NV6000 and NV8000 Series Universal Routers User Guide

Transcription

1 Series Universal Routing Switch Series Universal Routing Switch Series Universal Routing Switch NV6000 and NV8000 Series Universal Routers User Guide ENVOY6128 ENVOY6256 Series Universal Routing Switch ENVOY6064 Power Supply Frame ENVOY8256 ENVOY6257 POWER SUPPLY November 2002 UG

2 FRONT MATTER COPYRIGHT AND TRADEMARKS Copyright 2001, NVISION, Inc. All rights reserved. Printed in USA. NVISION is a registered trademark of NVISION, Inc. REVISION HISTORY REVISION DATE REASON FOR CHANGE Revision A December 2001 Initial Release, incl NV8000 Series Revision -00 November 2002 Convert to User Guide format, minor corrections DISCLAIMER OF LIABILITY Contents of this publication are current as of the publication date. NVISION reserves the right to change the contents without prior notice. In no event shall NVISION be liable for any damages resulting from loss of data, loss of use, or loss of profits and NVISION further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of liability applies to all products, publications, and services during and after the warranty period. NVISION 125 Crown Point Court Grass Valley, CA 95945, USA In USA and Canada: Outside USA and Canada: FAX: or nvsales@nvision1.com Page ii

3 ABOUT THIS MANUAL This manual provides overview, installation, operation, and maintenance information about the product. Sections included are the following: Section 1: System Descriptions - Unpacking, overview, and specifications. Section 2: Installation - Physical installation, cabling, and power on. Sections 3: Theory of Operation - Block diagrams and description of the system. Section 4: Maintenance - Maintenance, troubleshooting, repair, and replacement. QUICK START If you are setting up the product for the first time and wish to do so as quickly as possible, do the following: 1. See Section 2: Installation to install the equipment. 2. See Section 3: Operation to learn how to operate the product. Page iii

4 IMPORTANT SAFEGUARDS AND NOTICES The following pages provide important safety guidelines for operators and service personnel. Specific warnings and cautions appear throughout the manual where they apply. Please read and follow this important information, especially those instructions related to the risk of electric shock or injury to persons. Warning: Any instructions in this manual that require opening the equipment cover or enclosure are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any service other than that contained in the operating instructions unless you are qualified to do so. Symbols and Their Meanings The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of dangerous voltages within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle alerts the user to the presence of important operating and maintenance/service instructions. The Ground symbol represents a protective grounding terminal. Such a terminal must be connected to earth ground prior to making any other connections to the equipment. The fuse symbol indicates that the fuse referenced in the text must be replaced with one having the ratings indicated. The presence of this symbol in or on NVISION equipment means that it has been designed, tested and certified as complying with applicable Underwriter's Laboratory (USA) regulations and recommendations. The presence of this symbol in or on NVISION equipment means that it has been designed, tested and certified as essentially complying with all applicable European Union (CE) regulations and recommendations. Page iv

5 General Warnings A warning indicates a possible hazard to personnel which may cause injury or death. Observe the following general warnings when using or working on this equipment. Heed all warnings on the unit and in the operating instructions. Do not use this equipment in or near water. This equipment is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired receptacle before connecting the equipment inputs or outputs. Route power cords and other cables so they are not likely to be damaged. Disconnect power before cleaning the equipment. Do not use liquid or aerosol cleaners; use only a damp cloth. Dangerous voltages may exist at several points in this equipment. To avoid injury, do not touch exposed connections and components while power is on. Do not wear rings or wristwatches when troubleshooting high current circuits such as the power supplies. To avoid fire hazard, use only the specified fuse(s) with the correct type number, voltage and current ratings as referenced in the appropriate locations in the service instructions or on the equipment. Always refer fuse replacements to qualified service personnel. To avoid explosion, do not operate this equipment in an explosive atmosphere. Have qualified service personnel perform safety checks after any service. General Cautions A caution indicates a possible hazard to equipment that could result in equipment damage. Observe the following cautions when operating or working on this equipment. When installing this equipment, do not attach the power cord to building surfaces. To prevent damage to equipment when replacing fuses, locate and correct the problem that caused the fuse to blow before re-applying power. Use only the specified replacement parts. Follow static precautions at all times when handling this equipment. This product should only be powered as described in the manual. To prevent equipment damage, select the proper line voltage on the power supply(ies) as described in the installation documentation. To prevent damage to the equipment, read the instructions in the equipment manual for proper input voltage range selection. Page v

6 POWER CORD WIRING The power cord differs depending on your location. See the information below. Also note that the power cords supplied with this equipment provide the only means of mains disconnection. The socket-outlet must be installed near the equipment and must be easily accessible. NORTH AMERICAN POWER SUPPLY CORDS The North American power cords supplied with this equipment have a molded grounding plug (NEMA 5-15P) at one end and molded grounding receptacle (IEC 320-C13) at the other end (see figure below). Conductors are CEE color-coded: Light blue (neutral), Brown (line) and Green or Green/Yellow (ground). Operation of this equipment at voltages exceeding 130 VAC will require power supply cords which comply with NEMA configurations. Brown Blue Line Neutral Green or Green with Yellow Stripe Ground (Earth) INTERNATIONAL POWER SUPPLY CORDS The International power cords supplied with this equipment have a molded grounding receptacle (IEC 320- C13) at one end and stripped conductors (50/5 mm) at the other end (see figure below). Conductors are CEE color-coded: Light blue (neutral), Brown (line) and Green/Yellow (ground). Other IEC 320-C13 type power supply cords can be used if they comply with the safety regulations of the country in which they are installed. Brown Blue Green with Yellow Stripe Line Neutral Ground (Earth) FCC (USA) COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Page vi

7 This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference in which case the user will be required to correct the interference at their own expense. FCC Emission Limits This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesirable operation. EUROPEAN COMMUNITY (CE) DECLARATION OF CONFORMANCE All of the equipment described in this manual has been designed to conform with the required safety and emissions standards of the European Community. Products tested and verified to meet these standards are marked as required by law with the CE mark (See Symbols and Their Meanings above.) When shipped into member countries of the European Community, this equipment is accompanied by authentic copies of original Declarations of Conformance on file in NVISION offices in Grass Valley, California USA. Page vii

8 TECHNICAL SUPPORT NVISION has made every effort to ensure that the equipment you receive is in perfect working order. In the event that problems arise which you cannot resolve, or if there are any questions regarding this equipment or information about other products manufactured by NVISION, please contact your local representative or contact NVISION directly through one of the appropriate means listed below: Telephone:* Main Number * Technical Support Sales / Facsimile: Main Number Sales Web Site: Mail: Shipping:* Technical Support - nvsupport@nvision1.com Sales - nvsales@nvision1.com NVISION P.O. Box 1658 Nevada City, CA 95959, USA NVISION 125 Crown Point Court Grass Valley, CA 95945, USA * Material Return Authorization required before any equipment is returned. Page viii

9 TABLE OF CONTENTS Content Page FRONT MATTER COPYRIGHT AND TRADEMARKS ii REVISION HISTORY ii DISCLAIMER OF LIABILITY ii ABOUT THIS MANUAL iii QUICK START iii IMPORTANT SAFEGUARDS AND NOTICES iv Symbols and Their Meanings iv General Warnings v General Cautions v POWER CORD WIRING vi NORTH AMERICAN POWER SUPPLY CORDS vi INTERNATIONAL POWER SUPPLY CORDS vi FCC (USA) COMPLIANCE STATEMENT vii FCC Emission Limits vii EUROPEAN COMMUNITY (CE) DECLARATION OF CONFORMANCE vii TECHNICAL SUPPORT viii SECTION 1: SYSTEM DESCRIPTIONS INTRODUCTION NV6064 SYSTEM DESCRIPTION NV6064 Front Panel NV6064 Rear Panel NV6064 Specifications NV6128 SYSTEM DESCRIPTION NV6128 Front Panel NV6128 Specifications NV6256 SYSTEM DESCRIPTION NV6256 Electronics Frame Front Panel NV6256 Electronics Frame Rear Panel NV6256 Specifications NV8256 SYSTEM DESCRIPTION NV8256 Electronics Frame Front Panel Page ix

10 Content Page NV8256 Electronics Frame Rear Panel NV8256 Specifications NV6257 POWER SUPPLY FRAME FOR 6256/ CONTROL CONNECTORS (ALL MODELS) DIAGNOSTIC CONNECTORS (ALL MODELS) RS-232 DIAG Port Cable Pin-out RS-422 DIAG Port Cable Pin-out ALARMS CONNECTOR (ALL MODELS) Alarm Definitions POWER SUPPLY ALARMS CONNECTOR (6064/6128) POWER SUPPLY ALARMS CONNECTOR (6256/8256) SECTION 2: INSTALLATION RECEIVING INSPECTION AND UNPACKING PREPARING FOR INSTALLATION POWER SUPPLY SAFETY FOR ALL MODELS INSTALLING THE ROUTER Installing the NV Installing the NV Installing the NV Installing the NV VERIFICATION AND CONFIGURATION (ALL MODELS) Verification Configuration REDUNDANT CROSSPOINT OPERATION Replacing a Primary Crosspoint Remote Control Connections SECTION 3: THEORY OF OPERATION ENVOY ROUTERS SYSTEM THEORY OF OPERATION Page x

11 Content Page SECTION 4: MAINTENANCE MAINTENANCE Washing Air Filters LED Indicators Fan Servicing NV6064 Fans NV6128 and 6256 Fans NV8256 Fans Fuse Replacement TROUBLESHOOTING Power Supplies Power Supply Checks Controller Checks Signal Path Checks ORDERING REPLACEMENT ASSEMBLIES Page xi

12 Page xii UG November 2002

13 Section 1: System Descriptions This manual describes the NV6064, NV6128, NV6256, and NV8256 routers. Other routers in the ENVOY series, such as the NV6904 and the NV7256, are described in separate manuals. This section covers the following topics: Contents Page INTRODUCTION NV6064 SYSTEM DESCRIPTION NV6064 Front Panel NV6064 Rear Panel NV6064 Specifications NV6128 SYSTEM DESCRIPTION NV6128 Front Panel NV6128 Specifications NV6256 SYSTEM DESCRIPTION NV6256 Electronics Frame Front Panel NV6256 Electronics Frame Rear Panel NV6256 Specifications NV8256 SYSTEM DESCRIPTION NV8256 Electronics Frame Front Panel NV8256 Electronics Frame Rear Panel NV8256 Specifications CONTROL CONNECTORS (ALL MODELS) DIAGNOSTIC CONNECTORS (ALL MODELS) ALARMS CONNECTOR (ALL MODELS) POWER SUPPLY ALARMS CONNECTOR (6064/6128) POWER SUPPLY ALARMS CONNECTOR (6256/8256) Page 1-1

14 INTRODUCTION NVISION manufactures the 6000 and 8000 Series ENVOY Universal Digital Routers. Each router, identified below, combines compact frame size (with optional redundant power supplies) and the capability of managing a wide range of signal formats. NV6064 provides up to 64 x 64 Inputs and Outputs with dual outputs. NV6128 provides up to 128 x 128 Inputs and Outputs with dual outputs. NV6256 provides up to 256 Inputs and 128 Outputs with dual outputs. NV8256 provides up to 256 x 256 Inputs and Outputs with single outputs. Designed around a novel high speed crosspoint architecture, each router can handle data rates from 3 Megabits per second to more than 1.5 Gigabits per second. We call this capability Super Wideband (SWB). The crosspoint structure is combined with SDI or SWB input/output modules to accommodate SDI and/or SWB data rates within the same frame, at the same time. With unique equalizers, reclockers, and cable drivers, the router passes pathological signals at both SDI and HD-SDI data rates. No signal inversion of the primary outputs takes place, which is essential for systems handling DVB-ASI data streams since DVB- ASI is 8B/10B coded and cannot be inverted. Secondary outputs are inverted. Input and output modules are available for SDI (143, 177, 270, and 360 Mbits) and Super Wideband (3 Mbits/sec to 1.5 Gbits) data rates. Dual output connectors for each destination minimize DA requirements on 6000 Series routers. Expandable in increments of 8 Inputs or Outputs (and 16 Inputs or Outputs on the 8256), combined with the ability to control a router from an existing control system, the router provides the user with tremendous flexibility. The modules load through the front and can be hot swapped (no need to power down the frame). Figure 1-1 shows simplified block diagrams of the 6000 and 8000 Series ENVOY routers. Page 1-2

15 SDI Input Card 143, 177, 270, 360 Mb/s x8 SWB Input Card 3 Mb/s to 1.5 Gb/s x8 Clock Generator High Speed Crosspoint Matrix SDI Output Card 143, 177, 270, 360 Mb/s x8 SWB Output Card 3 Mb/s to 1.5 Gb/s x8 Control System Interface and CPU ENVOY 6000 Series SDI Input Card 143, 177, 270, 360 Mb/s x16 SWB Input Card 3 Mb/s to 1.5 Gb/s x16 Clock Generator High Speed Crosspoint Matrix SDI Output Card 143, 177, 270, 360 Mb/s x16 SWB Output Card 3 Mb/s to 1.5 Gb/s x16 Control System Interface and CPU ENVOY 8000 Series Figure 1-1. ENVOY Systems Simplified Block Diagram Page 1-3

16 NV6064 SYSTEM DESCRIPTION The NV6064 Universal Digital Router system is housed in a single frame, including electronics and power supplies. The frame is 12 RUs high and designed to be installed in a standard 19 equipment rack. In addition to those discussed on the previous pages, features of the NV6064 include: Dual output connectors to reduce DA requirements. Optional redundant power supply. Optional secondary control available for some host controllers. Front and rear panels are described starting below; NV6064 specifications follow the rear panel description. NV6064 Front Panel Figure 1-2 illustrates the NV6064 front panel (door open). The front panel provides access to the following assemblies: Cooling fans, pull air into the frame through the front door and exhaust air out through the rear. Up to 8 Output modules (can be a combination of SDI and SWB) 8 outputs per board. Output Monitor module (optional). Controller, Primary and Secondary (optional). Module is not slot dependent. Up to 8 Input modules (can be a combination of SDI and SWB), 8 inputs per board. Main Crosspoint module slot, 64 inputs x 64 outputs. Unused slot. Main Power Supply. Redundant Power Supply (optional). Page 1-4

17 FAN OUTPUTS 1-8 OUTPUTS 9-16 INPUTS 1-8 INPUTS 9-16 INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUT MONITOR CONTROLLER - SECONDARY CONTROLLER - PRIMARY 64 x 64 CROSSPOINT MAIN 6 UNUSED SLOT 7 MAIN POWER SUPPLY REDUNDANT POWER SUPPLY 8 9 Figure 1-2. NV6064 Front Panel Page 1-5

18 NV6064 Rear Panel Figure 1-3 illustrates the NV6064 rear panel. The rear panel contains the following connectors: 64 Dual Output (A - non-inverted, and B - inverted) Matrix BNC connectors (128 total). 64 Input Matrix BNC connectors. IEC Standard AC power connector for Main Power Supply (PS1) and Redundant Power Supply (PS2). Power Supply Alarms connector. For connection details, see the heading, "Power Supply Alarms Connector (6064/6128)" on page System Alarms connector. For connection details, see the heading, "Alarms Connector (all models)" on page Monitor outputs (optional). Outputs 1 and 2 are identical SWB signals. Outputs 3 and 4 are identical SD signals. Video Reference 1 and 2. Connect analog PAL or NTSC composite video. Ethernet and SMS7000 GSC Node Bus control system connectors. Ethernet connectors may be used for the NVISION NV9000 Series Control System, and the GSC Node Bus connectors are used for the GVG SMS7000 Control System. See the documentation for those systems for connection details. Serial Control and Diagnostic connectors. Connect your main control system to the Primary and Secondary CTRL 1 connectors. This provides control connections to the primary and secondary Controller modules. If you have a second alternate control system, use the Primary and Secondary CTRL 2 connectors. Use the DIAG connectors for connecting to a PC to run the supplied UniConfig router configuration software. See Figure 1-11 on page 1-29 for Control connector drawings and pin-outs, which are the same for all four control connectors. See the UniConfig manual for the diagnostic port pin outs. Note: Connectors not described here are reserved for future use. Page 1-6

19 FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN 9 { PRIMARY CTRL 1 CTRL 2 SECONDARY CTRL 1 CTRL 2 1 DIAG DIAG 8 AES REF 1 COMMON TO PRI & SEC AES REF BASE 2 10 BASE 2 10/100 BASE T 10/100 BASE T GSC COMMON TO PRI & SEC NODE BUS LOOP THRU COMMON TO PRI & SEC 7 VIDEO REF 1 VIDEO REF 2 1 LOOP THRU (2) 2 6 M ON I T O R 3 5 COMMON TO PRI & SEC ALARMS TIMECODE 4 OUTPUTS INPUTS PS 1 LEFT 3 NVISION, INC. ENVOY / V~ 7.0A/3.75A 50/60Hz 660 WATTS MAX T 8.0A 250V FOR V~ T 6.3A 250V FOR V~ FUSES LOCATED ON POWER SUPPLIES CAUTION THIS EQUIPMENT HAS MORE THAN ONE POWER SUPPLY CORD. TO REDUCE THE RISK OF ELECTRIC SHOCK DISCONNECT 2 POWER SUPPLY CORDS BEFORE SERVICING. CONTROL NO. 9K50 PROFESSIONAL VIDEO/AUDIO Æ LISTED CAUTION PLEASE READ INSTRUCTION MANUAL BEFORE CONNECTING EQUIPMENT TO THE MAINS PS 2 RIGHT "THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATIONS." PS ALARMS 1 AND 2 NORMALLY CLOSED 1 C 2 O M 4 Figure 1-3. NV6064 Rear Panel Page 1-7

20 NV6064 Specifications TYPE Electrical AC Power Fuses Connectors Power Consumption Regulatory Mechanical Module Slots Power Supply Slots Table 1-1 lists the specifications for the NV6064 Router. Table 1-1. NV6064 SPECIFICATIONS PARAMETER / VAC, 50/60Hz, Auto-ranging Crosspoint Module - 7A, 125V (F) F1 Fast & 1A, Auto Reset. I/O Modules - 1A, Auto Reset. Controller Module - 3A, 125V (F) F1 Fast. Power Supplies - 8.0A, V; 6.3A, V. 2, IEC Filtered AC 660 Watts (maximum) UL Listed and CE Compliant 8 Input modules, 8 channels each. 8 Output modules, 8 channels each. 1 64x64 Crosspoint module. 2 Controller modules (1 Primary, 1 Optional Secondary). 1 Output Monitor module (Optional). 1 (1 Main, 1 Optional Redundant) Dimensions EIA Standard (12 RU High) 21.0 (533.4mm) H x 19.0 (482.6mm) W x 19.0 (482.6mm) D. Weight (fully loaded) 91.0 lbs (41.4 kg), max. Inputs/Outputs Input/Output specifications follow SMPTE standards for SDI (259M) and HD-SDI (292M) signals, where applicable. Cable Equalization Automatic, designed for Belden (HD) or Belden 8281 at 270Mb/s (SD) Video Ref Input Type Analog PAL and/or NTSC Color Black Connectors 4 BNC (2 pairs), Loop-thru Return Loss >30dB to 5MHz Performance Reclocking Yes Input to Output Delay <10ns Crosspoint Granularity 64x64 GSC Node Bus For Tektronix SMS7000 Control System External Communications Port Type RS-422 Serial Ports, usage determined by software Connectors 6, 9-pin, D-type (2 Primary, 2 Secondary, 2 Diagnostic) External Alarm Port 1 D-type, 9-pin connector Environmental Operating Temperature 0 to 40 degrees Centigrade, Ambient Relative Humidity 0 to 90%, non-condensing Page 1-8

21 NV6128 SYSTEM DESCRIPTION The NV6128 Universal Digital Router system is housed in a single frame, including electronics and power supplies. The frame is 18 RUs high and is designed to be installed in a standard 19 equipment rack. In addition to those discussed on the previous pages, features of the NV6128 include: Dual output connectors to reduce DA requirements. Optional redundant power supplies. Optional secondary control. Front and rear panels are described starting below; NV6128 specifications follow the rear panel description. Page 1-9

22 NV6128 Front Panel Figure 1-4 illustrates the NV6128 front panel (door open). The front panel provides access to the following assemblies: Up to 16 Output Cards (can be a combination of SDI and SWB), 8 outputs per card. Output Monitor (optional). Controller, Primary and Secondary (optional). Module is not slot dependent. Cooling fans, pull air into the frame through the front door across the Crosspoint modules and exhaust air out through the rear. Up to 4 Crosspoint modules, 128 inputs x 32 outputs per module. Up to 16 Input Cards (can be a combination of SDI and SWB), 8 inputs per board. Main Power Supplies 1 and 2. Note: Two (2) Power Supplies are required for normal operation. Redundant Power Supplies 1 and 2 (optional). Page 1-10

23 3 OUTPUTS 1-8 OUTPUTS 9-16 OUTPUTS OUTPUTS OUTPUTS OUTPUTS X32 CROSSPOINT OUTPUTS 1-32 FAN 128X32 CROSSPOINT OUTPUTS X32 CROSSPOINT OUTPUTS X32 CROSSPOINT OUTPUTS INPUTS 1-8 INPUTS 9-16 INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUT MONITOR - OPTIONAL CONTROLLER - SECONDARY - OPTIONAL CONTROLLER - PRIMARY FAN MAIN POWER SUPPLY 1 MAIN POWER SUPPLY 2 REDUNDANT POWER SUPPLY 1 8 REDUNDANT POWER SUPPLY 2 8 MT Figure 1-4. NV6128 Front Page 1-11

24 NV6128 Rear Panel Figure 1-5 illustrates the NV6128 rear panel. The rear panel contains the following connectors: 128 Dual Output (A - non-inverted, and B - inverted) Matrix BNC connectors (256 total). 128 Input Matrix BNC connectors. IEC Standard AC power connectors for Main Power Supply 1 and 2 and Redundant Power Supply 1 and 2. Power Supply Alarm Connectors. For connection details, see the heading, "Power Supply Alarms Connector (6064/6128)" on page System Alarms connector. For connection details, see the heading, "Alarms Connector (all models)" on page Monitor outputs (optional). Outputs 1 and 2 are identical SWB signals. Outputs 3 and 4 are identical SD signals. Video Reference 1 and 2. Connect analog PAL or NTSC composite video. Ethernet and SMS7000 GSC Node Bus control system connectors. Ethernet connectors may be used for the NVISION NV9000 Series Control System and the GSC connector may be used for the GVG SMS7000 Control System. See the documentation for those systems for connection details. Serial Control and Diagnostic connectors. Connect your main control system to the Primary and Secondary CTRL 1 connectors. This provides control connections to the primary and secondary Controller modules. If you have a second alternate control system, use the Primary and Secondary CTRL 2 connectors. Use the DIAG connectors for connecting to a PC to run the supplied UniConfig router configuration software. See Figure 1-11 on page 1-29 for Control connector drawings and pin-outs, which are the same for all four control connectors. See the UniConfig manual for the diagnostic port pin outs. Note: Connectors not described here are reserved for future use. Page 1-12

25 9 { PRIMARY CTRL 1 CTRL 2 SECONDARY CTRL 1 CTRL A 121 B 122 A 113 A 113 B 114 A 105 A 105 B 106 A 97 A 97 B 98 A 89 A 89 B 90 A 81 A 81 B 82 A 73 A 73 B 74 A 65 A 65 B 66 A 57 A 57 B 58 A 49 A 49 B 50 A 41 A 41 B 42 A 33 A 33 B 34 A 25 A 25 B 26 A 17 A 17 B 18 A 9 A 9 B 10 A 1 A 1 B 2 A DIAG DIAG 122 B 114 B 106 B 98 B 90 B 82 B 74 B 66 B 58 B 50 B 42 B 34 B 26 B 18 B 10 B 2 B AES REF 1 COMMON TO PRI & SEC AES REF A 115 A 107 A 99 A 91 A 83 A 75 A 67 A 59 A 51 A 43 A 35 A 27 A 19 A 11 A 3 A 123 B 115 B 107 B 99 B 91 B 83 B 75 B 67 B 59 B 51 B 43 B 35 B 27 B 19 B 11 B 3 B 8 10 BASE 2 10 BASE 2 10/100 BASE T 10/100 BASE T 124 A 124 B 116 A 116 B 108 A 108 B 100 A 100 B 92 A 92 B 84 A 84 B 76 A 76 B 68 A 68 B 60 A 60 B 52 A 52 B 44 A 44 B 36 A 36 B 28 A 28 B 20 A 20 B 12 A 12 B 4 A 4 B A 117 A 109 A 101 A 93 A 85 A 77 A 69 A 61 A 53 A 45 A 37 A 29 A 21 A 13 A 5 A 7 GSC COMMON TO LOOP PRI & SEC NODE THRU BUS COMMON TO PRI & SEC VIDEO VIDEO REF 1 REF B 126 A 126 B 117 B 118 A 118 B 109 B 110 A 110 B 101 B 102 A 102 B 93 B 94 A 94 B 85 B 86 A 86 B 77 B 78 A 78 B 69 B 70 A 70 B 61 B 62 A 62 B 53 B 54 A 54 B 45 B 46 A 46 B 37 B 38 A 38 B 29 B 30 A 30 B 21 B 22 A 22 B 13 B 14 A 14 B 5 B 6 A 6 B A 119 A 111 A 103 A 95 A 87 A 79 A 71 A 63 A 55 A 47 A 39 A 31 A 23 A 15 A 7 A LOOP THRU (2) MONITOR B 119 B 111 B 103 B 95 B 87 B 79 B 71 B 63 B 55 B 47 B 39 B 31 B 23 B 15 B 7 B A 120 A 112 A 104 A 96 A 88 A 80 A 72 A 64 A 56 A 48 A 40 A 32 A 24 A 16 A 8 A 5 ALARMS COMMON TO PRI & SEC TIMECODE B 120 B 112 B 104 B 96 B 88 B 80 B 72 B 64 B OUTPUTS 56 B 48 B 40 B 32 B 24 B 16 B 8 B AIR EXHAUST KEEP CLEAR 6" MIN AIR EXHAUST KEEP CLEAR 6" MIN FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN I/O Cooling Fan #1 I/O Cooling Fan #2 2 INPUTS CAUTION PLEASE READ INSTRUCTION MANUAL BEFORE CONNECTING EQUIPMENT TO THE MAINS CAUTION 1 PLEASE READ INSTRUCTION MANUAL BEFORE CONNECTING EQUIPMENT TO THE MAINS PS 3 TOP RIGHT PS 1 TOP LEFT PS 4 BOTTOM RIGHT PS 2 BOTTOM LEFT PS ALARMS 3 AND COM NORMALLY CLOSED NVISION, INC. ENVOY / V~ 15.0A/7.5A 50/60Hz 1320 WATTS MAX T 8.0A 250V FOR V~ T 6.3A 250V FOR V~ FUSES LOCATED ON POWER SUPPLIES CAUTION THIS EQUIPMENT HAS MORE THAN ONE POWER SUPPLY CORD. TO REDUCE THE RISK OF ELECTRIC SHOCK DISCONNECT 4 POWER SUPPLY CORDS BEFORE SERVICING. CONTROL NO. 9K50 PROFESSIONAL VIDEO/AUDIO Æ LISTED PS ALARMS 1 AND COM NORMALLY CLOSED 4 "THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATIONS." Figure 1-5. NV6128 Rear Page 1-13

26 NV6128 Specifications TYPE Electrical AC Power Fuses Connectors Power Consumption Regulatory Mechanical Module Slots Power Supply Slots Table 1-2 lists the specifications for the NV6128 Router. Table 1-2. NV6128 SPECIFICATIONS PARAMETER / VAC, 50/60Hz, Auto-ranging Crosspoint Module - 7A, 125V (F) F1 Fast & 1A, Auto Reset. I/O Modules - 1A, Auto Reset. Controller Module - 3A, 125V (F) F1 Fast. Power Supplies - 8.0A, V; 6.3A, V. 4, IEC Filtered AC 1320 Watts (maximum) UL Listed and CE Compliant 16 Input modules, 8 channels each. 16 Output modules, 8 channels each x32 Crosspoint modules. 2 Controller modules (1 Primary, 1 Optional Secondary). 1 Output Monitor module (Optional). 4 (2 Main, 2 Optional Redundant) Dimensions EIA Standard (18 RU High) 31.5 (800.1mm) H x 19.0 (482.6mm) W x 19.0 (482.6mm) D. Weight (fully loaded) 210 lbs (95.5kg), max. Inputs/Outputs Input/Output specifications follow SMPTE standards for SDI (259M) and HD-SDI (292M) signals, where applicable. Cable Equalization Automatic, designed for Belden (HD) or Belden 8281 at 270Mb/s (SD) Video Ref Input Type Analog PAL and/or NTSC Color Black Connectors 4 BNC (2 pairs), Loop-thru Return Loss >30dB to 5MHz Performance Reclocking Yes Input to Output Delay <10ns Crosspoint Granularity 128x32 GSC Node Bus For Tektronix SMS7000 Control System External Communications Port Type RS-422 Serial Ports, usage determined by software Connectors 6, 9-pin, D-type (2 Primary, 2 Secondary, 2 Diagnostic) External Alarm Port 1 D-type, 9-pin connector Environmental Operating Temperature 0 to 40 degrees Centigrade, Ambient Relative Humidity 0 to 90%, non-condensing Page 1-14

27 NV6256 SYSTEM DESCRIPTION The NV6256 Universal Digital Router system consists of two frames. One frame houses the electronics and the other contains the (6257) power supplies. The electronics frame is 24 RUs high and the Power Supply frame is 5 RUs high. Both frames are designed to be installed in a standard 19 equipment rack. In addition to those discussed on the previous pages, features of the NV6256 include: Dual output connectors to reduce DA requirements. Optional redundant power supplies. Optional secondary control. Front and rear panels for the 6256 electronics frame are described below, followed by specifications for the NV6256. Description and specifications for the 6257 power supply frame follow the NV8256 section, which follows this section. Page 1-15

28 NV6256 Electronics Frame Front Panel Figure 1-6 illustrates the NV6256 Electronics frame front panel (door open). The front panel provides access to the following assemblies: Up to 16 Output boards (can be a combination of SDI and SWB), 8 outputs per board. Output Monitor (optional). Controller, Primary and Secondary (optional). Board is not slot dependent. Cooling fans, pull air into the frame through the front door across the Crosspoint modules and exhausts air out through the rear. Up to 8 Crosspoint boards, 128 inputs x 32 outputs per board. Up to 32 Input boards (can be a combination of SDI and SWB), 8 inputs per board. Page 1-16

29 1 2 OUTPUTS 1-8 OUTPUTS 9-16 OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUT MONITOR CONTROLLER - SECONDARY B 3 CONTROLLER - PRIMARY X32 CROSSPOINT OUTPUTS 1-32 FAN 128X32 CROSSPOINT OUTPUTS X32 CROSSPOINT OUTPUTS FAN 128X32 CROSSPOINT OUTPUTS INPUTS 1-8 INPUTS 9-16 INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS X32 CROSSPOINT OUTPUTS 1-32 FAN 128X32 CROSSPOINT OUTPUTS X32 CROSSPOINT OUTPUTS FAN 128X32 CROSSPOINT OUTPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS Figure 1-6. NV6256 Electronics Frame Front Page 1-17

30 NV6256 Electronics Frame Rear Panel Figure 1-7 illustrates the NV6256 Electronics frame rear panel. The rear panel provides access to the following connectors: 128 Dual Output (A - non-inverted, and B - inverted) Matrix BNC connectors (256 total). Power input connectors. Connect to 6257 Power Supply frame using supplied power input cables. Power supply monitor connector. Connect to 6257 Power Supply frame using supplied monitor cables. Two banks of 128 Input Matrix BNC connectors, 256 total. System Alarms connector. For connection details, see the heading, "Alarms Connector (all models)" on page Monitor outputs (optional). Outputs 1 and 2 are identical SWB signals. Outputs 3 and 4 are identical SD signals. Video Reference Inputs 1 and 2. Connect analog PAL or NTSC composite video to these inputs. Looping connectors provided. Ethernet and SMS7000 GSC Node Bus connectors. Ethernet connectors are for use with NVISION NV9000 Series Control Systems, and GSC connectors are for use with GVG SMS7000 Control Systems. See the documentation for those systems for connection details. Serial Control and Diagnostic connectors. Connect your main control system to the Primary and Secondary CTRL 1 connectors. This provides control connections to the primary and secondary Controller modules. If you have a second alternate control system, use the Primary and Secondary CTRL 2 connectors. Use the DIAG connectors for connecting to a PC to run the supplied UniConfig router configuration software. See Figure 1-11 on page 1-29 for Control connector drawings and pin-outs, which are the same for all four control connectors. See the UniConfig manual for the diagnostic port pin outs. Note: Connectors not described here are reserved for future use. Page 1-18

31 COMMON TO PRI & SEC COMMON TO PRI & SEC COMMON TO PRI & SEC COMMON TO PRI & SEC LISTED CONTROL NO. 9K50 PROFESSIONAL VIDEO/AUDIO UG November { PRIMARY CTRL 1 CTRL 2 DIAG SECONDARY CTRL 1 CTRL 2 DIAG 121 A 121 B 122 A 122 B 113 A 113 B 114 A 114 B 105 A 105 B 106 A 106 B 97 A 97 B 98 A 98 B 89 A 89 B 90 A 90 B 81 A 81 B 82 A 82 B 73 A 73 B 74 A 74 B 65 A 65 B 66 A 66 B 57 A 57 B 58 A 58 B 49 A 49 B 50 A 50 B 41 A 41 B 42 A 42 B 33 A 33 B 34 A 34 B 25 A 25 B 26 A 26 B 17 A 17 B 18 A 18 B 9 A 9 B 10 A 10 B 1 A 1 B 2 A 2 B AES REF 1 AES REF A 115 A 107 A 99 A 91 A 83 A 75 A 67 A 59 A 51 A 43 A 35 A 27 A 19 A 11 A 3 A 123 B 115 B 107 B 99 B 91 B 83 B 75 B 67 B 59 B 51 B 43 B 35 B 27 B 19 B 11 B 3 B 8 10 BASE 2 10 BASE 2 10/100 BASE T 10/100 BASE T GSC LOOP NODE THRU BUS 124 A 124 B 125 A 125 B 116 A 116 B 117 A 117 B 108 A 108 B 109 A 109 B 100 A 100 B 101 A 101 B 92 A 92 B 93 A 93 B 84 A 84 B 85 A 85 B 76 A 76 B 77 A 77 B 68 A 68 B 69 A 69 B 60 A 60 B 61 A 61 B 52 A 52 B 53 A 53 B 44 A 44 B 45 A 45 B 36 A 36 B 37 A 37 B 28 A 28 B 29 A 29 B 20 A 20 B 21 A 21 B 12 A 12 B 13 A 13 B 4 A 4 B 5 A 5 B A 118 A 110 A 102 A 94 A 86 A 78 A 70 A 62 A 54 A 46 A 38 A 30 A 22 A 14 A 6 A 7 VIDEO VIDEO REF 1 REF 2 1 LOOP THRU MONITOR 2 (2) 126 B 127 A 127 B 118 B 119 A 119 B 110 B 111 A 111 B 102 B 103 A 103 B 94 B 95 A 95 B 86 B 87 A 87 B 78 B 79 A 79 B 70 B 71 A 71 B 62 B 63 A 63 B 54 B 55 A 55 B 46 B 47 A 47 B 38 B 39 A 39 B 30 B 31 A 31 B 22 B 23 A 23 B 14 B 15 A 15 B 6 B 7 A 7 B A 128 B 120 A 120 B 112 A 112 B 104 A 104 B 96 A 96 B 88 A 88 B 80 A 80 B 72 A 72 B 64 A 64 B 56 A 56 B 48 A 48 B 40 A 40 B 32 A 32 B 24 A 24 B 16 A 16 B 8 A 8 B ALARMS 5 TIMECODE OUTPUTS AIR EXHAUST KEEP CLEAR 6" MIN AIR EXHAUST KEEP CLEAR 6" MIN FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN FAN FAN 2 POWER INPUT INPUTS POWER INPUT POWER SUPPLY MONITORS AIR EXHAUST KEEP CLEAR 6" MIN FAN FAN SERVICE ACCESS AIR EXHAUST KEEP C;EAR 6" MIN AIR EXHAUST KEEP CLEAR 6" MIN 4 INPUTS NVISION, INC. ENVOY Figure 1-7. NV6256 Rear Page 1-19

32 NV6256 Specifications TYPE Electrical AC Power Fuses Connectors Power Consumption Regulatory Mechanical Module Slots Power Supply Slots Table 1-3 lists the specifications for the NV6256 Universal Digital Router. Table 1-3. NV6256 FRAME SPECIFICATIONS PARAMETER / VAC, 50/60Hz, Auto-ranging Crosspoint Module - 7A, 125V (F) F1 Fast & 1A, Auto Reset. I/O Modules - 1A, Auto Reset. Controller Module - 3A, 125V (F) F1 Fast. Power Supplies - 8.0A, V; 6.3A, V. 8, IEC Filtered AC 2640 Watts (maximum) UL Listed and CE Compliant 32 Input modules, 8 channels each. 16 Output modules, 8 channels each x32 Crosspoint modules. 2 Controller modules (1 Primary, 1 Optional Secondary). 1 Output Monitor module (Optional). 8 (4 Main, 4 Optional Redundant) in separate frame Dimensions EIA Standard: Electronics Frame (24 RU High) 42.0 (1,066.8mm) H x 19.0 (482.6mm) W x 19.0 (482.6mm) D; EIA Standard: Power Supply Frame (5 RU High) 8.75 (222.2mm) H x 19.0 (482.6mm) W x 19.0 (482.6mm) D Weight (fully loaded) Electronics Frame: lbs (119.2kg) Power Supply Frame: lbs (44.2kg) Inputs/Outputs Input/Output specifications follow SMPTE standards for SDI (259M) and HD-SDI (292M) signals, where applicable. Cable Equalization Automatic, designed for Belden (HD) or Belden 8281 at 270Mb/ s (SD) Video Ref Input Type Analog PAL and/or NTSC Color Black Connectors 4 BNC (2 pairs), Loop-thru Return Loss >30dB to 5MHz Performance Reclocking Yes Input to Output Delay <10ns Crosspoint Granularity 128x32 GSC Node Bus For Tektronix SMS7000 Control System External Communications Port Type RS-422 Serial Ports, usage determined by software Connectors 6, 9-pin, D-type (2 Primary, 2 Secondary, 2 Diagnostic) External Alarm Port 1 D-type, 9-pin connector Environmental Operating Temperature 0 to 40 degrees Centigrade, Ambient Relative Humidity 0 to 90%, non-condensing Page 1-20

33 NV8256 SYSTEM DESCRIPTION The NV8256 Universal Digital Router system consists of two frames. One frame houses the electronics and the other contains the power supplies. The electronics frame is 22 RUs high and the Power Supply frame is 5 RUs high. Both frames are designed to be installed in a standard 19 equipment rack. In addition to those discussed on the previous pages, features of the NV8256 include: Optional N-on-1 redundant crosspoint card. Optional redundant power supplies. Optional secondary control card. Front and rear panels for the 8256 electronics frame are described below, followed by specifications for the NV8256. Description and specifications for the 6257 power supply frame follow the NV8256 section. Page 1-21

34 NV8256 Electronics Frame Front Panel Figure 1-8 illustrates the NV8256 electronics frame front panel (door open). The front panel provides access to the following assemblies: Up to 16 Output boards (can be a combination of SDI and SWB), 16 outputs per board. Output Monitor (optional). Controller, Primary and Secondary (optional). Board is not slot dependent. Cooling fans pull air into the frame through the front door and up through the Crosspoint and I/O modules and exhaust air out through the rear of the frame. Up to 2 Crosspoint boards, 256 inputs x 128 outputs per board, plus an optional N-on-1 redundant crosspoint card. Up to 16 Input boards (can be a combination of SDI and SWB), 16 inputs per board. Crosspoint fan filter. Page 1-22

35 4 FAN 1 OUTPUT MONITOR 1 INPUTS 1-16 INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS OUTPUTS 1-16 OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS x128 CROSSPOINT OUTPUTS x128 CROSSPOINT OUTPUTS (REDUNDANT) 256x128 CROSSPOINT OUTPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS CONTROLLER - SECONDARY CONTROLLER - PRIMARY 3 Figure 1-8. NV8256 Electronics Frame Front Page 1-23

36 NV8256 Electronics Frame Rear Panel Figure 1-9 illustrates the NV8256 Electronics frame rear panel. The rear panel provides access to the following connectors: 256 Output Matrix BNC connectors. Power input connectors. Connect to 6257 Power Supply frame using supplied power input cables. Power supply monitor connector. Connect to 6257 Power Supply frame using supplied monitor cables. 256 Input Matrix BNC connectors. System Alarms connector. For connection details, see the heading, "Alarms Connector (all models)" on page Monitor inputs and outputs (optional). Video Reference Inputs 1 and 2. Connect analog PAL or NTSC composite video to these inputs. Looping connectors provided. Ethernet and SMS7000 GSC Node Bus connectors. Ethernet connectors are for use with NVISION NV9000 Series Control Systems, and GSC connectors are for use with GVGSMS7000 Control Systems. See the documentation for those systems for connection details. Serial Control and Diagnostic connectors. Connect your main control system to the Primary and Secondary CTRL 1 connectors. This provides control connections to the primary and secondary Controller modules. If you have a second alternate control system, use the Primary and Secondary CTRL 2 connectors. Use the DIAG connectors for connecting to a PC to run the supplied UniConfig router configuration software. See Figure 1-11 on page 1-29 for Control connector drawings and pin-outs, which are the same for all four control connectors. See the UniConfig manual for the diagnostic port pin outs. Remote control connector for redundant crosspoint. Note: Connectors not described here are reserved for future use. Page 1-24

37 Page 1-25 Figure 1-9. NV8256 Rear SEC CTRL PRI CTRL SEC CTRL PRI CTRL INPUTS INPUTS CONTROL NO. 9K50 PROFESSIONAL VIDEO/AUDIO E ENVOY 8256 VIDEO REF 2 VIDEO REF 1 ALARMS TIME CODE GSC NODE BUS LOOP THRU LOOP THRU LOOP THRU AES REF 1 10 B 2 10/100 BT NETWORK 10 B 2 10/100 BT NETWORK C TR L 1 C TR L 2 D IA G C TR L 1 C TR L 2 D IA G AES REF AIR EXHAUST KEEP CLEAR 6" MIN IN 1 IN 2 OUT 1 OUT POWER INPUT 1 MONITORS POWER INPUT 2 POWER SUPPLY MONITORS REDUNDANT CROSSPOINT CONTROL OUTPUTS OUTPUTS FAN FAN FAN

38 NV8256 Specifications Table 1-4 lists the specifications for the NV8256 Universal Digital Router. Table 1-4. NV8256 FRAME SPECIFICATIONS TYPE Electrical AC Power Fuses Connectors Power Consumption Regulatory Mechanical Module Slots Power Supply Slots Dimensions Weight (fully loaded) Inputs/Outputs Cable Equalization Video Ref Input Type Connectors Return Loss Performance Reclocking Input to Output Delay Crosspoint Granularity GSC Node Bus External Communications Port Type Connectors External Alarm Port Environmental Operating Temperature Relative Humidity PARAMETER / VAC, 50/60Hz, Auto-ranging Input Modules - Auto Reset Output Modules (T) SLOBLO Crosspoint Modules - 3 fuses, all 1.6A(T) SLOBLO Controller Module - 3A, 125V (F) F1 Fast. Power Supplies - 8.0A, V; 6.3A, V. 8, IEC Filtered AC 2640 Watts (maximum) UL Listed and CE Compliant 16 Input modules, 16 channels each. 16 Output modules, 16 channels each x128 Crosspoint modules, including optional redundant crosspoint. 2 Controller modules (1 Primary, 1 Optional Secondary). 1 Output Monitor module (Optional). 8 (4 Main, 4 Optional Redundant) in separate frame EIA Standard: Electronics Frame (22 RU High) 38.5 (997mm) H x 19.0 (482.6mm) W x 19.0 (482.6mm) D; EIA Standard: Power Supply Frame (5 RU High) 8.75 (222.2mm) H x 19.0 (482.6mm) W x 19.0 (482.6mm) D Electronics Frame: 228 lbs (103.4kg) Power Supply Frame: lbs (44.2kg) Input/Output specifications follow SMPTE standards for SDI (259M) and HD-SDI (292M) signals, where applicable. Automatic, designed for Belden (HD) or Belden 8281 at 270Mb/ s (SD) Analog PAL or NTSC Color Black 4 BNC (2 pairs), Loop-thru >30dB to 5MHz Yes <10ns 256x128 For GVG SMS7000 Control System RS-422 Serial Ports, usage determined by software 6, 9-pin, D-type (2 Primary, 2 Secondary, 2 Diagnostic) 1 D-type, 9-pin connector 0 to 40 degrees Centigrade, Ambient 0 to 90%, non-condensing Page 1-26