Network Solutions. IVDS Processor Type D (New Specification) Includes:

Transcription

1 360ns Network Solutions IVDS Processor Type D (New Specification) Includes: Traficon VIP3D.x Video Image Processor Card with presence detection, counts, speed, classification, occupancy, density, headway, and gap time IVDS Termination Panel with Surge *Traficon ViewCom/E MAX+ Remote Monitoring, Video Communication and H.264 Streaming module *One ViewCom/E module included per intersection and allows up to 4 inputs

2 VIP3D.1 & VIP3D.2 Vehicle Presence & Data Detector The Original 170, NEMA TS-1 & TS-2 Plug-In Module, 2nd Generation VIP3D.1 & 3D.2 FUNCTIONALITY The VIP3D Video Image Processor provides traffic data and information on the presence of vehicles approaching or waiting at the intersection.» Vehicle presence detection» Traffic data collection: Counts, Speeds, Classification, Occupancy, Density, Headway, Gap time» Alarm events» Wrong way driver detection» Queue length» Turning movement count KEY BENEFITS Presence detection identical to the field-proven VIP3.1 & 3.2 module Data acquisition identical to the field-proven VIP/D module Direct plug-in module for Type 170, NEMA TS-1 & TS-2 controller cabinets VIP3D.2 is a 2-camera unit. 24 outputs and 20 inputs via expansion modules System connection via VIEWCOM/E (Ethernet) VIP3.x Link Software via serial communication RS232 Real time video output on module Data storage on board TRAFFIC DATA ACQUISITION Volume, speed, gap time, headway, occupancy, concentration, classification All data available per lane FLOW MONITORING Distinction between different types of traffic flow Speed drop and wrong-way drivers LOOP EMULATION Pulse output similar to traditional loops in addition to traffic data. VIP3D.2 and Expansion Modules (4 I/O and 2 I/O) Remote image provided by VIEWCOM/E. Virtual vehicle presence detection zones TRAFFIC DATA ACQUISITION The VIP3D provides all relevant traffic data such as volume, speed, gap time, headway, occupancy, concentration and classification. The VIP3D can even store data on board in non-volatile memory. It automatically distinguishes five types of traffic flow (levels of service) based on flow speed and zone occupancy. Within seconds it detects wrong-way drivers or sudden speed variations. LOOP EMULATION Remote image provided by VIEWCOM/E VIP3D can emulate traditional double or single loop detectors. In addition to the traffic data, it provides pulses similar to those provided by inductive loops.

3 VIP3D.1 & VIP3D.2 Vehicle Presence & Data Detector The Original 170, NEMA TS-1 & TS-2 Plug-In Module, 2nd Generation VIP3D.1 & VIP3D.2 PRESENCE & DATA DETECTION» VIP3D.1 monitors 1 camera. VIP3D.2 monitors 2 cameras.» VIP3D.1 provides up to 24 presence detection zones. VIP3D.2 provides up to 20 presence detection zones per camera.» Each presence zone call can be delayed, extended or combined with an input to inhibit the call.» Queue length measurements and directional counts on the intersection.» Combination of outputs and inputs using Boolean functions AND, OR and NOR. VIP3D and Expansion Modules (4 I/O and 2 I/O) Dimensions TS 2 compatible card rack units Serial Ports RS-232C service ports for setup, data collection & firmware update Inputs Composite video 75Ω1Vtt CCIR/EIA Power Supply Reset & recall button on front panel Outputs Analog video output with overlay of system info data & detection zones Auto diagnostic LED indicators VIP3D.2 Main board: 4 optically isolated opencollector outputs Expansion modules 2 I/O & 4 I/O: 2 or 4 digital in/outputs (with dip switches for selection of in/ outputs) Connector Double row 22 pins EDGE (NEMA TS ) Power Supply & Consumption 10.8v to 26.5v DC VIP3D.2 with 200mA at 24v VIP3D.1 with 160mA at 24v 4 I/O with 30mA at 24v DISTRIBUTED BY Environmental -29 F to +165 F (34 C to +74 C) 0 to 95% relative humidity - non-condensing» The VIP 3D.1 provides 8 data detection zones. The VIP 3D.2 provides 4 data detection zones per camera.» Data: count, speed, classification, occupancy, density, headway and gap time.» Generation of alarm events like: speed alarms (4 service levels), speed drop, wrong way driver, queue length threshold and quality alarm.» Double and single data loop simulation.» Per zone, detection can be made direction sensitive.» Single zones can be edited without disturbing the detection.» Each VIP3D can control up to 24 outputs (4 per board and 20 via the I/O extension boards) and 20 inputs (four for each of the five I/O extension boards).» The VIP3D stores up to four configurations per camera.» Internal non volatile memory database.» The VIP3D link software handles o Configuration up and download o Data download (database or individual data monitoring) o Firmware upload via RS232 port o Event download FLOW MONITORING» VIP3D monitors four to eight lanes flow speed between 0 and 100 mph.» VIP3D also monitors the zone occupancy of the detection area.» VIP3D automatically distinguishes five types of traffic flow.» VIP3D detects both wrong-way drivers and sudden speed variations within seconds.» During set-up, alarm levels can be programmed for: o Speed o Speed drop o Occupancy o Image Quality Data subject to alteration without notice or obligation. WESTERN USA: Kar-Gor Inc th Street, S.E. Salem, OR Phone: kargor@aol.com TRAFICON USA: Park Run Drive, Suite 150 Las Vegas, NV Phone: traficon@traficonusa.com EASTERN USA: Control Technologies Inc 2776 South Financial Court Sanford, FL Phone: cttraffic@aol.com

4 VIEWCOM/E MAX+ REMOTE MONITORING, DATA TRANSMISSION, ALARMS, IMAGES AND REAL-TIME MPEG-4 / H.264 STREAMING VIDEO OVER ETHERNET FOR TYPE 170, 2070, NEMA TS1 & TS2 AND ATC CONTROLLERS VIEWCOM/E MAX+ establishes the communication between the VIP detector boards and Flux, the Traficon management system. VIEWCOM/E MAX+ transmits traffic data and events from the VIP detector boards to the PC via Ethernet (TCP/IP) communication. VIEWCOM/E MAX+ also does the compression of images (JPEG) and provides streaming video (MPEG-4/H.264) for remote monitoring and control. In addition, VIEWCOM/E MAX+ handles the communication between the VIP detector boards and the SDLC Interface Device to connect with a TS2 controller. Single slot module VIEWCOM/E MAX+ KEY FUNCTIONALITIES Transmission of data, events and alarms generated by the VIP detector boards IP-addressable communication board JPEG image compression MPEG-4/H.264 streaming video Quad view of 4 cameras for intersection overview Web server with dynamic HTML pages for remote administration Remote and real-time monitoring of the VIP detector boards SNMP network management protocol support A VIEWCOM/E MAX+ board is IP-addressable and communicates via Ethernet. A web server with dynamic HTML pages is running on VIEWCOM/E MAXs with Ethernet communication. The HTML pages provide access to a series of functionalities such as remote monitoring and setup of the VIP detector boards or real-time data reports. This facilitates remote administration. The web server pages are accessible via a standard browser on multiple platforms. KEY BENEFITS Single slot direct plug-in module, rack space saving board Connects via SDLC Interface Device with TS2 controllers Field-proven performance Easy to install, user-friendly setup, high mean time between failures (MTBF) and low mean time to repair (MTTR) Remote monitoring of a VIP detector board via the VIEWCOM/E MAXs homepage

5 PRODUCT SPECIFICATIONS DIMENSIONS 4.5 in H x 1.1 in W x 7.0 in L (114 mm x 28 mm x 178 mm) COMMUNICATION Keypad control port RS-232 communication port RS-485 (polling of the detector boards) Ethernet (TCP/IP) communication Compatible with 170, 2070, NEMA TS1 & TS2 and ATC controllers INPUTS 6 composite video inputs - 1 Vptp RS-170(A) / CCIR Power Supply Reset button on front panel OUTPUTS Composite video (RCA) out with system info Analogue video output with system info Auto diagnostic LED indicators CONNECTOR (back) Double row 22 pins EDGE (NEMA TS ) SYSTEM ARCHITECTURE In a typical installation, the VIP detector boards (single or dual video input) are plugged into a standard cabinet rack. A VIP 2I/Os or 4I/Os expansion module may provide extra inputs and outputs to the VIP detector board. VIEWCOM/E MAX+ transmits data, events and alarms generated by the VIP detector boards to Flux (stand-alone software platform for data collection and storage). Alternatively the VIP detector boards are configured for use with an Interface Device to connect with a TS2 controller using SDLC. In this case, presence detection information is communicated serially to the Interface Device via VIEWCOM/E MAX+. Remote access to VIEWCOM/E MAX+ via the internet browser allows for real-time monitoring of the VIP detector boards (streaming video) and board setup (VIP detector boards and VIEWCOM/E MAX+ board). POWER SUPPLY & CONSUMPTION +10.8V DC to +26,5V DC 24V DC ENVIRONMENTAL -34 C to +74 C 0 to 95% relative humidity - non-condensing NEMA TS2 compliant EMI / EMC FCC Part 15 Class A WESTERN USA: Kar-Gor Inc th Street, S.E. Salem, OR Phone: kargor@aol.com TRAFICON USA: Park Run Drive, Suite 150 Las Vegas, NV Phone: traficon@traficonusa.com EASTERN USA: Control Technologies Inc 2776 South Financial Court Sanford, FL Phone: cttraffic@aol.com DATA SUBJECT TO ALTERATION WITHOUT NOTICE OR OBLIGATION. ISSUE V4-01/2012 KRM