Optional IOB31 Board. x1 PCIe Link* (Expansion) x16 PCIe Link* (A0) PCI-X. 64-bit/66MHz. Connectors (A1, A2, A3, A4) PCI-X. x4 PCIe Link (B0) PCI-X

Transcription

1 Technical Information Jumpers and Connectors BPG () Graphics-Class Express Backplane Block Diagram Connectors (P & P) Ethernet Connectors (P & P) PICMG. System Host Board BPG Backplane System Host Board Slot (Edge connectors A, B, C & D) Optional IOB Board x e Link* (Expansion) x e Link* (A0) x e Connector (e) x e Connector (e) Power Connector (P) -bit/mhz Connectors (A, A, A, A) *Assumes Trenton TL or TML system host board -bit/mhz x e Link (B0) Connector (B) ISA Connectors (D, D) to ISA Bridge Connectors (C, C) Express to Dual Bridge -bit/mhz Layout Diagram.00..* *.0 * =.00*.* *.* SLTD.* x Express Link (A0).* SLTA SLTA SLTA SLTA SLTB SLTC P -bit/mhz -bit/mhz Express to Bridge x Express Link (B0) P P -bit MHz ISA Bus to ISA Bridge -bit/mhz es E x Express Link (es) V AUX Source JU AUX PSON E P P P0 AUX -V P P PWRBT RESET SMBUS P P Trenton Hole Pattern PICMG. Hole Pattern Notes: *IOB required to provide Express link to e slot **Optional and Ethernet connectivity provided by PICMG. SHB. Not all SHBs support this capability. Connector spacing: 0.00 Nominal PCB thickness:.00 Mounting holes:. diameter Connectors are populated based on model. Some holes are common to both hole patterns All dimensions are inches. Trenton Support Center BPG Technical Information -- Connectors

2 BPG () Configuration Jumper The setup of the configuration jumper on the backplane is described below. * indicates the default value of the jumper. NOTE: For the two-position jumper (-post), RIGHT and LEFT refer to positioning when the backplane is viewed with the slots at the top end of the backplane. Jumper JU Description Auxiliary Voltage Install on the LEFT if auxiliary voltage is provided by the standard supply. This option is used for systems which do not have either an ATX or EPS standard power input. This mode provides the necessary for the SHB s AUX signal lines. Sleep mode recovery is not supported using non- ATX/EPS power supplies. Install on the RIGHT if auxiliary voltage is provided by a separate AUX signal input pin. This enables the necessary SHB power signaling and allows recovery from sleep mode. This option is used for ATX or EPS standard power supplies. * BPG Connectors The connectors available on the BPG vary depending on the version of the backplane you have. Connectors for the -00 and -00 are defined below. BPG (-00) Connectors NOTE: on the connectors is indicated by the square pad on the PCB. P - ATX/EPS Power Connector pin dual row header, Molex # AUX 0 -V Trenton Support Center BPG Technical Information -- Connectors

3 BPG (-00) Connectors (continued) P - Power Connector pin mini fit JR, Molex #--0 P - Terminal Block Connector 0 position terminal block, Amp #--0 0 Amps per circuit 0 P - Terminal Block Connector 0 position terminal block, Amp #--0 0 Amps per circuit 0 P - Terminal Block Connector 0 position terminal block, Amp #--0 0 Amps per circuit 0 Trenton Support Center BPG Technical Information -- Connectors

4 BPG (-00) Connectors (continued) P - Power-On Connector pin single row header, Amp #0- P - Power Button Connector pin single row header, Amp #0- PWRBT# P - Reset Connector pin single row header, Amp #0- SHB_RST# P - Power Good Connector pin single row header, Amp #0- P0 - P - I/O Power Connector 0 pin dual row header, Molex #-00 IPMB_DA IPMB_CL SMDAT SMCLK PWRBT# 0 0 AUX SHB_RST# AUX_IN AUX_IN Universal Serial Bus () Connector pin dual row header, Molex #0--00 ( fused with self-resetting fuses) Trenton Support Center BPG Technical Information -- Connectors

5 BPG (-00) Connectors (continued) P - Universal Serial Bus () Connector pin dual row header, Molex #0--00 ( fused with self-resetting fuses) P - 0/00/000Base-T Ethernet Connector - LAN 0 pin shielded RJ- connector, Molex #0- TRP+ TRP- TRP+ TRP+ TRP- TRP- TRP+ TRP- P - 0/00/000Base-T Ethernet Connector - LAN pin shielded RJ- connector, Molex #0- TRP+ TRP- TRP+ TRP+ TRP- TRP- TRP+ TRP- P - System Management Bus Connector pin single row header, Amp #0- SMB Clock SMB Data Trenton Support Center BPG Technical Information -- Connectors

6 BPG (-00) Connectors NOTE: on the connectors is indicated by the square pad on the PCB. P - EPS Power Connector pin dual row header, Molex # AUX 0 -V P - Power Connector pin right angle mini fit JR, Molex #-00 P - Terminal Block Connector 0 position terminal block, Amp #--0 0 Amps per circuit 0 Trenton Support Center BPG Technical Information -- Connectors

7 BPG (-00) Connectors (continued) P - Terminal Block Connector 0 position terminal block, Amp #--0 0 Amps per circuit 0 P - Terminal Block Connector 0 position terminal block, Amp #--0 0 Amps per circuit 0 P - Power-On Connector pin single row header, Amp #0- P - Power Button Connector pin single row header, Amp #0- PWRBT# P - Reset Connector pin single row header, Amp #0- SHB_RST# P - Power Good Connector pin single row header, Amp #0- Trenton Support Center BPG Technical Information -- Connectors

8 BPG (-00) Connectors (continued) P0 - I/O Power Connector 0 pin dual row header, Molex #-00 IPMB_DA IPMB_CL SMDAT SMCLK PWRBT# 0 0 AUX SHB_RST# AUX_IN AUX_IN P - P - Universal Serial Bus () Connector pin dual row header, Molex #0--00 ( fused with self-resetting fuses) Universal Serial Bus () Connector pin dual row header, Molex #0--00 ( fused with self-resetting fuses) P - 0/00/000Base-T Ethernet Connector - LAN 0 pin shielded RJ- connector, Molex #0-000 TRP+ TRP- TRP+ TRP+ TRP- TRP- TRP+ TRP- Trenton Support Center BPG Technical Information -- Connectors

9 BPG (-00) Connectors (continued) P - 0/00/000Base-T Ethernet Connector - LAN pin shielded RJ- connector, Molex #0-000 TRP+ TRP- TRP+ TRP+ TRP- TRP- TRP+ TRP- P - System Management Bus Connector pin single row header, Amp #0- SMB Clock SMB Data Trenton SHB Optional Backplane I/O Support For the BPG TRENTON ETHERNET SHB LAN 0 LAN LAN 0 TQ, - - X X X X X TL, - - X X X X X TML, - - X X X X X MCG-series - - X X X X X LAN is a 0/00BASE-T Ethernet interface when using the TQ, TL or TML Backplane routings of interfaces & are factory build options on the TL and TML LAN is a 0/00/000BASE-T Ethernet interface when using a MCG-series SHB interfaces,, and are logical interfaces,, 0 and on the TQ system host board Note: The letter X indicates an interface connection routed to SHB edge connector C for use on the backplane. Trenton Support Center BPG Technical Information -- Connectors