Section 5 Dedicated Timers

Transcription

1 Section 5 Timers Note: DIN Rail Mounting Product pages are not included in this catalog. Go to: Click on the Product Name (ie: CT-SDS) to open the catalog page. [dobe crobat Reader is required] Single Function Delay on Make (ON Delay) Relay Solid State DIN Rail Mounting...see Note above Delay on Make, Normally Closed Solid State Delay on reak (OFF Delay) Relay Solid State DIN Rail Mounting...see Note above True Delay on reak (without auxiliary voltage) Relay...see Note above Solid State...see Note above Single Shot (Pulse Former) Relay Solid State Sequencer Single Shot, Retriggerable (Watchdog, Zero Speed) Relay DIN Rail Mounting...see Note bove Trailing Edge Interval DIN Rail Mounting... see Note bove Interval (Impulse ON) Relay Solid State DIN Rail Mounting... see Note above Recycling & Percentage Relay Solid State Recycling Flashers DIN Rail Mounting... see Note above SQ3 & 4 -- Solid State Dual Function Delay on Make/Delay on reak TDM -- Plug-In DIN Rail Mounting CT-MS.xx... see Note above Delay on Make/Interval ESD5 -- Solid State HVC Timers Solid State TC1 -- nti Short Cycle Random Start T2D -- nti Short Cycle, Random Start TC4 -- ypass Timing T -- nti Short Cycle (DO) TL -- nti Short Cycle (DO) CT -- Fan Delay Vending Timers HRV -- Relay THC/THS -- Solid State KSPU -- Solid State NHPU -- Solid State Star Delta Motor Starting DIN Rail Mounting CT-SDS...see Note above CT-SDE...see Note above CT-YDE...see Note above Low Voltage Products & Systems 5.1

2 Delay On Make (Operate) TDML, TDM, TDMH Series Relay Description The TDM Series is a delay on make timer that combines accurate digital circuitry with isolated DPDT relay contacts in an industry standard 8 pin plug-in package. DIP switch adjustment allows precise selection of the time delay over the full time delay range. The TDM Series is the product of choice for custom control panel and OEM designers. Switch Settable Three Time Ranges from 100 ms... 10,230 s +/-0.1% Repeat ccuracy +/-2% Setting ccuracy DPDT, 10 Contacts LED Indication ** pprovals: ** 8 pin models used in combination with P socket only. ccessories Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Connection Function Delay On Make V = Voltage TD = R = Reset NO = Normally Open NC = Normally Closed = Undefined time Panel mount kit P/N: Z1 Octal 8 pin socket P/N: NDS-8 Hold down clips P/N: PSC8 Relay contacts are isolated. Dashed lines are internal connections. Octal Socket for UL Listing P/N: P DIN rail (Steel) C103PM (l) See accessory pages for specifications. Ordering Table Series/Time Range LED Indication TDML s in 0.1 s increments 12D - 12 V DC L V C TDM s in 1 s increments 24D - 24 V DC/28 V DC TDMH ,230 s in 10 s increments 110D V DC V C V C Example P/N: TDM120L TDM Low Voltage Products & Systems

3 Delay On Make (Operate) TDML, TDM, TDMH Series Relay Technical Data Digital integrated circuitry *For CE approved applications, power Range* s in 0.1 s increments must be removed from the unit when a s in 1 s increments switch position is changed ,230 s in 10 s increments Repeat ccuracy +/-0.1% or 20 ms, whichever is greater Setting ccuracy +/-2% or 50 ms, whichever is greater Reset Time 50 ms Recycle Time During Timing -- TDMH: 500 ms TDM, TDML: 300 ms vs. Temperature & Voltage +/-2% Indicator LED glows during timing; relay is de-energized Voltage 12, 24, or 110 V DC; 24, 120, or 230 V C Tolerance 12 V DC & 24 V DC/C -15% % 110 V C/DC V C -20% % Frequency Hz Power Consumption 2.25 W Electromechanical relay Form Double pole double throw (DPDT) Rating 10 resistive at 120/240 V C & 28 V DC; 1/3 hp at 120/240 V C Life Mechanical -- 1 x10 7 Electrical -- 1 x 10 6 Protection Polarity DC units are reverse polarity protected Isolation Voltage 1500 V RMS input to output Mechanical Mounting Plug-in socket Package 3.2 x 2.4 x 1.8 in. (81.3 x 60.7 x 45.2 mm) Termination Standard octal plug (8 Pin) Environmental Operating Temperature -20 C C Storage Temperature -30 C C Weight 6 oz (170 g) Mechanical View Digi-Set inary Switch Inches (Millimeters) TDM Low Voltage Products & Systems 5.3

4 Delay On Make (Operate) TRM Series Relay Description The TRM Series is a combination of analog electronic circuitry and electromechanical relay output. It provides input to output isolation with a wide variety of input voltages and time ranges. Standard plug-in base wiring, fast reset, rugged enclosure, and good repeat accuracy make the TRM a select choice in any OEM application. Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make 10 DPDT or SPDT Contacts V in Ranges Octal or 11 Pin Plug-in Fixed or djustable Delays from 0.05 to 600 s in ranges +/-2% Repeat ccuracy Hold Down Clamps vailable ** pprovals: ** 8 pin models used in combination with P socket only. Connection 8 Pin Octal DPDT 8 Pin Octal SPDT 11 Pin DPDT V = Voltage TD = R = Reset NO = Normally Open NC = Normally Closed = Undefined time ccessories Octal socket for UL Listing P/N: P pin socket P/N: NDS-11 Hold down clips PSC8 (NDS-8) PSC11 (NDS-11) S1 = Initiate Switch Relay contacts are isolated. Dashed lines are internal connections. R T is used when external adjustment is ordered. Octal 8 pin socket P/N: NDS-8 Panel mount kit P/N: Z1 See accessory pages for specifications. Ordering Table TRM Series djustment and Form Time Tolerance * V C 1 - Fixed, Octal, DPDT - +/-20% (Seconds) 24D - 24 V DC/28 V DC 2 - Knob djust, Octal, DPDT Y - +/-10% D V DC 3 - Lock Shaft djust, Octal, DPDT Z- +/- 5% V C V C 5 - Ext. djust,11 Pin, DPDT without Potentiometer 6 - Ext. djust, 11 Pin, DPDT supplied with Potentiometer Ext. djust, Octal, SPDT, without Potentiometer 9 - Ext. djust, Octal, SPDT, with Potentiometer Example P/N: 5.4 Low Voltage Products & Systems TRM1202Y30 Fixed: TRM12011 *If Fixed Delay is selected, insert delay [ ] in seconds TRM

5 Delay On Make (Operate) TRM Series Relay Technical Data nalog circuitry Range 50 ms m in 15 adjustable ranges or fixed Repeat ccuracy +/-2% or 20 ms, whichever is greater Fixed Time Tolerance & Setting ccuracy +/-5, 10, or 20% Reset Time 50 ms Recycle Time fter timing: 20 ms During timing: 0.1% of max. time delay or 75 ms, whichever is greater vs. Temperature & Voltage +/-10% Voltage 24 or 110 V DC; 24, 120, or 230 V C Tolerance 24 V DC/C -15% % V C/DC -20% % Frequency Hz Power Consumption 2.25 W Electromechanical relay Form Isolated DPDT or SPDT Rating 10 resistive at 120/240 V C & 28 V DC; 1/3 hp at 120/240 V C Life Mechanical: 1 x 10 7 ; Electrical: 1 x 10 6 Protection Isolation Voltage 1500 V RMS between input & output terminals Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Plug-in socket Termination Octal (8 Pin) or 11 Pin plug-in Package 3.62 x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Environmental Operating Temperature -20 C C Storage Temperature -30 C C Weight 6 oz (170 g) Mechanical View Inches (Millimeters) ccessories TRM External adjust potentiometer P1004- (fig. ) P (fig. ) Versa-knob P/N: P External R T P/N Selection Table Figure Value Part Number 1 M ohm 1.5 M ohm 2 M ohm 3 M ohm 5 M ohm 1 M ohm 1.5 M ohm 2 M ohm 3 M ohm 5 M ohm P P P P P P P P P P Low Voltage Products & Systems 5.5

6 Delay On Make (Operate) PRLM Series Relay Description The PRLM Series is designed for use in non-critical timing applications. It offers low cost knob adjustable timing control, full 10 relay output, and onboard LED indication. The knob adjustment provides a guaranteed time range of up to 10 minutes in 6 ranges. The onboard LED indicates whether or not the unit is timing (flashing LED) as well as the status of the output. Knob djustable Relay Electronic Circuit with Electromechanical Relay Popular C & DC Operating Voltages Industry Standard Octal Plug-in Connection s to 600 s in 6 Ranges +/-2% Repeat ccuracy +/-10% Factory Calibration LED Indication 10 Rated DPDT Relay pprovals: ccessories The time delay is initiated when input voltage is applied. LED flashes during timing. t the end of the delay period, the output contacts energize. LED is on steady after the unit times out. Reset: Reset is accomplished by removal of input voltage. There is no false output when reset during timing. Connection Function Delay On Make V = Voltage TD = R = Reset NO = Normally Open NC = Normally Closed = Undefined time Panel mount kit P/N: Z1 Octal 8 pin socket P/N: NDS-8 8 Pin Octal DPDT Relay contacts are isolated. Dashed lines are internal connections. Hold down clips P/N: PSC8 DIN rail (Steel) C103PM (l) See accessory pages for specifications. Ordering Table PRLM Series djustment * 1 - Factory Fixed 2 - djustable Example P/N: 1-12 V DC 2-24 V C 3-24 V DC V C V DC V C PRLM422 Fixed PRLM s s s s s s *If Fixed Delay is selected, insert delay [ ] in seconds. PRLM Low Voltage Products & Systems

7 Delay On Make (Operate) PRLM Series Relay Technical Data nalog circuitry Range s in 6 adjustable ranges or fixed Repeat ccuracy +/-2% or 20 ms, whichever is greater Tolerance Knob djust: Guaranteed range Fixed: +/-10% Reset Time 50 ms Recycle Time fter timing: 20 ms During timing: 0.1% of max. time delay or 75 ms, whichever is greater vs. Temperature & Voltage +/-10% Voltage 24, 120, or 230 V C; 12, 24, or 110 V DC Tolerance 12 V DC & 24 V DC/C -15% % V C/DC -20% % Line Frequency Hz Power Consumption 2.25 W Electromechanical relay Form Isolated DPDT Rating 10 resistive at 28 V DC; 10 resistive at 240 V C; 1/3 hp at 120 & 240 V C Life Mechanical--1x10 7 ; Electrical--1x10 6 Protection Surge IEEE C Level Isolation Voltage 1500 V RMS input to output Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Indication LED During Timing--Flashing Energized--ON steady Mechanical Mounting Plug-in socket Package 3.62 x 2.39 x 1.78 in. (91.6 x 60.7 x 45.2 mm) Termination Octal plug-in (8 pin) Environmental Operating Temperature -20 C C Storage Temperature -30 C C Weight 6 oz (170 g) Mechanical View Inches (Millimeters) PRLM Low Voltage Products & Systems 5.7

8 Delay On Make (Operate) HRDM Power-Time Relay Description The HRDM Series combines an electromechanical relay output with microcontroller timing circuitry. It offers 12 to 230 V operation in five ranges and factory fixed, external, or onboard adjustable time delays with a repeat accuracy of +/-0.5%. The output contact rating allows for direct operation of heavy loads such as compressors, pumps, blower motors, heaters, etc. This series is ideal for OEM applications where cost is a factor. 30 SPDT N.O. Contact V in 5 Ranges Circuitry Delays from 100 ms m in 5 Ranges +/-0.5% Repeat ccuracy Fixed, External, or Onboard djustment pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Connection Function Delay On Make V = Voltage L = Load R = Reset TD = = Undefined time ccessories External adjust potentiometer P (fig ) P (fig ) Mounting bracket P/N: P Female quick connect P (WG 14/16) P (WG 10/12) Quick connect to screw adaptor P/N: P NO = Normally Open L = Load C = Common, Transfer Contact NOTE: knob, or terminals 4 & 5 are only included on adjustable units. RT is used when external adjustment is ordered. Relay contacts are not isolated. Dashed lines are internal connections. Versa-knob P/N: P DIN rail adaptor P/N: P See accessory pages for specifications. DIN rail (Steel) C103PM (l) Ordering Table HRDM Series djustment Time Tolerance * 1-12 V DC 1 - Fixed - +/-1% s 2-24 V C 2 - Onboard lank - +/-5% s 3-24 V DC Knob s V C 3 - External m V C djust m Example P/N: HRDM421 Fixed HRDM410.5S * If Fixed Delay is selected, insert delay [ ] followed by (S) sec. or [ ] (M) min. HRDMGen Low Voltage Products & Systems

9 Delay On Make (Operate) HRDM Power-Time Relay Technical Data Microcontroller circuitry Range 100 ms m in 5 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-1%, +/-5% Reset Time 150 ms vs. Temperature & Voltage +/-2% Voltage 12 or 24 V DC; 24, 120, or 230 V C Tolerance 12 V DC & 24 V DC -15% % V C -20% % Line Frequency Hz Power Consumption C 4 V; DC 2 W Electromechanical relay Form SPDT, non-isolated Ratings: SPDT-N.O. SPDT-N.C. General Purpose 125/240 V C Resistive 125/240 V C V DC Motor Load 125 V C 1 hp* 1/4 hp** 240 V C 2 hp** 1 hp** Life Mechanical -- 1 x 10 6 ; Electrical -- 1 x 10 5, *3 x 10 4, **6,000 Protection Surge IEEE C Level Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 3 x 2 x 1.5 in. (76.7 x 51.3 x 38.1mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating / Storage Temperature -40 C C / -40 C C Humidity 95% relative, non-condensing Weight 3.9 oz (111 g) External Resistance vs Mechanical View Onboard djust Detail Replaces Terminals if Ordered Inches (Millimeters) HRDMGen Low Voltage Products & Systems 5.9

10 Delay On Make (Operate) ERDM Econo-Timer Relay Description Econo-Timers are a combination of digital electronics and a reliable electromechanical relay. These devices offer a DPDT relay output for relay logic circuits, and isolation of input to output voltages. Cost effective for OEM applications such as random starting, sequencing ON, switch de-bouncing, anti-short cycling, and other common delay on make applications. Knob or External djust or Factory Fixed Delays from 0.1 s m +/-0.5% Repeat ccuracy Digital Circuitry 10, Isolated, DPDT Contacts pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make V = Voltage TD = R = Reset NO = Normally Open NC = Normally Closed = Undefined time Connection ccessories External adjust potentiometer P (fig ) P (fig ) Female quick connect P/N: P (WG 14/16) knob, or terminals 9 & 10 are only included on adjustable units. Relay contacts are isolated. Dashed lines are internal connections. RT is used when external adjustment is ordered. Ordering Table Quick connect to screw adaptor P/N: P Versa-knob P/N: P See accessory pages for specifications. ERDM Series djustment * 1-12 V DC 1 - Factory Fixed s 2-24 V C 2 - Knob on Unit s s 3-24 V DC 3 - External djust s V C s V DC s V C m m m m Example P/N: ERDM426 Fixed ERDM410.1S m *If Fixed Delay is selected, insert delay [ ] followed by (S) sec. or (M) min. ERDM Low Voltage Products & Systems

11 Delay On Make (Operate) ERDM Econo-Timer Relay Technical Data Digital integrated circuitry Range 100 ms m in 11 adjustable ranges 100 ms m fixed djustment Knob, external adjust, or fixed Repeat ccuracy +/-0.5% Tolerance (Factory Calibration) +/-10% Recycle Time 150 ms vs. Temperature & Voltage +/-2% Voltage 12, 24, or 120 V DC; 24, 120, or 230 V C Tolerance 12 V DC & 24 V DC/C -15% % 120 V C/DC & 230 V C -20% % Line Frequency Hz Isolated relay contacts Form Double pole double throw (DPDT) Rating 10 resistive at 120/240 V C & 28 V DC; 1/3 hp at 120/240 V C Life Mechanical--1 x 10 7 ; Full Load--1 x 10 6 Protection Isolation Voltage 1500 V RMS input to output Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Surface mount with two #6 (M3.5 x 0.6) screws Termination 0.25 in. (6.35 mm) male quick connect terminals Operating / Storage Temperature -40 C C / -40 C C Weight 5.7 oz (162 g) Mechanical View Inches (Millimeters) ERDM Low Voltage Products & Systems 5.11

12 Delay On Make (Operate) ORM Series Relay Description The ORM Series features open PC board construction for reduced cost. It has isolated 10 DPDT relay contacts and all connections are 0.25 in (6.35 mm) male quick connect terminals. The time delay may be ordered as factory fixed, onboard knob, or external adjustment. Time delays from 0.05 to 300 seconds. Low Cost Open PC Construction s From 50 ms s in 5 Ranges 10 Double Pole Double Throw Relay +/-2% Repeat ccuracy +/-10% Factory Calibration Fixed, djustable on Unit, or External djust pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until voltage is removed. Reset: Removing input voltage resets the time delay and output. Connection Function Delay On Make V = Voltage TD = R = Reset NO = Normally Open NC = Normally Closed = Undefined time ccessories External adjust potentiometer P (fig. ) P (fig. ) Relay contacts are isolated. Dashed lines are internal connections. R T is used when external adjustment is ordered. Female quick connect P/N: P (WG 14/16) Ordering Table Quick connect to screw adaptor P/N: P Versa-knob P/N: P See accessory pages for specifications. ORM Series djustment * V C 1 - Fixed s 24D - 24 V DC/ 28 V DC 110D V DC V C V C 2 - dj. on Unit 3 - Remote djust s s s s Example P/N: ORM2431 Fixed ORM *If Fixed Delay is selected, insert delay [ ] in seconds. ORM Low Voltage Products & Systems

13 Delay On Make (Operate) ORM Series Relay Technical Data nalog circuitry Range s in 5 adjustable ranges or fixed Repeat ccuracy +/-2% or 20 ms, whichever is greater Tolerance (Factory Calibration) djustable: Guaranteed range Fixed: +/-10% Recycle Time 16 ms after timing, during timing % of max. time delay or 75 ms, whichever is greater vs. Temperature & Voltage +/-10% Voltage 24 or 110 V DC; 24, 120, or 230 V C Tolerance 24 V DC/C -15% % V C/DC -20% % Line Frequency Hz Power Consumption 2.25 W Electromechanical relay Form Isolated double pole double throw (DPDT) Rating 10 resistive at 120/240 V C & 28 V DC; 1/3 hp at 120/240 V C Life Mechanical--1x10 7 ; Electrical--1x10 6 Protection Polarity DC units are reverse polarity protected Isolation Voltage 1500 V RMS input to output Mechanical Mounting Surface mount with four #6 (M3.5 x 0.6) screws Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -20 C C Storage Temperature -30 C C Weight 2.7 oz (77 g) Mechanical View Inches (Millimeters) ORM Low Voltage Products & Systems 5.13

14 Delay On Make (ON-Delay) KRDM Digi-Timer Relay Description The KRDM Series is a compact time delay relay measuring only 2 in. (50.8 mm) square. Its solid state timing circuit provides excellent repeat accuracy and stability. Encapsulation protects against shock, vibration, and humidity. The KRDM Series is a cost effective approach for OEM applications that require small size, isolation, reliability, and long life. Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output relay energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make Compact Relay Full 10 SPDT Contacts Onboard or External djust or Fixed Delay Delays from 100 ms m in 5 Ranges +/-0.5% Repeat ccuracy +/-5% Factory Calibration Voltages from V in 5 Ranges pprovals: ccessories Connection V = Voltage TD = R = Reset NO = Normally Open NC = Normally Closed = Undefined time External adjust potentiometer P (fig ) P (fig ) Versa-knob P/N: P V = Voltage C = Common, Transfer Contact NO = Normally Open NC = Normally Closed knob is supplied for adjustable units, or RT terminals 4 & 5 for external adjust. See external adjustment vs time delay chart. Relay contacts are isolated. Dashed lines are internal connections. Mounting bracket P/N: P Ordering Table Female quick connect P (WG 14/16) P (WG 10/12) Quick connect to screw adaptor P/N: P DIN rail (Steel) C103PM (l) KRDM Series djustment * 1-12 V DC 1 - Fixed s 2-24 V C/DC 2 - Onboard s V C djustment s V DC 3 - External m djustment V C m * If Fixed Delay is selected, insert delay [ ] followed by (S) sec. or [ ] (M) min. Example P/N: KRDM421 = 120 V C; Onboard adjust from 0.1 to 10 seconds KRDM610.5S = 230 V C; Fixed at 0.5 seconds DIN rail adaptor P/N: P See accessory pages for specifications. KRDMGen Low Voltage Products & Systems

15 Delay On Make (ON-Delay) KRDM Digi-Timer Relay Technical Data Range 0.1 s m in 5 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-5% Recycle Time 150 ms vs. Temperature & Voltage +/-5% Voltage 12, 24 or 110 V DC; 24, 120 or 230 V C Tolerance 12 V DC & 24 V C/DC -15% % 110 V DC 120 & 230 V C -20% % C Line Frequency/DC Ripple Hz / 10% Power Consumption C 2 V; DC 2 W Isolated relay contacts Form Single pole double throw (SPDT) Rating (at 40 C) 10 resistive at 125 V C 5 resistive at 230 V C & 28 V DC; 1/4 hp at 125 V C Max. Switching Voltage 250 V C Life (s) Mechanical -- 1 x 10 7 ; Electrical -- 1 x 10 5 Protection Circuitry Isolation Voltage 1500 V RMS input to output Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating / Storage Temperature -20 C C / -40 C C Humidity 95% relative, non-condensing Weight 2.6 oz (74 g) Current/mbient Temp. External Resistance vs Mechanical View External djust Detail Replaces Knobs if Ordered Inches (Millimeters) KRDMGen Low Voltage Products & Systems 5.15

16 Delay On Make (Operate) TDU, KSDU Digi-Set Timing Modules Description The TDU and KSDU Series are encapsulated solid state delay on make that combine digital timing circuitry with universal voltage operation. The TDU offers DIP switch adjustment allowing accurate selection of the time delay over the full time delay range. The KSDU is factory fixed from 0.1 s to 10,230 s and does not include the DIP switch. These series are excellent choices for process control systems and OEM equipment. 2 Universal Voltage Ranges From V C/DC Digital Integrated Circuitry Switch Selectable Delays From 0.1 s h in 3 Ranges or Factory Fixed +/-0.5% Repeat ccuracy 1 Steady - 10 Inrush Totally Solid State and pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Connection Function Delay On Make V = Voltage R = Reset TD = L = Load = Undefined time ccessories Female quick connect P/N: P (WG 14/16) Dashed lines are internal connections. Load may be connected to terminal 3 or 1. TDU has DIP switch adjustment; KSDU is fixed. Quick connect to screw adaptor P/N: P Ordering Table Mounting bracket P/N: P TDU Series Voltage Range C/DC C/DC C/DC C/DC C/DC C/DC Time Range - Seconds Part Number TDUL3000 TDUL3001 TDU3000 TDU3001 TDUH3000 TDUH3001 DIN rail (Steel) C103PM (l) KSDU Series Voltage Range (Seconds) V C/DC 1 - Fixed Specify fixed delay in V C/DC seconds DIN rail adaptor P/N: P See accessory pages for specifications. Example P/N: KSDU81300, KSDU910.1 TDKSDU Low Voltage Products & Systems

17 Delay On Make (Operate) TDU, KSDU Digi-Set Timing Modules Technical Data Digital integrated circuitry Range* djustable (TDU) s in 0.1 s increments s in 1 s increments s in 10 s increments Fixed (KSDU) Fixed from 0.1 s...10,230 s Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-10% Recycle Time 150 ms vs. Temperature & Voltage +/-5% Voltage V C/DC V C/DC Line Frequency Hz Tolerance +/-20% Solid state Form Normally Open, open during timing Maximum Load Current 1 steady state, 10 inrush at 60 C Minimum Holding Current 40 m Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -40 C C Storage Temperature -40 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) * For CE approved applications, power must be removed from the unit when a switch position is changed. TDU djustment Digi-Set inary Switch Mechanical View Inches (Millimeters) djustment Switches Shown Not Included on KSDU Series. TDKSDU Low Voltage Products & Systems 5.17

18 Delay On Make (Operate) TMV8000/TSU2000 Uni-Timer Timing Module Description The TMV and TSU Series are universal voltage delay on make. Two models cover all the popular voltages and time delays. vailable with knob or external adjust time delay. Its simple two terminals can easily be connected in series with a relay coil, contactor coil, solenoid, lamps, small motor, etc., to delay their energization, prevent short cycling or to sequence on various loads. TMV8000 Operates From V C/DC Knob or External djust s Delays from m Totally Solid State - 1 Steady - 10 Inrush Two Terminal Series Connection with Load pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Connection Delay On Make V = Voltage L = Load R = Reset TD = = Undefined time ccessories External adjust potentiometer P (fig ) P (fig ) Mounting bracket P/N: P Female quick connect P/N: P (WG 14/16) Load may be connected to terminal 3 or 1. TMV has knob adjustment. TSU has external adjustment terminals 4 & 5. Quick connect to screw adaptor P/N: P Versa-knob P/N: P Ordering Table DIN rail (Steel) C103PM (l) djustment V C/DC s External V C/DC m Knob Part Number TSU2000 TMV8000 DIN rail adaptor P/N: P See accessory pages for specifications. TMV Low Voltage Products & Systems

19 Delay On Make (Operate) TMV8000/TSU2000 Uni-Timer Timing Module Technical Data nalog circuitry Range s (TSU2000) m (TMV8000) Repeat ccuracy +/-2% Tolerance (Factory Calibration) +/-10% Reset Time 100 ms Voltage V C/DC +/-20% Line Frequency Hz Solid State Form Normally Open, open during timing Maximum Load Current 1 steady state, 10 inrush at 55 C Minimum Holding Current 40 m Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -20 C C Storage Temperature -30 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) TSU2000 Mechanical View Inches (Millimeters) TMV has the knob and dial. TSU has terminals 4 & 5. TMV Low Voltage Products & Systems 5.19

20 Delay On Make (Operate) TSD1 Digi-Timer Timing Module Description The TSD Series is designed for more demanding commercial and industrial applications where small size, and accurate performance is required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available. The output is rated 1 steady and 10 inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Fixed or djustable Delays From 0.1 s h +/-0.1% Repeat ccuracy +/-1% Factory Calibration V in 6 Ranges 1 Solid State Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make V = Voltage L = Load R = Reset TD = = Undefined time pprovals: Connection ccessories External adjust potentiometer P (fig ) P (fig ) Mounting bracket P/N: P Female quick connect P/N: P (WG 14/16) Load may be connected to terminal 3 or 1. R T is used when external adjustment is ordered. Dashed lines are internal connections. Quick connect to screw adaptor P/N: P DIN rail adaptor P/N: P Versa-knob P/N: P DIN rail (Steel) C103PM (l) See accessory pages for specifications. Ordering Table TSD1 Series djustment * 1-12 V DC 1 - Fixed s 2-24 V C 2 - External s 3-24 V DC djust s V C 3 - Onboard m V DC djust m V C m h Example P/N: TSD1421 Fixed TSD1410.5S *If Fixed Delay is selected, insert delay [ ] followed by (S) secs. or (M) mins., or [1 100] (H) hours. TSD1Gen Low Voltage Products & Systems

21 Delay On Make (Operate) TSD1 Digi-Timer Timing Module Technical Data Range 0.1 s h in 7 adjustable ranges or fixed Repeat ccuracy +/-0.1% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-1% Recycle Time 150 ms vs. Temperature & Voltage +/-1% Voltage 12, 24, 120 V DC; 24, 120, 230 V C Tolerance +/-20% Line Frequency Hz Solid state Form Normally Open, open during timing Maximum Load Current 1 steady state, 10 inrush at 60 C Minimum Holding Current 40 m Off State Leakage Current 7 m at 230 V C Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -40 C C Storage Temperature -40 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) External Resistance vs Mechanical View Fixed & External djust Onboard djust TSD1Gen Inches (Millimeters) Low Voltage Products & Systems 5.21

22 Delay On Make (ON-Delay) THDM Digi-Power Power Timing Module Description The THDM Series is a high power solid state delay on make timer that is connected in series withthe load. The THDM eliminates the need for a timer and a spearate solid state relay. cost effective approach for controlling larger loads such as motor, electric heating elements, and lamps. When mounted on a metal surface, it can switch loads up to 20 mps steady, 200 mps inrush. High Load Currents up to 20, 200 Inrush Simple-to-use Two Terminal Series Connection +/- 0.5% Repeat ccuracy Fixed or djustable Delays From 1 s m +/- 10% Factory Calibration 24, 120, or 230 V C Metallized Mounting Surface for Heat Transfer Solid State & pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output is energized and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make V = Voltage L = Load R = Reset TD = = Undefined time Connection ccessories External adjust potentiometer P (fig ) P (fig ) s s m m m VTP P/N VTP5G VTP5K VTP5N VTP5P VTP5R Female quick connect P (WG 14/16) P (WG 10/12) Load may be connected to terminal 3 or 1. R T is used when external adjustment is ordered. Dashed lines are internal connections. Quick connect to screw adaptor P/N: P Ordering Table Versa-knob P/N: P Plug-on adjustment module P/N: VTP()() See accessory pages for specifications. THDM Series djustment * Rating 2-24 V C V C 1 - Fixed 2 - External s s V C djust m C m m Example P/N: THDM621 Fixed THDM210.5MC *If Fixed Delay is selected, insert delay [ ] followed by (S) sec. or [ ] (M) min. THDM Low Voltage Products & Systems

23 Delay On Make (ON-Delay) THDM Digi-Power Power Timing Module Technical Data Digital intergrated circuitry Range 1 s m in 5 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/- 10% Recycle Time During timing ms; fter timing ms vs. Temperature & Voltage +/-2% Voltage 24, 120, or 230 V C Tolerance +/-20% Line Frequency Hz Solid state Form Normally Open, open during timing Maximum Load Currents Steady State Inrush** C Minimum Load Current 100 m Effective Voltage Drop (V Line - V Load) Effective Drop 24 V C 3 V 120 V C 3 V 230 V C 5 V Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting ** Surface mount with one #10 (M5 x 0.8) screw Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating/Storage Temperature -40 C C / -40 C C Humidity 95% relative, non-condensing Weight 3.9 oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16 ms. Mechanical View Inches (Millimeters) THDM Low Voltage Products & Systems 5.23

24 Delay On Make (Operate) THD1 Digi-Power Power Timing Module Description The THD Series combines accurate timing circuitry with high power solid state switching. It can switch motors, lamps, and heaters directly without a contactor. You can reduce labor, component cost, and increase reliability with these small, easy-to-use, Digi-Power. High Load Currents up to 20, 200 Inrush Fixed or djustable Delays From 0.1 s m +/-0.5% Repeat ccuracy +/-1% Factory Calibration 24, 120, or 230 V C Metallized Mounting Surface for Efficient Heat Transfer Totally Solid State and Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make V = Voltage L = Load TD = R = Reset = Undefined time pprovals: Connection ccessories External adjust potentiometer P (fig ) P (fig ) Female quick connect P (WG 14/16) P (WG 10/12) Quick connect to screw adaptor P/N: P Versa-knob P/N: P See accessory pages for specifications. R T is used when external adjustment is ordered. Dashed lines are internal connections. S1 = Optional Low Current Initiate Switch Ordering Table THD1 Series Rating djustment * V C 1 - Fixed V C 2 - External C V C djust 3 - Onboard djust Example P/N: THD1223 Fixed THD1C410.1S s s s m m m *If Fixed Delay is selected, insert delay [ ] followed by (S) secs. or (M) mins. THD1Gen Low Voltage Products & Systems

25 Delay On Make (Operate) THD1 Digi-Power Power Timing Module Technical Data Range 0.1 s m in 6 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-1% Recycle Time 150 ms vs. Temperature & Voltage +/-2% Voltage 24, 120, or 230 V C Tolerance +/-20% Line Frequency Hz Power Consumption 2 V Solid state Form Normally Open, open during timing Maximum Load Current Steady State Inrush** **Must be bolted to a metal surface using 6 60 the included heat sink compound. The maximum mounting surface temperature is C C. Inrush: Non-repetitive for 16 ms. Minimum Load Current 100 m Voltage Drop 2.5 V at rated current OFF State Leakage Current 5 m at 230 V C Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting ** Surface mount with one #10 (M5 x 0.8) screw Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating/StorageTemperature -40 C C / -40 C C Humidity 95% relative, non-condensing Weight 3.9 oz (111 g) External Resistance vs Mechanical View Fixed & External djust Onboard djust THD1Gen Inches (Millimeters) Low Voltage Products & Systems 5.25

26 Delay On Make (Operate) KSD1 Digi-Timer Timing Module Description The KSD1 Series features two-terminal, series-connection with the load. The KSD1 Series is an ideal choice for delay on make timing applications. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable solid state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for popular C and DC voltages. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1 steady and 10 inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Fixed or djustable Delays from 0.1 s min in 6 Ranges +/-0.5% Repeat ccuracy +/-5% Factory Calibration V in 5 Ranges 1 Solid State pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Connection Function Delay On Make V = Voltage L = Load R = Reset TD = = Undefined time ccessories External adjust potentiometer P (fig ) P (fig ) Mounting bracket P/N: P Female quick connect P (WG 14/16) P (WG18/22) R T is used when external adjustment is ordered. Load may be connected to terminal 3 or 1. Dashed lines are internal connections. Quick connect to screw adaptor P/N: P Versa-knob P/N: P Ordering Table DIN rail adaptor P/N: P DIN rail C103PM (l) (Steel) See accessory pages for specifications. KSD1 Series Voltage djustment * 1-12 V DC 1 - Fixed s 2-24 V C 2 - External s 3-24 V DC djust s V C 3 - Onboard m V C djust m m Example P/N: KSD1421 Fixed KSD1410.5S *If Fixed Delay is selected, insert delay [ ] followed by (S) secs. or (M) mins. KSD1Gen Low Voltage Products & Systems

27 Delay On Make (Operate) KSD1 Digi-Timer Timing Module Technical Data Range 0.1 s m in 6 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-5% Recycle Time 150 ms vs. Temperature & Voltage +/-10% Voltage 24, 120, or 230 V C; 12 or 24 V DC Tolerance +/-20% Line Frequency Hz Solid state Form Normally Open, open during timing Maximum Load Current 1 steady state, 10 inrush at 60 C Minimum Holding Current 40 m OFF State Leakage Current 7 m at 230 V C Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -40 C C Storage Temperature -40 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) External Resistance vs Mechanical View Fixed & External djust Onboard djust KSD1Gen Inches (Millimeters) Low Voltage Products & Systems 5.27

28 Delay On Make (Operate) TS1 Versa-Timer Timing Module Description Versa-Timer offers proven reliability and performance with years of use in OEM equipment and commercial applications. This encapsulated general use timing module is capable of controlling load currents ranging from 5 m to 1. May be connected in series with contactors, relays, valves, solenoids, small motors, and lamps. Two Terminal Series Connection with Load 5 m... 1 Load Currents Totally Solid State +/-2% Repeat ccuracy Fixed or djustable Delays From 50 ms m in 8 Ranges pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make V = Voltage L = Load R = Reset TD = = Undefined time ccessories External adjust potentiometer P/N: P1004- (fig ) P (fig ) Connection s s s s 12 VDC VTP P/N VTP2 VTP2E VTP2F VTP2H Fig. P/N Fig. P/N P P P P P P P P Mounting bracket P/N: P Female quick connect P/N: P (WG 14/16) ll Other Voltages VTP P/N Fig. P/N Fig. P/N s VTP4 P P s VTP4F P P s VTP4J P P s VTP5N P P Plug-on adjustment module P/N: VTP()() DIN rail adaptor P/N: P Quick connect to screw adaptor P/N: P Versa-knob P/N: P DIN rail (Steel) C103PM (l) See accessory pages for specifications. Load may be connected to terminal 3 or 1. R T is used when external adjustment is ordered. Ordering Table TS1 Series djustment * ll Other 1-12 V DC 1 - Fixed 12 V DC Voltages 2-24 V C 2 - External s s 3-24 V DC djust s s V C s s V DC s s V C Example P/N: TS1122 Fixed TS *If Fixed Delay is selected, insert delay [ ] (12V DC) or [ ] (other voltages) in secs. TS Low Voltage Products & Systems

29 Delay On Make (Operate) TS1 Versa-Timer Timing Module Technical Data nalog circuitry Range 12 V DC s in 4 adjustable ranges or fixed (1 MΩ max. R T ) Other Voltages s in 4 adjustable ranges or fixed Repeat ccuracy +/-2% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-10% Recycle Time fter timing 16 ms During timing 0.1% of time delay or 75 ms, whichever is greater vs. Temperature & Voltage +/-10% Voltage 12, 24 or 120 V DC; 24, 120, or 230 V C Tolerance +/-20% Line Frequency Hz Solid state Form Normally Open, open during timing Maximum Load Current 1 steady state, 10 inrush at 60 C Minimum Holding Current 5 m Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating/Storage Temperature -40 C C / -40 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) Mechanical View Inches(Millimeters) TS Low Voltage Products & Systems 5.29

30 Delay On Make (ON-Delay) TH1 Series Power Timing Module Description The TH1 Series is a solid state relay and timer combined into one compact, easy-to-use control. This highly reliable device eliminates the need for a separate solid state relay. When mounted to a metal surface, it can switch load currents up to 20 steady state, and 200 inrush. High Current Load Capacity up to 20 with 200 Inrush Solid State Switching -- No Contact Wear or rcing Fixed or djustable Time Delays From s in +/- 2% Repeat ccuracy +/- 5% Factory Calibration Metallized Mounting Surface for Efficient Heat Transfer pprovals: Upon application of input voltage, the time delay begins. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Connection Function Delay On Make V = Voltage L = Load TD = R = Reset = Undefined time ccessories External adjust potentiometer P (fig ) P (fig ) R T is used when external adjustment is ordered. Dashed lines are internal connections. S1 is an optional low current initiate switch. Female quick connect P (WG 14/16) P (WG 10/12) Quick connect to screw adaptor P/N: P Versa-knob P/N: P See accessory pages for specifications. Ordering Table TH1 Series Rating djustment * V C 1 - Fixed s V C 2 - External s C V C djust s 3 - Onboard s djust Example P/N: TH1223 Fixed TH1C410.1 *If fixed delay is selected, insert delay [ ] in seconds. TH1Gen Low Voltage Products & Systems

31 Delay On Make (ON-Delay) TH1 Series Power Timing Module Technical Data Range s in 4 adjustable ranges or fixed Repeat ccuracy +/-2% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/- 5% vs. Temperature and Voltage +/-10% Recycle Time 150 ms Voltage 24, 120, or 230 V C Tolerance +/-15% Line Frequency Hz Power Consumption 2 V Solid state Form Normally Open, open during timing Maximum Load Currents Steady State Inrush** C Minimum Load Current 100 m Voltage Drop 2.5 V at rated current OFF State Leakage Current 5 m at 230 V C Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting ** Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.51 in. (50.8 x 50.8 x 38.4 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -20 C C Storage Temperature -40 C C Humidity 95% relative, non-condensing Weight 3.9 oz (111 g) **Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Non-repetitive for 16 ms. Mechanical View Fixed & External djust Onboard djust TH1Gen Inches (Millimeters) Low Voltage Products & Systems 5.31

32 Delay On Make (Operate) MSM PC Mount Timer Timing Module Description The MSM replaces bi-metal type timing with reliable solid state circuitry. There are no moving parts to arc or wear. It is a cost effective solution for OEM designers. It is available for printed circuit board mounting or surface mounting with a removeable bracket and wire leads. The MSM offers immediate reset on removal of power. Printed Circuit Mount or Wire Leads Fixed Delays from s +/- 5% Repeat ccuracy +/- 15% Factory Calibration Two-Wire Series Connection with the Load Fast Reset pprovals: The time delay begins upon application of input voltage. The output is de-energized before and during the time delay. t the end of the time delay, the output energizes and remains energized until input voltage is removed. Reset: Removing input voltage resets the time delay and output. Function Delay On Make V = Voltage R = Reset L = Load TD = = Undefined time Connection V = Voltage L = Load R = Red Wire = lack Wire Ordering Table MSM Series Fixed Wire 1-12 V DC s 2-24 V C 3-24 V DC Specify fixed time V C in seconds P - PC Mount V C W - Stranded Wire Leads Example P/N: MSM47P3, MSM610W8 Wire Length Inches (mm) (6.35) (9.53) (12.70) (15.88) (19.05) (152.4) (177.8) (203.2) (228.6) MSM Low Voltage Products & Systems

33 Delay On Make (Operate) MSM PC Mount Timer Timing Module Technical Data nalog Circuitry Range s fixed Repeat ccuracy +/-5% Tolerance (Factory Calibration) +/-15% Recycle Time 75 ms vs. Temperature & Voltage +/-15% Voltage 12 or 24 V DC; 24, 120, or 230 V C Tolerance +/-10% Line Frequency Hz Solid State Form Normally Open, open during timing Maximum Load Current 0.5 steady state 25 C; 0.25 steady state 60 C Minimum Holding Current 40 m Voltage Drop 2.5 V at 0.5 Protection Circuitry Dielectric reakdown 2000 V RMS input to mounting surface Insulation Resistance 100 MΩ Polarity DC units are reverse polarity protected Mechanical Mounting a. PC Mount 14 WG (2.087mm 2 ) wires (Can be inserted in MP Miniature Spring Socket # ) b. Stranded 18 WG wire leads (0.933 mm 2 ) with mounting bracket Environmental /Storage Temperature -20 C C / -30 C C Humidity 95% relative, non-condensing Weight P: 1.1 oz (31.2 g) W: 1.2 oz (34 g) Mechanical View Stranded Wire Leads See Ordering Table for wire length W = 18 WG (0.82 mm 2 ) wires = Removable mounting bracket P = 14 WG (2.087 mm 2 ) wires MSM Inches (Millimeters) PC Mount Low Voltage Products & Systems 5.33

34 Delay On Make - Normally Closed TSD4 Digi-Timer Timing Module Description The TSD4 Digi-Timer is a delay on make timer with a normally closed solid state output. The load is energized prior to and during the delay period. The TSD Series is designed for more demanding commercial and industrial applications where small size, and accurate performance is required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available. The output is rated 1 steady and 10 inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Fixed or djustable Delays From 0.1 s h 24, 120, or 230 V C +/-0.1% Repeat ccuracy +/-1% Factory Calibration 1 Solid State pprovals: Upon application of input voltage, the load energizes immediately. When the initiate switch is closed, the time delay begins. t the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load energizes again and the time delay is reset. Removing input voltage resets the time delay. Function Delay On Make NC V = Voltage S1 = Initiate Switch L = Load R = Reset TD = = Undefined time ccessories Connection External adjust potentiometer P (fig ) P (fig ) Mounting bracket P/N: P Female quick connect P/N: P (WG 14/16) Quick connect to screw adaptor P/N: P R T is used when external adjustment is ordered. Dashed lines are internal connections. S1 = Initiate Switch Versa-knob P/N: P Ordering Table DIN rail adaptor P/N: P DIN rail (Steel) C103PM (l) See accessory pages for specifications. TSD4 Series djustment * 2-24 V C 1 - Fixed s V C 2 - External s V C djust s 3 - Onboard m djust m m h Example P/N: TSD4421 Fixed TSD4410.5S *If Fixed Delay is selected, insert delay [ ] followed by (S) secs. or (M) mins., [1 100] (H) hrs TSD4Gen Low Voltage Products & Systems

35 Delay On Make - Normally Closed TSD4 Digi-Timer Timing Module Technical Data Range 0.1 s h in 7 adjustable ranges or fixed Repeat ccuracy +/-0.1% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-1% Reset Time 150 ms vs. Temperature & Voltage +/-1% Voltage 24, 120, or 230 V C Tolerance +/-20% Line Frequency Hz Power Consumption 2 V Solid state Form Normally Closed, closed before & during timing Maximum Load Current 1 steady state, 10 inrush at 60 C OFF State Leakage Current 5 m at 230 V C Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -40 C C Storage Temperature -40 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) External Resistance vs Mechanical View Fixed & External djust Onboard djust TSD4Gen Inches (Millimeters) Low Voltage Products & Systems 5.35

36 Delay On Make - Normally Closed THD4 Digi-Power Timing Module Description The THD4 utilizes solid state circuitry and a solid state relay in one easy to use control. The metallized mounting surface allows a metal panel to dissipate heat rather than adding an expensive heat sink. The solid state output is rated 6, 10, or 20 amps steady and up to 200 amps inrush. Motors, heaters and valves can be switched directly, eliminating the expense of a separate contactor. The THD4 offers substantial performance, reliability, and cost advantages for OEM designers. Load Energized Prior To and During Timing High Load Current Capacity up to 20, 200 Inrush +/-0.5% Repeat ccuracy +/-1% Factory Calibration Totally Solid State and Fixed or djustable Delays From 0.1 s m in 6 Ranges pprovals: Upon application of input voltage, the load is energized immediately. When the initiate switch closes, the time delay begins. t the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load is again energized and the time delay is reset. Removing input voltage resets the time delay and the output. Connection Function Delay On Make NC V = Voltage S1 = Initiate Switch L = Load TD = R = Reset = Undefined time ccessories External adjust potentiometer P (fig ) P (fig ) S1 = Low current initiate switch Female quick connect P (WG 14/16) P (WG 10/12) R T is used when external adjustment is ordered. Dashed lines are internal connections. Ordering Table Quick connect to screw adaptor P/N: P Versa-knob P/N: P See accessory pages for specifications. THD4 Series Rating djustment * C V C V C V C Example P/N: THD4620 Fixed THD4410.5S 1 - Fixed 2 - External djust 3 - Onboard djust s s s m m m *If Fixed Delay is selected, insert delay [ ] followed by (S) secs. or (M) mins. THD4Gen Low Voltage Products & Systems

37 Delay On Make - Normally Closed THD4 Digi-Power Timing Module Technical Data Range 0.1 s m in 6 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration) +/-1% Reset Time 150 ms vs. Temperature & Voltage +/-2% Voltage 24, 120, or 230 V C Tolerance +/-20% Line Frequency Hz Power Consumption 2 V Solid state Form Normally closed Rating Steady State Inrush* C Minimum Load Current 100 m Voltage Drop 2.5 V at rated current OFF State Leakage Current 5 m at 230 V C Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting * Surface mount with one #10 (M5 x 0.8) screw Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating/Storage Temperature -40 C C / -40 C C Humidity 95% relative, non-condensing Weight 3.9 oz (111 g) External Resistance vs *Must be bolted to a metal surface using the included heat sink compound. The maximum mounting surface temperature is 90 C. Inrush: Nonrepetitive for 16 ms. Mechanical View Fixed & External djust Onboard djust THD4Gen Inches (Millimeters) Low Voltage Products & Systems 5.37

38 Delay On Make - Normally Closed KSD4 Digi-Timer Timing Module Description The KSD4 Digi-Timer offers a delay on make function with normally closed solid state output. The load is energized prior to and during the time delay. This series is designed for general purpose commercial and industrial applications where a small, cost effective, reliable solid state timer is required. The factory calibration for fixed time delays is within 5% of the target time delay. The repeat accuracy, under stable conditions, is 0.5% of the selected time delay. This series is designed for input voltages of 24, 120 or 230 V C. Time delays of 0.1 seconds to 1000 minutes are available in 6 ranges. The output is rated 1 steady and 10 inrush. The modules are totally solid state and encapsulated to protect the electronic circuitry. Fixed or djustable Delays from 0.1 s m +/-0.5% Repeat ccuracy +/-5% Factory Calibration 24, 120, or 230 V C 1 Solid State pprovals: Upon application of input voltage, the load energizes immediately. When the initiate switch is closed, the time delay begins. t the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load energizes and the time delay is reset. Removing input voltage resets the time delay. Function Delay On Make NC V = Voltage S1 = Initiate Switch L = Load R = Reset TD = = Undefined time ccessories Connection External adjust potentiometer P (fig ) P (fig ) Mounting bracket P/N: P Female quick connect P/N: P (WG 14/16) Quick connect to screw adaptor P/N: P R T is used when external adjustment is ordered. Dashed lines are internal connections. S1 = Initiate Switch DIN rail adaptor P/N: P Versa-knob P/N: P DIN rail (Steel) C103PM (l) See accessory pages for specifications. Ordering Table KSD4 Series djustment * 2-24 V C 1 - Fixed s V C 2 - External s V C djust s 3 - Onboard m djust m m Example P/N: KSD4421 Fixed KSD4410.5S *If Fixed Delay is selected, insert delay [ ] followed by (S) secs. or (M) mins. KSD4Gen Low Voltage Products & Systems

39 Delay On Make - Normally Closed KSD4 Digi-Timer Timing Module Technical Data Range 0.1 s m in 6 adjustable ranges or fixed Repeat ccuracy +/-0.5% or 20 ms, whichever is greater Tolerance (Factory Calibration +/- 5% Reset Time 150 ms vs. Temperature & Voltage +/-10% Voltage 24, 120, or 230 V C Tolerance +/-20% Line Frequency Hz Power Consumption 2 V Solid state Form Normally Closed, closed before and during timing Maximum Load Current 1 steady state, 10 inrush at 60 C OFF State Leakage Current 5 m at 230 V C Voltage Drop 2.5 V at 1 Protection Circuitry Dielectric reakdown 2000 V RMS terminals to mounting surface Insulation Resistance 100 MΩ Mechanical Mounting Surface mount with one #10 (M5 x 0.8) screw Package 2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm) Termination 0.25 in. (6.35 mm) male quick connect terminals Environmental Operating Temperature -40 C C Storage Temperature -40 C C Humidity 95% relative, non-condensing Weight 2.4 oz (68 g) External Resistance vs Mechanical View Fixed & External djust Onboard djust KSD4Gen Inches (Millimeters) Low Voltage Products & Systems 5.39

40 Delay On Make - Normally Closed TS4 Series Versa Timing Module Description The TS4 Versa-Timer is an analog delay on make timer with a normally closed solid state output. Unlike an Interval Timer, the load is energized prior to and during the time delay period. It can be used as a faster starting Interval time delay when S1 is closed upon application of input voltage. Load Energized Prior To and During Fixed or djustable Delays s in 4 Ranges +/-2% Repeat ccuracy 24, 120, or 230 V C 1 Solid State pprovals: Upon application of input voltage, the load is energized immediately. When the initiate switch is closed, the time delay begins. t the end of the time delay, the load de-energizes. Reset: When the initiate switch is reopened, the load again energizes and the time delay is reset. Removing input voltage resets the time delay and output. Function Delay On Make NC V = Voltage R = Reset L = Load TD = S1 = Initiate Switch = Undefined time ccessories External adjust potentiometer P1004- (fig ) P (fig ) (See RT Table) Mounting bracket P/N: P Female quick connect P/N: P (WG 14/16) Connection R T Selection Table VTP P/N Fig. P/N Fig. P/N s s s s VTP4 VTP4F VTP4J VTP5N P P P P P P P P Quick connect to screw adaptor P/N: P S1 = Initiate Switch Plug-on adjustment module P/N: VTP()() (See RT Table) Versa-knob P/N: P DIN rail (Steel) C103PM (l) R T is used when external adjustment is ordered. Dashed lines are internal connections. Ordering Table TS4 Series djustment * 2-24 V C 1 - Fixed s V C 2 - External s V C djust s s DIN rail adaptor P/N: P See accessory pages for specifications. Example P/N: TS4624 Fixed TS *If Fixed Delay is selected, insert delay [ ] in seconds. TS Low Voltage Products & Systems