User Programmer Installation Guide
|
|
- Rosemary Green
- 5 years ago
- Views:
Transcription
1 User Programmer Installation Guide The X10DR User Programmer requires two separate programs to be installed. Step 1 Drivers : Install BlueSuite found on the software CD. When given the choice of programs to install please select the options shown below. (Do not install Core, BlueTest3 or DFU tools). X10DR2 User Programmer Installation Instructions_V1.4.docx 1 24/05/ :22 PM
2 Step 2 Programmer : 1. Extract the Programmer to a convenient folder. 2. Start the Programmer from Windows environment: 3. Click OK to the Select Transport prompt: X10DR2 User Programmer Installation Instructions_V1.4.docx 2 24/05/ :22 PM
3 4. Connect the appropriate Programming- Lead (Handset or Gateway) to a PC USB Port. Handset Programming Lead Gateway Programming Lead HANDSET PROGRAMMING: 5. Put the Handset into Programming- Mode by turning it ON whilst holding the PTT Button. i.e. Ensure Handset is OFF, and then hold PTT- button whilst pressing the RED On/Off button. Hear three sets of 2- beeps, and see the LED show RED. You may release the PTT and On/Off button anytime after hearing first beep. 6. Connect the Programming Lead to the Handset. (Note: This may be done before above step if desired). 7. On the Programmer Software : Click on the READ DEVICE button. After approx. 3 seconds a window should show Success 1. Press OK to clear. 8. Make desired changes to the Handset parameters, and click on PROGRAM DEVICE to upload the parameters in the Handset. 9. Click on RESTART button to take the Handset out of Programming- Mode. The Handset can be manually exited from Programming- Mode by briefly pressing the three side buttons simultaneously (e.g. PTT and two BLUE buttons). Hear Power- On beeps from Handset confirming it has exited correctly. 1 If the Programmer fails to READ the device check the Handset LED is RED, then unplug/re- insert USB cable. (This resets the USB connection inside the PC). X10DR2 User Programmer Installation Instructions_V1.4.docx 3 24/05/ :22 PM
4 GATEWAY PROGRAMMING: 10. Put the Gateway into Programming- Mode by inserting the Programming- Lead into the base of the Gateway whilst holding the Gateway s Front- Panel GREY button. See the LED show RED. NOTE: During Programming the RJ45 connector should not be connected. The Programming- Lead supplies the required power to the Gateway during this process. 11. On the Programmer SW : Click on the READ DEVICE button. After approx. 3 seconds a window should show Success 2. Press OK to clear. 12. Make desired changes to the Gateway parameters, and click on PROGRAM DEVICE to save the parameters in the Gateway. 13. There is no need to RESTART the Gateway as it will power- off when the Programming- Lead is removed. 14. Programming is complete. TROUBLESHOOTING If the USB Device fails to install properly 3 perform the following steps: 1. First go into "DEVICES AND PRINTERS"... check if there is a "Generic Bluetooth Device". Right click on it and select "Remove Device". Unplug the X10DR. 2 If the Programmer fails to READ the Gateway, check the Gateway LED is RED, then unplug/re- insert USB cable whilst holding down the Grey Button. (This resets the USB connection inside the PC). 3 This will be evident if the Programmer cannot communicate with the Handset and Gateway. If the Programmer can Read/Program one of the units (Handset or Gateway), then the driver is operating correctly. In this case check cables are properly connected. X10DR2 User Programmer Installation Instructions_V1.4.docx 4 24/05/ :22 PM
5 2. Then go into Windows Explorer and navigate to where BlueSuite was installed : (C:\Program Files (x86)\csr\bluesuite 2.6.2\drivers\win64). 3. Right click on "CSRBlueCoreUSB.inf". Select "Install". 4. Plug in X10DR Handset or Gateway (in programming mode) and check if Device manager now displays "CSR BlueCore in DFU mode". American International Radio(A.I.R.), Inc E. Algonquin Rd. Rolling Meadows, IL 60008, U.S.A. sales@airadio.com X10DR2 User Programmer Installation Instructions_V1.4.docx 5 24/05/ :22 PM
User Programmer Installation Guide
User Programmer Installation Guide The X10DR User Programmer requires two separate programs to be installed. Step 1 Drivers : Install BlueSuite found on the USB Flash- Drive (BlueSuite EXE). When given
More informationUser Programmer Installation Guide
User Programmer Installation Guide The X10DR User Programmer requires two separate programs to be installed. Step 1 Drivers : Install BlueSuite found on the USB Flash- Drive (BlueSuite EXE). When given
More informationFirmware Upgrader Installation And Operation Guide
Firmware Upgrader Installation And Operation Guide Recommended Platform: Windows 7, Windows 10 Introduction: The X10DR2 Firmware Upgrader is used to update the firmware in both the X10DR Gateway and Handset
More informationGateway Audio Level Adjustment Tool. Installation And Operation Guide
Gateway Audio Level Adjustment Tool. Installation And Operation Guide Recommended Platform: Windows 7, Windows 10 Introduction: The X10DR2 Gateway Audio-Level Adjustment Tool is used to adjust the input/output
More informationNX-588E USB Flash Programmer Instructions v1.1
NX-588E USB Flash Programmer Instructions v1.1 Installing the NX-588E on a computer This process should take 5-10 min. 6. The following screen will appear: It is essential you carry out this step from
More information_äìé`çêé _äìépìáíé» User Guide
_äìé`çêé _äìépìáíé» User Guide Issue 3 CSR Cambridge Science Park Milton Road Cambridge CB4 0WH United Kingdom Registered in England 3665875 Tel.: +44 (0)1223 692000 Fax.: +44 (0)1223 692001 www.csr.com
More informationActive Club POS Hardware Setup
Active Club POS Hardware Setup The Active Club POS hardware package includes the following (see figure 1): Heckler stand for ipad APG Vasario 1616 cash drawer Connecting cable for cash drawer Star Micronics
More informationInterpretype Bluetooth Setup Procedure
This information is for configuring the Interpretype to communicate using the Bluetooth Connectivity Kit. To communicate using LAN or Wi-Fi in the full featured version of our software, please refer to
More informationFSU Inventory Scanner Set up & Use for Windows PC
FSU Inventory Scanner Set up & Use for Windows PC FSU Inventory Scanner kit: 1 FSU Property Scanner (Model: CipherLab 8100) 1 Scanner Cradle 1 Scanner Cradle Power Supply 1 USB Cradle to PC Connector Cable
More information1 Introduction. 2 Install the tool. Millennium 2000 M820 ChessGenius Exclusive, PGN. Version:
1 Introduction We want to improve our ChessGenius Exclusive and make it even better. Therefore, we are always happy to receive your feedback at quality@computerchess.com Currently there are two tools for
More informationDP Color LCD Digital Photo Key Chain QUICK SETUP GUIDE
DP161 1.5 Color LCD Digital Photo Key Chain QUICK SETUP GUIDE Getting Started- VERSION DPKEY and 161SX STEP-1-INSTALL The Photo Viewer Software Install the Photo Viewer Software to transfer images to the
More informationInstructions Canton musicbox XS/S Firmware Update
Instructions Canton musicbox XS/S Firmware Update Warning! Warning! Do not connect the musicbox with the PC before you have installed the USB driver supplied with the software, as in this case an incorrect
More informationSTOP! Read these instructions before connecting the PR3 to your Computer
Windows 10 Installation Instructions for the PR3 NOTE: If Windows 10 installed the drivers for the PR3, these instructions are not needed. These instructions are only to be used if Windows 10 did not automatically
More informationPrinter Combo Adapter
Printer Combo Adapter CONFIGURATION UTILITY GUIDE VERSION 1.0 Bluetooth All rights reserved. All trade names are registered trademarks of respective manufacturers listed. The Bluetoothname and the Bluetoothtrademarks
More information1) Installing Bluetooth software for Windows (A) Place installation CD into PC and setup should launch automatically.
1) Installing Bluetooth software for Windows (A) Place installation CD into PC and setup should launch automatically. If setup does not launch, use Windows Explorer to navigate to the appropriate CD- ROM
More informationNetwork USB over IP Server With 1-USB2.0 Port. User Manual V1.0
Network USB over IP Server With 1-USB2.0 Port User Manual V1.0 1 2 TABLE OF CONTENTS COPYRIGHT...4 1. INTRODUCTION...5 PRODUCT OVERVIEW...5 COMPONENTS AND FEATURES...5 HARDWARE INSTALLATION...5 2. THE
More informationCall System. User s Manual
Call System User s Manual User s Manual 13 September 2011 HNS ANDON Call System Copyright 2011 HNS Technical Development Ltd. H-9027 Győr, Gesztenyefa 4. www.hns.eu/spce Phone.: +36 (96) 506-930 Fax: +36
More informationNETCOMM GATEWAY SERIES Dual ADSL2+ / 3G Wireless N Gateway. 3G29WN2 Quick Start Guide
NETCOMM GATEWAY SERIES Dual ADSL2+ / 3G Wireless N Gateway 3G29WN2 Quick Start Guide 1Connecting the cables 4 5 2 4 3 1 4 1. Connect the supplied RJ-11 cable to the DSL port on the back of your device
More informationmce100+ getting started guide Install mce100+ The disc will run and display the below screen: Choose Install mce to continue
content between two the phonebook records of a content from a 1. Insert the mce CD. 2. Choose the Run mce Setup button. The disc will run and display the below screen: Choose mce to continue 5. Ready to
More informationAlphaBeam. Description. Requirements. for PC
AlphaBeam for PC Description AlphaBeam is a software application you install on your computer that lets you beam text from your IR-capable AlphaSmart device to an IR-capable computer. AlphaBeam sends text
More information1 Introduction We want to improve our ChessGenius Exclusive and make it even better. Therefore, we are always happy to receive your feedback at quality@computerchess.com Currently there are two tools for
More informationC75/J75 Simple Image Quality Adjustment (SIQA) v2.0 Software Installation Instructions
C75/J75 Simple Image Quality Adjustment (SIQA) v2.0 Software Installation Instructions Introduction This document support the install of the software for using the new application, called SIQA (Simple
More informationInstallation of advanced communications board and LG Chem RESU
Installation of advanced communications board and LG Chem RESU Introduction This technical note shows how to set up an SP PRO for use with an LG Chem RESU lithium battery. It explains how to update the
More informationALERT2 - Decoder Programming Software Ver. 1.00, MS-DOS.
07-01-2002 ALERT2 - Decoder Programming Software Ver. 1.00, MS-DOS. ALERT2 software is used to program the VEETRONIX 2TR9A decoder. Tones, Tone Timing, Output Timing, and all available decoder options
More informationPacific Sun. User Manual
Pacific Sun User Manual Preface Congratulations on your purchase! Pacific Sun lamps are made with highest quality materials, and made to last! Lamps can be programmed down to finest detail; however there
More informationUPGRADE INSTRUCTIONS
Version 2.48 or 2.49 & Version 3.48 or 3.49 UPGRADE INSTRUCTIONS System Upgrade Requirements NOTE: Non I-Button: V-Sperm Gold version 3.49 must be installed with SQA-V Gold version 2.49. I-Button: V-Sperm
More informationStimulation User s Manual. Version 2.0
Stimulation User s Manual Version 2.0 Triangle BioSystems International 2224 Page Rd. Suite 108 Durham, NC 27703 Phone: (919) 361-2663 Fax: (919) 544-3061 www.trianglebiosystems.com Table of Contents Document
More informationSMART HIFI WIRELESS HEADPHONE. Headblue 2 INSTRUCTION
SMART HIFI WIRELESS HEADPHONE Headblue 2 INSTRUCTION Start here Following items are included 3.5mm audio jack USB cable Product overview 1 2 3 4 5 6 7 9 1. Volume - 2. Volume + 3. Noise reduction mic 4.
More informationDS-101g+ Disk Station Quick Installation Guide
DS-101g+ Disk Station Quick Installation Guide ATTENTION Please refer to Chapter 2 Get to know the Hardware in the User s Guide for the detailed button and LED description. Packing List Before you begin,
More informationPioneer Stealth Touch S-Line (with integrated Epson printer) Installation and Configuration
One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Pioneer Stealth Touch S-Line (with integrated Epson printer)
More information1. Introduction. 2. Installation INSTALLATION INSTRUCTIONS: MCD USB MODULE
Introduction INSTALLATION INSTRUCTIONS: MCD USB MODULE 1. Introduction The USB Module can be used in conjunction with WinMaster to manage Danfoss soft starters. These instructions detail the installation,
More information2.7 Installing the Windows Printer Driver
2.7 2.7.1 USB Driver Installation Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. If not already done, connect power to the printer. Turn power OFF. Connect the USB port on the rear of the printer to the
More informationCONNECTION GUIDE FOR THE IROBOT CREATE
CONNECTION GUIDE FOR THE IROBOT CREATE Pre- Requisites MATLAB 2008 or later needs to be installed on your system. The latest version of MATLAB can be downloaded for free as a Columbia student from the
More informationQUICK GUIDE Connecting your PTT Voice Responder to Talk-IP (Android) (EN)
QUICK GUIDE Connecting your PTT Voice Responder to Talk-IP (Android) (EN) A Pairing your PTT Voice Responder with your smartphone via Bluetooth 1. Turn on your PTT Voice Responder by holding down the Power
More informationInstructions for MX350 Firmware Upload
Instructions for MX350 Firmware Upload MX350 Document AN10048 Page 1 of 39 Contents Section Description Page 1 Requirements 3 2 Install MX350 Setup Software 3 3 Download MX350 Firmware 4 4 Connect MX350
More informationPrint Server. User s Manual. Rev. 01 (April, 2004) Made In Taiwan
Print Server User s Manual Rev. 01 (April, 2004) Made In Taiwan TABLE OF CONTENTS ABOUT THIS GUIDE... 4 INTRODUCTION... 5 PACKAGE CONTENTS... 6 SYSTEM REQUIREMENTS... 6 GENERAL FEATURES... 7 PRODUCT VIEW...
More informationNew Cash Register System Quick Setup Guide. Version: XP1.0
New Cash Register System Quick Setup Guide Version: XP1.0 Contents Quick Step 1 - Upload New Cash Register System End User License... 1 Quick Step 2 Retrieve MAC IDs... 1 Quick Step 3 - Add License Key
More informationEthernet (CAT5 UTP/Straight-Through) Cable. 5V DC Power Adapter
1 This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. Before You Begin Check Your Package Contents DI-824VUP+ 2.4GHz Wireless VPN Router and
More informationUser Manual 1-port USB 2.0 Print Server
User Manual 1-port USB 2.0 Print Server GPSU21W6 PART NO. M1210-b 1 www.iogear.com 2 Welcome Thank you for purchasing this 1-port USB 2.0 Print Server that allows any networked computer to share a USB
More informationQuick USB Start Guide
Quick USB Start Guide To change folders press 2 from the phone keyboard and the screen will show you the folder names you can scroll with SEEK+ and SEEK- Universal Media Interface (UMI) The Universal (UMI)
More informationBT800 Series HID Proxy BT800/BT820
A BT800 Series HID Proxy BT800/BT820 v1.4 INTRODUCTION Laird s BT800 series USB HCI devices support BLE HID proxy mode, a profile designed by Cambridge Silicon Radio that allows Bluetooth Low Energy HID
More informationELAN INTEGRATION WITH THE SHADE STORE MOTORS ELAN INTEGRATION OVERVIEW:
ELAN INTEGRATION WITH THE SHADE STORE MOTORS ELAN INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your ELAN smart home control system. The
More informationzzzzz File Transfer using SafeBridge Page 1
zzzzz File Transfer using SafeBridge Page 1 Contents System requirements... 4 Programming the station... 4 1. Downloading demo codeplugs... 4 2. Unzipping demo codeplugs... 5 3. Open proper codeplug...
More informationIpAlarm Module Set Up
Page 1 IpAlarm Module Set Up Note: This device is shipped configured for Ethernet connectivity. To use in this mode, connect the BLUE Jack (marked WAN) to your router and wait for the LEDs to stabilize.
More informationLab IP Addresses and Network Communication
Lab 3.5.2 IP Addresses and Network Communication Objectives Build a simple peer-to-peer network and verify physical connectivity. Assign various IP addresses to hosts and observe the effects on network
More informationPanoramic Talking Camera
Panoramic Talking Camera IPC2201 home8alarm.com 1-844-800-6482 support@home8alarm.com 1 Table of Contents Chapter 1. Introduction... 1 1.1 System Requirement... 1 Chapter 2. Hardware Overview... 2 Chapter
More informationUser Guide. for Card Reader and Payment Application
User Guide for Card Reader and Payment Application Introduction to Pogo> This document provides detailed information on how best to use the Pogo> application to benefit your business. The intention is
More informationDI-704P Ethernet Broadband Router. Ethernet (Straight Through) Cable. 5V DC Power Adapter
1 This product can be set up using any current Web browser, i.e., Internet Explorer or Netscape Navigator. DI-704P Ethernet Broadband Router and Print Server Before You Begin 1. If you purchased this router
More informationSetting up the PC ready for BESA 11
Setting up the PC ready for BESA 11 1 - Installing Driver. Important Note: Before you start to install the driver, please do not plug BESA 11 into the computer s USB port or else the installation will
More informationDATACARD Firmware Update Instructions. Contents. Firmware Update Application for Windows 98SE Operating Systems. What You Need
DATACARD Firmware Update Instructions Firmware Update Application for Windows 98SE Operating Systems Contents What You Need How to Update Using the Go Green Upgrade CD How to Update Using Files Downloaded
More information8x8 Virtual Office Salesforce Call Center Interface User Guide
8x8 Virtual Office User Guide August 2012 The Champion For Business Communications Table of Contents 8x8 Virtual Office Salesforce Call Center App... 3 System Requirements...3 Installation... 4 Uninstalling
More informationUSER MANUAL for USB Data Link
Driver Installation Under Win 95 OSR2.1 1.Step1: Double click "My Computer" "System Properties" "Device Manager" Step2: While installing USB Data Link Cable under Windows 95 OSR2.1 mode, make sure "Universal
More informationDT810 STOPWATCH WITH PRINTER INSTRUCTION MANUAL. BK233 Printed in China 第一頁
DT810 STOPWATCH WITH PRINTER INSTRUCTION MANUAL www.digisportinstruments.com BK233 Printed in China 第一頁 FEATURES: CHRONOGRAPH 2000 memories Segregated memory (capability to memorize LAP times of different
More informationDatalogging RH / Temperature Pen Instruction Manual
Datalogging RH / Temperature Pen 800013 Instruction Manual 1 Datalogging RH / Temperature Pen 800013 Copyright 2014 by Sper Scientific ALL RIGHTS RESERVED Printed in the USA The contents of this manual
More informationUpgrading Software and Firmware
APPENDIXB This appendix describes how to upgrade or reinstall the Cisco PAM server software, desktop client software, and Gateway module firmware. Contents Upgrade Notes for Release 1.1.0, page B-2 Upgrading
More informationC5150n, C5200ne & C5200n Computer Connections & Software Install Guide
C5150n, C5200ne & C5200n Computer Connections & Software Install Guide Installation Overview: Windows Windows TCP/IP Network Installation: C5150n & C5200ne Ethernet Connection... 2 Software... 3 Windows
More informationPC 3x Software Installation and Operation (TN050312)
PC 3x Software Installation and Operation (TN050312) PC 3x Hardware Description The PC 3x is a compact Peltier cooled inlet system which incorporates the ESI cyclonic spray chamber similar to the existing
More informationUpdating the Nokia E71 software via Nokia Suite
Updating the Nokia E71 software via Nokia Suite Note: A SIM card must be inserted into the phone to upgrade the device. A message will be displayed to the user during the process to insert the card if
More informationNetwork Digital Menu Board Hardware User Manual
Network Digital Menu Board Hardware User Manual Manual Version DMA1 Safety Instructions Please keep the display away from any heat sources. Place the display in a stable and well-ventilated place. Please
More informationMF9300. Software setup guide
MF900 Software setup guide 0000 79-0 S INTRODUCTION This manual explains how to install and configure the software that is required for the printer function of the machine. The procedure for viewing the
More informationSMC Barricade Routers
SMC Barricade Routers User Guide SMC7004BR V1.0 Congratulations on your purchase of the SMC Barricade. The SMC Barricade is a Broadband Router designed to share Internet Access, provide security, and to
More informationGathering Logs from Polycom RealPresence Group Series System and Peripherals
Gathering Logs from Polycom RealPresence Group Series Systems and Peripherals Version 6.1.0 1 Table of Contents Table of Contents... 2 Download or Transfer RealPresence Group System Log Files... 3 Downloading
More informationCRESTRON INTEGRATION WITH THE SHADE STORE MOTORS CRESTRON INTEGRATION OVERVIEW:
CRESTRON INTEGRATION WITH THE SHADE STORE MOTORS CRESTRON INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your Crestron smart home control
More informationUpdate instructions for the MMI 3G+ Update
Update instructions for the MMI 3G+ Update MMI update programming for vehicles equipped with MMI 3G, e.g. the A8 with feedback documentation via Software Versions Management (Audi SVM). Overview of the
More informationTrouble shooting the DeskCNC controller:
Checking for a functional card. 1) Unplug/Disconnect all connections to the I/O and step and direction pins/terminals. 2) Apply regulated 5vdc to the +5 and gnd terminals. CHECK FOR CORRECT POLARITY WITH
More informationPrimex Device Configuration Software Advanced User Guide
Primex Device Configuration Software Advanced User Guide OneVue Wi-Fi & PoE Synchronized Time Solution OneVue is a trademark of Primex. The innovative technology software solution for facility and time
More informationAUA DuoConnect for Notebooks. Installation Guide
R AUA-1422 DuoConnect for Notebooks Installation Guide In this Booklet What s in the Kit 2 System Requirements 2 Installation Overview 3 Step 1: Inserting the Adapter 3 Step 2: Installing the Device Drivers
More informationLogic Controls LV3000 USB Connected Virtual Pole Display on Windows Embedded, Vista, 7
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Logic Controls LV3000 USB Connected Virtual Pole Display on
More informationSoftware Update. Page 1 of 11
Software Update Kit Number None Instruction Sheet This instruction sheet describes how to update the software for Cybex 525X, 62XX, and 77XX model Arc Trainers, Bikes, and. The procedures outlined in the
More informationvideo phone Quick Start Guide
600410 IRIS V video phone Quick Start Guide Getting Started 1 3 2 4 Check to make sure that your box contains each of the items pictured above: 1 IRIS V video phone 2 Handset 3 Ethernet cable (RJ-45) 4
More informationHP AP5000 Installation Guide (XP)
One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 HP AP5000 Installation Guide (XP) This document provides step-by-step
More informationTABLE OF CONTENTS COPYRIGHT INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION
TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3 2. MFP SERVER INSTALLATION...5 PREPARATION...5 CONFIGURATION SOLUTION TABLE...5
More informationiveri NPay HOST SITE INSTALLATION NOTES
iveri NPay HOST SITE INSTALLATION NOTES Step 1 Identify which PC will have the NPay installation with the franchise owner Ensure that the PC is logged on as Administrator. If not ask the franchise owner
More informationCONTROL4 INTEGRATION WITH THE SHADE STORE MOTORS CONTROL4 INTEGRATION OVERVIEW:
CONTROL4 INTEGRATION WITH THE SHADE STORE MOTORS CONTROL4 INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your Savant smart home control
More informationitrax PC Replacement Quick Start Guide P/N Pre-Software Installation
Quick Start Guide P/N 60789-0 Use this procedure to upload the current software onto a new itrax PC. To access the newest software, contact ICS Technical Support at ics.tech.support@nordson.com. Follow
More informationUser Manual Sample. (English version)
BT-2001 v2.5 User Manual Sample (English version) Man & Tel Co., Ltd. [www.manntel.com] SMD-BT2-E025a Copyright Man&Tel 2004 Page 1of 10 Contents I. Hardware 1. Hardware Overview and Functions 3 2. Hardware
More informationIntegration Note. Any feature not specifically noted as supported should be assumed to be unsupported.
Integration Note Manufacturer: Model Number(s): Amazon Fire TV g! Core Module Version: 8.2.650.2 Driver Developer: Intrinsic Group Limited Document Revision Date: 4 th January 2019 Overview & Supported
More informationPractice and Review Activities Software
Practice and Review Activities Software Installation and Setup Procedure Reading Mastery Signature Edition Corrective Reading Installation Insert the Practice and Review Activities CD-ROM into the CD/DVD
More informationUSB 2.0 Print Server. User s Manual. Rev. 01 (Jan, 2004) Made In Taiwan
USB 2.0 Print Server User s Manual Rev. 01 (Jan, 2004) Made In Taiwan TABLE OF CONTENTS ABOUT THIS GUIDE... 4 INTRODUCTION... 5 PACKAGE CONTENTS... 6 SYSTEM REQUIREMENTS... 6 GENERAL FEATURES... 7 PRODUCT
More informationPleiades - NDAS. User Manual. External Storage Enclosure for 3.5 IDE Hard Drives. v1.2
Pleiades - NDAS External Storage Enclosure for 3.5 IDE Hard Drives User Manual v1.2 EN Table of Contents CHAPTER 1 - INTRODUCTION - 1 - CHAPTER 4 - NDAS SETUP - 8 - ICON KEY - 1 - DRIVER INSTALLATION ON
More informationPI Scanner User Guide
PI Scanner User Guide Table of Contents 1. Highlights 2. Overview 3. Installation 3.1. PI Scanner Software Installation 3.2. USB to Serial Interface Board Installation 3.3. Programming the PI Scanner IP
More informationSection 4: Installing the ECC (Epilog Control Center)
Section 4: Installing the ECC (Epilog Control Center) In This Section Installing the ECC The ECC (Epilog Control Center) provides Job Management features as well as laser control and laser machine configuration
More informationUSB SERIAL ADAPTOR COM PORT INSTRUCTIONS
USB SERIAL ADAPTOR COM PORT INSTRUCTIONS No part of this work covered by the copyright hereon may be reproduced, copied, transferred or distributed in any form or by any means -- graphic, electronic, or
More informationInstalling the EPSON U2xx Series Printer using Ethernet Connection Using APD_402E Driver
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Installing the EPSON U2xx Series Printer using Ethernet Connection
More informationQuick Guide. Setting up PNQW1003YA. Model No. KX-TG6322 KX-TG6323 KX-TG6324
TG632x_QG(e).fm Page 1 Thursday, July 17, 2008 10:59 AM Quick Guide Setting up Base unit L Use only the supplied Panasonic AC adaptor PQLV207 or PQLV219. L Use only the supplied telephone line cord. Model
More information5.4.8 Optional Lab: Managing System Files with Built-in Utilities in Windows Vista
5.4.8 Optional Lab: Managing System Files with Built-in Utilities in Windows Vista Introduction Print and complete this lab. In this lab, you will use Windows built-in utilities to gather information about
More informationDIRECT INTERNET 3. User Manual for the Mac OS Operating System
DIRECT INTERNET 3 User Manual for the Mac OS Operating System Iridium Communications Inc. July 2011 Table of Contents 1 OVERVIEW... 1 2 HOW IT WORKS... 1 3 THE DIAL-UP CONNECTION... 2 3.1 Connect... 2
More informationModel No user manual PRO
Model No. 258011 user manual PRO Index Introduction Features Specification Button definition Operation Instruction Power ON/OFF LCD backlight Five main functions PinTest QuickTest Browse Delete Settings
More informationTechnical Bulletin DS2
Product: DS-Matrix Software TB 221 Date: July 25 th, 2012 Subject: How to Upgrade DS-Matrix Software This document describes the procedure for upgrading the DS-Matrix software. If you are upgrading from
More informationUser's Manual V 32.0
User's Manual V 32.0 Trademark Acknowledgements Ford is a registered trademark of Ford Motor Company. Copyright Information DBS User s Manual. 2003, 2004 Ford Motor Company All rights reserved. The information,
More informationINSTALLATION GUIDE. Digital Trunk (Synway) Ver. 3.0
INSTALLATION GUIDE Xtend Voice Logger Digital Trunk (Synway) Ver. 3.0 1. 2. 3. 4. 5. 6. Welcome!!!...3 Introduction...4 Unpacking...6 Minimum System Requirements...6 Interconnection Diagram...7 Getting
More informationUS-IP2. Monitoring Receiver
US-IP2 Monitoring Receiver (and IP receiver card) Programming Manual 28 / 01 / 2014 CONTENT 1. INTRODUCTION...3 2. SYSTEM STRUCTURE...4 3. FIRST STEPS...4 Connectors and LED signals...5 4. SYSTEM PROGRAMMING
More informationXL-NAS-400SA. User s Guide
XL-NAS-400SA User s Guide Table of Contents Chapter 1 Hardware devices 1.1 1.2 1.3 Accessories and XL-NAS-400SA at a glance LCD message and light indicators Hardware installation Chapter 2 Initial setup
More informationQuick Start Guide - XP5s
Quick Start Guide - XP5s INTRODUCTION This Quick Start Guide will outline the steps to set up your Sonim XP5s phone including Linc PTT. Note: If the screen turns off, press the PTT button (grey, left side
More informationQuick Guide for BlueSoleil Version 6
LM540 Bluetooth USB Adapter Quick Guide for BlueSoleil Version 6 1. System Requirements At least 50MB of free disk space is required; Windows 7, Windows Vista or Windows XP operating systems are supported.
More informationField PC 2 Windows OS Update Guide
Field PC 2 Windows OS Update Guide All efforts have been made to ensure the accuracy and completeness of the information contained in this document. RST Instruments Ltd reserves the right to change the
More information8 TS4-DDH T i g e r S t o p M a n u a l D a t a D o w n l o a d i n g. May 2006 Version 3.5 ~ 4.72 Hardware
8 TS4-DDH T i g e r S t o p M a n u a l D a t a D o w n l o a d i n g May 2006 Version 3.5 ~ 4.72 Hardware Installation & User s Guide ESC Ethernet-to-Serial Converter SX Serial Extender IMPORTANT! TigerStop
More informationIpAlarm Module Set Up VirtuAlarm model
Page 1 IpAlarm Module Set Up VirtuAlarm model Note: This device is shipped configured for Ethernet connectivity. To use in this mode, connect the BLUE Jack (marked WAN) to your router and wait at least
More informationHow to Update NN3D to v2.07 (Combo Update) MFDBB
How to Update NN3D to v2.07 (Combo Update) MFDBB 1. NN3D v2.07 Update Introduction MFDBB The combo update for the MFDBB requires a USB Jump Drive (USB flash memory stick). Additionally, a USB KEYBOARD
More informationHooToo IP Camera User Manual(part two)
HooToo Inc. HooToo IP Camera User Manual(part two) For Model: HT-IP210P Published by SunvalleyTek Group 2014/9/14 Content 1. IPCamClient (windows software)...3 Set up...3 CAM... 13 Local Setting... 13
More information