Flat. PIFN-C072B Flat 75W LED Driver. Features. Electrical Specifications. Input Specifications 1 / 8 18V - 23V / 2.00A - 3.

Transcription

1 PIFN-C072B Flat 75W LED Driver 18V - 23V / 2.00A A / 75W Features Dimming Method: 0-10V Dimming (0V=10%) Mechanical Outline Constant Current Control (Metal Case) Adjustable Output Current mm Active Power Factor Correction Protection : OVP, SCP and OTP UL 8750, UL 1310, CSA C22.2 No , CSA C22.2 No.223, Class 2 Output Safety Certifications Approved RoHS Compliant Electrical Specifications Output [W] Output [Vdc] Output [A] Input [Vac] Dim. Method PF Efficiency [%] Mechanical Outline [LxWxH mm] V >0.9 Typ Input Specifications Parameter Min. Typ. Max. Unit Remark Input Voltage (Nominal) Vac Input Voltage (Performance) Vac Input Current AC 120V, 100% Load Input Wattage AC 120V, 100% Load Nominal Input Frequency - 50/60 - Hz Efficiency % Power Factor THD AC V, 100% AC V, % AC V, % Load Inrush Current Apk Note : All parameters NOT specially mentioned are measured at rated load and 25 of ambient temperature. 1 / 8

2 Output Specifications Parameter Min. Typ. Max. Unit Remark Output Voltage V Output Current Range A Automatic set by external resistor, Rset Output Dimming Current Range % 0-10V Dimming Output Current Tolerance % Dimming Output Ripple Current % Output Power W = Peak to Peak / 100% Dimming Start-up Time % Dimming Protection Functions Parameter Min. Typ. Max. Unit Remark Output Over Voltage Protection V Latch Off Output Short Circuit Protection A Auto Recovery or Latch Off Output Over Temp. Protection Decrease Tc Environmental Specifications Parameter Min. Typ. Max. Unit Remark Temperature Operation Ta - - Tc Storage Ta Humidity Operation % - Storage % - Lifetime Tc=70 Note : All parameters NOT specially mentioned are measured at rated load and 25 of ambient temperature. 2 / 8

3 Standards Parameter Condition Remark Safety Standards EMI / RFI Standards Design to meet the requirements as follows ; - UL 8750, UL 1310, CSA C22.2 No , CSA C22.2 No Class 2 Output - CE LVD : EN , EN Design to meet the requirements as follows ; - FCC part 15, Class B verification - CE EMCD : EN 55015, EN , EN , EN Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment. 3 / 8

4 Output Current[A] Output Current[A] Flat Dimming Control V Dimming Dim+/- Open Current Driver-max (3.26A, typ.) 0-10V 0-10V dimming curve Short Driver-min (0.326A, typ.) Dimming Voltage[V] 2. Iset-Rset Table (Ta = 25 ) Rset Iset Rset Iset Rset Iset Rset Open Rset Short Rset[Ω] Current Driver-max (3.26A, typ.) Iset-table Driver-min (2A, typ.) 4 / 8

5 Mechanical Outline 1. Case Dimension (Unit: mm) 5 / 8

6 Mechanical Outline 2. Connector Description 2.1 AC Input Connector Item No Name Color AC Input 1 Line Black 2 Neutral White 2.2 DC Output Connector Item No Name Color 1 VLED+ Red 2 VLED- Black DC Output 3 Dim+ Violet 4 Dim- Gray 5 RSET+ Yellow 6 RSET- Yellow Connection Map 6 / 8

7 Caution Storage 1) Suitable for indoor use or outdoor use without direct sunlight exposure 2) This product should not be exposed to sulfur. Transportation 1) Be careful to give mechanical vibration and shock as less as possible and not to drop this product. 2) Static electricity or surge voltage may damage the components inside this product, as such please observe proper anti-electrostatic working process. - People handing the Driver should be well grounded and wear anti-static working clothes and gloves. - All related devices and instruments in the production line should be well grounded. Installation 1) Be careful not to warp or bend this product at assembly. 2) Be careful not to apply stress to the parts such as connectors at assembly. 3) Please note these guidelines and precautions. It is required to be assembled by experienced workers. - Check the power cord is disconnected from the power outlet when this power supply is being installed. - Do not use a damaged input and output lines. If it is damaged, change the power supply through the supplier. - Check the input and output lines are connected correctly. 4) Observe the correct polarity of output terminal. 5) Do not modify this product. It causes a fire and the electric shock. 6) Turn off the power before exchanging LED lamps. 7) The Protective Earth(PE) must be securely connected to Frame Ground(FG) in case the driver is certified with class I (i.e. inclusive of a PE contact) Use Conditions 1) This product must be used within the specification. Any defects or damages resulting from abnormal conditions will not be covered by warranty - In case of the product with latch off function can be shut down under abnormal situations. Under this situation please restart the power supply, after resolving abnormality. 2) This product is for general electronics equipment such as Audio-Visual equipment, household electronics, office supplies, information services and telecommunications; therefore, in case this product is used for medical equipment, space equipment, nuclear equipment or disaster prevention equipment, please contact LG INNOTEK in advance. 3) This product is designed and intended to operate LED loads only. Non-LED loading may be outside the specified design limits of our LED driver, and therefore cannot be covered by the warranty. If you desire to use our product to operate non-led loads please contact us to discuss compatibility. 4) This product is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must re-qualify EMC Directive on the complete installation again. 7 / 8

8 Datasheet Revision History Change Date Rev. No. Description of Change Remark 2014/09/ Initial Release 2015/11/ Page is added - Caution 8 / 8