing and analysis.

3 Typical System-Low Pressure ER Probe Reader 1 NPT Nipple Ball Valve Threadolet ER Retractable Probe ER Corrosion Monitoring Point: Low Pressure (up to 1500 psi) The above diagram shows the equipment required for a typical low pressure corrosion monitoring point using electrical resistance measurement technology. The electronic part of the ER Probe reading system works the same as the high pressure system except it does not require a probe adapter between the retractable probe and ER-100 when taking a reading. A standard Threadolet is welded onto the pipeline and a ball valve is installed and remains in situ. A retractable probe is installed and retracted under full operating pressure using a Cosasco Model 60 Retractor Kit.

4 ER-100 Specifications Compatibility Metal Loss Resolution Metal Loss Repeatability Power Source Battery Life All ER standard/temperature probes 0.01% of Probe Span 0.1% of Probe Span 2 AA Lithium Batteries: P/N , alternate P/N (do not mix) 1700 probe readings, typical 2700 probe readings, optimal Temperature Range Operating: -40 o F to 158 o F (-40 o C to 70 o C) Storage: -40 o F to 158 o F (-40 o C to 70 o C) Probe Cable Enclosure Bluetooth Hazardous Area Certification Extension Cables up to 250 ft. (76m) (excludes temperature probes) IP20 Rated 6.69 H x 2.4 W x 1.44 D (17 cm x 6.1 cm x 3.66 cm) Range: 32 ft. (10m), line of sight Communications: Bluetooth Class v2.0 Approvals: FCC/IC/CE 0539 Antenna: Integrated 2 dbi typical, 4 dbi maximum ATEX Certification Sira 14 ATEX 2261X Ex ib IIC T4 Gb, Ta = -40 o C to +70 o C IEC Ex Certification IECEx SIR X Ex ib IIC T4 Gb, Ta = -40 o C to +70 o C North American Certifications CSA Certificate: CSA US Class I, Zone 1, AEx ib IIC T4 Gb, Ta = -40 o C to +70 o C C CSA Ex ib IIC T4 Gb, Ta = -40o C to +70 o C 2.4 in (6.1 cm) 1.44 In. (3.66 cm) 6.69 in (17 cm)

5 TU-500 Specifications Compatibility -All ER and LPR Dataloggers -MICROCOR ER Datalogger -All legacy ER and LPR Remote Data Collectors and MICROCOR ER Dataloggers -ER and LPR Probe Readers -ULTRACORR 2 Reader/Datalogger -Ultracorr Sensors (when used with Ultracorr 2 Reader/Datalogger) Memory Microcor ID s 1-99 and all other ID s Data Transfer Power Source Battery Life Display Bluetooth 2 AA Lithium Batteries: P/N , alternate P/N (do not mix) 4000 probe readings, typical for ER probe readings optimum for ER-100 Four Line Liquid Crystal Display (LCD) Temperature Range Operating: -40 o F to 158 o F (-40 o C to 70 o C) Storage: -40 o F to 158 o F (-40 o C to 70 o C) Enclosure Bluetooth Hazardous Area Certification IP20 rated enclosure with sealed membrane keypad 6.24 H x 3.35 W x.91 D (15.8 cm x 8.51 cm x 2.31 cm) Range: 32 ft. (10m), line of sight Communications: Bluetooth Class v2.0 Approvals: FCC/IC/CE 0539 Antenna: Integrated 2 dbi typical, 4 dbi maximum ATEX Certification SIRA 14 ATEX 2263X Ex ia IIC T4 Ga Ta = -40 o C to +70 o C IEC Ex Certification IECEx SIR X Ex ia IIC T4 Ga Ta = -40 o C to +70 o C North American Certifications CSA Certification: CSA US Class I, Zone 0, AEx ia IIC T4 Ga, Ta = -40 o C to +70 o C C CSA Ex ia IIC T4 Ga, Ta = -40o C to +70 o C 3.35 In. (8.51 cm) 0.91 In. (2.31 cm) 6.24 In. (15.8 cm) 2.87 In. (7.29 cm) 0.88 In. (2.24 cm)

6 Ordering Recommendation Bluetooth Kit Part Number Description ER Probe Reader BT ER Probe Reader, Transfer Unit, S to B Probe Adapter, Test Probe, Batteries*, and User Manual ER Probe Reader with Cosasco Data Offline Software ER Probe Reader plus LPR Probe Reader ER Probe Reader plus LPR Probe Reader with Cosasco Data Offline Software BT BT BT *Batteries for all devices included in package ** See datasheet LPR-100-PR-DS rev- for details on LPR Probe Reader ER Probe Reader, Transfer Unit, S to B Probe Adapter, Test Probe, Batteries*, User Manual, and Cosasco Data Offline Software ER and LPR Probe Reader**, Transfer Unit,S to B Probe Adapter, Test Probe, Batteries*, and User Manual. ER and LPR Probe Reader**, Transfer Unit, S to B Probe Adapter, Test Probe, Batteries*, User Manual, and Cosasco Data Offline Software. Ordering Information Model Description BT ER Probe Reader Bluetooth Kit Code LPR Probe Reader (LPR-100) 0 WIthout LPR Probe Reader 1 With LPR Probe Reader (Standard) Code ER Probe Reader (ER-100) 0 WIthout ER Probe Reader 1 With ER Probe Reader (Standard) Code Legacy Converter (LC-500) 0 Without Legacy Converter 1 With Legacy Converter (Standard) Code Transfer Unit (TU-100) 0 Without Transfer Unit 1 With Transfer Unit Code PC Software 0 Without Cosasco Data Offline 1 With Cosasco Data Offline Code Carrying Case 0 Without Carrying Case 1 With Carrying Case BT Example

7 Accessories and Replacement Parts Part Number Description TU Transfer Unit ER ER Probe Reader LPR LPR Probe Reader S to B Probe Adapter Portable Probe Adapter (for 4000 Series Probes) Carrying Case AA Lithium Battery Standard ER Test Probe Standard LPR Test Probe Extension Cable See ER and LPR Probe Accessories Datasheet Carrying Case Holds Transfer Unit, two Probe Reader Modules and Legacy Converter Cosasco Smith Avenue Santa Fe Springs, CA 90670, USA Tel: sales@cosasco.com Web Site: Rohrback Cosasco Systems, Inc. All rights reserved The contents of this publication are presented for information purposes only, and while effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described wherein or their use or applicability. We reserve the right to modify or improve the designs or specifications of our products at any time without notice. Rohrback Cosasco Systems Corrosion Monitoring Equipment is manufactured and sold under one or more of the following US Patents: , , , , , , , , , , , ER-100-DS rev- A Rev. Date 08/05/2016