General Specifications

Transcription

1 General Specifications Models AFV10S, AFV10D Field Control Unit Duplexed Field Control Unit (for Vnet/IP, for FIO, 19" Rack Mountable Type) R3 GENERAL This GS covers the hardware specifications of the Field Control Unit which is the processor of the Field Control Station (FCS). HARDWARE SPECIFICATIONS For the installation specifications and the environmental conditions common to the systems, refer to Vnet/IP System Overview (GS 33P01B10-31E). Processor VR5432 (133 MHz) Main Memory Capacity 32 Mbyte Memory Protection During Power Failure Battery Battery Back-up for Main Memory: Max. 72 hours Battery Recharge Time: Min. 48 hours FCU Status Contact Output 2 terminals (NC, C) Contact Points open during FCU failure Contact Rating: 30 V DC, max. 0.3 A Communication Interface Vnet/IP Interface: Dual-redundant ESB bus interface:dual-redundant or Single(In case of AFV10D, always Dual-Redundant.) Vnet/IP Communication Speed 1000 Mbps Full Duplex Connection Specifications Cable: CAT5e (Enhanced Category 5 cable), UTP Transmission: 1000Base-T and 100Base-TX compliance Connector: RJ45 connector Max. distance: 100 m (Distance between AFV10 and Layer 2 switch) Autonegotiation No. of Node Units Connectable Max. 14/FCU The total number of the local and remote nodes that can be connected to FCU are 14 or less. (The local nodes: 9 or less) 3 or less normally ; however, can be expanded to 14 if LFS1530 Application capacity Expansion Package (for AFV10 ) is purchased. No. of I/O Modules Max. 8/Node [19" Rack Mountable Type FCU] F01E.EPS Local Node Connection When connecting a Local Node to FCU, install ESB Bus Coupler Module (EC401) to FCU. EC401 must be installed in slot 7 and slot 8. To make single configuration, EC401 must be installed in slot 7, and Slot 8 must be empty. Remote Node Connection When connecting a Remote Node to FCU, install ER Bus Interface Master Module (EB401) to FCU. To make single configuration, EB401 must be installed in an odd-number slot, and make a space on the right side of the installed EB401. See ER Bus Interface Master Module (for FIO) (GS 33Q06Q48-31E) for further information. Power Supply (specify with Suffix Codes) Voltage: V AC, Frequency: 50/60 Hz Voltage: V AC, Frequency: 50/60 Hz Voltage: 24 V DC Power Consumption V AC: 200 VA V AC: 230 VA 24 V DC: 5.5 A Weight Approx. 7 kg (AFV10S) Approx. 8 kg (AFV10D) Yokogawa Electric Corporation , Nakacho, Musashino-shi, Tokyo, Japan Tel.: Fax.: Copyright Sep.13,2004 3rd Edition May 1,2005

2 TM1 READY FUSE RL1 CN1 (PSU-L) TM V AC L N CN2 (PSU-R) <<Contents>> <<Index>> 2 Mounting 19" Rack Mounting: Rack mount (M5 x 8 screws) Insulation bush (accessory) Connection Power Supply: M4 screw terminal connection Grounding: M4 screw terminal connection Contact Output: M4 screw terminal connection Network: Connect CAT5e (Enhanced Category 5 cable) to Layer 2 switch. Regulatory Compliance For the detailed information of following standards, see Integrated Production Control System CENTUM CS 3000 System Overview (GS 33Q01B10-31E). Safety Standards [CSA] (for V AC power supply) [CE Mark] (for V AC power supply) EMC Conformity Standards [CE Mark] (for V AC and 24 V DC power supply) [C-Tick Mark] (for V AC and 24 V DC power supply) System Configuration The FCS consists of the FCU and Node Units, and the ESB bus or the ER bus to connect them together. Dual-redundant Vnet Local Node Dual-redundant ESB bus Maximum of 14 Nodes Local Node FIO Dual-redundant ER bus Remote Node I/O signal connection F02E.EPS All Rights Reserved. Copyright 2004, Yokogawa Electric Corporation Sep.13,

3 3 LIMITATIONS OF INSTALLATION AND NOTICES FOR INSTALLATION For installing I/O modules in AFV10S and AFV10D, the quantity and allocation are limited. Also, when installing a node unit to the dedicated cabinet, there are limitations of installation under the ambient operating temperature conditions. When modules with built-in barriers are installed in AFV10, an insulating partition kit (Part No. T9083ND) must be installed. For details, please refer to Limitations and Precautions for Installation (GS 33Q06Q01-31E). EXTERNAL DIMENSIONS Unit: mm Hole for 19" rack mounting (8 M5 screw holes) F03E.EPS All Rights Reserved. Copyright 2004, Yokogawa Electric Corporation May 1,

4 4 SOFTWARE REQUIREMENT For AFV10S and AFV10D, LFS1500 Control Function for Basic Field Control Unit (for FIO, for Vnet/IP) is required. Specify these control functions with suffix codes. For the specifications of LFS1500, refer to GS 33P03K10-31E. The number of the connectable node units and the application capacity can be expanded if LFS1530 application Capacity Expansion Package (for AFV10 ) is purchased. REQUIREMENTS FOR USING SEM (Sequence of Events Manager) To use SEM, the following are required. AFV10 : Style 2 or later (Style No. is indicated on the component tag) EC401: Style 2 or later (Style No. is indicated on the component tag) For details, refer to GS 33P02N80-31E SEM Sequence of Events Manager (for FIO and Vnet/IP). ACCESSORIES AND SPARE PARTS The spare parts listed below are provided with the FCU. Parts Names Insulating bush Parts Numbers Quantity Remarks S9049PM - 8 Accessory T03E.EPS All Rights Reserved. Copyright 2004, Yokogawa Electric Corporation May 1,

5 5 MODELS AND SUFFIX CODES Field Control Unit (19 Rack Mountable Type) Model AFV10S Field Control Unit (for Vnet/IP, for FIO, for 19" Rack Mountable) -S Standard type 3 Dual-Redundant Vnet/IP, Single power supply 4 Dual-Redundant Vnet/IP, Dual-Redundant power supply 1 Always 1 Suffix Codes Option Code V AC power supply (Conforms to Safety Standards CSA C22.2 No ) (*1) V AC power supply (with CE Mark and C-Tick Mark) (*2) 4 24 V DC (with CE Mark and C-Tick Mark) (*2) 0 Basic type 1 With ISA Standard G3 option 1 LFS1500 Basic software license for Control Function for Basic Field Control Unit (for FIO, for Vnet/IP) (*3) /ATDOC Explosion Protection Manual (*4) *1: AFV10S with this suffix code dose not have CE Mark or C-Tick Mark. For CSA, install this product in a keyed metallic cabinet. *2: For CE Mark and C-Tick Mark, install this product in a keyed metallic cabinet. *3: This suffix code can be used in the software version of R3.05 or later. *4: Select the option code "/ATDOC" to follow the ATEX Directive for use in potentially explosive atmospheres. Duplexed Field Control Unit (19 Rack Mountable Type) T01E.EPS Model AFV10D Duplexed Field Control Unit (for Vnet/IP, for FIO, for 19" Rack Mountable) -S Standard type 4 Dual-Redundant Vnet/IP, Dual-Redundant power supply 1 Always 1 Suffix Codes V AC Power Supply (Conforms to Safety Standards CSA C22.2 No ) (*1) V AC Power Supply (with CE Mark and C-Tick Mark) (*2) 4 24 V DC (with CE Mark and C-Tick Mark) (*2) 0 Basic type 1 With ISA Standard G3 option 1 LFS1500 Basic software license for Control Function for Basic Field Control Unit (for FIO, for Vnet/IP) (*3) Option Code /ATDOC Explosion Protection Manual (*4) *1: AFV10D with this suffix code dose not have CE Mark or C-Tick Mark. For CSA, install this product in a keyed metallic cabinet. *2: For CE Mark and C-Tick Mark, install this product in a keyed metallic cabinet. *3: This suffix code can be used in the software version of R3.05 or later. *4: Select the option code "/ATDOC" to follow the ATEX Directive for use in potentially explosive atmospheres. Insulating Partition Kit T02E.EPS Part No. T9083ND Insulating Partition Kit Configuration of Insulating Partition Kit T04E.EPS Part No. T9083NE T9083NG T9083LB Insulating Partition Insulating Partition for V-net 2 spanner screws for T9083NG T05E.EPS ORDERING INSTRUCTIONS Specify model and suffix codes. All Rights Reserved. Copyright 2004, Yokogawa Electric Corporation May 1,

6 6 TRADEMARK CENTUM is a registered trademark of Yokogawa Electric Corporation. The trademark Vnet/IP is under going approval procedure. Other company and product names appearing in this document are trademarks or registered trademarks of their respective holders. All Rights Reserved. Copyright 2004, Yokogawa Electric Corporation Subject to change without notice. Dec.1,