IVS SDA-904 Mounting and Connections

Transcription

1 IVS SDA-904 Mounting and Connections

2 Notice Copyright 2014 RMG Enterprise Solutions, Inc. All Rights Reserved. This publication is protected by copyright and all rights are reserved. No part of this book may be reproduced or transmitted by any means or in any form, without prior written consent from RMG Enterprise Solutions, Inc. The information in this publication has been carefully checked and is believed to be accurate. RMG Enterprise Solutions, Inc. assumes no liability for any inaccuracies that may be found in this publication. In the interest of continued product development, RMG Enterprise Solutions, Inc. reserves the right to make improvements to this publication and the products it describes at any time without notice or obligation. Publication Date RMGN-DOC-IVS-SDA cmgpdf June 2014 To access the latest version of this document, go to: Connections.pdf 2

3 Contents FCC Verification, Industry Canada & European CE Information FCC Industry Canada Important Safety Instructions Mounting the IVS SDA Attaching Mounting Plate A to the SDA Horizontal Wall Mount Vertical Wall Mount VESA-Compliant Display Mounts Connecting the IVS SDA IVS SDA-904 Diagram Step-by-Step Connections for the IVS SDA IVS SDA-904 Specifications Physical Dimensions Hardware Components Power Requirements Getting Help and Support Contacting Technical Support Accessing the RMG Networks Support Web Site

4 FCC Verification, Industry Canada & European CE Information FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. WARNING: Changes or modifications to this device not expressly approved by RMG Networks could void the user's authority to operate the equipment. Industry Canada This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4

5 Important Safety Instructions This device has undergone various tests in order to comply with safety standards. Inappropriate use may be dangerous. Please follow the instructions in this guide to ensure your safety during the installation and operation of the device. For safety and proper operation, keep in mind the following factors: It is important that your IVS SDA-904 be properly ventilated. Do not fully enclose the IVS SDA-904 in any type of recess, cabinet, kiosk, hole, nook, or enclosure unless there are fans or a passive thermal exhaust that can constantly bring in new air to replace the trapped air in the space around the outside of the device. Place the IVS SDA-904 in a location free from dust and other particles. Ambient temperature should be between 32 F to 104 F (0 C to +40 C) in a noncondensing environment. With the above factors in mind, please be aware of the following section from your hardware maintenance contract: In the event that Hardware Maintenance is required due to: (i) abuse or mishandling of the Hardware by Customer, or (ii) any environmental conditions where the Hardware is located (dust, moisture, etc.), or (iii) any other technical issues (electrical spikes or the like), or (iv) any other external factors outside the normal operating conditions for the Hardware; then the charges for Maintenance associated therewith shall be paid by Customer. 5

6 Mounting the IVS SDA-904 The IVS SDA-904 includes hardware for installing the unit in a simple wall mount configuration or on the back of a VESA-compliant display. Do not throw away any cables, adapters, or other hardware that you might receive with the product you may need them for future use if you should ever upgrade the IVS SDA-904. (1) IVS SDA-904 Unit (1) Mounting Plate A (for bottom of SDA) (1) Mounting Plate B (for wall or back of display) (4) Small Phillips Flat Head Machine Screws (4) Medium Phillips Flat Head Machine Screws (4) Phillips Pan Head Machine Screws (2) Wireless Antennas (1) Power Supply (1) Power Cord 6

7 Attaching Mounting Plate A to the SDA Mounting Plate A is designed to attach to the bottom side of the IVS SDA-904 and is required when you want to mount the SDA on a wall or on the back of a display device. 1. Turn the SDA upside down and turn the unit around so that the front faces to the left and the back faces to the Mounting Plate A right. 2. Place Mounting Plate A over the bottom side of the SDA with the round rubber feet facing downwards. Insert a small Phillips flat head machine screw into each of the four holes on the mounting plate. 3. Use a Phillips screwdriver to turn each machine screw clockwise until the mounting plate is secure against the bottom of the SDA. 7 Mounting Plate A Attached to Bottom of SDA

8 Horizontal Wall Mount It is important that your IVS SDA-904 be properly ventilated and placed in a location with the ambient temperature between 32 F to 104 F (0 C to +40 C). See page 5 for specific details. 1. Use a Phillips screwdriver to attach two of the large Phillips pan head machine screws to one end of Mounting Plate B. 2. Align the flat side of Mounting Plate B against the wall area where you want to install the SDA. Allow for at least 9.0 of clearance on the open-ended side of the mounting bracket (i.e., the side opposite to the one on which you installed the large pan head screws). 3. Use four screws (not supplied) to attach the mounting plate to the wall. Allow for 9.0" clearance on the open-ended side of the mounting bracket. 8

9 4. Attach Mounting Plate A to the bottom side of the SDA using the steps on page Turn the SDA so that the Power Button is on the top-right side of the unit and the controls are on the left. This orientation allows the Power Button to be easily accessible from the right side and allows air to circulate freely from the top and sides of the unit. 6. Hold the SDA next to the open end of Mounting Plate B, then slide it sideways so that Mounting Plate A fits snugly within Mounting Plate B. The pan head machine screws that you installed in step 1 will hold the SDA in place and prevent you from sliding the SDA too far within the mounting plate. Controls on Left 9.0" Clearance Power Button on Right Machine Screws 7. (Optional) If you are using wireless communications, attach the two antennas to the connections on the left side of the unit. (Pages 25 and 26 illustrate the space requirements for the antennas when fully extended or bent at a 90 angle.) 8. Refer to the instructions on page 20 to connect the IVS SDA-904. Leave antennas fully extended or bend to 90. 9

10 Vertical Wall Mount It is important that your IVS SDA-904 be properly ventilated and placed in a location with the ambient temperature between 32 F to 104 F (0 C to +40 C). See page 5 for specific details. 1. Use a Phillips screwdriver to attach two of the large Phillips pan head machine screws to one end of Mounting Plate B. 2. Align the flat side of Mounting Plate B against the wall area where you want to install the IVS SDA-904. Allow for at least 9.0 of clearance above the mounting plate before you attach it to the wall. 3. Use four screws (not supplied) to attach the mounting plate to the wall. Allow for 9.0" clearance above the mounting plate 10

11 4. Attach Mounting Plate A to the bottom side of the SDA using the steps on page Turn the SDA so that the Power Button is on the bottomside of the unit and the controls are on top. This allows Controls on Top the Power Button to be easily accessible from below, and allows air to circulate freely from the sides of the unit. Power Button on Bottom 6. Hold the SDA above Mounting Plate B and slide it downwards so that Mounting Plate A fits snugly within Mounting Plate B. The pan head machine screws that you installed in step 1 will hold the SDA in place within the mounting plate. 9.0" Clearance Mounting Plate B Machine Screws Wall 11

12 7. (Optional) If you are using wireless communications, attach the two antennas to the connections at the top of the unit. (Pages 25 and 26 illustrate the space requirements for the antennas when fully extended or bent at a 90 angle.) 8. Refer to the instructions on page 20 to connect the IVS SDA-904. Leave antennas fully extended or bend to

13 VESA-Compliant Display Mounts It is important that your IVS SDA-904 be properly ventilated and placed in a location with the ambient temperature between 32 F to 104 F (0 C to +40 C). See page 5 for specific details. Mounting Plate B is compatible for mounting against the back of a display that has a 75 mm x 75 mm or 100 mm x 100 mm VESA MIS-D hole mount pattern. Use the hole mount pattern on Mounting Plate B that matches the pattern on the back of your display. 100 mm 75 mm 100 mm 75 mm 75 mm 100 mm 75 mm 100 mm FIGURE mm x 75 mm and 100 mm x 100 mm mount patterns 1. Use a Phillips screwdriver to attach two of the large Phillips pan head machine screws to one end of Mounting Plate B. 13

14 2. Align the flat side of Mounting Plate B against the back of the display at the location where you want to mount the SDA. You can install the mounting plate in a horizontal or vertical position. Horizontal Mount Vertical Mount 3. Use a Phillips screwdriver and the four medium-sized Phillips flat head machine screws to secure the mounting plate to the back of the display. Horizontal Mount Vertical Mount 14

15 4. Attach Mounting Plate A to the bottom side of the SDA using the steps on page 7, then continue with step 5a or 5b. 5a. For a horizontal mount, turn the SDA so that the Power Button is on the top-right side of the unit and the controls are on the left. This orientation allows the Power Button to be easily accessible from the right side and allows air to circulate freely from the top and sides of the unit. Hold the SDA next to the open end of Mounting Plate B, then slide it sideways so that Mounting Plate A fits snugly within Mounting Plate B. The pan head machine screws that you installed in step 1 will hold the SDA in place and prevent you from sliding the SDA too far within the mounting plate. Controls on Left Horizontal Mount Power Button on Right Machine Screws 15

16 5b. For a vertical mount, turn the SDA so that the Power Button is on the bottom-side of the unit and the controls are on top. This orientation allows the Power Button to be easily accessible from below, and allows air to circulate freely from the sides of the unit. Controls on Top Power Button on Bottom Hold the SDA above Mounting Plate B and slide it downwards so that Mounting Plate A fits snugly within Mounting Plate B. The pan head machine screws that you installed in step 1 will hold the SDA in place within the mounting plate. Display Device Mounting Plate B Machine Screws Vertical Mount (Side View) 16

17 6. (Optional) If you are using wireless communications, attach the two antennas to the wireless connections. Leave antennas fully extended or bend to 90. Horizontal Mount Vertical Mount FIGURE 2. VESA-Compliant Display Mounts 7. Refer to the instructions on page 20 to connect the IVS SDA

18 Connecting the IVS SDA-904 IVS SDA-904 Diagram The following diagram demonstrates how to connect your IVS SDA-904 model. (A key to the numbered parts is shown in Table 1 on page 19.) 1 2a 3 11a Front View Left Side View 5a 2b 7 2c 9 5b 11b Speaker Out Mic in VGA HDMI USB LAN USB DC Back View Right Side View FIGURE 3. IVS SDA-904 Connections 18

19 TABLE 1: IVS SDA-904 Functions Item # Description 1 RS-232 Serial Connector 2a, 2b, 2c USB 2.0 x (5) 3 Power Button 4 VGA connector 5a, 5b Wireless Antenna Connectors 6 HDMI Connector 7 10/100/1000 Gigabit Ethernet Connector 8 Speaker Out 9 Mic In 10 DC Input 11a, 11b Intake Vents 19

20 Step-by-Step Connections for the IVS SDA-904 Warning: Failure to set up your IVS SDA-904 sequentially according to the steps below may cause configuration difficulties or loss of functionality. Refer to Figure 3 on page 18 for the following connections: 1. Insert a standard Ethernet cable into the Ethernet port (7). 2. Use only one of the following output configurations at a time. - For VGA output, connect the male end of a VGA cable (not supplied) to the female VGA connector at the back of the device (4); connect the other end of the VGA cable to a video connection on the display device. - For HDMI output, connect the male end of an HDMI cable (not supplied) to the HDMI connector (6), then connect the other end of the HDMI cable to the HDMI connector on the display device. 3. Connect the female end of the power supply cable to the DC Input (10). 4. Connect the female end of the power cord to the three-prong connection on the power supply. Plug the other end of the power cord into a standard AC outlet. 5. Briefly press the power button (3) on the IVS SDA-904. The SDA welcome message appears on the output screen. Note: The first time you connect your SDA, the message One Moment Please may appear on the video display. Depending on your network, this message might appear for up to one minute. After that time a Welcome screen appears that displays the name of the SDA, its serial number, and the IP address that you'll need to set up your SDA. Use this IP address to access the Web Interface. 6. Refer to the following SDA configuration guide to configure your IVS SDA-904: 20

21 IVS SDA-904 Specifications Physical Dimensions Without Antennas or Mounting Plates Dimensions (L) x (W) x (H): mm x mm x mm ( x x ) Weight: 1.07 kg (2 lbs., 5.9 oz.) mm (7.5625") mm (1.5625") Front View mm (1.375") 4.76 mm (.1875") mm (7.5625") mm (1.5625") VGA HDMI USB LAN USB Back View Speaker Out Mic in DC mm (1.375") 4.76 mm (.1875") 21

22 mm (8.2812") mm (7.5625") mm (1.5625") mm (1.375") mm (1.5625") Right Side View 6.35 mm (.25") 12.7 mm (.50") mm (8.2812") mm (7.5625") mm (1.375") Left Side View 12.7 mm (.50") 6.35 mm (.25") 22

23 mm (7.5625") 12.7 mm (.50") mm (8.3125") mm (7.8125") mm (7.5625") Top View 6.35 mm (.25") 23

24 12.7 mm (.50") mm (7.5625") mm (7.5625") mm (8.3125") mm (7.8125") 6.35 mm (.25") Bottom View 24

25 With Mounting Plates & Antennas Fully Extended Dimensions (L) x (W) x (H): mm x mm x mm ( x x ) Weight: 1.26 kg (2 lbs., 12.4 oz.) mm (4.25") 1.59 mm (.0625") mm (7.5625") 6.35 mm (.25") mm (7.5625") mm (7.8125") Top View with Antennas Fully Extended 25

26 With Mounting Plates & Antennas Bent at 90 Dimensions (L) x (W) x (H): mm x mm x mm ( x x ) Weight: 1.26 kg (2 lbs., 12.4 oz.) 1.59 mm (.0625") mm (1.2188") mm (9.0938") mm (7.8125") mm (7.5625") 6.35 mm (.25") mm (1.375") mm mm (1.6875") (2.625") mm (4.3125") Left Side View 26

27 Hardware Components Front Panel IO Serial DB9 (COM Port): USB 2.0 Port: Power Button: Power indicator (green): Audio Type: LAN: x1 (Male connector) x1 x1 x1 HDMI 10/100/1000 Gigabit Rear Panel IO DC Jack: HDMI port: USB 2.0: VGA Port: Wireless Antenna Connection: x1 x1 x4 x1 b,g,n (2 x rear external antennas) 27

28 Power Requirements AC Input Frequency: 50/60Hz AC Input Voltage: 100 ~ 240V AC Input Current: 1.6A DC Input Current: 50/60Hz DC Output Current: 19V, 3.16A 28

29 Getting Help and Support Contacting Technical Support If you experience problems using your IVS SDA-904, please contact RMG Networks. Our main Web site is North American Customers - Contact RMG Networks Technical Support between 7:00 a.m. and 7:00 p.m., Central Standard Time (CST). Phone: Fax: Support support@rmgnetworks.com International Customers - Contact RMG Networks Technical Support between 08:00 and 18:00, Greenwich Mean Time (GMT). Phone: +44 (0) Fax: +44 (0) Support support@rmgnetworks.com Accessing the RMG Networks Support Web Site You can visit RMG Networks s support web site at There you can obtain answers to FAQs (frequently asked questions) and download product information. 29

30