LED SIGNAL DOME RELIABLE USER INTERACTION. starts in the design process of the machine

Transcription

1 LED SIGNAL DOME RELIABLE USER INTERACTION starts in the design process of the machine I N D I C AT O R S U P P L E M E N T

2 B THREE COLOR LED SIGNAL DOME Features Modern compact and space optimized design Very bright optical status indication High efficient vibration proof LED technology Consumes up to 90% less power than incandescent bulbs Several blink patterns per color, that are easily programmable 100% water and oil tight IP67 Breakproof polycarbonate cover and metal housing Suitable for use in foodrelated and pharmaceutical applications Fits into standard Ø22.5 mm mounting holes Available with industrial Direct and lowcurrent inputs as well as several bus protocols standard connector M12

3 The setting button is located behind the hole on the bottom of the SigDome (Picture 1). Use a small tool (Ø 2 mm), which comes with the device to press and hold the teachbutton for more than 1 second. For your convenience, the brightness is dimmed during programming. PROGRAMMING While in programming mode, press the button to select the color you want to change. Each color you select shows its current blinkpattern, regardless of its correspondig input status. To change the blink pattern of the selected color, press and hold the setting button for more than 1 second. Press the button to switch from one pattern to another and more than 1 second to finish programming. To program another color, start the procedure from the beginning. permanent slow fast very fast PATTERNS two blips fast blips very fast blips Each color is driven through its corresponding input. The color selection output needs to be able to source the full current. If more than one color is engaged at the same time, then the SignalDome begins to cycle resp. alternate these colors. During cycling, no blink pattern will be applied. 1/+ brown braun 3/+ black schwarz 2/+ white weiß 4/ blue blau 3/I black schwarz /I white weiß /+ brown braun 4/ blue blau CONNECTION Low Current Input The SignalDome is supplied by the brown wire only. The two auxiliary inputs form a binary register which selects the color shown. The inputs are 3 VDC tolerant. Alternatively, several businterfaces are also available. These allow the direct selection of the blink patterns as well as the brightness.

4 SD ALUMINUM LowCurrent Input TECHNICAL DATA Reverse Polarity Protection Power Consumption (2) Maximum Inrush Current (2) Auxiliary Inputs 3 30 VDC, < 3 ma Protocol Layer Rcmd. max. Frequency Indicator Type Wave Length, Red Wave Length, Green Wave Length, Blue Operating Voltage LowCurrent Input Wave Length, Yellow Operating Temperature Protection Class Bulb Material Housing Material (2) Aluminum ORDER CODES RedGreenYellow Connector M12 RedGreenYellow Cable 2 m SDAPWRGYN12 SDAPWRGYN2P SDALCRGYN12 SDALCRGYN2P RedGreenBlue RedGreenBlue SDAPWRGBN12 SDAPWRGBN2P SDALCRGBN12 SDALCRGBN2P Connector M12 Cable 2 m

5 IOLink transceiver isolated CAN transceiver isolated RS485 transceiver IODD V1.1 CANopen Modbus RTU SDAIORGYN12 SDAIORGYN2P SDACORGYN12 SDACORGYN2P SDAMBRGYN12 SDAMBRGYN2P SDAIORGBN12 SDAIORGBN2P SDACORGBN12 SDACORGBN2P SDAMBRGBN12 SDAMBRGBN2P

6 SD STAINLESS LowCurrent Input TECHNICAL DATA Reverse Polarity Protection Power Consumption (2) Maximum Inrush Current (2) Auxiliary Inputs 3 30 VDC, < 3 ma Protocol Layer Rcmd. max. Frequency Indicator Type Wave Length, Red Wave Length, Green Wave Length, Blue Operating Voltage LowCurrent Input Wave Length, Yellow Operating Temperature Protection Class Bulb Material Housing Material (2) Stainless Steel ORDER CODES RedGreenYellow Connector M12 RedGreenYellow Cable 2 m SDSPWRGYN12 SDSPWRGYN2P SDSLCRGYN12 SDSLCRGYN2P RedGreenBlue RedGreenBlue SDSPWRGBN12 SDSPWRGBN2P SDSLCRGBN12 SDSLCRGBN2P Connector M12 Cable 2 m

7 IOLink transceiver isolated CAN transceiver isolated RS485 transceiver IODD V1.1 CANopen Modbus RTU SDSIORGYN12 SDSIORGYN2P SDSCORGYN12 SDSCORGYN2P SDSMBRGYN12 SDSMBRGYN2P SDSIORGBN12 SDSIORGBN2P SDSCORGBN12 SDSCORGBN2P SDSMBRGBN12 SDSMBRGBN2P

8 XECRO GmbH Siemensstr. 31 : 308 Garbsen : Germany support@xecro.com April 2015 SD copyright by XECRO INTERNATIONAL