Static IP address Dynamic IP address Numer of simmultane connections via Ethernet 1 via masterport 2300, 8 via slave port 2301

Transcription

1 . BUS Ethernet Gateway DS 65L TECHNI This module allows you to communicate with the Luxom system over TCP/IP. You can connect up to 9 devices at the same time. All Luxom modules can be controlled and programmed using the master port: This port allows only one user at the same time. All Luxom modules can be controlled using port: This port allows maximum 8 users at the same time. Benefits : - An even greater flexibility because an existing IP infrastructure can be used. - Uses the international IP standard protocol. - Wireless communication with the Luxom system via WLAN. This module has a configurable TCP/IP address, Default Gateway and Network ID settings. This module has a built-in active termination unit. A wired bridge is required (on the I connector) to activate the internal termination. Your Luxom Bus is operational and ready to communicate via IP as soon as 24VDC is connected to this IP router. 4 TECHNICAL DATA Product ID B3 firmware versi : DS65LI Power supply 24 VDC Power consumption 2.2 VA Installation DIN-rail mount Number of bus connection 3 Screw connector BUS 2.5 mm² Add-on connector 1 or 0 not used Connector LAN (Ethernet) RJ45 10/100 Base-T Hardware protocols TCP, IP, ARP, UDP, ICMP, MAC Active bustermination Yes User ID - password Yes (from PlusConfig 3.2.xx) Static IP address Yes Dynamic IP address Yes Numer of simmultane connections via Ethernet 1 via masterport 2300, 8 via slave port 2301 Warranty 3 year on exchange Ambiant temperature 0-50 C Protection IP 20 Dimensions LxWxH 72 x 90 x 62 mm Number of DIN-rail modules 18 mm 4 CONTROL LEDs I Bus current (extinguishes with short circuit between S and bus wire) U Bus tension (extinguishes with short circuit between + and bus wire) Q1-Q4 N/A with this version I1-I4 N/A with this version 1

2 LOCAL COMMUNICATION CONNECTION VIA CABLE- or - DSL MODEM You need to know the cable/dsl modem s IP address to be able to communicate with a Luxom network from the internet. A standard internet provider s account does not usually provide you with a fixed IP Address. This means you will have to use extra tools to connect to your Luxom environment. For more information please contact your Luxom specialist. In this picture an IP router with built-in modem is used. This is not necessary, and can be two separate devices. WIRELESS CONNECTION (WIFI) WHAT ARE THE ORANGE AND GREEN LED ON THE LAN CONNECTOR FOR? ORANGE LED This LED lights up whenever the module is connected to a LAN network. The module is NOT connected to the LAN network when this LED is not lit. GREEN LED Blinks when there is communication between the module and the LAN network. 2

3 HOW TO CHANGE THE IP SETTINGS FOR MODULE DS65L? This modules default IP address from factory is: Gateway: step procedure to configure the IP address:: 1- Connect the computer to the module with a straight or crossed patch cable: 2- Set the computer s IP address to: Go to your browser (E.g.: Internet Explorer) en type the module s IP address: Press ENTER to make the following screen appear: You'll have to login using: User Name = user Password = luxom The home page of the DS65L opens: see image below. Select Network. 3

4 In this window you can change: IP Adres, Subnet Mask, Default Gateway, Primary DNS, Secondary DNS, Session timeout(*) and Network Id (**) (*) When you fill in 0 sec. as session timeout, there will be no timeout. (**) Network Id (also NID ) is a number that precedes all communication from the DS65L module. (N/A for standard applications) 5- When you ve changed the settings and clicked on, the following message appears: 4

5 This message informs you the module will reboot. The orange and green LEDs on the LAN connector allow you to follow the reboot process. When clicking Apply both LEDs light up after approximately 18 seconds for a period of about 12 seconds. When after this period the orange LED extinguishes for 5 seconds and then lights up again while the green LED starts blinking, the module has fully rebooted. In some cases it can be that you need to power the module down and up again. Note: When changing one of the first 9 digits in the module s IP address, make sure you do the same in your computer s IP address. Neglecting to do so will result in the impossibility to communicate with the module. For example: when you change the module s IP address from to , you also need to change your computer s IP address from to HOW TO FIND THE MODULE S MAC ADDRESS? 1- Download software DS65L_IPconfig from our website, using the following link: You'll need to be logged in to download. If you don't have login yet, you can obtain one by filling in the contact form. Just use the link below Unzip this file and save to you hard drive: c:\ 3- Go to Start/All programs/accessories/command Prompt and type: C:\DS65L_IPConfig/discover push ENTER 4- The following message appears, displaying both the module s IP and MAC address: 5

6 HOW TO FIND THE MODULE S FIRMWARE VERSION? Connect to the module using the PlusConfig software and go to Tools/Options in the menu toolbar: Firmware version: DS65LI

7 HOW TO PASSWORD PROTECT THIS MODULE? Go to: Enter your password twice an click on OK : Available from PlusConfig or higher! This password must be entered every time you whish to connect to the module: If you fail to do so, access will be denied and a lock symbol will appear at the bottom left of your screen. CHANGING THE IP ADDRESS. DS65L with firmware DS65LI 01.xx.xx 1- Download software DS65L_IPconfig from our website as mentioned before. 2- Unzip this file and save to you hard drive: c:\ 3- Go to Start/All programs/accessories/command Prompt and type: C:\DS65L_IPConfig/set /mac=auto /ip= (**) Zie onderstaande afbeelding;!spaces must be entered! 7

8 Using the command above the module s IP address will be changed to Press ENTER The following messages are displayed: "NET+OS Programmer" "Version..." "Copyright..." "Searching for devices. Please wait..." (this might take a moment) "Locate device (auto): Searching for devices. Please Wait..." "Locate device (auto) SUCCESS" "Device has been rebooted" "IP adress has been changed" (this might take a moment) (takes about 20 sec) The IP addess has been changed to Caution: This procedure takes about 1 minute to complete. Please wait until the DOS prompt reappears (c:\). Only then will the module be operational again. (**) In case there is text after C:\, such as C:\Documents and settings\xxx, please type cd\ and push Enter to delete it. Resume step 3. Firmware upgrade Digiconn Download software DS65L_IPconfig from our website using this link: You'll need to be logged in to download. If you don't have login yet, you can obtain one by filling in the contact form. Just use the link below. Download the DS65L upgrade Digiconn file. (image.bin) using this link: Unzip the file and save on you hard disc: c:\ 8

9 Go to Start/All programs/accessories/command Prompt and type: C:\DS65L_IPConfig/discover Press ENTER You will see the IP and the MAC address of the module: (if you already know the IP-adres of the module you can skip this step) For a DS65L with firmware version or older type ftp and the IP address of the module and press enter. To do this your computers IP-address should be in the same range as the IP-address of the module. As user type (none) and press enter. A responce with logged in will appear. Then type bin and press enter, type will be set to 1. After this type put image.bin and press enter. The upgrade will load. To finish type quit and press enter. See image below. 9

10 For a DS65L with firmware version or older type ftp and the IP address of the module and press enter. To do this your computers IP-address should be in the same range as the IP-address of the module. As user type root and press enter. You'll need to give password. The password is Netsilicon (the N of Netsilicon is capital). When you type this you'll notice that this will not appear on your screen. Press enter. You should get password OK. Then type bin and press enter, type will be set to 1. After this type put image.bin and press enter. The upgrade will load. To finish type quit and press enter. See image below. 10