Flat. PITK-W025B Flat 23W LED Driver. Features. Specification Summary. Input Specifications 1 / V / 0.57A / 23W. Mechanical Outline

Transcription

1 PITK-W025B Flat 23W LED Driver 25-40V / 0.57A / 23W Features Constant Current Control Fixed Output Current Active Power Factor Correction Protection : OVP, SCP KS C 7655 Safety Certifications Approved RoHS Compliant Mechanical Outline (Plastic Case) mm KSA 제 호 Specification Summary Output [W] Output [Vdc] Output [A] Input [Vac] Dim. Method PF Efficiency [%] Mechanical Outline [LxWxH mm] Min. 0.9 Typ x 30 x 25 Input Specifications Input Voltage (Nominal) Vac - Input Voltage (Performance) Vac - Input Current A Typ 220V Input Wattage W Typ 220V Nominal Input Frequency - 50/60 - Hz - Efficiency % Power Factor THD % Typ 220V Please refer to Performance Curve Note: All parameters NOT specially mentioned are measured at rated load and 25 of ambient temperature. 1 / 7

2 Output Specifications Output Voltage % Dimming Output Current A Fixed Current Output Current Tolerance -5-5 % Output Ripple Current - - TBD % Output Power - 23 W Start-up Time - - 1,000 ms Protection Functions Output Over Voltage Protection V Auto Recovery Output Short Circuit Protection A Auto Recovery Environmental Specifications Temperature Humidity Operation Ta - - Tc Storage Ta Operation % - Storage % - Lifetime Ta=50 Note : All parameters NOT specially mentioned are measured at rated load and 25 of ambient temperature. 2 / 7

3 Standards Parameter Condition Remark Safety Standards Design to meet the requirements as follows ; - KS: KS C 7655 EMI / RFI Standards Design to meet the requirements as follows ; - KS: KS C CISPR 15, KS C IEC Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment. 3 / 7

4 Performance Curve 4 / 7

5 Mechanical Outline 1. Case Dimension WIRE SPECIFICATION AC INPUT : KS C IEC SQ, Stranded Wire DC OUTPUT : UL AWG/0.33SQ, Stranded Wire 2. Connection Map RED(LED+) BLACK(LED-) 5 / 7

6 Caution Storage 1) Suitable for indoor use or outdoor use without direct sunlight exposure 2) This product should not be exposed to sulfur. Transportation 1) Be careful to give mechanical vibration and shock as less as possible and not to drop this product. 2) Static electricity or surge voltage may damage the components inside this product, as such please observe proper anti-electrostatic working process. - People handing the Driver should be well grounded and wear anti-static working clothes and gloves. - All related devices and instruments in the production line should be well grounded. Installation 1) Be careful not to warp or bend this product at assembly. 2) Be careful not to apply stress to the parts such as connectors at assembly. 3) Please note these guidelines and precautions. It is required to be assembled by experienced workers. - Check the power cord is disconnected from the power outlet when this power supply is being installed. - Do not use a damaged input and output lines. If it is damaged, change the power supply through the supplier. - Check the input and output lines are connected correctly. 4) Observe the correct polarity of output terminal. 5) Do not modify this product. It causes a fire and the electric shock. 6) Turn off the power before exchanging LED lamps. 7) The Protective Earth(PE) must be securely connected to Frame Ground(FG) in case the driver is certified with class I (i.e. inclusive of a PE contact) Use Conditions 1) This product must be used within the specification. Any defects or damages resulting from abnormal conditions will not be covered by warranty - In case of the product with latch off function can be shut down under abnormal situations. Under this situation please restart the power supply, after resolving abnormality. 2) This product is for general electronics equipment such as Audio-Visual equipment, household electronics, office supplies, information services and telecommunications; therefore, in case this product is used for medical equipment, space equipment, nuclear equipment or disaster prevention equipment, please contact LG INNOTEK in advance. 3) This product is designed and intended to operate LED loads only. Non-LED loading may be outside the specified design limits of our LED driver, and therefore cannot be covered by the warranty. If you desire to use our product to operate non-led loads please contact us to discuss compatibility. 4) This product is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must re-qualify EMC Directive on the complete installation again. 6 / 7

7 Datasheet Revision History Change Date Rev. No. 2015/10/ Initial Release Description of Change Remark 7 / 7