Used with LE-D, LE-DA, LE-DL, LS-NVP/B Door Stations - SUPPLEMENT TO LEF INSTRUCTIONS -

Transcription

1 0907 all Master Station with Selective ontrol apability (Door elease or amera allup) Used with LD, LD, LDL, LSNVP/B Door Stations SUPPLMNT TO LF INSTUTIONS The is a compact, wall or desk mount master station able to selectively release a door or call up a camera. Used with any L or LSseries remote station, communication can be established with each station by selecting the channel on the master station. While the channel is selected, pressing the door release button (left of TLK button) will release only the associated door. When used for camera callup, a relay closure will be maintained as long as a station is selected. The system can have up to four stations, in any combination of masters or door stations (e.g. masters and doors). Mastertomaster communication is also a standard feature. (If communication between masters is not required, multiple 's can be used to talk to door stations. NMS & FTUS Speaker Station allin LDs Microphone Occupied LD Station Selectors TLK Button OFF Button Voice Volume ontrol Door elease Button FTUS: Selective door release control TV camera callup capability Single or multiple masters can be used in a system Master to master communication in a multimaster system Single talkpath, with pushtotalk operation at master, and hands free communication at sub station Large variety of sub stations available Surface or flush mount, with or without privacy (L, LN, LB, LBN) Weather resistant door stations (LD, LD, LDL) Vandal proof sub stations (LSS, LSS & LSNVP/B) Subs call in with momentary tone and LD, remaining lit for approximately 0 seconds Selective calling to sub stations Pg.

2 OMPONNTS & WIING Individual omponents for System: call master with selective door release LD Surface mount door station LD Flush mount door station with stainless steel faceplate LSNVP/B Vandal and weather resistant sub station, white powder coated (optional SBXNVP surface box) LSS Stainless Steel Gang sub station LSS Stainless Steel Gang sub station with red mushroom push button SBXG Surface mount box for LSS and LSS LSSG Stainless Steel Gang sub station (optional SBXSSG surface box) S Surge rrestor ( per wires being protected) P elay, input, N/O dry closure output. One required for each contact closure required off of each channel. an be momentary or maintained, according to wiring. 8L 8V D Form relay (N/O and N/ contacts),.5 power supply, use for intercom only, per system TMINL DFINITIONS: Positive VOLTG. Negative VOLTG WILL DMG TH UNIT. ~ Station number, communication to sub or other master "LL", for receiving a call from another master station ommon communication Occupied light control (0V D when system is occupied) ll all override control (Not used in system) OLOODD WIS: White ommon Door release activation ( when door release button is pressed) Brown Ground when station is pressed ed Ground when station is pressed Orange Ground when station is pressed LD/LD TMINL DFINITIONS: Station number ommon communication Negative LSNVP/B TMINL DFINITIONS: ed Station number ommon communication Green Negative LSS()/LSSG olor ode: ed Station number ommon communication Green Negative WIING & INSTLLTION: Before Installation: Make sure you have the proper power supply(ies) and all necessary and compatible equipment for the system. Lay out your system in advance, assigning station numbers for all sub station locations. Surge protection for the intercom equipment is recommended. dd S surge arrestors for the power supply, plus one per two wires connected to the master station. Wire: Shielded wire is strongly recommended. Use the proper gauge for the distance being run. Wiring between masters must be a multiconductor cable. If more than one cable is used to connect masters, the "", "", and number terminal wires must be in the same jacketed cable. If necessary, run multiple "" wires, one in each cable. Wiring Method: un intercom cables at least 0" away from all wiring, fluorescent lights, dimmer switches, and other electrical or electronic devices. Intercom wiring can cross wires at 90 degrees. Sub stations can be homerun to the nearest master station, or daisychained. If daisychained, include common wires plus individual wire per station on the run. In a SINGL MST SSTM : Subs can be wired with conductors homerun. Jumpers between "" and "" must be attached on all subs and at the master station. Intercom Locations: Do not install intercoms near dimmer or light switches, or other electrical wall devices. To prevent feedback, do not place sub stations backtoback on a common wall. Pg.

3 WIING DIGMS Most ommon pplications, Door Stations WIth Selective Door elease ed P Dr. # LD / LD el IMPOTNT: When using selective outputs, a separate relay and power source are required. Do not power external devices off of the system power supply. when "key" button is pressed P Dr. # el LD/ LD P Dr. # LD/ LD Transformer el NOT: When running conductors homerun to each sub (single master system only), leave jumper attached between & on master and door stations. Otherwise, remove jumpers and use separate wires for and terminals. onnect to door strike & power., Door Stations With MastertoMaster communication shown on channel With Selective Door elease LD/ LD ed ed P el Dr. # LD/ LD P Dr. # Transformer el onnect to door strike & power., Door Station With Master to Master ommunication Door Station wired on each station's own number terminal (different on each master) # # # ed ed ed when "key" button is pressed LD/ LD P Dr. # onnect to door strike & power. el Transformer Optional emote station: LSNVP LSS To # To To ed Grn Pg.

4 WIING DIGMS Multiple Masters for Door nswering Only, Door Stations No MastertoMaster ommunication Shown with door release relays IMPOTNT: When using selective outputs, a separate relay and power source are required. Do not power external devices off of the system power supply. ed ed P Dr. # el LD/ LD when "key" button is pressed P Dr. # el LD/ LD P Dr. # LD/ LD Transformer el onnect to door strike & power. Multiple 's (max. 0) and Door Stations No MastertoMaster ommunication Shown with 5 masters, doors. onnect up to 0 masters in parallel as shown, and up to door stations. PS 5UL ed ed ed ed ed when "key" button is pressed P Dr. # el LD/ LD LSNVP/B LSS ed Grn P el Dr. # onnect to door strike & power. Pg.4

5 WIING DIGMS (ont.) System with xternal Signaling () One door station with the ability to activate a separate doorbell Shown with external signaling and door release relays IMPOTNT: When using selective outputs, a separate relay and power source are required. Do not power external devices off of the system power supply. Transformer # # ed ed White ed el xternal Sounder P Dr. # el LD/ LD Transformer System with xternal Signaling () Selective external signaling relay outputs for each door station callin ed ed See other diagrams for door release connections. White ed LD/ LD ellow White ed To xternal signaling device & power LD/ LD ellow To xternal signaling device & power Pg. 5

6 WIING DIGMS (ont.), Door Stations Shown with both Door elease and TV amera allup relays IMPOTNT: When using selective outputs, a separate relay and power source are required. Do not power external devices off of the system power supply. ed LD/ LD P am. # el B * Diode P el Dr. # * Diode P Dr. # LD/ LD el * Diode: N400 value. equired for door strike relay only when relays are used on any one channel. NOT: This diagram shows separate & wires. In single master system only, one wire can be used for / when jumper remains attached between & on master and door stations. B P am. # el B onnect to door strike & power. onstant closure as long as station is selected. TOUBLSHOOTING GUID NT # POBLM POSSIBL US SOLUTION Door station does not call in (no call tone or LD light). Missing jumpers re there or conductors run to the door station? If wires, jumper must remain attached between and at both the door station and the master station. eplace jumper. In a multimaster system, the / jumper should be removed and wires should be connected. Door station does not call in (no call tone or LD light) wire connection. Missing connection of terminal. If communication works, check connection between terminal of door station and master. Test callin at master station by touching a jumper wire between # and terminal of master. If this rings the tone and lights the light, the wire from the door station is not connected properly. Door station does not call in (no call tone or LD light) wire connection. Miswiring of and terminals. heck that the and wire are not reversed. If they are, communication will work but callin will not. 4 No communication to door station. Miswiring of terminal. ommunication is between the and terminal of the door station to a # and terminal of the master station. If callin works, check the wire for continuity. heck the and wires at the sub to ensure that they are not reversed. 5 No mastertomaster communication. terminals miswired between masters. ommunication between masters is carried on the # wire of the calling master to the terminal of the receiving master. Verify that the terminal of the master that is being called is actually wired to the # terminal that is being selected on the calling master. 6 LF master has no communication or tone, but LD lights work. Wrong power supply is being used. The LD lights will operate with a power source from 6VD 4VD. The amplifier in the LF unit will only work when the system is supplied VD. Proper power supply is the. 7 Feedback when the volume control is turned up over halfway. / jumpers attached in a multimaster system. emove / jumpers on masters and door stations in the system, provided there are wires to the sub(s). If the sub only has wires in a multimaster system, the jumper must remain in place for the door callin to work. In this case, the side effect is the feedback problem when the audio volume is turned up. The only alternative is to run the proper wire to the door station(s) and remove all of the jumpers. 8 New installation has buzz, noise, or hum in system. Too close to and/or incorrect wire was used. If the units are too close to an source such as wiring or dimmer switches, move the intercom at least one stud space away from the source. Other precautions include using shielded cable. If shielded wire was used and there is still noise, tie all the shields together and ground to an earth ground or negative on the power supply. If more than one jacketed cable was used between masters, make sure the # terminals, terminal, and the terminals are all in the same jacketed cable. If multiple cables were used, include an wire in each cable that carries a station number wire in it. 9 Door release does not work. Miswire or lack of P relays. heck the WHIT wire coming out of the P board for voltage. When depressing the key button, VD is present across WHT and negative, which activates the relay. nsure that the black wires of the P are connected to WHT and either the BN, D, or OG wire for selective door release (which provides selective ground when the corresponding channel is selected). 0 No call tone between masters. No Privacy feature on. Features not available The unit does not have the PIV feature or the ability to send a call tone to another master station (as with the standard LF). This function is removed to allow the switch to be used for door release instead of privacy. an't release the door from the nd (additional masters) Wiring not connected properly. If door release works from the first master but not another(s), verify that selective door release wires are connected between masters. (WHT, BN, D, OG). P's are only required at one master. Pg.6 xternal Signaling device doesn't activate miswired Make sure that the WHIT wire of the is connected to the # terminal that is to be activating the relay, and that D and BLK are connected to and, respectively.

7 MODIFITIONS ONVTING TH P ONTT OUTPUT TO NOMLL LOSD Magnetic locks require Normally losed (N/) contacts, keeping power applied to the magnet to keep the door locked, and breaking power to release the door. These instructions explain how to change the P relay output from Normally Open (N/O) to Normally losed. Bottom view of relay module (inside plastic case) as it comes from the factory. (Normally Open) input 5 N/O 4 ellow Dry osure output To change to NOMLL LOSD contact, unsolder the wire from pin and resolder onto pin 4, as shown below. 5 N/ 4 ellow OPTIONS & SPIFITIONS OPTION:. Pressing the call button at the door station will activate a tone, plus light the red channel LD indicator at the master. The tone will be momentary, and the light will remain activated for approximately 0 seconds.. The person at the master station answers the call by pressing the selector button with the lit LD. If the LD has already gone out, the call can still be answered by pressing the selector button.. ommunication at the master station is "presstotalk, releasetolisten". ommunication at the door station is hands free. 4. If the "amera allup" feature is included, the associated relay will provide a maintained closure as long as the station is selected at the master. 5. With communication established to a door station, pressing the door release button (marked with key symbol, left of TLK button) will activate the door release mechanism at the corresponding door. The door release button will be nonfunctional if a station button is not pressed. 6. When the conversation is completed, the OFF button must be pressed to disengage the call. NOT: The does not have the "privacy feature", and also cannot send a call tone to another master or remote station in the system. SPIFITIONS: Power Source: at master. Use. Do not use power. Damage to the unit will result. ommunication Output: 0 ohms (receive); 0 ohms (transmit) ommunication: Pushtotalk, releasetolisten at master station. Hands free at sub station. alling: Master to sub: By voice Sub to master: all tone and LD Wiring: common plus individual per sub, looped; or conductors homerun from each sub. conductors homerun from each sub in a singlemaster system only. Use iphone #80 or #880 ( cond., or 8WG), or #80 ( cond. WG) conductors between master stations. Use iphone #8. Shielded cable is strongly recommended. Wiring Distance: 650' with WG;,600' with 8WG. Dimensions (HxWxD): 7/6" x 55/8" x /6" P ontact ating:, 0V or 4V D iphone ommunication Systems 700 0th ve. N.. Bellevue, W (45) FX (45) Toll Free Technical Support: mail techserv@aiphone.com Pg. 7 Instr. 0907JS