H3C S9500E Routing Switch Series POS Interface Card Datasheet

Transcription

1 H3C S9500E Routing Switch Series POS Interface Card Datasheet Copyright 2012 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. The information in this document is subject to change without notice.

2 Contents Overview 1 Key features 1 PPP/HDLC encapsulation 1 Flexible configuration of interface rate 1 Full-range interfaces 1 Support for SDH and SONET 1 Specifications 2 Card list 2 LSR1DTCP8L1 2 Physical View 2 Technical specifications 2 LEDs 3 Interface cables 3 LSR1DPSP4L1 4 Physical view 4 Technical specifications 4 LEDs 5 Interface cables 5 LSR1DPUP1L1 6 Physical view 6 Technical specifications 6 LEDs 6 Interface cables 7 Environment requirements 7 Safety and regulatory compliance 8 EMC standards 8 ii

3 Overview The H3C S9500E core routing switches (hereinafter referred to as the S9500E switches) are developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred to as H3C). They are new generation core routing switches designed for the core area of campus networks and Internet data centers (IDCs). The S9500E switches provide large-capacity, high-performance Layer 2 and Layer 3 switching services integrated with hardware IPv6, hardware MPLS, security, service analysis, and other intelligent features. The S9500E switches can serve as the basic network platform for the integrated services on campus networks and IDCs, and help integrate users' IT resources. The S9500E switches provide the following POS interface cards: LSR1DPUP1L1 Provides one OC-192c/STM-64c POS optical interface. LSR1DPSP4L1 Provides four OC-48c/STM-16c POS optical interfaces. LSR1DTCP8L1 Provides eight OC-3c/OC-12c multi-rate compatible POS optical interfaces. Key features PPP/HDLC encapsulation The POS interfaces support two types of link encapsulation: PPP and HDLC, and support the configuration of scrambling, CRC-32 or CRC-16, frame format, and path trace bytes. With PPP encapsulation, the POS interfaces support the PAP and CHAP authentication modes. Whether PPP or HDLC encapsulation, the POS interfaces are well compatible with devices of other mainstream manufacturers. Flexible configuration of interface rate The LSR1DTCP8L1 supports configurations of 155 Mbps and 622 Mbps POS interfaces. Full-range interfaces The S9500E switches provide full-range POS interfaces of various rates, including OC-3c, OC-12c, OC-48c, and OC-192c to meet various networking requirements. Support for SDH and SONET The S9500E POS interface cards support Synchronous Digital Hierarchy (SDH) and Synchronous Optical Network (SONET) to enable communications. 1

4 Specifications Card list Table 1 POS interface cards Model LSR1DTCP8L1 LSR1DPSP4L1 LSR1DPUP1L1 Description 8-port OC-3c/OC-12c POS/GE (SFP, LC) optical interface card 4-port OC-48c/STM-16c POS (SFP, LC) optical interface card 1-port OC-192c/STM-64c POS (XFP, LC) optical interface card LSR1DTCP8L1 Physical View Figure 1 Physical view of the LSR1DTCP8L1 Technical specifications Table 2 Technical specifications of the LSR1DTCP8L1 Item Dimensions (H W D) Maximum power consumption Net weight Interface connector type Interface transmission rate Applicable switch models Applicable base cards Specification mm ( in) 30 W 0.36 kg (0.79 Ib) SFP/LC Mbps/ Mbps All S9500E switches LSR1LN1BNL1 and LSR1LN2BNL1 2

5 LEDs Figure 2 Front panel of the LSR1DTCP8L1 (1) Interface LEDs (eight in total) (2) OC-3c/OC-12c SFP optical interfaces (eight in total) Table 3 Interface LED description LEDs Status Description ACT/ALM Red Green Off An alarm is generated. The interface is up, and can transmit and receive data properly. The interface is down. Interface cables The LSR1DTCP8L1 provides eight optical interfaces. You can select SFP transceiver modules as needed. Table 4 Description of OC-3c SFP transceiver modules Model Central wavelength Connector type Fiber Max. transmission distance SFP-FE-SX-MM1310-A 1310 nm LC 1310 nm LC 50/125 μm multi-mode 62.5/125 μm multi-mode 2 km ( km (1.24 SFP-FE-LX-SM1310-A 1310 nm LC SFP-FE-LH40-SM nm LC SFP-FE-LH80-SM nm LC 9/125μm single-mode 15 km ( km ( km (

6 Table 5 Description of OC-12c SFP transceiver modules Model Central wavelength SFP-622M-LX-SM nm LC SFP-622M-LH40-SM nm LC SFP-622M-LH80-SM nm LC Connector type Fiber Max. transmissi on distance 15 km ( km ( km (49.71 LSR1DPSP4L1 Physical view Figure 3 Physical view of the LSR1DPSP4L1 Technical specifications Table 6 Technical specifications of the LSR1DPSP4L1 Item Dimensions (H W D) Maximum power consumption Net weight Description mm ( in) 20 W 0.33 kg (0.73 Ib) Number of interfaces 4 Interface connector type Interface transmission rate Applicable switch models SFP/LC Mbps All S9500E switches 4

7 Item Applicable base cards Description LSR1LN1BNL1 and LSR1LN2BNL1 LEDs Figure 4 Front panel of the LSR1DPSP4L1 (1) ACT/ALM LEDs (four in total) (2) OC-48c/STM-16c SFP optical interfaces (four in total) Table 7 ACT/ALM LED description LED Color Status Meaning On (red) An alarm is generated. ACT/ALM Red/green On (green) The interface is up, and can transmit and receive data properly. Off The interface is down. Interface cables The LSR1DPSP4L1 provides four 2.5G POS optical interfaces. You can select SFP transceiver modules as needed. Table 8 Description of the 2.5G SFP transceiver modules Model Central wavelength SFP-2.5G-LX-SM nm LC SFP-2.5G-LH15-SM nm LC SFP-2.5G-LH40-SM nm LC SFP-2.5G-LH80-SM nm LC Connector type Fiber Max. transmission distance 2 km ( km ( km ( km (

8 LSR1DPUP1L1 Physical view Figure 5 Physical view of the LSR1DPUP1L1 Technical specifications Table 9 Technical specifications of the LSR1DPUP1L1 Item Dimensions (H W D) Maximum power consumption Net weight Description mm ( in) 18 W 0.37 kg (0.82 Ib) Number of interfaces 1 Interface connector type Interface transmission rate Applicable switch models Applicable base cards XFP/LC Mbps All S9500E switches LSR1LN1BNL1 and LSR1LN2BNL1 LEDs Figure 6 Front panel of the LSR1DPUP1L1 (1) ACT/ALM LED (2) OC-192c/STM-64c optical interface 6

9 Table 10 ACT/ALM LED description LED Color Status Meaning On (red) An alarm is generated. ACT/ALM Red/green On (green) The interface is up, and can transmit and receive data properly. Off The interface is down. Interface cables The LSR1DPUP1L1 provides one OC-192c/STM-64c XFP optical interface. You can select a transceiver module as needed. Table 11 Description of the OC-192c/STM-64c XFP transceiver module Model Central wavelength Connector type Fiber Max. transmission distance XFP-LH40-SM1550-F nm LC XFP-LH80-SM nm LC XFP-POS-LH10- SM nm LC 40 km ( km ( km (6.21 Environment requirements Table 12 Temperature, humidity and altitude Item Operating temperature Storage temperature Specification Long-term: 0 C to 45 C (32 F to 113 F) Short-term: 10 C to +55 C (14 F to 131 F) 40 C to +70 C ( 40 F to +158 F) Relative humidity (noncondensing) 5% to 95% Operating altitude Certified operating altitude 4000 m ( ft) 3000 m ( ft) Table 13 Concentration limit of dust Mechanical active material Dust particles per m 3 Limit (No visible dust on the tabletop for three days) NOTE: Dust particle size 5 μm 7

10 The equipment room must be protected against ingression of harmful gases such as SO 2, H 2 S, NH 3, and Cl 2. For the specific requirement, see Table 14. Table 14 Concentration limit of harmful gases Gas Average concentration (mg/m 3 ) Maximum concentration (mg/m 3 ) SO H 2 S NO NH Cl Safety and regulatory compliance EN (LVD Directive) UL IEC EMC standards FCC Part 15 (CFR 47) Class A ICES-003 Class A VCCI Class A GB 9254 Class A CISPR22 Class A EN55022 Class A AS/NZS CISPR22 Class A ETSI EN V1.3.3 CISPR24 EN55024 IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN