General Specifications

Transcription

1 General Specifications GS 33J10D60-01EN Models VP6E5425, VP6E5426, VP6E5427 Expanded Test Functions Simulator Package Simulator Package [Release 6] GENERAL This document describes about specifications of Expanded Test Functions and / Simulator Packages that run on a human interface station (). FUNCTIONAL SPECIFICATIONS This package establishes intercommunications for, operation and monitoring functions, and engineering functions among several computers via network when used together with the virtual test functions of VP6E5420 test function package. In the environment where ProSafe-RS safety instrumented system is integrated with CENTUM VP (*1), SCS can also be used. When Exatif DCS Interface for Training Simulator (CENTUM VP Version) is used, a training system can be configured by connecting a dynamic and the CENTUM VP system (*2). For a computer to launch using its engineering function, the expanded test functions (license) and the test function package are required. When configuring a system which consists of several computers, at least a computer with the expanded test functions is mandatory. Examples of systems using the expanded test functions and the software packages required per each computer are explained as shown below. *1: Refer to the general specifications of the safety control functions package (GS 32Q03B10-31E and GS 32Q03B20-31E) for the test using the SCS. *2: Exatif is a product of Omega Simulation Co., Ltd. For details of its functions, refer to the General Specification (GS) issued by Omega Simulation Co., Ltd. Case 1: Test using s in several computers In, the test function license is installed consisting of the function and the function. This is launched by using the engineering function in the. In, the license is installed. The engineering function in the can be used to remotely launch the in the. ( remote start/stop function). Expanded test functions Test functions F01E.ai The table below shows the software licenses required for each computer. License VP6H1100 Standard Operation and Monitoring Function X VP6E5100 Standard Engineering Function X VP6E5420 Test Function X VP6E5425 Expanded Test Functions X VP6E5426 Simulator Package X VP6E5427 Simulator Package VP6F1 00 Standard Operation and Monitoring Function (*1) or VP6F1 05 Standard Operation and Monitoring Function for Simulator (*1) X X This table shows the minimum set of software licenses required for each computer to configure a Yokogawa Electric Corporation , Nakacho, Musashino-shi, Tokyo, Japan GS 33J10D60-01EN Copyright Feb (YK) 4th Edition Dec. 19, 2018 (YK)

2 2 Case 2: Test using s in several computers The is launched from the computer to perform the. In, the test function license is installed consisting both the function and the function. This is launched in the. In, the license is installed. This runs on the. Expanded test functions Test functions F02E.ai The table below shows the software licenses required for each computer. License VP6H1100 Standard Operation and Monitoring Function X X VP6E5100 Standard Engineering Function X VP6E5420 Test Function X VP6E5425 Expanded Test Functions X VP6E5426 Simulator Package VP6E5427 Simulator Package X VP6F1 00 Standard Operation and Monitoring Function (*1) or VP6F1 05 Standard Operation and Monitoring Function for Simulator (*1) X This table shows the minimum set of software licenses required for each computer to configure a

3 3 Case 3: Testing s in several computers from s in several Computers The following test environment can be configured by combining the functions. In, the test function license is installed consisting of the function and the function. Both the and the can run on the. In, the license and the license are installed. Both the function and the function can run on the. Expanded test functions Test functions F03E.ai The table below shows the software licenses required for each computer. License VP6H1100 Standard Operation and Monitoring Function X X VP6E5100 Standard Engineering Function X VP6E5420 Test Function X VP6E5425 Expanded Test Functions X VP6E5426 Simulator Package X VP6E5427 Simulator Package X VP6F1 00 Standard Operation and Monitoring Function (*1) or VP6F1 05 Standard Operation and Monitoring Function for Simulator (*1) X X This table shows the minimum set of software licenses required for each computer to configure a Connecting with upper layer applications Connecting with Exaopc OPC interface package can be established by using the control network communication emulation.

4 4 SYSTEM CONFIGURATION Standard system configuration Using the expanded test functions, several functions can be installed in a single computer; however, considerations to CPU loading on each computer and communication loading among computers are needed when configuring a system. For instance, some simulation windows of the may occupy the CPU for a long time, which prevent other processes from running. In order for the system to run stably for long hours, the CPU and communication loadings must be considered as shown below: The and the should not be installed in a single computer. A computer with Windows Server OS must be used for storing the project database when three or more computers are used for the test functions. A typical system configuration with considerations to the CPU loading and communication loading are as shown below. Computer 3 Computer 5 Computer 4 Project database Engineering function : Engineering function and Computer 3: Computer 4 and Computer 5: Figure Typical System Configuration In this configuration, in order to prevent operational delay in responses due to the increased computer s loading, or does not run on a computer where the project database is stored (e.g. in the above figure). Instead, the s run on and Computer 3, and the s run on Computer 4 and Computer 5. The table below shows the software package required for each computer. In this system configuration, the is remotely launched from the s engineering functions. Thus, standard engineering function, test function, and expanded test functions must be placed in the. Software Package Computer 3 Computer 4 Computer 5 VP6H1100 Standard Operation and Monitoring Function X X VP6E5100 Standard Engineering Function X VP6E5420 Test Function X VP6E5425 Expanded Test Functions X VP6E5426 Simulator Package X X VP6E5427 Simulator Package X X VP6F1 00 Standard Operation and Monitoring Function (*1) or VP6F1 05 Standard Operation and Monitoring Function for Simulator (*1) X X This table shows the minimum set of software licenses required for each computer to configure a F05E.ai

5 5 Large-scale System Configuration When the expanded test functions are applied for configuring a large-scale system, computers for the and the need to be independent. In the figure shown below, the s run on and Computer 3 and the s run on Computer 4 to 9. The can be remotely launched using the engineering functions in the and 2; but the does not run on the in this configuration. Computer 3 Project database Engineering function Engineering function Computer 4 Computer 5 Computer 6 Computer 7 Computer 8 Computer 9 F04E.ai : Engineering function Computer 3: : Engineering function and Computer 4 - Computer 9: The table below shows the software licenses required for each computer. License Computer 3 Computer 4 to 9 VP6H1100 Standard Operation and Monitoring Function X X VP6E5100 Standard Engineering Function X X VP6E5420 Test Function X X VP6E5425 Expanded Test Functions X X VP6E5426 Simulator Package X VP6E5427 Simulator Package X VP6F1 00 Standard Operation and Monitoring Function (*1) or VP6F1 05 Standard Operation and Monitoring Function for Simulator (*1) X X: Required : Not Required This table shows the minimum set of software licenses required for each computer to configure a The standard engineering function, the test function, and the expanded test functions are installed in the Computer 1 and, and the can be remotely launched using the engineering functions in these computers. Refer to APPLICATION CAPACITIES, for the limitations in using the software: In a large-scale system when the total number of the /SCS s exceeds the maximum number of those to be launched by a computer for engineering, two or more computers for engineering are required as shown in the above configuration. Up to eight /SCS s can run on a single computer.

6 6 Connecting with Exatif Plant Expert System The Exatif supports control network interface to create a training environment for a plant expert system. Unlike an ordinary test system, the plant expert system must be configured based on the Standard system configuration for more stable operations for longer period of time. Model computer Dynamic Manager Computer 3 Link software libraries interface interface Project database Engineering function : Engineering function : Computer 3: Figure Training Simulator System Configuration The following software licenses are required on each computer. F06E.ai License Computer 3 Note VP6H1100Standard Operation and Monitoring Function X VP6E5100 Standard Engineering Function X VP6E5420 Test Function X Including the and the VP6E5425 Expanded Test Functions X VP6E5426 Simulator Package X VP6E5427 Simulator Package X VP6F1 00 Standard Operation and Monitoring Function (*1) or VP6F1 05 Standard Operation X X and Monitoring Function for Simulator (*1) Exatif X X X Install this license in each computer. e.g. Link software libraries, interface, and interface This table shows the minimum set of software licenses required for each computer to configure a

7 7 APPLICATION CAPACITIES Number of /SCS s to run per computer: Max. 8 Number of /SCS to be connected: Max. 128 Number of to be connected: Max. 32 Number of computer to be connected: Max. 48 (*1) Number of /SCS s that a single computer for engineering (*2) can launch: Max. 40 (*3) *1: Including the number of computers where the Exaopc OPC interface package is installed. *2: For example, the and the in Large-scale System Configuration are the computers for engineering. *3: The number is valid under the condition that only the standard engineering function, the test function, and the expanded test functions run on a computer for engineering. The maximum number of the /SCS s becomes less when other applications run on the same computer. REMARKS FOR SYSTEM CONFIGURATIONS When connecting with the Exapoc OPC interface with the /SCS s, refer to the license s capacity of the Exaopc. When three or more computers are used for simulation tests, the project database has to be stored in a computer where the Windows Server OS is installed. OPERATING ENVIRONMENT The expanded test functions, the package, and the package run on a computer (IBM PC/ AT compatible). Hardware Requirement The hardware requirements conform to VP6E5100 Standard Engineering Function. is required as a communication device. (*1) *1: 1 Gbps is mandatory for configuring the Exatif plant expert system. Software Requirement The software requirements conform to VP6E5100 Standard Engineering Function. For the system configured by using the expanded test functions applied on multiple computers, the following software licenses are required. For configuring a plant training system, the Exatif plant expert system license from Omega Simulation Co., Ltd. is required. Refer to the descriptions and examples in this document for each software licenses required for each computer. The required licenses: For VP6E5425 Expanded test functions: VP6E5100 Standard engineering function VP6E5420 Test function (*1) In case the runs on a computer where VP6E5425 is installed, VP6H1100 Standard operation and monitoring function is also required. For VP6E5426 license: No other license is required. For VP6E5427 package: VP6H1100 Standard operation and monitoring function *1: Including the function and the function. GS 33J10D60-01EN Dec. 19,

8 8 When the models of AFV30, AFV40, A2FV50, and A2FV70 are used either for the target test or the virtual test, following software licenses are required. VP6F1700 Control Function for Field Control Station (for AFV30 /AFV40 ) VP6F1705 Control Function for Simulator (for AFV30 /AFV40 ) VP6F1800 Control Function for Field Control Station (for A2FV50 ) VP6F1805 Control Function for Simulator (for A2FV50 ) VP6F1900 Control Function for Field Control Station (for A2FV70 ) VP6F1905 Control Function for Simulator (for A2FV70 ) In order to perform the virtual tests, licenses of the control function for field control station and optional software are required in accordance with the number of the in the CENTUM VP project and/or the number of the SCS in the ProSafe-RS project to be used in the plant. For segregating the virtual test environment from the target test with the target or SCS, software licenses for those and SCS are required. MODELS AND SUFFIX CODES Model VP6E5425 Expanded Test Function -V Software license Suffix Code 1 Always 1 1 English version Description Model VP6E5426 Simulator Package -V Software license Suffix Code 1 Always 1 1 English version Description Model VP6E5427 Simulator Package -V Software license Suffix Code 1 Always 1 1 English version Description ORDERING INFORMATION Specify model and suffix codes. TRADEMARKS CENTUM, ProSafe and Exaopc are either registered trademarks or trademarks of Yokogawa Electric Corporation. All other company or product names appearing in this document are trademarks or registered trademarks of their respective holders. Subject to change without notice. GS 33J10D60-01EN Dec. 19,