panasonic.net/id/pidsx/global Machine safeguarding without sacrificing productivity
|
|
- Claribel Charles
- 5 years ago
- Views:
Transcription
1 531 Ultraslim Curtain Type 4 SERIES Related Information General terms and conditions... F7 SFC10... P.703~ General precautions... P.1458~ Sensor selection guide... P.497~ Glossary of terms... P.1455~ Korea s Smark... P.1506 PHOTO PHOTO Conforming to Machine & EMC Directive Certified by NRTL Certified [H (J05) only] Certified Conforming to OSHA / ANSI MEASURE ITY Category 4 PLe SIL3 Selfdiagnosis PNP output type available Machine safeguarding without sacrificing productivity Slim size for efficient applications Available work space is expanded from the previous model, and productivity is improved. Thinness 13 mm in panasonic.net/id/pidsx/global Previous Usable work space 83 % (414 mm in) diagnosis If the machine opening is 500 mm in Usable work space approx. 12 % UP (60 mm in) series Usable work space 95 % (474 mm in approx.) 43 mm in 43 mm in If the machine opening width is 500 mm in Shorter safety distance to downsize equipment Finger protection type The safety distance of series finger protection type is 84 mm 3.7 in shorter than that of series hard protection type (H ). As a result, the depth and guard of the equipment can be downsized. series Hand protection type Finger protection type distance 102 mm in 18 mm in Shortened by 84 mm 3.7 in * Calculation based based on ISO on ISO with ms with or longer 41 ms being or the longer machinery s being maximum the machinery's stopping time. maximum stopping time. 102 mm in Shortened by 84 mm 3.7 in 13.2 mm in 13.2 mm in If the machine opening width is 500 mm in 18 mm in 100 mm in min. * Hand protection type Finger protection type Characteristic Characteristic safety distance for safety distance the machinery's for light curtain maximum stopping time * The light curtain cannot be installed within a distance of 100 mm in. (ISO 13855)
2 Ultraslim Curtain Type 4 SERIES 532 Can be used in a variety of applications for simplified equipment [ multipurpose ] The bright LED s located in the center of both sides of each light curtain can be illuminated green or red by using external inputs. There is no need for setting up a separate, so that equipment is consolidated. * The lighting conditions of series can be changed by using a handycontroller SFCHC (optional). It is possible to actuate the lighting together with internal operation, regardless of connection of the large multipurpose input wires. Use as an operation Solid green Equipment is operating Solid red Emergency stop Use as an error Blinking red Error present Error blinking Normal Normal Confirm detail of error quickly on the digital display. * The photo is H F differs in the position of digital display. Use the handycontroller SFCHC (optional) to change lighting conditions. Beamaxis alignment s help to reduce startup time The beam channels of the light curtain are displayed in four blocks so that incident light position is shown at a glance. When the beam channel at the bottommost channel (or topmost channel), which is used as a reference for beamaxis alignments, is correctly aligned, the LED blinks red. After this, each block lights red as the beam axes successively become aligned. When all channel beam axes are aligned, all LEDs light green. The display also has a stability (STB) added so that setup can be carried out with greater stability. Green Red Green / Red Use as a muting lamp External input device (ing / blinking signal) multipurpose Input 1 Input 2 * If a failure diagnosis of muting lamp is needed as by the result of risk assessment, use the handycontroller SFCHC (optional) to change the setting, and connect the muting lamp output wire (red) of this light curtain to an incandescent lamp separately. Beamaxis alignment PHOTO PHOTO MEASURE ITY A single model supports both PNP and NPN polarities reducing model numbers PNP transistor output and NPN transistor output are combined in a single model. Overseas equipment that uses PNP, replacement with NPN sensors, factories that are positively grounded, and transfer of equipment overseas are all situations where the control circuits for a single model are suitable for use worldwide. IP67 protection structure An IP67 (IEC) rating is achieved with an ultraslim size for protection from environmental factors by a new method. weight! The series is made of resin that is approx. 45 % lighter than the conventional aluminum case type. Its lightweight body eases the burden on the mounting surface of the equipment and contributes to overall reduced weight during equipment transportation or overseas shipment. * Except the cable part A fast response time for all models H : 7 ms*, F : 9 ms* The series reduces the safety distance as well as the calculation work required for the safety distance among models with different beam channels. * When connecting safety sensors (light curtains, etc) to the safety input,the response time will be the total time of connected units. Mutual interference is reduced without needing for interference prevention lines The ELCA (Extraneous Check & Avoid) function automatically shifts the scan timing in order to avoid interference. Material suitable for manufacturing a secondary battery body is made of resin and the mounting bracket is made of Stainless Steel (SUS), so materials used are limited. Suitable for manufacturing secondary batteries or for food production equipment. Mounting bracket: SUS4 Mounting screw: SUSXM7* Body case: Polycarbonate alloy * Effective from production in November Reducing the number of malfunctions caused by extraneous light Double scanning method and retry processing are effective in eliminating the effects of extraneous light.
3 533 Ultraslim Curtain Type 4 SERIES PHOTO PHOTO MEASURE ITY Handycontroller SFCHC (Opitonal) enables the user to select a variety of settings Operation of the large multipurpose s can be configured Mode No (Note 1) 5 (Note 1) 6 (Note 1) 7 (Note 1) Operation of large multipurpose s (factory setting: mode 0) outputs Muting multipurpose multipurpose Override 1 2 (OSSD 1 / OSSD 2) function function High or Low High or Low Solid red Solid green Blinking red Blinking green Solid red Blinking green Blinking red Solid green Solid red Blinking red Blinking green Solid red Solid green Blinking red ON Solid green OFF Solid red Enabled Blinking green Notes: 1) The blinking condition is prioritized over the solid condition. Notes: 2) During lockout, it is possible to blink red. Lockout blinking function When lockout occurs Enabled Blinking red Disabled Auxiliary output has selectable output configuration, productivity, and cost reduction [Muting control function] The light curtain has a builtin muting control function that causes the line to stop only when a person passes through the light curtain, and does not stop the line when an object passes through. The muting sensors and muting lamps can be connected directly to the light curtain. Furthermore, the large multipurpose s can be used as muting lamps, which contribute to less wiring troubles, improvement of safety and productivity, and cost reduction. Enabled Solid green Blinking green Mode No. Description 0 Negative logic of the control outputs (OSSD 1, OSSD 2) (factory setting) 1 Positive logic of the control outputs (OSSD 1, OSSD 2) 2 For test input enabled: output OFF, For Disabled: output ON 3 For test input enabled: output ON, For Disabled: output OFF 4 For unstable incident beam: OFF (Note 1) 5 For unstable incident beam: ON (Note 1) 6 For muting: ON 7 For muting: OFF 8 For beam received: ON, For beam interrupted: OFF (Note 2) 9 For beam received: OFF, For beam interrupted: ON (Note 2) A For safety input enabled: ON, Disabled: OFF B For safety input enabled: OFF, Disabled: ON C For lockout: OFF D For lockout: ON Notes: 1) The output cannot be used while the fix blanking function, floating blanking function or the muting function is activated. 2) This device outputs the beam received / interrupted state under activating the auxiliary output switching function using the handycontroller irrespective of activating other functions, fixed blanking function, floating blanking function, and muting function. series Previous SFCHC Fixed blanking function which allows selective beam channels to be activated improves productivity The series is equipped with a fixed blanking function which allows specific beam channels to be selectively interrupted without causing the control output (OSSD) to output the OFF signal. This function is convenient for use with applications in which certain fixed obstacles tend to interrupt specific beam channels. Floating blanking function which allows nonspecified beam channels to be deactivated improves productivity 1, 2 or 3 nonspecified beam channels can be deactivated. This function is useful in the event when an object passes through the light curtain s sensing area. curtain Note: When the floating blanking function is used, the size of the min. sensing object is changed. Muting lamps Muting lamps Muting unit Muting sensors Muting sensors circuit ( relay, etc.) circuit ( relay, etc.) HC series * If a failure diagnosis of muting lamp is needed as by the result of risk assessment, use the handycontroller SFCHC (optional) to change the setting, and connect the muting lamp output wire (red) of this light curtain to an incandescent lamp separately.
4 Ultraslim Curtain Type 4 SERIES 534 Selective muting area [Separate muting control function for each beam channel] The handycontroller SFCHC (optional) can be used to carry out muting control for specified beam channels only. Because individual beam channel can be specified to suit the object, separate guards to prevent entry do not need to be set up. Muting at the exit of a machine is now possible using the handycontroller SFCHC (optional). Just set a Max. four sec. delay timer on the muting sensors located at the exit. This is efficient for places with no installation space for muting sensors and also reduces cost and wiring. While muting control is active (line operating) measures when objects exit [Exit muting control function] Entrance side Line stopped For example, depending on the height of the object, the muting function can be activated for 10 beam channels starting from the bottom most, so that if the 11th or subsequent beam channels are interrupted, it is judged that a person has entered the area and the line stops. Exit side HC HC PHOTO PHOTO MEASURE ITY Muting sensors are not needed on the exit side! The light curtain has a builtin external device monitoring function (such as deposited relay monitoring) and an interlock function. This allows a safety circuit to be constructed so that a separate safety relay unit is not needed, and the control box has become smaller to help to achieve to lower costs. By installing muting sensors only within the dangerous zone and setting up a delay timer on the sensor, muting control is made possible even on the exit side where muting sensors cannot be installed. circuit is constructed without the need for a safety relay unit [External device monitoring function] series Previous series Reset input curtain relay unit relays Motor, etc. Reset input Monitoring Monitoring relays Motor, etc. The light curtain can directly connect to external devices (safety relay, etc) without an exclusive control unit. This allows for simplified equipment, cost reduction, and error prevention.
5 535 Ultraslim Curtain Type 4 SERIES PHOTO PHOTO Industry first*! Wiresaving when connecting to safety devices [ input function] Contact outputs such as an emergency stop switches or a safety door switches can be connected to the light curtain. Also, by using the handycontroller SFCHC (optional) up to three sets of light curtains can be cascade connected for a consolidated safety output. * Based on research conducted by our company as of March 2009 Direct connection of safety devices Monitoring Previous 2NC door switch, emergency stop switch, etc. Monitoring 2NC series door switch, emergency stop switch, etc. MEASURE ITY curtain relays Contactor relay unit Motor, etc. A safety relay unit is needed for connecting safety devices other than light curtain. series relays Contactor Motor, etc. Direct connection of various safety devices is possible for a simplified safety circuit. By using the handycontroller SFCHC (optional) up to three sets of light curtains can be cascade connected for a consolidated safety output. (Note) curtain Monitoring Monitoring Monitoring Previous 2NC Two safety relays are needed for each set of light curtain door switch, emergency stop switch, etc. Contactor relay unit Three sets of light curtains require three sets of safety relays. Motor, etc. Note: This setting is possible with the use of handycontroller SFCHC (optional) for series Ver.2.1 or later. Individual monitoring by auxiliary output series 2NC series Monitoring door switch, emergency stop switch, etc. Just two safety relays are enough Contactor Outputs of safety devices are consolidated in one unit. HC Motor, etc. Individual monitoring on light curtains is possible while the outputs of three sets of light curtains and other safety devices are consolidated in one unit.
6 Ultraslim Curtain Type 4 SERIES 536 PRODUCT CONFIGURATION Maintenance is prioritized Pigtailed type (with mounting bracket, connector attached cable) Standard mounting bracket MSSFC1 (Accessory) 1 Connector attached cable 0.5 m ft 4 3 Basic set in one model No. Cable type [Mounting bracket, with 5 m ( ft) cable] Standard mounting bracket MSSFC1 (Accessory) 2 Cable 5 m ft (discrete wire) PHOTO PHOTO ORDER GUIDE 1 2 curtains Type Appearance Operating range (Note 1) Model No. (Note 2) 1 Pigtailed type 2 Cable type Number of beam channels Protective height (mm in) MEASURE ITY Finger protection type Min. sensing object ø14 mm ø0.551 in (10 mm in beam pitch) Beam channel No. Beam pitch 10 mm in 10 mm in Protective height 10 mm in 0.1 to 3 m to ft F15J05 F mm in F23J05 F mm in F31J05 F mm in F39J05 F mm in F47J05 F mm in F55J05 F mm in F63J05 F mm in Hand protection type Min. sensing object ø25 mm ø0.984 in (20 mm in beam pitch) Beam channel No. Beam pitch 20 mm in 10 mm in Protective height 10 mm in 0.1 to 3 m to ft Notes: 1) The operating range is the possible setting distance between the emitter and the receiver. Receiver cannot be placed in this range 0.1 m ft Actual operating range of the light curtain Setting range of the receiver 3 m ft H8J05 H mm in H12J05 H mm in H16J05 H mm in H20J05 H mm in H24J05 H mm in H28J05 H mm in H32J05 H mm in Emitter Receiver Receiver 2) The model No. with suffix E shown on the label affixed to the product is the emitter, D shown on the label is the receiver.
7 537 Ultraslim Curtain Type 4 SERIES ORDER GUIDE 3 4 Mating cables PHOTO PHOTO Mating cables Type Appearance Model No. Description With connector on one end 3 With connectors on both ends 4 For emitter For receiver SFBCC3MU SFBCC7MU SFBCC10MU SFBCCJ3EMU SFBCCJ10EMU SFBCCJ3DMU SFBCCJ10DMU Length: 3 m ft Net weight: 4 g approx. (2 cables) Length: 7 m ft Net weight: 1,000 g approx. (2 cables) Length: 10 m ft Net weight: 1,0 g approx. (2 cables) Length: 3 m ft Net weight: 190 g approx. (1 cable) Length: 10 m ft Net weight: 660 g approx. (1 cable) Length: 3 m ft Net weight: 0 g approx. (1 cable) Length: 10 m ft Net weight: 680 g approx. (1 cable) Cable with connector on one end for pigtailed type Two cables per set for emitter and receiver Cable color: Gray (for emitter), Gray with black line (for receiver) Connector color: Gray (for emitter), Black (for receiver) The min. bending radius: R6 mm R0.236 in Cable with connectors on both ends for pigtailed type Cable color: Gray (for emitter), Gray with black line (for receiver) Connector color: Gray (for emitter), Black (for receiver) The min. bending radius: R6 mm R0.236 in MEASURE ITY Spare parts (Accessories for light curtain) Designation Model No. Description Standard mounting bracket Test rod ø14 Test rod ø25 MSSFC1 TR14 TR25 Allows the light curtain to be mounted at the rear with one M5 hexagonsockethead bolt. Mounting direction of the bracket can be selected between vertical or horizontal (no dead zone). (4 pcs. per set for emitter and receiver) Min. sensing object for regular checking (ø14 mm ø0.551 in) Min. sensing object for regular checking (ø25 mm ø0.984 in) Standard mounting bracket MSSFC1 M5 hexagonsockethead bolt Purchase separately. Four bracket set Four M3 (length: 4 mm in) countersunk screws <Mountable in three directions> curtain curtain Standard mounting bracket MSSFC1 (Accessory) M3 (length: 4 mm in) countersunk screw with looseproof agent
8 Ultraslim Curtain Type 4 SERIES 538 Mounting brackets Designation Model No. Description NA2N compatible mounting bracket Versatile bracket Intermediate supporting bracket for versatile bracket MSSFC2 MSSFC3 MSSFC4 Used when changing over area sensor NA2N series to the series. The mounting holes of NA2N series can continue to be used. Center mounting by a M6 hexagonsockethead bolt is also possible. (4 pcs. per set for emitter and receiver) Two ways of mounting are possible. 1 Rear mounting which enables beam adjustment 2 Dead zoneless center mounting on aluminum frame (4 pcs. per set for emitter and receiver) Used to support the light curtain in the middle. Be sure to purchase it when using the versatile bracket MSSFC3(optional) on F55(J05),F63(J05), H28(J05) or H32(J05). (2 pcs. per set for emitter and receiver) NA2N compatible mounting bracket MSSFC2 Mounting holes for M4 screw M4 screw Purchase separately. Mounting hole for M6 hexagonsockethead bolt curtain PHOTO PHOTO Versatile bracket MSSFC3 <Rear mounting> Mounting holes for M4 screw Mounting hole for M6 hexagonsockethead bolt <Dead zoneless mounting> Mounting hole for M6 hexagonsockethead bolt Mounting holes for M4 screw Intermediate supporting bracket for versatile bracket MSSFC4 Mounting hole for M6 hexagonsockethead bolt (Mount on either one) MEASURE ITY unit Designation Appearance Model No. Description Slim type control unit SFC13 Use a discrete wire cable to connect to the light curtain. Relay output. Compatible with up to Category 4. Recommended safety relay relay Panasonic Corporation SF series relay SFS3LDC24V (AG1S132) SFS4LDC24V (AG1S142) DIN terminal block SFS4SFD (AG1S847) SFS6SFD (AG1S867) Note: Contact Panasonic Corporation for details on the recommended products. Type With LED Item Model No. SFS3LDC24V SFS4LDC24V Contact arrangement 3a1b 4a2b Rated nominal switching capacity 6 A / 250 V AC, 6 A / V DC Min. switching capacity 1 ma / 5 V DC Coil rating 15 ma / 24 V DC 20.8 ma / 24 V DC Rated power consumption 360 mw 500 mw Operation time 20 ms or less Release time 20 ms or less Ambient temperature 40 to +85 C 40 to +185 F (Humidity: 5 to 85 % RH) Applicable standards UL, CUL, TÜV, Korea's Smark
9 539 Ultraslim Curtain Type 4 SERIES PHOTO PHOTO Yshaped connectors Type Appearance Model No. Description Wiresaving Yshaped connector Cable with connector on one side SFCWY1 WY1CCN3 WY1CCN10 Wiresaving connector for F J05 and H J05. Cables of emitter and receiver are consolidated into one cable for wiresaving. Wiring has +24 V, 0 V, OSSD 1, OSSD 2, output polarity setting wire (shield), large multipurpose input 1, and large multipurpose input 2 only. Power wire and synchronization wire are connected inside the connector. Interlock is disabled (automatic reset). Cable length: 3 m ft Net weight: 200 g approx. (1 cable) Cable length: 10 m ft Net weight: 620 g approx. (1 cable) Mating cable for Yshaped connector Cable color: Gray (with black line) Connector color: Black The min. bending radius: R6 mm R0.236 in By using the Yshaped connector, the least required wires such as power or safety output are consolidated into one cable. Manhours taken for wiring is eliminated to the minimum. Construction times as well as wiring mistakes are greatly reduced. MEASURE ITY Previous A total of 24 wires Yshaped connector Only 7 wires Less wiring mistakes! Reduced wiring time! Easy wiring to, etc. series series / Remote I/O relay unit SFC13 CCLink system remote I/O unit SFCL1T264T / Remote I/O relay unit SFC13 CCLink system remote I/O unit SFCL1T264T Product configuration Emitter Receiver Extension cable (1 cable for receiver) Extension cable Pigtailed type 0.5 m ft SFBCCJ3DMU (3 m ft for receiver) SFBCCJ10DMU (10 m ft for receiver) Extension cable (1 cable for emitter) SFBCCJ3EMU (3 m ft for emitter) SFBCCJ10EMU (10 m ft for emitter) Yshaped connector SFCWY1 SFBCCJ3D (3 m ft) SFBCCJ10D (10 m ft) Cable with connector on one side (Common for all models) WY1CCN3 (3 m ft) WY1CCN10 (10 m ft)
10 Ultraslim Curtain Type 4 SERIES 540 Connector pin layout Receiver Emitter Black connector Gray connector Connector pin No. 1 OSSD V 3 OSSD 1 4 Not used Description 5 multipurpose input 1 6 multipurpose input V 8 Output polarity setting wire (Shield) PHOTO PHOTO Wiring diagram of control unit SFC13 <For PNP output (minus ground)> Connect the light curtain control outputs OSSD 1 and OSSD 2 to S1 and S2 respectively. <For NPN output (plus ground)> Connect the light curtain control outputs OSSD 1 and OSSD 2 to S4 and S2 respectively and ground the + side. WY1CCN +24 V (Brown) +24 V DC A1 A2 0 V 0V (Blue) F S1 Output polarity setting wire (Shield) curtain ( series) Yshaped connector OSSD 1 (Black) OSSD 2 (White) Ui SFC13 control circuit K2 OUT INTER_LOCK ULT AUX KB L1L2L3 F.G. KA, KB: Forceguided relay or magnet contactor KA KB KA N 3 M ~ Notes: 1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentarytype switch as the reset (RESET) button. 3) Unused wires must be insulated. L1 K1 Not used (Yellowgreen) RESET (Note 1) (Note 2) (Note 1) F1 F2 S2 S3 S4 X1 X2 X Not used (Gray) Not used (Gray / Black) +24 V DC F.G. A2 0 V WY1CCN +24 V (Brown) A1 Ui F Output polarity setting wire 0 V (Shield) (Blue) OSSD 2 (White) OSSD 1 (Black) S1 S2 S3 S4 SFC13 control circuit OUT curtain ( series) Yshaped connector AUX KA, KB: Forceguided relay or magnet contactor X1 X2 X INTER_LOCK 3 M ~ Notes: 1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentarytype switch as the reset (RESET) button. 3) Unused wires must be insulated. L1 (Note 1) F1 K1 K2 ULT KA N Not used (Yellowgreen) F KB Not used (Gray) Not used (Gray / Black) RESET (Note 1) (Note 2) L1L2L3 KB KA MEASURE ITY
11 control CANCEL FUNCTION ENTER CANCEL FUNCTION ENTER 541 Ultraslim Curtain Type 4 SERIES PHOTO PHOTO MEASURE ITY curtain individual specifications Type Min. sensing object ø14 mm ø0.551 in type (10 mm in beam pitch) Pigtailed type F15J05 F23J05 F31J05 F39J05 F47J05 F55J05 F63J05 Item Cable type F15 F23 F31 F39 F47 F55 F63 No. of beam channels Protective height 160 mm in 240 mm in 320 mm in 400 mm in 480 mm in 560 mm in 640 mm in Current consumption Handycontroller Metal protection case Applicable beam channels SPECIFICATIONS Model No. multipurpose lights off multipurpose lights up Emitter: 70 ma or less Receiver: 80 ma or less Emitter: 105 ma or less Receiver: 110 ma or less Emitter: 75 ma or less Receiver: 85 ma or less Emitter: 110 ma or less Receiver: 115 ma or less Emitter: 80 ma or less Receiver: 90 ma or less Emitter: 115 ma or less Receiver: 120 ma or less Emitter: 85 ma or less Receiver: 95 ma or less Emitter: 120 ma or less Receiver: 125 ma or less PFHd* MTTFd* 100 years or more Net weight Total of emitter and receiver Pigtailed type Designation Metal protection case (2 pcs. per set for emitter and receiver) F H Model No MSSFCH MSSFCH MSSFCH MSSFCH MSSFCH MSSFCH MSSFCH32 MSSFCH8 MSSFCH12/16/20/24/28/32 0 g approx. 270 g approx. 340 g approx. 400 g approx. 470 g approx. 540 g approx. 600 g approx. Cable type 600 g approx. 670 g approx. 7 g approx. 800 g approx. 860 g approx. 9 g approx. 1,000 g approx. Type Min. sensing object ø25 mm ø0.984 in type (20 mm in beam pitch) Pigtailed type H8J05 H12J05 H16J05 H20J05 H24J05 H28J05 H32J05 Item Cable type H8 H12 H16 H20 H24 H28 H32 No. of beam channels Protective height 160 mm in 240 mm in 320 mm in 400 mm in 480 mm in 560 mm in 640 mm in Current consumption Designation Appearance Model No. Handycontroller Cable set for cable type connection F H Model No. multipurpose lights off multipurpose lights up Emitter: 70 ma or less Receiver: 85 ma or less Emitter: 120 ma or less Receiver: 135 ma or less Emitter: 70 ma or less Receiver: 90 ma or less Emitter: 120 ma or less Receiver: 140 ma or less Emitter: 75 ma or less Receiver: 95 ma or less Emitter: 120 ma or less Receiver: 145 ma or less Emitter: 80 ma or less Receiver: 100 ma or less Emitter: 120 ma or less Receiver: 150 ma or less PFHd* MTTFd* 100 years or more Net weight Total of emitter and receiver Pigtailed type Fixed blanking Code Floating blanking Auxiliary output emission FUNCTION Protect Copy CANCEL ENTER Monitor SFCHC SFCWNC1 Pigtailed type Cable type Cable set Synchronization Synchronization + 8core Mating cable 240 g approx. 0 g approx. 360 g approx. 420 g approx. 490 g approx. 550 g approx. 610 g approx. Cable type 6 g approx. 700 g approx. 760 g approx. 820 g approx. 880 g approx. 950 g approx. 1,000 g approx. * PFHd: Probability of dangerous failure per hour. MTTFd: Mean time to dangerous failure. +V 0 V circuit Terminal block Handycontroller Not used 8core circuit Handycontroller
12 Ultraslim Curtain Type 4 SERIES 542 SPECIFICATIONS curtain common specifications Type Pigtailed type Cable type Item Model No. F J05 H J05 F H Applicable standards International standard IEC /2 (Type 4), ISO (Category 4, PLe), IEC to 7 (SIL 3) Japan JIS B 97041/2 (Type 4), JIS B (Category 4), JIS C 0508 (SIL 3) Europe (EU) (Note 2) EN (Type 4), EN ISO (Category 4, PL e), EN to 7 (SIL 3), EN 55011, EN 50178, EN North America (Note 3) Operating range (Note 4) ANSI/UL /2 (Type 4), ANSI/UL 508, UL 1998 (Class 2), CAN/CSA /2 (Type 4), CAN/CSA C22.2 No.14, OSHA , OSHA (C), ANSI B11.1 to B11.19, ANSI/RIA to 3 m to ft Beam pitch 10 mm in 20 mm in 10 mm in 20 mm in Min. sensing object (Note 5) ø14 mm ø0.551 in opaque object ø25 mm ø0.984 in opaque object ø14 mm ø0.551 in opaque object ø25 mm ø0.984 in opaque object Effective aperture angle ±2.5 or less [for an operating range exceeding 3 m ft (conforming to IEC / UL )] Supply voltage 24 V DC % Ripple PP 10 % or less outputs (OSSD 1, OSSD 2) PNP opencollector transistor / NPN opencollector transistor (switching method) <When selecting PNP output> <When selecting NPN output> Max. source current: 200 ma Max. sink current: 200 ma Applied voltage: same as supply voltage (between the control output and +V) Applied voltage: same as supply voltage (between the control output and 0 V) Residual voltage: 2.5 V or less (source current 200 ma, Residual voltage: 2.5 V or less (sink current 200 ma, when when using 10 m ft length cable) using 10 m ft length cable) Leakage current: 200 µa or less (including power supply OFF condition) Leakage current: 200 µa or less (including power supply OFF condition) Max. load capacity: 1 µf (No load to Max. source current) Max. load capacity: 1 µf (No load to Max. sink current) Load wiring resistance: 3 Ω or less Load wiring resistance: 3 Ω or less Operation mode ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the light curtain or the synchronization signal)(note 6,7) Protection circuit Incorporated Response time OFF response: 9 ms or less, ON response: 90 ms or less OFF response: 7 ms or less, ON response: 90 ms or less OFF response: 9 ms or less, ON response: 90 ms or less OFF response: 7 ms or less, ON response: 90 ms or less PNP opencollector transistor / NPN opencollector transistor (switching method) Auxiliary output (Nonsafety output) <When selecting PNP output> <When selecting NPN output> Max. source current: 100 ma Max. sink current: 100 ma Applied voltage: same as supply voltage(between the auxiliary source and +V) Applied voltage: same as supply voltage(between the auxiliary sink and 0 V) Residual voltage: 2.5 V or less Residual voltage: 2.5 V or less (source current 100 ma, when using 10 m ft length cable) (sink current 100 ma, when using 10 m ft length cable) Operation mode OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the handycontroller SFCHC). Protection circuit Incorporated ELCA function Incorporated (reducing mutual interference automatically) Test / reset input function Incorporated Interlock function Incorporated [Manual reset / Automatic reset (Note 8)] External device monitoring function Incorporated input function Incorporated (safety contact) Muting function / Override function Incorporated Optional functions (Note 9) Fixed blanking, floating blanking, auxiliary output change, safety input (safety sensor), large multipurpose setting change, interlock setting change, external relay monitoring setting change, muting setting change, override setting change, protecting Pollution degree 3 Operating altitude 2,000 m 6, ft or less (Note 10) Degree of protection IP67 / IP65 (IEC) Ambient temperature 10 to +55 C +14 to +131 F (No dew condensation or icing allowed), Storage: 25 to +60 C 13 to +140 F Ambient humidity to 85 % RH, Storage: to 85 % RH Ambient illuminance Incandescent light: 5,000 lx or less at the lightreceiving face Dielectric strength voltage 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 55 Hz frequency, 0.75 mm 0.0 in amplitude in X, Y and Z directions for two hours each Shock resistance 0 m/s 2 acceleration ( G approx.) in X, Y and Z directions for three times each Emitting element Infrared LED (Peak emission wavelength: 855 nm mil) Material Enclosure: Polycarbonate alloy, Sensing surface: Polycarbonate alloy Cable 0.15 mm 2 12core heatresistant PVC cable, 0.5 m ft long with connector 0.15 mm 2 12core heatresistant PVC cable, 5 m ft long Cable extension Extension up to 40.5 m ft is possible for both emitter and receiver, with 0.2 mm 2 or more cable. (Note 11) Environmental resistance Accessories MSSFC1 (Standard mounting bracket): 1 set, TR14 (Test rod): 1 No. MSSFC1 (Standard mounting bracket): 1 set, TR25 (Test rod): 1 No. MSSFC1 (Standard mounting bracket): 1 set, TR14 (Test rod): 1 No. MSSFC1 (Standard mounting bracket): 1 set, TR25 (Test rod): 1 No. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 C +68 F. 2) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate. 3) With regards to the standards in the US, under the US regulation 29 CFR , TÜV SÜD, a Nationally Recognized Testing Laboratory (NRTL) certified by OSHA, has certified with the safety certificate based on UL / ANSI standards. With regards to the standards in Canada, under the safety regulations based on CEC (Canadian Electric Code), TÜV SÜD, a Certification Body accredited by SCC, has certified with the safety certificate based on CSA standards. 4) The operating range is the possible setting distance between the emitter and the receiver. The light curtain can detect an object less than 0.1 m ft away. 5) When the floating blanking function is used, the size of the min. sensing object is changed. 6) The outputs are not OFF when muting function is active even if the beam channel is interruped. 7) In case the blanking function is valid, the operation mode is changed. 8) The manual reset and automatic reset are possible to be switched depending on the wiring status. 9) In case of using optional function, the handycontroller SFCHC (optional) is required. 10) Do not use or store the device in an environment where the air pressure is higher than the atmospheric pressure at an altitude of 0 meters. 11) When the muting lamp is used, the cable can be extended within.5 m ft (for emitter / receiver). PHOTO PHOTO MEASURE ITY
13 543 Ultraslim Curtain Type 4 SERIES PHOTO PHOTO MEASURE ITY Item Model No. SFCHC Supply voltage 24 V DC % Ripple PP 10 % or less (common to light curtain power supply) Current consumption 65 ma or less Communication method Digital display Function s Functions Environmental resistance Cable Weight SPECIFICATIONS unit Item Connectable light curtains Applicable standards category Handycontroller RS485 twoway communications (Specific procedure) 4digit red LED display 2 (Selected beam channels, setting contents etc. are displayed.) Green LED 9 (Set function is displayed.) Fixed blanking / Floating blanking / Auxiliary output change / Satety input setting change / multipurpose setting change / Muting setting change / Interlock setting change / External device monitoring setting change / Override setting changing function 60 sec. / Protecting Ambient temperature 10 to +55 C +14 to +131 F (No dew condensation or icing allowed), Storage: 25 to +70 C 13 to +158 F Ambient humidity Voltage withstandability Insulation resistance Model No. Supply voltage / Current consumption Fuse (power supply) SFC13 curtain manufactured by Panasonic Industrial Devices SUNX EN (Type 4), EN 55011, EN ISO (Category 4, PLe), IEC (Type 4), ISO (Category 4, PLe), JIS B (Type 4), JIS B (Category 4), ANSI/UL (Type 4), UL 1998 (Class 2) ISO (JIS B 97051) compliance up to Category 4, PL e standards 24 V DC ± 10 % Ripple PP 10 % or less / 100 ma or less (without light curtain) Builtin electronic fuse, Triggering current: 0.5 A or more, Reset after power down Enabling path NO contact 3 (1314, 2324, 3334) Application category AC15, DC13 (IEC ) Rated operation voltage (Ue) / Rated operation current (le) Contact resistance Contact protection fuse rated Pickup delay (Auto reset / Manual reset) Response time (Recovery time) Auxiliary output Rated operation voltage / current Contact protection fuse rated Semiconductor auxiliary output (AUX) Output operation Excess voltage category Polarity selection function V DC / 4 A, 2 V AC / 4 A, resistive load (For inductive load, during contact protection). Min applicable load: 10 ma (at 24 V DC) (Note 2) 100 mω or less (initial value) 4 A (slow blow) 80 ms or less / 90 ms or less 10 ms or less relay contact (NC contact) 1 (4142) (Related to enabling path) 24 V DC / 2 A, Min. applicable load: 10 ma (at 24 V DC) 2 A (slow blow) PNP opencollector transistor Max. source current: 60 ma On when the light curtain is interrupted Pollution degree 2 Environmental resistance Protection to 85 % RH, Storage: to 85 % RH 1,000 V AC for one min. between all supply terminals connected together and enclosure 20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure 12core shielded cable, 0.5 m ft long, with a connector at the end (2 cables) Net weight: 200 g approx. Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 C +68 F. II Incorporated (Cable connection allows selection of plus / minus ground) Minus ground: Correspond to PNP output light curtain Plus ground: Correspond to NPN output light curtain Enclosure: IP40, Terminal IP20 Ambient temperature 10 to +55 C +14 to +131 F (No dew condensation or icing allowed), Storage: 25 to +70 C 13 to +158 F Ambient humidity Vibration resistance Enclosure material Weight to 85 % RH, Storage: to 95 % RH Resistance / malfunction 10 to 55 Hz frequency, 0.35 mm in amplitude in X, Y, and Z directions for twenty times each ABS Net weight: 200 g approx. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 C +68 F 2) If several SFC13 units are being used in line together, leave a space of 5 mm in or more between each unit. If the units are touching each other, reduce the rated operating current for safety output in accordance with the ambient operating temperature as shown in the graphs at right. 3) Refer to our website for details of specifications. Dilating when SFC13 units are mounted close together Rated operation current (A) Ambient temperature ( C F)
14 Ultraslim Curtain Type 4 SERIES 544 I/O CIRCUIT AND WIRING DIAGRAMS I/O circuit diagram <In case of using I/O circuit for PNP output> Emitter Sensor circuit Sensor circuit 0.47 μf 0.47 μf Receiver 0.1 μf 0.1 μf 0.1 μf 0.1 μf * S1, S2 Terminal No. of pigtailed type Color code (Brown) +V (Pink) Test input / Reset input (Pale purple) Interlock setting input (Red) Muting lamp output (Shield) Output polarity setting wire (Blue) 0 V (Orange) Synchronization + (Orange / Black) Synchronization *S μf (Yellow) Override input Internal circuit 47 kω 3 kω 3 kω 47 kω 47 kω 0.47 μf 47 kω Internal circuit (Gray) input 1 (Gray / Black) input 2 (Yellowgreen / Black) Auxiliary output Users circuit (Orange / Black) Synchronization (Orange) Synchronization + (Brown) +V (Gray) multipurpose input 1 (Gray / Black) multipurpose input 2 (Skyblue / White) Muting input 1 (Skyblue / Black) Muting input 2 (Shield) Output polarity setting wire (Blue) 0 V Load (Yellowgreen) External device monitoring input (Black) output 1 (OSSD 1) (White) output 2 (OSSD 2) + K1 K2 24 V DC % K1, K2: External device (Forceguided relay or magnet contactor) Users circuit S1 Test input / Reset input For manual reset Vs to Vs 3.5 V (sink current 5 ma or less): OFF (Note) : ON For automatic reset Vs to Vs 3.5 V (sink current 5 ma or less): ON (Note) : OFF S2 Interlock setting input, Override input, Muting input 1 / 2, multipurpose input 1 / 2, Vs to Vs 3.5 V (sink current 5 ma or less): Valid (Note) : Invalid Note: Vs is the applying supply voltage. K2 K1 I/O circuit diagram <In case of using I/O circuit for NPN output> Emitter Sensor circuit 3 kω (Red) Muting lamp output (Gray) input 1 (Gray / Black) input 2 *S1 (Pink) Test input / Reset input 0.47 μf (Pale purple) Interlock setting input 0.47 μf (Yellow) Override input 0.47 μf 0.47 μf 47 kω 0.1 μf 0.1 μf 0.1 μf Internal circuit Receiver Sensor circuit * S1, S2 47 kω 47 kω 3 kω (Blue) 0 V (Orange) Synchronization + (Orange / Black) Synchronization (Orange / Black) Synchronization (Orange) Synchronization + (Brown) +V (Shield) Output polarity setting wire (Gray) multipurpose input μf 47 kω (Gray / Black) multipurpose input 2 Internal circuit Terminal No. of pigtailed type Color code (Brown) +V (Shield) Output polarity setting wire Load (Yellowgreen / Black) Auxiliary output Users circuit (Black) output 1 (OSSD 1) (White) output 2 (OSSD 2) (Yellowgreen) External device monitoring input (Skyblue / White) Muting input 1 (Skyblue / Black) Muting input 2 (Blue) 0 V Users circuit S1 Test input / Reset input For manual reset 0 to +2.5 V (source current 5 ma or less): OFF : ON For automatic reset 0 to +2.5 V (source current 5 ma or less): OFF : ON K1 + K2 24 V DC % K1 K2 K1, K2:External device (Forceguided relay or magnet contactor) S2 Interlock setting input, Override input, Muting input 1 / 2, multipurpose input 1 / 2, 0 to +2.5 V (source current 5 ma or less): Valid : Invalid PHOTO PHOTO MEASURE ITY
15 545 Ultraslim Curtain Type 4 SERIES PHOTO PHOTO MEASURE ITY I/O CIRCUIT AND WIRING DIAGRAMS Connection example Basic wiring: Min. operation only This is the general configuration using one set of the emitter and receiver facing each other. The control outputs (OSSD 1 / OSSD 2) turn OFF if the light is interrupted, while they automatically turn ON if receive the light. The auxiliary output is used to invalid the external device monitoring function. The auxiliary output cannot be connected to external devices. <In case of using I/O circuit for PNP output> (Red) Muting lamp output Receiver Emitter (Yellow) Override input (Pale purple) Interlock setting input (Brown) +V (Pink) Test input / Reset input (Gray) input 1 (Gray / Black) input 2 (Shield) Output polarity setting wire (Blue) 0 V (Yellowgreen / Black) Auxiliary output (Orange) Synchronization + (Orange / Black) Synchronization (Orange / Black) Synchronization (Orange) Synchronization + Gray cable (Yellowgreen) External device monitoring input Gray cable (with black line) (Brown) +V (Black) output 1 (OSSD 1) K1 (White) output 2 (OSSD 2) K2 (Shield) Output polarity setting wire (Blue) 0 V (Skyblue / White) Muting input 1 (Skyblue / Black) Muting input 2 (Gray) multipurpose input 1 (Gray / Black) multipurpose input 2 K1, K2: Forceguided relay or magnet contactor Interlock function External device monitoring function Auxiliary output Output polarity setting wire input + 24 V DC % Disabled (Automatic reset) Disabled Not used PNP Invalid PRECAUTIONS FOR PROPER When this light curtain is used in the PSDI mode, an appropriate control circuit must be configured between this light curtain and the machinery. For details, be sure to refer to the standards or regulations applicable in each region or country. This catalog is a guide to select a suitable product. Be sure to read instruction manual attached to the product prior to its use. Both emitter and receiver are adjusted in combination at factory setting, please apply both emitter and receiver with the same serial No. The serial No. is indicated on the plates of both emitter and receiver. (Indicated under model No.) Make sure to carry out the test run before regular operation. Do not install this light curtain with a machine whose operation cannot be stopped immediately in the middle of an operation cycle by an emergency stop equipment. Others Do not use during the initial transient time (2 sec.) after the power supply is switched on. Avoid dust, dirt and steam. Take care that the sensor does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. Take care that the sensor is not directly exposed to fluorescent lamp from a rapidstarter lamp or a high frequency lighting device, as it may affect the sensing performance. <In case of using I/O circuit for NPN output> Receiver Gray cable Emitter Gray cable (with black line) Handycontroller (Red) Muting lamp output (Yellow) Override input (Pale purple) Interlock setting input (Brown) +V (Shield) Output polarity setting wire (Gray) input 1 + (Gray / Black) input 2 (Pink) Test input / Reset input (Blue) 0 V (Yellowgreen / Black) Auxiliary output (Orange) Synchronization + (Orange / Black) Synchronization (Orange / Black) Synchronization (Orange) Synchronization + (Yellowgreen) External device monitoring input (Brown) +V (Black) output 1 (OSSD 1) K1 (White) output 2 (OSSD 2) K2 (Shield) Output polarity setting wire (Blue) 0 V (Skyblue / White) Muting input 1 (Skyblue / Black) Muting input 2 (Gray) multipurpose input 1 (Gray / Black) multipurpose input 2 K1, K2: Forceguided relay or magnet contactor Interlock function External device monitoring function Auxiliary output Output polarity setting wire input 24 V DC % Disabled (Automatic reset) Disabled Not used NPN Invalid Refer to the instruction manual for details. The instruction manual can be downloaded from our website. This light curtain enables to set each function using the handycontroller SFCHC. Among the functions, the contents related to the safety distance such as the size of the minimum sensing object and response time are varied depending on the setting condition. When setting each function, recalculate the safety distance, and make enough space larger than the calculated safety distance. Failure to do so might cause the accident that the device cannot stop quickly before reaching the dangerous area of the machinery, resulting in the serious injury or death. Refer to the instruction manual enclosed with the handycontroller for details of the function settings for using handycontroller SFCHC (optional).
16 Ultraslim Curtain Type 4 SERIES 546 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. F H Mounting bracket assembly dimensions Mounting drawing for the light curtains using the standard mounting brackets MSSFC1 (accessory). <Center mounting> <Dead zoneless mounting> D C B A Beam pitch F Display section (Note) ( 0.827) 50.5 ( 1.988) 88 ( 3.465) Multipurpose t 2 t ( 3.465) Multipurpose G t 2 t D C B A F Display section (Note) ( 0.827) 50.5 ( 1.988) 88 ( 3.465) Multipurpose ( 3.465) Multipurpose G E Display section (Note) Multipurpose 18 ( 0.709) 88 ( 3.465) Beam pitch 7.7 ( 0.3) ( 0.827) 50.5 ( 1.988) A B t 2 t ( 3.465) Multipurpose B A Beam pitch Display section (Note) E Multipurpose Emitter Receiver Emitter Receiver F G 18 ( 0.709) ( 1.988) 88 ( 3.465) F ( 0.3) curtain t 2 t ( 3.465) Multipurpose G PHOTO PHOTO MEASURE ITY Model No. A B C D E F15(J05) H8(J05) F23(J05) H12(J05) F31(J05) H16(J05) F39(J05) H20(J05) F47(J05) H24(J05) F55(J05) H28(J05) F63(J05) H32(J05) Model No. F G F ø5 H ø0.197 Connector of the pigtailed type J05 ø6 ø ( 1.772) ø15.6 ø0.614 Note: Measurement of drawing above is display section of H. In case of F, the position of digital (red) is different as right figure.also, digital (red) is not incorporated in F15. <H > <F > Digital error
17 547 Ultraslim Curtain Type 4 SERIES DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. PHOTO PHOTO MEASURE ITY F H Mounting bracket assembly dimensions curtain Mounting drawing for the light curtains using the versatile brackets MSSFCC3 (optional) and intermediate supporting bracket for versatile brackets MSSFCF4 (optional). <Rear mounting> B ( 0.591) MSSFC ( 0.591) D AC Multipurpose Multipurpose Model No Multipurpose B ( 0.591) 7.5 ( 0.295) MSSFC3 Multipurpose MSSFC B ( ) MSSFC3 MSSFC4 MSSFC4 MSSFC4 6.5 D A C D A D A MSSFC Inter mediate supporting bracket F15(J05) H8(J05) F23(J05) H12(J05) F31(J05) H16(J05) F39(J05) H20(J05) F47(J05) H24(J05) F55(J05) H28(J05) Available F63(J05) H32(J05) Available Multipurpose Multipurpose ( ) ( ) Multipurpose A A' B B' C D <Dead zoneless mounting> 238 to to to to to to to to Multipurpose Emitter Receiver Emitter Receiver Note: Be sure to mount MSSFC4 when using F55(J05)/F63(J05)/H28(J05)/H32(J05). B ( )
18 Ultraslim Curtain Type 4 SERIES 548 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. MSSFC1 Standard mounting bracket (Accessory) t 2 t Mounting hole for M3 countersunk screw (for main body mounting) Material: Stainless steel (SUS4) Net weight: 32 g approx. (4 pcs.) Package weight: 35 g appox. Four bracket set Four M3 (length 4 mm in) countersunk screws are attached MSSFC2 NA2N compatible mounting bracket (Optional) t 2 t ø4.5 ø Mounting hole for M3 countersunk screw (for main body mounting) Material: Stainless steel (SUS4) Net weight: 36 g approx. (4 pcs.) Package weight: 40 g appox. Four bracket set Four M3 (length 4 mm in) countersunk screws are attached PHOTO PHOTO MSSFC3 <Rear mounting> <Dead zoneless mounting> Versatile bracket (Optional) MEASURE ITY 2ø4.5 ø Material: Stainless steel (SUS4) Net weight: 75 g approx. (4 pcs.) Package weight: 90 g appox. Four bracket set Four M3 (length 4 mm in) countersunk screws are attached ( 0.118) M3 countersunk screw mounting hole (for main body mounting) t1.5 t t2 t0.079 ( ) ( ) ( ) M3 countersunk screw mounting hole (for main body mounting) ( ) ø4.5 ø t2 t0.079 t1.5 t0.059 MSSFC Intermediate supporting bracket for versatile bracket (Optional) 13.6 ( 0.535) ( ) t2 t Material: Stainless steel (SUS4) Net weight: 40 g approx. (2 pcs.) Package weight: 60 g appox. Two bracket set ( )
19 549 Ultraslim Curtain Type 4 SERIES DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. PHOTO PHOTO MEASURE ITY MSSFCH ø6.4 ø0.252 (M6 mounting hole) (When using MSSFC2) ø5.4 ø0.3 (M5 mounting hole) (When using MSSFC1) F ø5.4 ø0.3 (M5 mounting hole) (When using MSSFC1) ø6.4 ø0.252 (M6 mounting hole) (When using MSSFC2) t2.3 t E D C B A ø4.8 ø0.189 (M4 mounting hole) (When using MSSFC2) Assembly dimensions Metal protection case (Optional) Mounting drawing for the light curtains using the metal protection case (MSSFCH ). Display section D A ø5.4 ø0.3 (M5 mounting hole) (When using MSSFC1) ø5.4 ø0.3 (M5 mounting hole) (When using MSSFC1) Model No. A B C D E F Net weight (2 pcs.) MSSFCH8 MSSFCH12 MSSFCH16 MSSFCH20 MSSFCH24 MSSFCH28 MSSFCH g approx. 240 g approx. 340 g approx. 420 g approx. 520 g approx. 600 g approx. 700 g approx.
20 Ultraslim Curtain Type 4 SERIES 550 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. SFBCC MU SFCWY1 ø9 ø0.354 ø15.6 ø ( 1.772) ø14 ø0.551 Mating cable with connector on one end (Optional) L ø6 ø0.236 Length L Model No. Length L SFBCC3MU 3, SFBCC7MU 7, SFBCC10MU 10, Yshaped connector (Optional) SFBCCJ MU ø15.6 ø ( 1.772) WY1CCN3 WY1CCN10 ø14 ø0.551 Mating cable with connectors on both ends (Optional) L ( 1.772) ø6 ø0.236 Length L Model No. SFBCCJ3DMU SFBCCJ3EMU ø15.6 ø0.614 Length L 3, SFBCCJ10DMU 10, SFBCCJ10EMU L Mating cable (Optional) ø6 ø0.236 Model No. Length L WY1CCN3 3, WY1CCN10 10, PHOTO PHOTO MEASURE ITY SFCHC Handycontroller (Optional) ø6 ø0.236 cables, 0.5 m ft long SFC unit (Optional) = = FUNCTION CANCEL ENTER Suitable for 35 mm in width DIN rail Introduction to Panasonic Industrial Devices SUNX sensors that can be used as muting sensors Compact Photoelectric Sensor CX400 SERIES ver.2 World standard size Wide variation Ultraslim Photoelectric Sensor EX10 SERIES ver mm in thickness Long sensing range: 1 m ft (thrubeam type: EX19) * The EX20 series that is compatible with M3 mounting screws is also available. Ushaped Micro Photoelectric Sensor PM64 SERIES Extremely compact and space saving A lineup of quick fittingup connector type P.277~ P.313~ P.429~ P.807~ Rectangularshaped Inductive Proximity Sensor GXF/H SERIES Industry longest in stable sensing range 10 times the durability (Compared to previous models) IP68G protective construction
panasonic.net/id/pidsx/global The control category differs depending on the configuration and wiring of the external circuit.
577 Ultraslim Light Curtain Type 4 SERIES Related Information General terms and conditions... F3 SFC13... P.663~ General precautions... P.1595 guide... P.457~ Glossary of terms... P.1549~ Korea s Smark...
More informationUltra-slim Light Curtain
Ultraslim Type 4 PLe SIL3 LIGHT CURTAIN SF4CSERIES Conforming to Machine & EMC Directive Certified Conforming to OSHA / ANSI Certified by NRTL JIS Machine safeguarding without sacrificing productivity
More informationpanasonic.net/id/pidsx/global The control category differs depending on the configuration and wiring of the external circuit.
631 Ultra-slim Light Curtain Type 2 SERIES Related Information General terms and conditions... -3 Glossary of terms / General precautions...p.1549~ / P.1595 guide...p.457~ S-C13... P.663~ PHOTO PHOTO Certified
More informationBuilding method. Exclusive mating cable for SF-C14EX(-01) SF4B series Muting sensor. Less wiring!
Exclusive Control Unit for Light Curtain SERIES Related Information General terms and conditions... F- SFB / SFB-G... P.0~ General precautions... P.9 SFD... P.9~ SFC / SFB...P.77~ / P.0~ Korea s S-mark...
More informationType 4. Depth
499 Compact Curtain Type 4 SERIES Related Information General terms and conditions... F-7 SF-C10... P.703~ General precautions... P.1458~ Sensor selection guide... P.497~ Glossary of terms... P.1455~ Korea
More informationSF-C10 SERIES. Exclusive Control Unit for Light Curtain. Plug-in type control unit. Robust type control unit SF-C12 Slim type control unit SF-C13
Exclusive Unit for Curtain SERIES PHOTO PHOTO MEASURE Conforming to Machine, Low Voltage (SF-C/C only) & EMC Directive Certified Listing Less setup time for safety circuits Plug-in type control unit SF-C
More informationpanasonic.net/id/pidsx/global The control category differs depending on the configuration and wiring of the external circuit.
545 Compact Curtain Type 4 SERIES Related Information General terms and conditions... F-3 SF-C13... P.663~ General precautions... P.1595 guide... P.457~ Glossary of terms... P.1549~ Korea s S-mark... P.1602
More informationMonitor. Safety relay,etc. Contactor, etc. Uses external device monitoring function Note: Construct a separate reset input circuit.
Selectable safety circuits The light curtain unit has a built-in monitoring function for external devices (such as fused relay monitoring). This supports the construction of light curtain peripheral safety
More informationpanasonic.net/id/pidsx/global The control category differs depending on the configuration and wiring of the external circuit.
675 Compact Beam Sensor Type 4 SERIES Related Information General terms and conditions... F-3 General precautions... P.1595 PHOTO PHOTO Certified Listing Conforming to OSHA / ANSI MEASURE Category 4 PLe
More informationBoth Compact and Robust. Safety Light Curtain SF4D SERIES. New Concept. GB Conforming to Compact & Robust panasonic.net/id/pidsx/global
Compact & Robust Type4 PLe SIL3 Safety Light Curtain SF4D SERIES Conforming to OSHA / ANSI Certified GB Conforming to 4584 NRTL certified Certified (Excluding SF4D- -01) New Concept Both Compact and Robust
More informationPM-24 SERIES. Ultra-small U-shaped Micro Photoelectric Sensor. Extremely small size enables space saving!! ( ) Equipped with two independent outputs
19 Ultra-small Micro Photoelectric Sensor PM- SERIES Related Information General terms and conditions...p.1 Glossary of terms / General precautions...p.98~ / P.98~ Amplifier Built-in Sensor selection guide...p.11~
More informationSALES NUMBER NUMBER OF BEAMS PROTECTIVE HEIGHT
SECTION 21 182 Safety Light Curtains Type: SLC-F Finger (14mm) FEATURES: Resolution: 14mm Protective height: 160mm to 1040mm Type 4 according to IEC61496-1 and -2 ORDERING INFORMATION: SALES OF BEAMS PROTECTIVE
More informationUltra-small U-shaped Micro Photoelectric Sensor. Extremely small size enables space saving!! 12 mm in
1 Ultra-small Micro Photoelectric PM- SERIES Related Information General terms and conditions... F-17 Glossary of terms / General precautions... P.19~ / P.10 Amplifier Built-in selection guide... P.1~
More informationOne step ahead in performance and mounting ease
95 Micro Photoelectric Amplifier Built-in PM-5 SERIES PM-45 SERIES PM-5 SERIES General terms and conditions... F- guide... P.9~ Related Information Glossary of terms / General precautions...p.1549~ / P.155~
More informationOptimum sensing capability for LCD manufacturing
SENSORS FOR Glass Substrate Detection Sensor Amplifier-separated FX-301-F FT-F9 FD-F7 EX-F70/F60 HD-T1 M FD-L3 Reliable detection of glass substrates Its unique optical system enables detection of transparent
More informationNA1-5. Ultra-slim Body 25mm Beam Pitch Area Sensor. Even a Slim Hand Is Detected by the 25mm Pitch Beam Curtain AREA SENSORS.
Ultra-slim Body 2mm Pitch Area Sensor mm Thick: /2 of Conventional Model It fits into a small space, without obstructing normal operation. Clearly Visible Job Indicator Both the emitter and the receiver
More informationSF4C. Instruction Manual
safety LIGHT CURTAIN SF4C Instruction Manual BEFORE BEGINNING The printed English and Japanese versions of this instruction manual are the original versions. The English, French, German, Italian and Spanish
More informationRemote I/O Unit with Connectors for Light Curtain CC-Link Safety System. panasonic.net/id/pidsx/global
715 LIGHT CURTAINS / USE Remote I/O Unit with Connectors for Light Curtain CC-Link System General terms and conditions... F-7 Related Information... P.703~ SF4B... P.565~ General precautions... P.1501
More informationThe World s in Compactness. * Among photoelectric sensors with built-in amplifier, as of June 2015 (survey by our company)
Amplifier Built-in Ultra-minute Photoelectric Sensor EX-Z SERIES Conforming to EMC Directive Recognition No. 1 The World s in Compactness * Among photoelectric sensors with built-in amplifier, as of June
More informationNo. 1. The World s in Compactness. Amplifier Built-in Ultra-minute Photoelectric Sensor EX-Z SERIES panasonic.net/id/pidsx/global
Ultra-minute Photoelectric Sensor EX-Z SERIES Conforming to EMC Directive No. 1 The World s in Compactness * Among photoelectric sensors with built-in amplifier, as of June 215 (survey by our company)
More informationConnector Built-in U-shaped Micro Photoelectric Sensor. Approximately 60 % of previous model Detachable
44 Connector Built-in Micro Photoelectric SERIES Related Information General terms and conditions... F-1 Glossary of terms... P.1~ selection guide... P.441~ General precautions... P.140 Amplifier Built-in
More informationUltra-slim Body Picking Sensor NA1-PK5 SERIES NA1-5 SERIES. Even a slim hand is detectable by the 25 mm in pitch beam area sensor
487 FIBER PHOTO MICRO PHOTO AREA IGHT CURTAINS PRESSURE / FOW INDUCTIVE PROXIMITY PARTICUAR USE SENSOR SIMPE UNITS MEASUREMENT STATIC CONTRO DEVICES ENDOSCOPE MARKERS Ultra-slim Body Picking Sensor NA-PK5
More informationSuitable for detecting transparent films or transparent bottles
Ultrasonic Sensor Suitable for detecting transparent films or transparent bottles Reliable detection of transparent objects The sensor reliably detects transparent films or transparent objects. Only 16
More informationPM2 SERIES. Convergent Reflective Micro Photoelectric Sensor. Convergent reflection sensing ensures stable detection
3 Micro Photoelectric PM SERIES Related Information General terms and conditions... F-3 Glossary of terms... P.~ Amplifier Built-in selection guide... P.7~ General precautions... P.8~ PHOTO PHOTO Conforming
More informationEF-S1 SERIES. Continuously check invisible static electricity in lines. Constantly check static in lines!
1215 PHOTO PHOTO SAFETY USE SERIES Related Information General terms and conditions... F- General precautions... P.1595 guide... P.1155~ MEASUREMENT panasonic.net/id/pidsx/global Continuously check invisible
More informationSEN TRONIC AG WARNING. QUICK INSTRUCTION MANUAL Compact Light Curtain / Type 4 SF4B- C 1 SAFETY PRECAUTIONS 2 CONFIRMATION OF PACKED CONTENTS
QUICK INSTRUCTION MANUAL Compact Light Curtain / Type 4 SF4B- C ME-SF4BC No.0053-27V Thank you very much for purchasing Panasonic products. Read this Instruction Manual carefully and thoroughly for the
More informationPM2 SERIES. Convergent Reflective Micro Photoelectric Sensor. Convergent reflection sensing ensures stable detection
PHOTO PHOTO Micro Photoelectric PM SERIES Related Information General terms and conditions... F-3 Glossary of terms... P.9~ Amplifier Built-in guide... P.393~ General precautions... P.~ Certified MEASURE
More informationSERIES. FX-311 realizes the ultimate in ease-of-operation. Its operation enables easy and full use of latest technology.
FX-11 SERIES FX-11 realizes the ultimate in ease-of-operation. Its operation enables easy and full use of latest technology. Presenting a product which satisfies professionals using volume control. Besides
More informationE3S-A. Built-in Amplifier Photoelectric Sensor (Medium Size) Ordering Information. Built-in Amplifier Photoelectric Sensors. Horizontal. 7 m.
Built-in Amplifier (Medium Size) ES-A Be sure to read Safety Precautions on page 0. Ordering Information Built-in Amplifier s Red light Infrared light Sensing method Appearance Connection method Sensing
More informationGL SERIES. Compact & Low Price Inductive Proximity Sensor. Wide variety, high performance in surprisingly small body at low cost.
811 Compact & ow Price Inductive Proximity Sensor SERIES Related Information General terms and conditions... F-3 Glossary of terms...p.176~ guide... P.781~ General precautions... P.179~ PHOTO PHOTO MEASURE
More informationPlug-in unit extension block One sensor extension block allows four plug-in units to be added. Power cable for sensors. Snap-connector inputs
1 Sensor Block for SC Quick connection of 16 sensors Set of 16 inputs directly hooked up to PLC Up to 16 sensors can be connected on one main block followed by three extension blocks (or one snapconnector
More informationPM2 SERIES. Convergent Reflective Micro Photoelectric Sensor. Convergent reflection sensing ensures stable detection
3 Micro Photoelectric PM SERIES Related Information General terms and conditions...p. Glossary of terms...p.983~ selection guide...p.~ / P.9~ General precautions...p.98~ Amplifier Built-in PHOTO PHOTO
More informationGA-311 GH SERIES. Compact Inductive Proximity Sensor Amplifier-separated. High-speed response and excellent workability
82 PHOTO PHOTO Compact Inductive Proximity Sensor -separated GA- SERIES General terms and conditions... F-7 Related Information Glossary of terms... P.86~ Sensor selection guide... P.757~ General precautions...
More informationpanasonic.net/id/pidsx/global CCD The sensor can be used for various applications with its binary data output with four different sensing modes.
1123 PHOTO PHOTO PARTICUR Type Edge Sensor SERIES Related Information General terms and conditions... F-3 About laser beam... P.1593~ guide... P.1021~ General precautions... P.1595 Conforming to FDA regulations
More informationThe dual display means that the current value and the threshold value, it makes direct setting of threshold value
735 Dual Display Digital Pressure Sensor DPC-L100 SERIES SERIES General terms and conditions... F-3 guide... P.699~ Related Information Glossary of terms... P.1563~ General precautions... P.1566 For Liquid
More informationAdjustable Range Reflective Photoelectric Sensor Amplifier Built-in
36 FIBER PHOTO MICRO PHOTO AREA LIGHT CURTAINS PRESSURE / FLOW INUCTIVE PROXIMITY PARTICULAR USE SENSOR SIMPLE UNITS MEASUREMENT STATIC CONTROL EVICES ENOSCOPE MARKERS Adjustable Range Reflective Photoelectric
More informationGA-311 GH SERIES. Compact Inductive Proximity Sensor Amplifier-separated. High-speed response and excellent workability. IP67G sensor head variations
875 PHOTO PHOTO IT FOW PARTICUAR Compact Inductive Proximity Sensor -separated GA- SERIES General terms and conditions... F-7 Related Information Glossary of terms... P.482~ Sensor selection guide... P.80~
More informationInstruction Manual SF4B- C. Compact Light Curtain / Type 4. Phone: Fax: Web: -
Compact Light Curtain / Type 4 SF4B- C Instruction Manual WUME-SF4BC-7 (MEMO) 2 Panasonic Industrial Devices SUNX Co., Ltd. 2016 Thank you for purchasing Panasonic Industrial Devices SUNX s Compact Light
More informationGX SERIES. Cylindrical Compact Inductive Proximity Sensor Amplifier Built-in. Robust enclosure and flexible cable types are also available
8 Cylindrical Compact Inductive Proximity SERIES Related Information General terms and conditions... F-7 Glossary of terms... P.86~ selection guide... P.757~ General precautions... P.05 PHOTO PHOTO Conforming
More informationHead-separated Dual Display Digital Pressure Sensor DPC-L100 SERIES DPH-L100 SERIES. High-precision detection of fluid and air pressure
689 PHOTO PHOTO Dual Display Digital Pressure Sensor DPC-L100 SERIES SERIES General terms and conditions... F-17 Sensor selection guide... P.661~ Related Information Glossary of terms... P.1373~ General
More informationE3S-A. Built-in Amplifier Photoelectric Sensor (Medium Size) Ordering Information. Built-in Amplifier Photoelectric Sensors. Horizontal. 7 m.
Built-in Amplifier (Medium Size) ES-A CSM_ES-A_DS_E Be sure to read Safety Precautions on page 0. Ordering Information Built-in Amplifier s Red light Infrared light Sensing method Appearance Connection
More informationColor Detection Fiber Sensor FZ-10 SERIES. Reliable and precise color discrimination. Red, green and blue LEDs. Easy set up
79 Color Sensor FZ- SERIES FIBER PHOTO MICRO PHOTO AREA LIGHT CURTAINS Related Information General terms and conditions... F-17 Glossary of terms... P.1359~ Sensor selection guide...p.31~ General precautions
More informationCylindrical Compact Inductive Proximity Sensor Amplifier Built-in. panasonic.net/id/pidsx/global
8 PHOTO PHOTO MEASURE Cylindrical Compact Inductive Proximity SERIES Related Information General terms and conditions... F- Glossary of terms... P.576~ panasonic.net/id/pidsx/global guide... P.78~ General
More informationE3FS. Connect up to 4 sets of E3ZS/E3FS per B1 Module for F3SX Safety Controller
Single-beam Safety Sensor Type 2 Safety Photoelectric Sensor for Hazardous Gaps in Machines Note: Be sure to read the Safety Precautions International standards: IEC6496- (type 2 ESPE) IEC6496-2 (type
More informationEX-30SERIES. Threaded Miniature Photoelectric Sensor. The next-generation New Form series. A new alternative to fiber sensors. M4(Reflective type: M6)
EX-3SERIES Threaded Miniature Photoelectric The next-generation New Form series. A new alternative to fiber sensors. Marked Conforming to EMC Directive The EX-3 series have a radically new form which has
More informationMini Photoelectric Sensor
Mini Photoelectric Sensor High cost-performance Mini Photoelectric Sensor Saves Installation Space and Wiring Effort and Detects Minute Sensing Objects Pin-point beam (1 to 2-mm dia.) makes it possible
More informationSafety Control. FS1A Multi-function Safety Relay. Optional Parts. Marked Cable Tie. DIN Rail BNDN1000 Aluminum, 1m 35mm wide
Control Multi-function Relay Key features: No programming required. Configuration complete by turning on a logic switch A safety circuit can be configured easily just by selecting a logic from eight preprogrammed
More informationSafety Control. FS1A Multi-function Safety Relay. Optional Parts. Connecting Tool. Marked Cable Tie. DIN Rail BNDN1000 Aluminum, 1m 35mm wide
Multi-function Relay Key features: No programming required. Configuration complete by turning on a logic switch A safety circuit can be configured easily just by selecting a logic from eight preprogrammed
More informationU-shaped Type/Convergent Reflective Type. onlinecomponents.com
PHOTOELECTRIC SENSOR SERIES U-shaped Type/Convergent Reflective Type SS-A SU-7/SH VF NX MS-AJ RT- PX- EX CY Amplifier-separated Type Multi-voltage Type Amplifier Built-in Type Mounting Stand Stable Detection
More informationF3SL. Safety Light Curtain for Long Distance Detection
Safety Light Curtain for Long Distance Detection CSM DS_E_3_1 20-m long-distance detection. Safety light curtain (Type 4) is ideal for detection of intrusion of human bodies in large machines and conveyor
More informationOS3101. Operator Presence Detection in Work Areas with Complex Shapes. Safety Laser Scanner. Ordering Information. Safety/Area.
Laser Scanner / Operator Presence Detection in Work s with Complex Shapes A Type 3 Laser Scanner in compliance with IEC 61496-1/-3. Two patterns of protective and warning area combinations can be set to
More informationDC 2-wire Cylindrical Inductive Proximity Sensor
SERIES DC -wire Cylindrical Inductive Proximity -wire type available Oil resistant Metal embedding possible Amplifier Built-in GX G-6 High performance & ease of use G-8/8U GA-/GH GX GX-N G-8H/8H G-N Robust
More informationLong sensing range of 500 mm in (HL-T1005A, HL-T1010A) and 2 m ft (HL-T1001A) are available. Adoption of a Class 1 laser
MEASUREMENT SENSORS SERIES Ultra-compact Laser Collimated Beam Sensor LA LA- LM1 LH- HL-C1 The industry s smallest sensor head A high-ality intelligent controller Conforming to EMC Directive The industry
More informationNPN open-collector transistor (Judgment output) Current / voltage output (Linear output)
Ultra-compact Sensor SERIES 144 ORDER GUIDE s Type Appearance Model No. Output NPN output HL-AC1 NPN open-collector transistor (Judgment output) Current / voltage output (Linear output) PNP output HL-AC1P
More informationCompact Inductive Proximity Sensor
SERIES Compact Inductive Proximity Sensor Amplifier Built-in High functionality together with robust housing and flexible cable Miniature is an amplifier built-in inductive proximity sensor having a diameter
More informationUltra-compact Laser Collimated Beam Sensor HL-T1 SERIES. Ultra-compact sensor head A high-functionality intelligent controller
1123 Ultra-compact Sensor SERIES Related Information General terms and conditions... F-7 Glossary of terms / General precautions... P.93 / P.01 Sensor selection guide... P.1055~ About laser beam... P.99~
More informationLight ON 5m. * Light ON. 2.5m (3m) Light ON. (5m)
All voltage photoelectric sensors Built-in amplifier accepts wide supply voltage range. Slim, space-saving construction measures only x x 7.4 mm. s with long life expectancy and high switching capacity
More informationLIGHT SCREENS Catalog Safety Supply Maximum Type Model Page Category Resolution Voltage Range. Page Point Systems. Page 42 4.
Catalog Safety Supply Maximum Type Model Page Category Resolution Voltage Range Standard Systems 14 & 30 mm Cascade Systems Page 20 4 14 & 30 mm 24V dc 18 m Grid & Point Systems 300 to 584 mm (beam spacing)
More informationPM2 SERIES. Convergent Reflective Micro Photoelectric Sensor. Convergent reflection sensing ensures stable detection. Hardly affected by background
PHOTO PHOTO USE MEASUREMENT STATIC CONTROL Micro Photoelectric SERIES Related Information General terms and conditions... F- Glossary of terms... P.39~ selection guide... P.~ General precautions... P.0
More informationConvergent Reflective Micro Photoelectric Sensor
EQ- VF NX PM MS-AJ RT- PX- CY PHOTOELECTRIC SENSORS Mounting Stand Amplifier Built-in SERIES Convergent Reflective Micro Photoelectric Stable detection by convergent reflective mode Stable detection characteristics
More informationMaking Hazardous Operations Safe and Productive
NEW Safety Guard Switching Unit G9SX-GS Making Hazardous Operations Safe and Productive Making Hazardous Operations Safe and Productive This new addition to the model of Flexible Safety Unit G9SX series
More informationOil-resistive, Long-range Photoelectric Sensor with Metal Housing
Oil-resistive, Long-range with Metal Housing ES-C Water- and Oil-resistive with Metal Housing Used for Long-range Sensing Satisfies the water- and oil-resistive requirements and safe enough for use in
More informationThread length (overall length) material
Cylindrical Proximity Sensor for Mobile Usage Designed and tested to keep your machines moving IP69k tested and certified for highest water resistance e1 type approval (according to automotive directive
More informationUltra-compact Laser Collimated Beam Sensor HL-T1 SERIES. Ultra-compact sensor head A high-functionality intelligent controller
887 Ultra-compact Beam Sensor SERIES Related Information General terms and conditions... P.1 Sensor selection guide...p.11~ / P.833~ Glossary of terms / General precautions... P.1019 / P.1027 About laser
More informationGX-5SU(B) is just 5.4 mm 0.213in in diameter, the smallest in existing DC two-wire sensors. It saves you space.
DC 2-wire Cylindrical Inductive Proximity SERIES Amplifier Built-in High performance & ease of use Robust in tightening The tightening torque has been improved to approx. four times greater than that of
More informationF3SJ-A F3SJ-A. Safety Light Curtain. safety light curtain that. Options. software. The F3SJ-A system is a fullfeatured
C R US Options n Handheld setting console n S manager programming software n F3SP/F3SX Safety Controller n Weld shields n IP67 enclosures n Multiple mounting options n escription F3SJ- Safety Light Curtain
More informationF3S-B. Safety Design for Category 2. Suitable for Detecting Human Bodies in a Dangerous Area. Safety Light Curtain. Features
Safety Light Curtain Suitable for Detecting Human Bodies in a Dangerous Area Safety Design for Category 2. Features The is a type 2 Safety Light curtain intended to be used as or with the safety related
More informationFrom ultra-thin lead frames to iron sheets... Double feed detection of various metal sheets
1147 Detector SERIES Related Information General terms and conditions... F-7 General precautions...p.151 PHOTO PHOTO MEASURE ITY From ultra-thin lead frames to iron sheets... Double feed detection of various
More informationDPST-NO None 2 channels Auto-reset Inverse (+/-) 24 VAC/VDC 4 G9SB-2002-A 1 channel or 2
Safety Relay Unit Ultra Slim Safety Relay Unit 17.5 mm wide models available with 2 or 3 poles. 22.5 mm wide 3 pole models also available EN Standards (TÜV approval) DIN-track mounting possible Ordering
More informationG9SX-GS. Safety Guard Switching Unit. A Safety Measure for Hazardous Operations That Does Not Lower Productivity. Auto Switching Function
Safety Guard Switching Unit CSM DS_E_6_1 A Safety Measure for Hazardous Operations That Does Not Lower Productivity Two functions support two types of application: Auto switching: For applications where
More informationMain contacts Auxiliary contact Number of input channels Rated voltage Model Category 24 VAC/VDC 3PST-NO SPST-NC 1 channel or 2 channels possible
Safety Relay Unit Four kinds of -mm wide Units are available: A -safety contact model, a -safety contact model, and models with safety contacts and OFF-delay safety contacts. Also available are 7.-mm wide
More informationNumber of input channels
Safety Relay Unit (Sensor Connector Type) CSM DS_E_3_1 Less Wiring Required with Safety Light Curtain Sensor connector allows direct connection to OMRON 3SJ Safety Light Curtains with PNP outputs. Reduces
More informationFrom ultra-thin lead frames to iron sheets... Double feed detection of various metal sheets
1135 Detector SERIES Related Information General terms and conditions... F-3 General precautions...p.1595 PHOTO PHOTO MEASURE From ultra-thin lead frames to iron sheets... Double feed detection of various
More informationProduct Discontinuation Notices. Discontinuation Notice of Safety Laser Scanner Type OS3101 series
PRODUCT NEWS Product Discontinuation Notices July 4, 2011 Presence Detection Sensors No. 2011195E Discontinuation Notice of Safety Laser Scanner Product Discontinuation Safety laser scanner Accessories
More informationInstallation Sensing distance Connection Output configuration Operation mode NO Operation mode NC
Standard (thin shape) Inductive Proximity Sensor Thin shape for space saving surface mounting Direct side wall mounting for bracket-less installation Ordering Information DC 3-wire Models Installation
More informationHigh-speed sampling and high resolution. The new choice for even more variegated data collection and processing.
1105 High Speed High Accuracy Eddy Current Type Digital Sensor SERIES Related Information General terms and conditions... F-7 Glossary of terms... P.1493 Sensor selection guide... P.1055~ General precautions...
More informationSafety Light Curtains GuardShield Remote Teach
Specifications Presence Sensing Safety Devices Description The system provides a remote means of changing a fixed blanking configuration within the GuardShield safety light curtain. This keyswitch box
More informationHR1S-AC Safety Relay Modules
HRS-AC Relay Modules Transistor output provided. Removable terminal block (HRS-AC52P) allows for easy module replacement. Fault diagnosis function with dual safety circuits. Internal relay operations can
More informationInductive Proximity Sensor
Inductive Proximity Sensor Miniature, Slim-styled Proximity Sensor Space-saving Sensor ideal for timing cam and dog detection. Four mounting holes provided: two each mounting from side or rear of the housing.
More informationInterlock Switches. Selection Guide. HS7A-DMC Magnetic Safety Switches
HSA-DMC Magnetic Safety Switches Key features: Compact size and easy positioning. Combination with proprietary relay modules achieves safety category 4 (EN954-1). Compact size ( 16 51mm) Positioning for
More informationNPN output PNP output Cord connection Cord length: 2 m Through-beam 7 m Light-ON. 2 m. (selectable by wiring) Diffuse reflective 0.
Built-in Amplifier Photoelectric Sensor E3V3 Easy-to-use, Low-cost Photoelectric Sensor Incorporating s that can be clearly seen from a distance. A series of models with an M8 metal junction connector
More informationEven a specular background does not affect the sensing performance if the sensor is located 30mm away from it (when directly opposite).
SERIES Convergent Reflective Micro Photoelectric Convergent Reflection Sensing Ensures Stable Detection Marked Conforming to EMC Directive Stable Detection by Convergent Reflective Mode Stable detection
More informationSafety Light Curtain (Type 4) F3SJ Ver. 2. New Models for Body Protection or Presence Detection
Safety Light Curtain (Type 4) F3SJ Ver. 2 New Models for Body Protection or Presence Detection Continuing advances in the F3SJ help to create even safer production systems. The new F3SJ will satisfy your
More informationBGS (at min. setting) BGS (at max. setting)
Compact Photoelectric Sensor with Built-in Amplifier EZ-LS CSM_EZ-LS_DS_E_7_ Distance-settable Sensor Unaffected by Workpiece Color and Background Distance-settable triangulation model unaffected by color.
More informationHigh-speed sampling and high resolution. The new choice for even more variegated data collection and processing.
1105 PHOTO PHOTO High Speed High Accuracy Eddy Current Type Digital Sensor SERIES Related Information General terms and conditions... F-7 Glossary of terms... P.1493 Sensor selection guide... P.1055~ General
More informationSERIES Amplifier Built-in Miniature-size Photoelectric Sensor
PHOTOEECTRIC SENSORS SERIES Amplifier Built-in Miniature-size Photoelectric EQ- Amplifier Built-in Micro-size Type RX -4 EQ- Marked Conforming to EMC Directive (Excluding -DS/DM) RX-S Remarkable Sensing
More information187 HG-C SERIES panasonic.net/id/pidsx/global Reliable detection in repeatability 10 μm mil Overwhelmingly stable
187 PHOTO PHOTO MEASURE CMOS Type Micro Laser Distance Sensor SERIES Related Information General terms and conditions... F-3 Glossary of terms / General precautions.p.1549~ / P.1552~ guide... P.169~ About
More informationOperation mode. Output configuration. Relay DC SSR. Light-ON Dark-ON (switch selectable) Relay DC SSR. Relay DC SSR
Built-in Power Supply Photoelectric Sensor CSM DS_E_12_3 Model Contribute to Overall Cost Reduction erminal Block Models Easy to wire and adjust. For the most recent information on models that have been
More informationE3Z. The New Standard for Compact, Long-range Photoelectric Sensors Conserves Energy and Natural Resources, One Million Sold Yearly
Compact Photoelectric Sensor with Built-in Amplifier EZ The New Standard for Compact, Long-range Photoelectric Sensors Conserves Energy and Natural Resources, One Million Sold Yearly Long sensing distance
More informationLS-500 SERIES. Digital Laser Sensor Amplifier-separated. Industry s smallest* Industry s smallest* + Stainless steel (SUS) enclosure
PHOTO PHOTO MEASURE ITY separated Digital Laser Sensor -separated SERIES Related Information General terms and conditions... F-7 SC-GU... P.985~ About laser beam... P.99~ Industry s smallest* panasonic.net/id/pidsx/global
More informationLong sensing range. 2 m ft. Retroreflective type. 200 mm in. Diffuse reflective type. 160 mm in
PHOTOEECTRIC SENSORS EX- SERIES Ultra-compact Photoelectric PNP output ight intensity type available monitor CX-4 EX-3 Miniature-sized and still mountable with M3 screws EX- EX- Conforming to EMC Directive
More informationpanasonic.net/id/pidsx/global
73 PHOTO PHOTO Digital Pressure Sensor For Gas SERIES Related Information General terms and conditions... F-3 Glossary of terms... P.1563~ guide... P.699~ General precautions... P.1566 MEASURE Simple &
More informationLong-distance Photoelectric Sensor with Built-in Amplifier. Connection method Sensing distance. --- Retro-reflective. (500 mm) Terminal block ---
Long-distance Photoelectric Sensor with Built-in Amplifier EG CSM_EG_DS_E_ _ Line of Long-distance Photoelectric Sensors for Large Workpieces Includes Retroreflective Models with Sensing Distance of m
More informationPhotoelectric Sensor with Built-in Amplifier with New Connector Options E3Z
Photoelectric Sensor with Built-in Amplifier with New Connector Options E3Z Compact Sensor Offers Long Sensing Distance and Superior Noise-Immunity D Photo-IC provides long sensing distance: 15 m and 10
More informationE3X-NA. Adjuster type standard that is the culmination of true ease and simplicity. Super Manual Fiber Amplifier. Features
Super Manual Fiber Amplifier Adjuster type standard that is the culmination of true ease and simplicity Features Self-explanatory LED bar displays of light levels The previous manual type used the stability
More informationSERIES. Ultra-compact Photoelectric Sensor. Long sensing range
EX- SERIES Ultra-compact Photoelectric Amplifier Built-in Miniature-sized and still mountable with M3 screws Conforming to EMC Directive U Recognition (Excluding m cable length type) Miniaturization by
More informationG9SA. Safety Relay Unit. The G9SA Series Offers a Complete Line-up of Compact Units. Model Number Structure
Safety Relay Unit G9 CSM_G9_DS_E The G9 Series Offers a Complete Line-up of Compact Units. Four kinds of -mm wide Units are available: A -pole model, a -pole model, and models with poles and OFF-delay
More informationHigh-speed sampling and high resolution. The new choice for even more variegated data collection and processing.
1023 PHOTO PHOTO High Speed High Accuracy Eddy Current Type Digital Sensor SERIES Related Information General terms and conditions... F- Glossary of terms... P.1397 Sensor selection guide... P.967~ General
More informationExpansion Unit G9SX-EX Safety 2 Instantaneous safety outputs
Flexible Safety Unit / Safety Guard Switching Unit G9SX/G9SX-GS CSM_G9SX_G9SX-GS_DS_E_8_1 Logical Function Adds Flexibility to Various Safety Circuits Be sure to read the Safety Precautions on page 45.
More informationModel Number Structure
Solid State Relays with Failure Detection Function G3PC CSM_G3PC_DS_E_1_1 Refer to Safety Precautions for All Solid State Relays. Detects failures in SSR used for heater temperature control and simultaneously
More information