Barriers. Automation & Sensing.

Transcription

1 Automation & Sensing Selection Guide Discrete Input EB3C Discrete Input EB3 Discrete Input Barrier Discrete Output EB3 Discrete Output Switches and Pilot Devices General Information OI Touchscreens PCs Automation Software Power Supplies Sensors Communication Table of Contents ED ighting - Pg. 1 Automation & Sensing - Pg. 21 Safety - Pg. 281 Switching & Controls - Pg. 483 Index - Pg. 1039

2 Selection Guide OI Touchscreens Discrete Input Barrier Selection Guide Model EB3C-**A EB3C-**D EB3-**D Appearance Sensors Power Supplies Automation Software PCs Page Ratings U: Class I, II, III Div1 / Group A, B, C, D, E, F, and G Class I, Zone 0 / [AExia] II C FM: Class I, II, III Div1 / Group A, B, C, D, E, F, and G Class I, Zone 0 / [AExia] II C PTB (ATEX): II(1)G [Exia] IIC: Gas vapor II(1) D[Exia] IIIC: Dust PTB (IECEx) [Exia]IIIC IEC Ex: [Exia] II C CQST: [Ex ia Ga] IIC TIIS: Discrete input barrier [Exia] IIC Switch (EB9Z-A) Exia IICT6 Switch (EB9Z-A1) Exia IIBT6 K: [Exia] II C KCs: [Exia] II C, [Exia D] KR: [Exia] IIC, [Exia] III C (pending) Degree of Protection IP20 IP20 IP20 umber of Channels Relay Output: 1,2,3,5,6,8,10 Transistor Output: 1,2,3,5,6,8,10,16 Relay Output: 1,2,3,5,6,8,10 Transistor Output: 1,2,3,5,6,8,10,16 Power Voltage 100 to 240V AC (U rating: VAC) 24V DC 24V DC Output Relay Transistor (Sink/Source) Relay Transistor (Sink/Source) U: Class I, II, III, Div. 1, Groups A, B, C, D, E, F and G Class I, Zone 0, [AExia] II C PTB (IECEx): [Exia] II C PTB (ATEX): II (1) G [Exia] II C II (1) D [ExiaD] CQST: [Exia] II C TIIS: [Exia] II C EB3-2D: EB3-2R5D: Connection Screw Terminal Screw Terminal, Connector Screw Terminal Mounting Size (excluding projections) 35-mm-wide DI rail Panel mounting 42W 75H 77.5D (1 channel) 65W 75H 77.5D (2, 3 channels) 110.5W 75H 77.5D (5, 6, 8 channels (common)) 171.5W 75H 77.5D (8, 10 channels) 35-mm-wide DI rail Panel mounting Weight (approx.) 380g (EB3C-R10A) 390g (EB3C-R16CD) 42W 75H 77.5D (1 channel) 65W 75H 77.5D (2, 3 channels) 110.5W 75H 77.5D (5, 6, 8 channels (common)) 171.5W 75H 77.5D (8, 10, 16 channels (common)) Relay 2 safety circuits 2 safety circuits, 5 auxiliary circuits 35-mm-wide DI rail / Panel mounting 65.0W 75.0H 77.5D (EB3-2D) 110.5W 75.0H 77.5D (EB3-2R5D) 220g (EB3-2D) 300g (EB3-2R5D) Communication 242

3 Selection Guide Discrete Output Barrier Model EB3-**A EB3-**D Appearance Page 259 Ratings U: Class I, II, III Div1 / Group A, B, C, D, E, F, and G Class I, Zone 0 / [AExia] II C FM: Class I, II, III Div1 / Group A, B, C, D, E, F, and G Class I, Zone 0 / [AExia] II C PTB (ATEX): II(1)G [Exia] IIC: Gas vapor II(1)D [Exia] IIIC: Dust PTB (IEC-Ex) [Exia] IIC [Exia] IIIC CQST: Ex ia Ga IEC Ex: [Exia] II C TIIS: Discrete output barrier [Exia] II C K: [Exia] II C KCS: [Exia] II C, [Exia D] KR: [Exia] IIC, [Exia] III C (pending) Degree of Protection IP20 IP20 umber of Channels 1, 2, 3, 5, 6, 8, 10 1, 2, 3, 5, 6, 8, 10, 16 Power Voltage 100 to 240V AC (U rating: 100 ~ 120V AC) 24V DC Input Transistor input (sink) Transistor input (source) Transistor input (sink) Transistor input (source) Connection Screw Terminal Screw Terminal, Connector Mounting Size (excluding projections) 35-mm-wide DI rail Panel mounting 42W 75H 77.5D (1 channel) 65W 75H 77.5D (2, 3 channels) 110.5W 75H 77.5D (5, 6, 8 channels) 171.5W 75H 77.5D (8, 10 channels) 35-mm-wide DI rail Panel mounting Weight (approx.) 360g (EB3-S10SA) 360g (EB3-S16CSD) Switches and Pilot ights Page 267 Pilot ight and Miniature Pilot ight IP65 (IEC60529) (except for terminals) EB3P-U/I: IP40 Illuminated Switch IP65 (IEC60529) (except for terminals) EB3P-SAW**: IP54 Buzzer IP20 (IEC60529) (except for terminals) 42W 75H 77.5D (1 channel) 65W 75H 77.5D (2, 3 channels) 110.5W 75H 77.5D (5, 6, 8 channels) 171.5W 75H 77.5D (8, 10, 16 channels (common)) OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 243

4 Sensors Power Supplies Automation Software PCs OI Touchscreens EB3C Intrinsically Safe: EB3C Discrete Input Key features: Applicable Standards IEC60079 compliant Dry-contact switches can be connected to the EB3C 8- and 16-circuit types are available in common wiring types, ideal for connection to PCs (DC voltage only) Universal AC power voltage (100 to 240V AC) or 24V DC power (U rating: 100 ~ 120V AC) o grounding required IDEC s original spring-up terminals minimize wiring time Installation: 35-mm-wide DI rail mounting or direct screw mounting Global usage USA: U/FM Europe: CE marking, Global: IECEx ATEX Japan: TIIS China: CQST Korea: KCs Ship class: K (Japan), KR (Korea pending) Entity Barrier Parameters Ta= 60 C, Um= 250V, (Um=125V U only), Uo=13.2V, Io= 14.2mA, Pn-n Io=227.2mA, Po= 750mW at max 16 channels Pn-n Connector Type Po= 46.9mW at each channel Io(mA) Po(mW) Co(μF) ote 1 Added to above table, the next values combined o and Co are allowable; Io(mA) o(mh) 175* * Co(µF) 0.90* * TIIS, K only Ta=60 C, Um=250V * * Combined o(mh) ch 16 ch Seperate Common 16 Uo Io Po Co o 13.2V 14.2mA 46.9mW 0.47μF 87.5mH 13.2V 227.2mA 750mW 0.365μF 0.425mH ote 2 The intrinsic safe apparatus and wirings shall be accordance to following formulas; for example: Ui Uo Ii Io Pi Po Ci+Cc Co i+c o *: Therefore, the values are allowable only at i 1%o and Ci 1%Co of the intrinsic safe apparatus. (In the case of 50% of Co and o parameters are applicable,the maximum capacitance allowed shall not be more than Co = 1 µf for IIB and Co= 600 nf for IIC.) Dry Contact Switches Spring-up Fingersafe Terminals Reduce Wiring Time Dry-contact switches can be connected to the EB3C. Communication Finger-safe B Series CW Series Connector Type MI connector on the non-hazardous side Easy connection to PCs Wiring reduced Various 20-pin MI connectors can be connected 244 HW Series Common Wiring for PC Inputs 8- and 16-circuit types are available in common wiring types, ideal for connection to PCs (DC voltage only).

5 EB3C EB3C Electrical Specifications Ratings Degree of Protection Installation ocation Discrete Input Barrier on-intrinsically Safe Circuit Maximum Voltage (Um) Intrinsically Safe Circuits on-intrinsically Safe Circuits See Certification umbers table below IP20 (IEC60529) Safe indoor place (non-hazardous area) 1-channel Wiring Method Separate Wiring Rated Operating Voltage 12V DC ±10% Rated Operating Current 10 ma DC ±20% Contact Configuration 1O Rated Insulation Voltage (Ui) Relay Output Transistor Output 250V AC 50/60Hz, 250V DC 125V AC 50/60Hz, 125V DC (U rating) 16-channel Common Wiring 250V AC (U rating: 125V AC), 125V DC Thermal Current (lth) 3A (common terminal: 8A) Contact Resistive AC: 750 VA, DC: 72W Allowable AC: 750 VA (cos ø = 0.3 to 0.4) Power Inductive DC: 48W (/R = 7 ms) Rated Resistive Inductive Minimum Applicable Contact Resistance O Time OFF Time Mechanical ife Electrical ife Short-circuit Protection Rated Voltage Maximum Voltage Maximum Current eakage Current Voltage Drop Clamping Voltage Inrush Current O Time OFF Time Short-circuit Protection EB3C General Specifications AC Rated Voltage 100 to 240V AC (U rating: 100 ~ 120V AC) Allowable Voltage Range 85 to 264V AC (U rating: 85 ~ 125V AC) Rated Frequency 50/60 Hz (allowable range: 47 to 63 Hz) Inrush Current 10A (100V AC) 20A (200V AC) 250V AC 3A, 24V DC 3A 250V AC 3A (cos ø = 0.3 to 0.4) 24V DC 2A (/R = 7 ms) 0.1V DC, 0.1 ma (reference value) 50 mω maximum (initial value) 12 ms maximum (rated voltage) 10 ms maximum (rated voltage) 20,000,000 operations minimum (at 18,000 operations/hour, without load) 100,000 operations minimum (at 1,800 operations/hour, rated load) one 24V DC 30V DC 100 ma (connector type: 15 ma) 0.1 ma maximum 1.5V maximum 33V (1W) 0.5A maximum (1 sec) 0.1 ms maximum (resistive load) 0.4 ms (typical) (resistive load) one DC 24V DC 21.6 to 26.4V DC 10A Specifications Dielectric Strength (1 minute, 1 ma) Operating Temperature Storage Temperature Operating Humidity Atmosphere Pollution Degree Insulation Resistance Vibration Resistance Shock Resistance Terminal Style Mounting Damage imits Operation Extremes (relay output only) Damage imits Power Consumption (approx.) Weight (approx.) Between intrinsically safe circuit and nonintrinsically safe circuit: V AC Between AC power and output terminal: 1500V AC Between DC power and transistor output terminal: 1000V AC 20 to +60 C (no freezing) 20 to +60 C (no freezing) 45 to 85% RH (no condensation) 800 to 1100 hpa 2 (IEC60664) 10 MΩ minimum (500V DC megger, between the same poles as the dielectric strength) Panel mounting: 10 to 55 Hz, amplitude 0.75 mm DI rail mounting: 10 to 55 Hz, amplitude 0.35 mm Panel mounting: 10 to 55 Hz, amplitude 0.5 mm DI rail mounting: 10 to 55 Hz, amplitude 0.35 mm Panel mounting: 500 m/s² (3 times each on X, Y, Z) DI rail mounting: 300 m/s² (3 times each on X, Y, Z) M3 screw terminal 35-mm-wide DI rail or panel mounting (M4 screw) 9.6 VA (EB3C-R10A at 200V AC) 4.8 W (EB3C-R16CD at 24V DC) 390g (EB3C-R16CD) EBC3 Certification umbers Certification Certification Ratings Organization umber Class I, II, III Div. 1 U Group A, B, C, D,E, F, and G E Class I, Zone 0 / [AExia] II C FM Class I, II, III Div. 1 Group A, B, C, D,E, F, and G Class I, Zone 0 / [AExia] II C PTB (ATEX) II(1)G [Exia] II C: Gas Vapour, II(1)D [Exia] III C: Dust PTB09 ATEX2046 PTB (IEC-EX) [Exia] II C: Gas, Vapour [Exia] III C: Dust IECEx PTB TIIS Japan Relay barrier: [Exia] II C Switch (EB9Z-A) : Exia II C T6 Switch (EB9Z-A1) : Exia II B T6 TC TC15758 TC15961 Class K [Exia] II C TYPE TEST o. 13T606 CQST [Exia Ga] II C CEx KCs Relay Barrier : [Exia] II C 14-AV4BO-0373 KR [Exia] IIC Pending Class K is Japan Shipping agency approval, Class KR is Korean shipping agency approval. OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 245

6 EB3C Part umbers Communication Sensors Power Supplies Automation Software PCs OI Touchscreens Discrete Input Power Voltage 100 to 240V AC (U rating: 100 ~ 120V AC) 24V DC Connection to on-intrinsically Safe Circuit Screw Terminal Connector Input Wiring Method Separate/Common Wiring Compatible Output Relay umber of Channels Part umber Weight (approx) g 1 EB3C-R01A EB3C-R02A EB3C-R03A EB3C-R05A EB3C-R06A EB3C-R08A EB3C-R10A 380 Common Wiring Only 8 EB3C-R08CA 280 Separate/Common Wiring Compatible Common Wiring Only Separate/Common Wiring Compatible Common Wiring Only Separate/Common Wiring Compatible Common Wiring Only Common Wiring Transistor (Sink/Source) Transistor Relay Sink Source Transistor (Sink/Source) Transistor Sink Source 1 EB3C-T01A EB3C-T02A EB3C-T03A EB3C-T05A EB3C-T06A EB3C-T08A EB3C-T10A EB3C-T08CKA EB3C-T16CKA EB3C-T08CSA EB3C-T16CSA EB3C-R01D EB3C-R02D EB3C-R03D EB3C-R05D EB3C-R06D EB3C-R08D EB3C-R10D EB3C-R08CD EB3C-R16CD EB3C-T01D EB3C-T02D EB3C-T03D EB3C-T05D EB3C-T06D EB3C-T08D EB3C-T10D EB3C-T08CKD EB3C-T16CKD EB3C-T08CSD EB3C-T16CSD 350 Sink EB3C-T16CKD-C Source EB3C-T16CSD-C 330 Accessories Item Part umber Description DI Rail BA000 Steel (1m long, 7.5mm high) BAA1000 Aluminum (1m long, 10.5mm high) End Clip B6 Medium DI rail end clip Static Electricity Caution Plate EB9Z-1 Polyester 20 (W) x 6 (H) mm 246

7 EB3C Internal Circuit Block Diagrams AC Power, Relay Output Type Green ~ 1 P2 2 P3 3 Yellow Yellow Yellow A1 C1 A2 C2 A3 C3 External Wiring Examples DC Power, Transistor Output Type + Green ~ 1 P2 2 P3 3 Yellow Yellow Yellow A1 C1 A2 C2 A3 C3 Circuit Diagrams Connector Wiring, Sink Output Type Green ~ Wiring Examples Yellow Yellow + A1 A16 C1 C2 Hazardous Area on-hazardous Area Transistor Output Type (Ex.: EB3C-T06A) Transistor Sink Output Type (Ex.: EB3C-T08CKD) Transistor Source Output Type (Ex.: EB3C-T08CSD) 1 P2 2 P3 3 P4 4 P5 5 P6 6 A1 C1 A2 C2 A3 C3 A4 C4 A5 C5 A6 C6 100 to 240V AC ote: On the sink/source transistor output type, ter minals A can be used as a positive common line. Relay Output Type (Ex.: EB3C-R06A) 1 P2 2 P3 3 P4 4 P5 5 P6 6 A1 C1 A2 C2 A3 C3 A4 C4 A5 C5 A6 C6 100 to 240V AC Power AC/DC Power 24V DC + 24V DC P2 P3 P4 P5 P6 P7 P8 1 2 A1 A2 A3 A4 A5 A6 A7 A8 C1 C2 Power 24V DC Relay Output Common Wiring Type (Ex.: EB3C-R016CD) 24V DC P2 P3 P4 P5 P6 P7 P8 1 2 P2 P3 P4 P5 P6 P7 P A1 A2 A3 A4 A5 A6 A7 A8 C1 C2 24V DC P A1 A2 A3 A4 A5 A6 A7 A8 C1 C2 A9 A10 A11 A12 A13 A14 A15 A16 C3 C4 Power AC/DC Power 24V DC OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 247

8 EB3C Dimensions (mm) OI Touchscreens Screw Terminal EB3C *05 EB3C *08 EB3C *02 EB3C *06 EB3C *10 EB3C *01 EB3C *03 EB3C *08C EB3C *16C EB3C *05 EB3C * EB3C *01 EB3C *02 EB3C *03 EB3C *06 EB3C *08C EB3C *10 EB3C *16C ø4.4 ø4.4 PCs ø6 hole ø6 hole Communication (4) 65 (4) 65 Automation Software Power Supplies Sensors Mounting Hole Hole ayout ayout (Screw (Screw Mounting) Mounting) 2-M4 tapped or 2-ø4.5 mounting holes 2-M4 tapped or 2-ø4.5 mounting holes Connector Connector Type EB3C T16C -C M4 tapped or 2-ø4.5 mounting holes 2-M4 tapped or 2-ø4.5 mounting holes M4 tapped or 2-ø4.5 mounting holes 2-M4 tapped or 2-ø4.5 mounting holes ø M4 tapped or 4-ø4.5 mounting holes 4-M4 tapped or 4-ø4.5 mounting holes Applicable 3 max. Crimping Crimping Terminal 5.4 Terminal min. ø3.2 min. 3 max. 5.4 min. 6 (4) ø4.5 holes 65 4-M4 or 4-ø4.5 holes 97 Mounting Hole ayout 65 Applicable Crimping Terminal Applicable Crimping Terminal ø3.2 min. ø3.2 min. 6 max. 6 max. 6 max. Stripping the Wire End 3 max. Stripping Solid the Wire Wire End Solid Wire 6 to 8 mm 5.4 min. Solid Wire - Strip wire end Stripping the Wire 6 to 8 End mm Stranded Wire Wire (Ferrule) 6 to - use 8 mma ferrule Stranded Wire (Ferrule) 6 to 8 mm Stranded Wire 6 to (Ferrule) 8 mm to 8 mm 248

9 EB3C Connector Wiring Terminal Arrangement EB3C-T16CKD-C (Sink) CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH1 6 A9 A1 0 A11 A1 2 A13 A1 4 A15 A1 6 C C A1 A2 A3 A4 A5 A6 A7 A8 C1 C2 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 +V COM Internal Circuit EB3C EB3C-T16CSD-C (Source) V (C1) A1-A1 6 COM (C2) CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH1 6 CO M Input I0-I15 A9 A1 0 A11 A1 2 A13 A1 4 A15 A1 6 C C A1 A2 A3 A4 A5 A6 A7 A8 C1 C2 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 V COM Internal Circuit EB3C COM (C2) A1-A16 Input I0-I15 CO M PC CHn An COM PC 1 2 Internal Circui t CHn + An COM Internal Circuit EB3C-T16CKD-C FC4A-16B3 Terminal Output Input Terminal 20 A1 I A9 I A2 I A10 I A3 I A11 I A4 I A12 I A5 I A13 I A6 I A14 I A7 I6 8 7 A15 I A8 I7 6 5 A16 I V COM 4 3 C COM 3 2 COM C 2 1 C C 1 EB3C-T16CSD-C FC4A-16B3 Terminal Output Input Terminal 20 A1 I A9 I A2 I A10 I A3 I A11 I A4 I A12 I A5 I A13 I A6 I A14 I A7 I6 8 7 A15 I A8 I7 6 5 A16 I V COM 4 3 C COM 3 2 COM C 2 1 C C 1 ote: The wiring in dashed line does not affect the operation of the EB3C. Applicable connector is IDEC JE1S-201. Output power for PC outputs is supplied by the EB3C, therefore the PC output does not need an external power supply. OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 249

10 EB3C Wiring Example of Intrinsically Safe External Inputs OI Touchscreens 1. Common Wiring (Maximum 16 circuits) All input lines are wired to a common line inside the intrinsically safe switch (one common line per intrinsically safe circuit). 1. Common Wiring (Maximum 16 circuits) All input lines are wired to a common line inside the intrinsically safe switch (one common line per intrinsically safe circuit). A1 A1 A2 P2 A2 P2 A3 P3 A3 P3 A4 P4 A4 P4 A5 P5 A5 P5 A6 P6 A6 P6 A7 P7 A7 P7 A8 P8 A8 P8 C1 1 C1 1 C2 2 C2 2 A9 P9 A9 P9 A10 0 A10 0 A11 1 A11 1 A12 2 A12 2 A13 3 A13 3 A14 4 A14 4 A15 5 A15 5 A16 6 A16 6 C3 3 C3 3 C4 4 C4 4 PCs Some input lines are wired to a common line inside the intrinsically safe switches, while others are outside switches (one common line per intrinsically safe circuit). Some input lines are wired to a common line inside the intrinsically safe switches, while others are outside switches (one common line per intrinsically safe circuit). Automation Software All input lines are wired to a common line outside the intrinsically safe switch (one common line per intrinsically safe circuit). All input lines are wired to a common line outside the intrinsically safe switch (one common line per intrinsically safe circuit). Power Supplies Sensors Communication A1 A1 C1 1 C1 1 C2 2 C2 2 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A7 P7 A7 P7 C7 7 C7 7 A8 P8 A8 P8 C8 8 C8 8 A9 P9 A9 P9 C9 9 C9 9 A10 0 A10 0 C10 10 C10 10 A1 A1 A2 P2 A2 P2 A3 P3 A3 P3 A4 P4 A4 P4 A5 P5 A5 P5 A6 P6 A6 P6 A7 P7 A7 P7 A8 P8 A8 P8 C1 1 C1 1 C2 2 C2 2 A1 A1 A2 P2 A2 P2 A3 P3 A3 P3 A4 P4 A4 P4 A5 P5 A5 P5 A6 P6 A6 P6 A7 P7 A7 P7 A8 P8 A8 P8 C1 1 C1 1 C2 2 C2 2 A9 P9 A9 P9 A10 0 A10 0 A11 1 A11 1 A12 2 A12 2 A13 3 A13 3 A14 4 A14 4 A15 5 A15 5 A16 6 A16 6 C3 3 C3 3 C4 4 C4 4 A1 A1 A2 P2 A2 P2 A3 P3 A3 P3 A4 P4 A4 P4 A5 P5 A5 P5 A6 P6 A6 P6 A7 P7 A7 P7 A8 P8 A8 P8 C1 1 C1 1 C2 2 C2 2 A9 P9 A9 P9 A10 0 A10 0 A11 1 A11 1 A12 2 A12 2 A13 3 A13 3 A14 4 A14 4 A15 5 A15 5 A16 6 A16 6 C3 3 C3 3 C4 4 C4 4 A1 A1 C1 1 C1 1 C2 2 C2 2 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A1 A1 C1 1 C1 1 C2 2 C2 2 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A7 P7 A7 P7 C7 7 C7 7 A8 P8 A8 P8 C8 8 C8 8 A9 P9 A9 P9 C9 9 C9 9 A10 0 A10 0 C10 10 C10 10 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A7 P7 A7 P7 C7 7 C7 7 A8 P8 A8 P8 C8 8 C8 8 A9 P9 A9 P9 C9 9 C9 9 A10 0 A10 0 C10 10 C10 10 A1 A1 A2 P2 A2 P2 A3 P3 A3 P3 A4 P4 A4 P4 A5 P5 A5 P5 A6 P6 A6 P6 A7 P7 A7 P7 A8 P8 A8 P8 C1 1 C1 1 C2 2 C2 2 A1 A1 A2 P2 A2 P2 A3 P3 A3 P3 A4 P4 A4 P4 A5 P5 A5 P5 A6 P6 A6 P6 A7 P7 A7 P7 A8 P8 A8 P8 C1 1 C1 1 C2 2 C Separate Wiring Each input line of the EB3C makes up one independent intrinsically safe circuit. A1 A1 C1 1 C1 1 C2 2 C2 2 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A1 A1 C1 1 C1 1 A2 P2 A2 P2 C2 2 C2 2 A3 P3 A3 P3 C3 3 C3 3 A4 P4 A4 P4 C4 4 C4 4 A5 P5 A5 P5 C5 5 C5 5 A6 P6 A6 P6 C6 6 C6 6 A7 P7 A7 P7 C7 7 C7 7 A8 P8 A8 P8 C8 8 C8 8 A9 P9 A9 P9 C9 9 C9 9 A10 0 A10 0 C10 10 C10 10 Diagram Symbols Serial-Parallel Connection of Switches Contacts in one switch Diagram Symbols (EB9Z-A or EB9Z-A1) Serial-Parallel Connection of Switches Contacts in one switch (EB9Z-A or EB9Z-A1) One intrinsically safe circuit (maximum 16 circuits) One intrinsically safe circuit (maximum 16 circuits) 1 2 A1 C1 C2 1 2 A1 C1 C2 otes As shown in the diagram on the left, the required number of contacts in one switch (3 contacts in the example at left) can be added to the contacts in one switch connected to one input channel. Similarly, a required number of contacts in one switch can be added to a common line connected to multiple input channels. The capacitance and inductance of the added contacts in one switch must be included in the calculation of the wiring capacitance and inductance in Precautions for Operation, 5. Wiring for Intrinsic Safety, (7). In addition, a required number of contacts can be added in the enclosure of contacts in one switch. In this case, however, do not include the capacitance and inductance in the calculation of the wiring capacitance and inductance. Instead, make sure that the internal capacitance (Ci) and internal inductance (i) are within the values shown in the table Switch Explosion-Protection Specifications (Japan only)

11 EB3C Recommended Connector Cable for Connector Types Description o. of Poles ength (m) Part umber Shape Applicable Type I/O Terminal Cable With Shield Without Shield Cable with Crimping Terminal 40-pin Cable for PC FC9Z-H A, FC9Z-H B Internal Connection Fujitsu Connector FC-367J024-AU/F B A (Connection Side) BX9Z-H B Internal Connection Connector A IDEC JE1S Fujitsu Connector FC-367J040-AU/F B A IDEC Connector JE1S C (Connection Side) 0.5 FC9Z-H050A20 1 FC9Z-H100A20 2 FC9Z-H200A20 3 FC9Z-H300A FC9Z-H050B20 1 FC9Z-H100B20 2 FC9Z-H200B20 3 FC9Z-H300B20 1 BX9Z-H100E4 2 BX9Z-H200E4 3 BX9Z-H300E4 1 BX9Z-H100B 2 BX9Z-H200B 3 BX9Z-H300B FC9Z-H E4 Internal Connection IDEC Connector JE1S (Connection Side) Connector B IDEC JE1S (Connection Side) (Connection Side) (Connection Side) Y-shaped Compresion Terminal (Marking Tube o.) Connector B Connector A IDEC MicroSmart I/O Module IDEC MicroSmart I/O Module Screw Terminal Mitsubishi A Series Input Module (positive common) EB3C-T16CKD-C OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 251

12 EB3C Communication Sensors Power Supplies Automation Software PCs OI Touchscreens Installing the EB3C Intrinsically Safe 1. The EB3C can be installed in any direction. 2. Install the EB3C intrinsically safe barrier in a safe area (non-hazardous area) in accordance with intrinsic safety ratings and param eters. To avoid mechanical shocks, install the EB3C in an enclosure which suppresses shocks. 3. When installing or wiring the EB3C, prevent electromagnetic and electrostatic inductions in the intrinsically safe circuit. Also prevent the intrinsically safe circuits from contacting with another intrinsically safe circuit and any other circuits. Maintain at least 50mm clearance, or provide a metallic separating board between the intrinsically safe circuit and non-intrinsically safe circuit. When providing a metallic separating board, make sure that the board fits closely to the enclosure (top, bottom, and both sides). Allowable clear ance between the enclosure and board is 1.5mm at the maximum. The clearance of 50mm between the intrinsically safe cir cuit and non-intrinsically safe circuit may not be sufficient when a motor circuit or high-voltage circuit is installed nearby. In this case, provide a wider clearance between the circuits referring to 5 (3) Minimum Parallel Distance between the Intrinsically Safe Circuit and Other Circuits. 4. In order to prevent contact between intrinsically safe circuits and non-intrinsically safe circuits, mount EB3C units with terminals arranged in the same direction. on-intrinsically Safe Circuit EB3C EB3C EB3C Intrinsically Safe Circuit 5. Maintain at least 6mm (or 3mm according to IEC : 1999) clearance between the terminal of an intrinsically safe circuit and the grounded metal part of a metal enclosure, and between the relay terminal block of an intrinsically safe circuit and the grounded metal part of a metal enclosure. 6. For installing the EB3C, mount on a 35mm-wide DI rail or directly on a panel using screws. Make sure to install securely to withstand vibration. When mounting on a DI rail, push in the clamp completely. Use the B6 end clips on both sides of the EB3C to prevent from moving sideways. 7. Excessive extraneous noise may cause malfunction and damage to the EB3C. When extraneous noise activates the voltage limiting circuit (thyristor), remove the noise source and restore the power. Terminal Wiring 1. Using a ø5.5mm or smaller screw driver, tighten the termi nal screws (including unused terminal screws) to a torque of 0.6 to 1.0 m (recommended value). 2. Make sure that IP20 is achieved when wiring. Use insulation tubes on bare crimping terminals. 3. To prevent disengaged wires from contacting with other intrinsically safe circuits, bind together the wires of one intrinsically safe circuit. 4. When the adjacent terminal is connected to another intrinsi cally safe circuit, provide an insulation distance of at least 6mm. Switches in the Hazardous Area 1. A switch contains the switch contact, enclosure, and internal wiring. A switch contact refers to an ordinary switching device which consists of contacts only, such as a pushbut ton switch. See below. EB3C EB3C Intrinsically Safe Circuit Applicable Switches Control Switches Sensing Switches ote: Push-pull Switches Twisting Switches ever and Slide Switches Displacement Switches Pushbutton, Foot, Trigger, Rocker, Grip Rotary, Selector, Cam, Drum, Thumb wheel Toggle, Multidirectional, Wobble stick, ever, Slide switch Microswitch, imit, Magnetic proximity, Door, Reed, Mercury iquid level Pressure, Temperature evel Switches Others For installation in hazardous areas and connection to the EB3C, use switches which are certified, approved, or considered to be simple apparatus in relevant standards in each country. 2. When the switch has internal wiring or lead wire, make sure that the values of internal inductance (i) and capacitance (Ci) are within the certified values. 3. Enclose the switch contact s bare, live part in an enclosure of IP20 or higher protection. 4. Depending on the explosion-protection specifications according to TIIS, the exposed area of the plastic switch opera tor is limited as follows: Exia II CT6 (EB9Z-A): 20cm 2 maximum Exia II BT6 (EB9Z-A1): 100cm 2 maximum 5. Attach the certification mark supplied with the EB3C on the EB9Z-A or EB9Z- A1 switch (for Japanese applications). 6. When the switch operator of the plastic enclosure has a wider exposed area than the following limits, attach a caution label. II C: 20 cm 2 maximum II B: 100 cm 2 maximum Caution To prevent electrostatic charges, do not rub the switch surface during operation. Use a soft cloth dipped with water for cleaning. Caution abel Example 7. For the 1-circuit separate wiring, a resistor to prevent reed switch contact welding and an ED miniature pilot light can be connected in series with the contact. See below. Use the terminal screw of M3 or larger. Applicable Resistor Ratings Resistance 100Ω maximum Rated Wattage 0.5 to 3W Type Metal (oxide) film resistors R Reed Switch Terminal Block EB3C I series ED miniature pilot lights Output Specifications 1. When wiring the output from the EB3C, connect the non-intrinsically safe circuit to terminals A and C. The EB3C out put circuit is not equipped with short-circuit protection. If required, provide a protection in the external circuit. 2. Relay Output Some types of loads generate reverse emf (such as sole noids) or cause a large inrush current (incandescent lamps), resulting in a shorter operation life of output relay contacts. The operation life of contacts can be extended by preventing the reverse emf using a diode, RC, or varistor, or by suppressing the inrush current using a resistor or R. Contacts are made of gold-clad silver. When using at a small current and a low voltage (reference value: 0.1mA, 0.1V), test the contact on the actual circuit in advance

13 EB3C 3. Transistor Output When connecting a small load, the load may not turn off because of a leakage current, even though the transistor output is turned off. If this is the case, connect a resistor in parallel with the load to bypass the leakage current. When an excessively high voltage (clamps at 33V, 1W) or a reverse voltage is applied to the output terminals, the clamping circuit or output transistor may be damaged. When driving an inductive load, be sure to connect a diode across the load to absorb reverse emf. Cn *: Surge Absorber Example of Overvoltage Absorption Circuit 4. In the common wiring only types, the output terminals are not isolated from each other. 5. When connecting the connector type EB3C s in parallel, use one power supply to power the EB3C s. Do not connect any wiring to the C1 and C2 terminals. Wiring for Intrinsic Safety 1. The voltage applied on the general circuit connected to the non-intrinsically safe circuit terminals of the EB3C relay bar rier must be 250V AC, 50/60Hz, or 250V DC at the maxi mum under any conditions, including the voltage of the input power and the internal circuit. 2. When wiring, take into consideration the prevention of elec tromagnetic and electrostatic charges on intrinsically safe circuits. Also, prevent intrinsically safe circuits from contact ing with other circuits. 3. The intrinsically safe circuits must be separated from non-intrinsically safe circuits. Contain intrinsically safe circuits in a metallic tube or duct, or separate the intrinsically safe cir cuits referring to the table below. ote: Cables with a magnetic shield, such as a metallic sheath, prevent electromagnetic induction and electrostatic induction, however, a non-magnetic shield prevents electrostatic induction only. For non-magnetic shields, take a preventive measure against electro magnetic induction. Finely twisted pair cables prevent electromagnetic induc tion. Adding shields to the twisted pair cables provides pro tection against electrostatic induction. Minimum Parallel Distance between the Intrinsically Safe Circuit and Other Circuits (mm) Voltage and Current of Other Circuits An Over 100A * 100A or less 50A or less 10A or less Over 440V V or less V or less V or less V or less When identifying intrinsically safe circuits by color, use light blue terminal blocks and cables. 5. When using two or more EB3C s to set up one intrinsically safe circuit in the common wiring configuration, interconnect two neutral terminals (1 through 10) on each EB3C between adjacent EB3C s in parallel. 6. Make sure that the power of the EB3C and contact are turned off before starting inspection or replacement. 7. When wiring the intrinsically safe circuit, determine the dis tance to satisfy the wiring parameters shown below. ote that parameters are different between separate wiring and common wiring. a. Wiring capacitance Cw Co (Ci + 2 nf) Co: Maximum external capacitance of the EB3C Ci: Internal capacitance of the switch : The number of switches connected in series or parallel (the number is infinite) b. Wiring inductance w o (i + 5 µh) o: Maximum external inductance of the EB3C i: Internal inductance of the switch : The number of switches connected in series or parallel (the number is infinite) c. Wiring resistance Rw Rw: Allowable wiring resistance d. Allowable wiring distance D (km) is the smallest value of those calculated from the capacitance, inductance, and resistance. D Cw/C C (nf/km): Capacitance of cable per km D w/ (mh/km): Inductance of cable per km D Rw/2R R (Ω/km): Resistance of cable per km ote: For the details of wiring the intrinsically safe circuits, refer to a rel evant test guideline for explosion-proof electric equipment in each country. 8) Applicable Wire Size 0.5 to 2.0mm 2 (AWG20 to AWG14): two wires However, one wire for 2.0 mm 2 (AWG14) Mounting Bracket The following mounting brackets can be used to install the EB3C relay barriers and EB3 lamp barriers on the mounting holes of IBRC contact signal transducer, IBP pilot relay barrier, and IBZ buzzer. o. of Channels Part o. Dimension (mm) A B C 1 EB9Z-K EB9Z-K EB9Z-K EB9Z-K EB9Z-K EB9Z-K Dimensions C B A ø5 (four) M4 (two or four) : EB9Z-K10 only 7 All dimensions in mm. OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 253

14 EB3 EB3 Discrete Input Barrier with Redundant Output Communication Sensors Power Supplies Automation Software PCs OI Touchscreens Build a safety system in an explosive atmosphere. Key features: Safety Performance Performance level e Category 4 [Exia] II C Ensures safety and machine safety in an explosive atmosphere Machine safety system can be built in compliance with ISO Category 4, Performance level e. Safety input devices applicable in any explosive gas and hazardous areas are available. Available with auxiliary inputs (5 points) used to monitor the operating status of safety input devices Global usage USA (U), Global IEC-Ex, Europe (ATEX), Japan (TIIS), China (CQST) Machine safety: TÜV Rheinland o grounding required Entity Barrier Parameters Ta= 60 C, Um= 250V, (Um=125V U only), Uo=13.2V, Io= 14.2mA, Po= 46.9mW at each channel Pn-n Io=227.2mA, Po= 750mW at max 16 channels Pn-n Io(mA) Combined Po(mW) o(mh) TIISI only Ta=60 C, Um=250V 1 ch Seperate 5 ch Common Uo 13.2V 13.2V Co(μF) Io 14.2mA 227.2mA Po 46.9mW 750mW Co 0.47μF 0.28μF ote 1 Added to above table, the next values combined o and Co are allowable; o 87.5mH 0.56mH Io(mA) o(mh) 175* * * Co(µF) 0.90* * * ote 2 The intrinsic safe apparatus and wirings shall be accordance to following formulas; for example: Ui Uo Ii Io Pi Po Ci+Cc Co i+c o *: Therefore, the values are allowable only at i 1%o and Ci 1%Co of the intrinsic safe apparatus. (In the case of 50% of Co and o parameters are applicable,the maximum capacitance allowed shall not be more than Co = 1 µf for IIB and Co= 600 nf for IIC.) Discrete Input Barrier with Redundant Output 2 2O Without Without 2 2O 5 (1 common) 5O (1 common) Auto reset (Auto start) Manual reset (Manual start) Auto reset (Auto start) Manual reset (Manual start) EB3-A2D EB3-M2D EB3-A2R5D EB3-M2R5D 1. A maximum of five monitor contacts from safety input devices can be connected to the auxiliary input terminals. In addition, non-safety input devices can also be connected to the auxiliary input terminals. 2. On auto reset (auto start) models, when the safety condition is met (two safety inputs are both on), safety outputs are turned on automatically. Connect the reset (start) input terminals Y1 and Y2 together except for the following cases: When connecting a contactor or force guided relay to the safety output of the EB3, connect the C contacts of the contactor or force guided relay to the reset (start) input terminals Y1 and Y2 of the EB3 for use as a backcheck input signal. 3. On manual reset (manual start) models, while the safety condition is met (two safety inputs are both on), safety outputs are turned on at the falling edge of the reset switch (start switch) signal (OFF O OFF) (start off check). Manual reset (manual start) models have a monitoring function of reset switch contacts (detection of welded contacts). Use O contacts of a momentary switch for the reset (start) input. When connecting a contactor or force guided relay to the safety output of the EB3, connect the C contacts of the contactor or force guided relay to the reset (start) input terminals Y1 and Y2 of the EB3 for use as a backcheck input signal

15 EB3 Selection Guide 1. Selecting the reset (start) function Auto reset (auto start): Select this model when connecting safety control devices, such as safety relay modules or safety controllers, to the EB3 safety outputs to set up a safety system, using the reset (start) function of the safety control device. Select this model when connecting contactors or force guided relays to the EB3 safety outputs to set up a safety system, and a risk assessment on the entire system has not found any safety problem in using auto reset (auto start). Manual reset (manual start): Select this model when connecting contactors or force guided relays to the EB3 safety outputs to set up a safety system, and a risk assessment on the entire system has found that manual reset (manual start) is necessary. 2. Selecting the auxiliary outputs Without auxiliary outputs: Select this model when the operating status of safety input devices are not monitored. With auxiliary outputs: Select this model when the operating status of safety input devices are monitored or when non-safety input devices are also connected. Specifications EB3 General Specifications Rated Power Voltage 24V DC EB3 Safety Specifications Category 4 Power Voltage Range 20.4 to 26.4V DC Performance evel (P) e 20 to +60 C (no freezing) Mean Time to Dangerous Failure (MTTFd) 100 years Operating Temperature U: 20 to +40 C (no freezing) Diagnostic Range 99% minimum Operating Humidity 45 to 85% RH Calculation conditions for MTTFd (no condensation) t cycle : Mean operation cycle = 1 hour h Power Without auxiliary output 5.5W maximum op : Mean operation hours per day = 24 hours d op : Mean operation days per year = 365 days Consumption With auxiliary output 7.0W maximum ote: When t cycle is shorter than 1 hour, MTTFd will decrease Contacts 13-14, O Resistive 30V DC, 1A Safety Rated Inductive DC-13, 24V, 1A Output Response Turn on 100 ms maximum (rated voltage) Turn off 20 ms maximum Contacts A* - C1 5O/1 common Auxiliary Output Mounting Rated Response (rated voltage) *: Channel umbers: 1 to 5 Resistive Turn on Turn off 24V DC, 3A, common terminal 5A max. 15 ms maximum 10 ms maximum DI rail or panel mounting EB3 Certifications Certification Organization Ratings Certification umber U Class I, Zone 0, [AExia] II C Class I, II, III, Div. 1, Groups A, B, C, D, E, F and G E PTB (IEC-Ex) [Exia] II C, [Exia D] IEC Ex PTB PTB (ATEX) II (1) G [Exia] II C II (1) D [Exia D] PTB 09 ATEX 2046 Discrete Input with Redundant Output [Exia] II C TC18753 TIIS Switch (EB9Z-A) Exia II CT6 TC15758 Switch (EB9Z-A1) Exia II BT6 TC15961 CQST [Exia] IIC CEx OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 255

16 EB3 Dimensions (mm) OI Touchscreens EB3-A2D EB3-M2D 65.0 EB3-A2R5D EB3-M2R5D Terminal Functions 24V DC Power Y1-Y2 Reset input (Start input) Safety input Safety input 2 1, 2 Signal ground P*-3 Auxiliary input PCs Mounting Hole ayout EB3-A2D EB3-M2D EB3-A2R5D EB3-M2R5D Safety output Safety output 2 A*-C1 Auxiliary output *: 1 to 5 2-M4 tapped or 2-ø4.5 drilled holes 65 2-M4 tapped or 2-ø4.5 drilled holes 65 Automation Software Power Supplies Sensors 51 EB3 System Configuration Examples 1:1 connection with a safety input device, compliant with Category 4 Safety Input Device Safety Input Device EB3-A2D EB3-M2D 97 Barrier Safety Output Barrier Safety Output Safety Control Device Safety Contactor Safety Control Device PC Safety Contactor PC Safety Output Backcheck Input Safety Contactor Connection with multiple safety input devices, capable of monitoring up to 5 contact operations, compliant with Category 3 For monitoring operating statuses of safety input devices located in a non-hazardous area Safety Input Devices Connected in Series Safety Input Devices Connected in Series Hazardous Area Hazardous Area Monitor on-hazardous Area on-hazardous Area EB3-A2R5D EB3-M2R5D Backcheck Input Reset (Start) Input Barrier Safety Output Auxiliary Output (Monitor Output) Barrier Safety Output Backcheck Input Reset (Start) Input Reset (Start) Input Safety Output Backcheck Input Reset (Start) Input Safety Contactor A safety relay module or safety controller is used to set up a safety circuit, using the reset (start) function of the safety relay module or safety controller. The reset (start) function is used to set up a safety circuit, without using a safety relay module or safety controller. Communication A safety relay module or safety controller is used to set up a safety circuit, using the reset (start) function of the safety relay module or safety controller. The manual reset (manual start) function of the EB3 is used to set up a safety circuit, without using a safety control device. Monitor Auxiliary Output (Monitor Output) 256

17 EB3 Installing a reset switch in a hazardous area, using auxiliary input and output Safety Input Devices Reset (Start) Switch Other Input Device Safety Input Devices Reset (Start) Switch Other Input Device Hazardous Area on-hazardous Area EB3-A2R5D EB3-M2R5D Barrier Safety Output Reset (Start) Output Other Output Barrier Safety Output Backcheck Input Reset (Start) Input Other Output Safety Control Device PC Safety Contactor PC Safety Output Backcheck Input Safety Input Devices Connectable to Safety Input Terminals (Examples) Emergency stop switch: Safety switch: otes for Operation (on-illuminated) XW1E-BV402M-R, X4E-B412MRH HS6B-02B05, HS1B-02R 1. Do not disassemble, repair, or modify the EB3 discrete input barrier with redundant output, otherwise the safety characteristics may be impaired. 2. Use the EB3 within its specification values. 3. The EB3 can be mounted in any direction. 4. Mount the EB3 on a 35-mm-wide DI rail or directly on a panel surface using screws. When mounting on a DI rail, push in the clamp and use end clips to secure the EB3. When mounting on a panel surface, tighten the screws firmly. 5. Excessive noise may cause malfunction or damage to the EB3. When the internal voltage limiting circuit (thyristor) has shut down the power due to noise, remove the cause of the noise before powering up again. 6. The internal power circuit contains an electronic fuse to suppress overcurrents. When the electronic fuse has tripped, shut down the power, remove the cause of the overcurrent before powering up again. 7. Use crimping terminals with insulation sheath for wiring. Tighten the terminal screws, including unused terminal screws, to a recommended tightening torque of 0.6 to m using a screwdriver of ø5.5 mm in diameter. 8. Before inspecting or replacing the EB3, turn off the power. Safety Contactor Instructions otes for Machine Safety 1. Operate the safety input device to check the EB3 functionality everyday. 2. For safety input devices, such as safety switches or emergency stop switches, connected to the EB3, use safety standard-compliant devices with direct opening action and 2C contacts. 3. Do not use the auxiliary input as a safety input. 4. For safety control devices connected with the EB3, use machine safety standard-compliant devices with a disparity detection function. 5. Use safety inputs and safety outputs in a circuit configuration compliant with safety requirements. 6. To calculate the safety distance, take into consideration the response time of all devices comprising the system, such as the EB3 and safety devices connected to the EB3. 7. Separate the input and output wiring from power lines and motor lines. 8. When using multiple EB3 discrete input barriers with redundant output, do not connect one switch to more than one EB3. Use separate switches for each EB3. 9. To ensure EMC, use shielded cables for safety inputs and auxiliary inputs. Connect the shield to the FG of the control panel on which the EB3 is mounted. 10. For protection against overcurrents, connect an IEC compliant 2A fast-blow fuse (5 20 mm). 11. Evaluate the ISO category and performance level in consideration of the entire system. OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 257

18 EB3 Sensors Power Supplies Automation Software PCs OI Touchscreens Safety otes 1. Install the EB3 in an enclosure capable of protecting against mechanical shocks at a hazardous location in accordance with intrinsic safety ratings and parameters. 2. Install and wire the EB3 so that the EB3 is not subject to electromagnetic and electrostatic induction and does not contact with other circuits. For example, keep a minimum spacing of 50 mm between intrinsically safe and non-intrinsically safe circuits, or provide a metallic separating board between the intrinsically safe circuit and non-intrinsically safe circuit. When providing a metallic separating board, make sure that the board fits closely to the enclosure (top, bottom, and both sides). Allowable clearance between the board and the enclosure is 1.5 mm at the maximum. When a motor circuit or high-voltage circuit is installed nearby, keep a wider spacing than 50 mm between intrinsically safe and non-intrinsically safe circuits. 3. Keep a minimum spacing of 3 mm between the terminal or relay terminal block of the intrinsically safe circuit and the grounded metal parts of the metal enclosure. 4. Connect the terminals so that IP20 is ensured. 5. To prevent disengaged wires from contacting with other intrinsically safe circuits, bind together the end of wires. 6. Make sure that the voltage of the power supply for the devices connected to the non-intrinsically safe circuit or the internal voltage of such devices does not exceed 250V AC/DC 50/60 Hz (U rating: 125V AC 50/60 Hz) or 250V DC (U rating: 200V DC) under any normal and abnormal conditions. 7. Make sure that the wiring of intrinsically safe circuits does not contact with other circuits or is not subject to electromagnetic and electrostatic inductions, otherwise protection from hazards is not ensured. 8. When identifying intrinsically safe circuits by color, use light blue terminal blocks and cables. 9. When wiring the intrinsically safe circuit, determine the distance to satisfy the wiring parameters shown below. a) Wiring capacitance Cw Co Ci Co: Intrinsically safe circuit allowable capacitance Ci: Internal capacitance of switches b) Wiring inductance w o i o: Intrinsically safe circuit allowable inductance i: Internal inductance of switches c) Wiring resistance Rw Rw: Allowable wiring resistance Switches in the Hazardous Area 1. A switch contains the switch contact, enclosure, and internal wiring. A switch contact refers to an ordinary switching device which consists of contacts only. 2. When the switch has internal wiring or lead wire, make sure that the values of internal capacitance (Ci) and inductance (i) are within the certified values. 3. Enclose the bare live part of the switch contact in an enclosure of IP20 or higher protection. Communication 258

19 EB3 EB3 Discrete Output 126 types of pilot lights and buzzers can be connected. Illuminated pushbuttons and illuminated selector switches can be connected by combining with the EB3C discrete input barrier. o grounding required. Key features: Discrete Output Barrier Pilot ight (separate wiring) Pilot ight (common wiring) Illuminated Pushbutton Illuminated Selector Switch Buzzer (separate wiring) Ratings [Exia] II C Exia II CT6 Exia II CT4 Exia II CT4 Exia II CT4 Exiab II CT6 IEC60079 compliant Compact and lightweight 8- and 16-channel types are available in common wiring types, ideal for connection to PCs. 16-circuit types are also available with a connector. Universal AC power voltage (100 to 240V AC or 24V DC power [U rating: 100 ~ 120V AC]) o grounding required IDEC s original spring-up terminal minimizes wiring time. Installation, 35-mm-wide DI rail mounting or direct screw mounting ø6, ø8, ø10, ø22 and ø30 pilot lights available Illuminated pushbuttons and illuminated selector switches can be connected by combining with the EB3C discrete input barrier. Illumination colors: Amber, blue, green, red, white, and yellow (pushlock turn reset type: red only) Continuous and intermittent sound types are available for buzz ers (ø30). Global usage USA: U/FM Europe: CE marking Global: IECEx, ATEX Japan: TIIS China: CQST Korea: KCs Ship class: K (Japan), KR (Korea) ISTED FM APPROVED Illuminated Pushbutton/Selector Switches Illuminated pushbutton/selector switches can be used with the combination of EB3C and EB3. Spring-up Fingersafe Terminals Reduce Wiring Time Entity Barrier Parameters Ta= 60 C, Um= 250V, (Um=125V U only), Uo=13.2V, Io= 14.2mA, Po= 46.9mW at each channel Pn-n Io=227.2mA, Po= 750mW at max 16 channels Pn-n Io(mA) Combined Po(mW) o(mh) Finger-safe TIIS, K only Ta=60 C, Um=250V 1 ch Seperate 16 ch Common Uo 13.2V 13.2V Co(μF) Io 14.2mA 227.2mA Po 46.9mW 750mW Co 0.47μF 0.365μF ote 1 Added to above table, the next values combined o and Co are allowable; o 87.5mH 0.425mH Io(mA) o(mh) 175* * * Co(µF) 0.90* * * ote 2 The intrinsic safe apparatus and wirings shall be accordance to following formulas; for example: Ui Uo Ii Io Pi Po Ci+Cc Co i+c o *: Therefore, the values are allowable only at i 1%o and Ci 1%Co of the intrinsic safe apparatus. (In the case of 50% of Co and o parameters are applicable,the maximum capacitance allowed shall not be more than Co = 1 µf for IIB and Co= 600 nf for IIC.) Common Wiring for PC Inputs 8- and 16-circuit types are available in common wiring types, ideal for connection to PCs (DC voltage only). Connector Type MI connector on the non-hazardous side Easy connection to PCs Wiring is reduced by 90% Various 20-pin MI connectors can be connected. OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 259

20 EB3 Sensors Power Supplies Automation Software PCs OI Touchscreens Electrical Specifications Ratings Degree of Protection Discrete Output Barrier Installation ocation Pilot ight, Illuminated Switch, Buzzer on-intrinsically Safe Circuit Maximum Voltage (Um) Intrinsic safety type (IEC compliant) [Exia] II C IP20 (IEC60529) Safe indoor place (non-hazardous area) For zone 0, 1, 2 hazardous areas For zone 1 and 2 hazardous areas Specifications General Specifications Communication 250V AC 50/60Hz, 250V DC U value: 125V AC Operation Input O, Output O (1:1) Certifications Certification Ratings Organization Class I, II, III Div. 1 U Group A, B, C, D, E, F, and G Class I, Zone 0 [AExia] II C Class I, II, III Div. 1 FM Group A, B, C, D, E, F, and G Class I, Zone 0 [AExia] II C E Certification o. PTB (IEC-Ex) [Exia] IIC: Gas vapor IECEx PTB PTB (ATEX) TIIS K II(1)G [Exia] IIC: Gas vapor II(1)D [Exia] IIIC: Dust Discrete output barrier: [Exia] II C Pilot light/miniature pilot light: (separate wiring): Exia II CT6 Pilot light/miniature pilot light: (common wiring): Exia II CT4 Illuminated switch: Exia II CT4 Buzzer: Exib II CT6 Discrete output barrier: [Exia] II C Buzzer: Exib II CT6 PTB09 ATEX2046 TC20541 TC16361 TC16360 TC16362 TC20797 Type Test o. 13T606 pending CQST [Exia Ga] IIC CEx KCs Discrete output barrier: [Exia] II C Buzzer: Exib II CT6 KR [Exia] IIC pending KCS14-AV4BO-0375 pending Power Voltage Type AC Power DC Power Rated Power Voltage 100 to 240V AC (U rating: 100 ~ 120V AC) 24V DC Allowable Voltage Range 85 to 264V AC (U rating: 85 ~ 125V AC) 21.6 to 26.4V DC Rated Frequency 50/60 Hz (allowable range: 47 to 63 Hz) Inrush Current 10A (100V AC) 20A (200V AC) 10A Dielectric Strength (1 minute, 1 ma) Operating Temperature Storage Temperature Operating Humidity Atmosphere Pollution Degree Insulation Resistance Vibration Resistance (damage limits) Shock Resistance (damage limits) Terminal Style Mounting Power Consumption (approx.) Between intrinsically safe circuit and non-intrinsically safe circuit: V AC Between AC power and signal input: 1500V AC 20 to +60 C (no freezing) 20 to +60 C (no freezing) 45 to 85% RH (no condensation) 800 to 1100 hpa 2 (IEC60664) 10 MΩ minimum (500V DC megger, between the same poles as the dielectric strength) Panel mounting: 10 to 55 Hz, amplitude 0.75 mm (2 hours each on X, Y, Z) DI rail mounting: 10 to 55 Hz, amplitude 0.35 mm (2 hours each on X, Y, Z) Panel mounting: 500 m/s 2 (3 times each on X, Y, Z) DI rail mounting: 300 m/s 2 (3 times each on X, Y, Z) M3 screw terminal 35-mm-wide DI rail or panel mounting (M4 screw) 8.8 VA (EB3-S10SA at 200V AC) 5.2 W (EB3-S16CSD at 24V DC) ote: Illuminated switches, pilot lights, and miniature pilot lights are certified by TIIS and K only. Other certification organizations, such as U, regard these units as simple apparatus, and require no certification

21 EB3 Discrete Output Power Voltage 100 to 240V AC (U rating: 100 ~ 120V AC) 24V DC Accessories Connection to on-intrinsically Safe Circuit Screw Terminal Screw Terminal Connector Input Source Sink Source Sink ame Part umber Description DI Rail BAA1000 BA000 Part umbers Input Wiring Method Separate/Common Wiring Compatible umber of Channels Part umber Weight (g) 1 EB3-S01SA EB3-S02SA EB3-S03SA EB3-S05SA EB3-S06SA EB3-S08SA EB3-S10SA 360 Common Wiring Only 8 EB3-S08CSA 260 Separate/Common Wiring Compatible 1 EB3-S01KA EB3-S02KA EB3-S03KA EB3-S05KA EB3-S06KA EB3-S08KA EB3-S10KA 360 Common Wiring Only 8 EB3-S08CKA 260 Separate/Common Wiring Compatible Common Wiring Only Separate/Common Wiring Compatible Common Wiring Only 1 EB3-S01SD EB3-S02SD EB3-S03SD EB3-S05SD EB3-S06SD EB3-S08SD EB3-S10SD EB3-S08CSD EB3-S16CSD EB3-S01KD EB3-S02KD EB3-S03KD EB3-S05KD EB3-S06KD EB3-S08KD EB3-S10KD EB3-S08CKD EB3-S16CKD 350 Source 16 EB3-S16CSD-C 350 Common Wiring Only Sink 16 EB3-S16CKD-C 350 Aluminum (1m long, 10.5mm high) Steel (1m long, 7.5mm high) End Clip B6 Medium DI rail end clip OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 261

22 EB3 OI Touchscreens Internal Circuit Block Diagram AC Power Source Input 1 P2 2 P3 3 DC Power Sink Input 1 P2 2 P3 3 Connector Wiring Source Input Hazardous Area on-hazardous Area Green Yellow Yellow Yellow Green Yellow Yellow Yellow Green Yellow Yellow PCs ~ S1 C1 S2 C2 S3 C3 ~ + S1 C1 S2 C2 S3 C3 + ~ S1 S16 C1 C2 Dimensions (mm) Automation Software Terminal EB3 S01 EB3 S02 EB3 S03 EB3 S05 EB3 S06 EB3 S08C EB3 S08 EB3 S10 EB3 S16C Intrinsic Safety Side: ight Blue ø4.4 Power Supplies ø6 hole Communication on-intrinsic Safety Side: Yellow (4) Sensors Mounting Hole Hole ayout ayout (Screw (Screw Mounting) Mounting) 2-M4 tapped or 2-ø4.5 mounting holes 65 2-M4 tapped or 2-ø4.5 mounting holes 2-M4 tapped or 2-ø4.5 mounting holes 4-M4 tapped or 4-ø4.5 mounting holes

23 EB3 Connector (4) 6 EB3 S16C D ø ø4.5 holes 65 on-intrinsically Safe External Input Wiring Examples 6-channel Source 8-channel Common Wiring, Source (Ex.: EB3-S06SA) (Ex.: EB3-S08CSD) 100 to 240V AC 1 P2 2 P3 3 P4 4 P5 5 P S1 C1 S2 C2 S3 C3 S4 C4 S5 C5 S6 C6 16-channel Common Wiring, Source (Ex.: EB3-S16CSD) + 24V DC P2 P3 P4 P5 P6 P7 + 24V DC P8 1 2 P S1 S2 S3 S4 S5 S6 S7 S8 C1 C2 S9 S10 S11 S12 S13 S14 S15 S16 C3 C4 ote: Source input type can be connected to PC sink output type C terminal is the negative common line. All dimensions are in mm 4-M4 or 4-ø4.5 holes 97 Mounting Hole ayout P2 P3 P4 P5 P6 P7 P S1 S2 S3 S4 S5 S6 S7 S8 C1 C channel Common Wiring, Sink (Ex.: EB3-S16CKD) + 24V DC P2 P3 P4 P5 P6 Applicable Crimping Terminal 6 max. 3 max. ø3.2 min. 5.4 min. Solid Wire - Strip wire end 6 to 8 mm Stranded Wire - use a ferrule 6-channel Sink (Ex. EB3-S06KA) 100 to 240V AC P7 1 6 to 8 mm P2 2 P3 3 P4 4 P5 5 P S1 C1 S2 C2 S3 C3 S4 C4 S5 C5 S6 C6 P8 1 2 P S1 S2 S3 S4 S5 S6 S7 S8 C1 C2 S9 S10 S11 S12 S13 S14 S15 S16 C3 C4 ote: Sink input type can be connected to PC source output type C terminal is the positive common line. OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 263

24 EB3 Connector Wiring Terminal Arrangement OI Touchscreens EB3-S16CSD-C CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 S9 S10 S11 S12 S13 S14 S15 S16 C C S1 S2 S3 S4 S5 S6 S7 S8 C1 C2 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 COM +V 1 2 CHn Sn COM + Wiring Example with IDEC s MicroSmart PC Output Modules FC4A-T16K3 EB3-S16CSD-C FC4A-T16S3 EB3-S16CKD-C Terminal Output Input Terminal Terminal Output Input Terminal 20 Q0 S Q0 S Q10 S Q10 S9 19 EB3 PC 18 Q1 S Q1 S2 18 +V (C2) 17 Q11 S Q11 S10 17 PCs Automation Software + Internal Circuit EB3-S16CKD-C S1-S16 COM (C1) Power Supplies Sensors Communication Output Q0-Q15 COM CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 S9 S10 S11 S12 S13 S14 S15 S16 C C S1 S2 S3 S4 S5 S6 S7 S8 C1 C2 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 COM -V Internal Circuit 1 2 CHn Sn COM + 16 Q2 S Q12 S Q3 S Q13 S Q4 S Q14 S Q5 S Q15 S Q6 S Q2 S Q12 S Q3 S Q13 S Q4 S Q14 S Q5 S Q15 S Q6 S7 8 + Internal Circuit EB3 COM (C1) S1-S16 COM Output Q0-Q15 PC Internal Circuit 7 Q16 S Q7 S8 6 5 Q17 S COM COM 4 3 COM C 3 2 +V +V 2 7 Q16 S Q7 S8 6 5 Q17 S COM COM 4 3 COM C 3 2 V V 2 -V (C2) 1 +V C 1 1 V C 1 ote: The wiring in dashed line does not affect the operation of the EB3. Applicable connector is IDEC s JE1S-201. Output power for PC outputs is supplied by the EB3, therefore the PC output does not need an external power supply

25 EB3 Wiring Example of Intrinsically Safe External Outputs 1. Common Wiring (Maximum 16 circuits) (Buzzers cannot be wired in a common line.)* (+) ( ) (+) ( ) P2 S1 S1 S2 P2 S2 P3 S3 P3 S3 P4 S4 P4 S4 P5 S5 P5 S5 P6 S6 P6 S6 S7 S8 S7 S8 C1 C1 C2 2. Separate Wiring (+) ( ) S1 P7 P8 1 2 P C2 S9 S10 S11 S12 S13 S14 S15 S16 C3 C4 P7 P8 1 2 P P2 2 P3 3 C1 S2 C2 S3 S9 S10 S11 S12 S13 S14 S15 S16 C3 C4 C3 (+) ( ) 1 P2 2 P3 3 P4 4 P5 5 P6 6 S1 C1 S2 C2 S3 C3 S4 3. Wiring Illuminated Pushbuttons and Illuminated Selector Switches (A maximum of 16 channels of EB3 and EB3C can be wired to a common line.) (+) ( ) B1 B2 B3 S1 S2 S3 1 P2 2 P3 3 P4 4 P5 5 P6 6 S1 C1 S2 C2 S3 C3 S4 C4 S5 C5 S6 C6 (+) ( ) B1 B2 B3 C4 S5 C5 S1 S6 C6 (+) ( ) (+) ( ) (+) ( ) 1 P2 2 P3 3 S1 S1 C1 C1 S2 C2 S3 C3 1 P2 2 P3 3 1 P2 2 P3 3 P4 4 P5 5 P6 6 P7 7 P8 8 P A1 C1 A2 C2 A3 C3 A4 C4 A5 C5 A6 C6 A7 S2 C7 S2 C2 S3 C3 (+) ( ) (+) ( ) 1 P2 2 P3 3 P4 4 P5 5 P6 6 S1 C1 S2 C2 (+) ( ) S1 1 2 C1 C2 S3 C3 (+) ( ) 1 2 S1 C1 C2 S4 C4 (+) ( ) All output lines are wired to a common line inside the intrinsically safe equipment (one common line per intrinsically safe circuit) - DC input models only. All input lines are wired to a common line outside the intrinsically safe equipment (one common line per intrinsically safe circuit). S5 C5 S6 C6 1 P2 2 P3 3 P4 4 P5 5 P6 6 Each output line of the EB3 makes up one independent intrinsically safe circuit of a pilot light or buzzer. 1 2 S1 C1 C2 S1 C1 1 P2 2 P3 3 P4 4 P5 5 P6 6 P7 7 P8 8 P The following example illustrates the wiring for a total of 10 contacts used by three illuminated pushbuttons (B1 to B3) and three illuminated selector switches (S1 to S3). *This is permitted under TIIS approvals S1 A8 C1 C8 S2 A9 C2 S3 S3 C3 C9 A10 C10 S4 C4 S5 C5 S2 S6 C2 C6 S3 S7 C3 C7 S4 S8 C4 C8 S5 S9 C5 S6 C6 C9 S10 C10 (+) ( ) (+) ( ) 1 P2 2 P3 3 P4 4 P5 5 P6 6 P7 7 P8 8 P S1 C1 S2 C2 S3 C3 S4 C4 S5 C5 S6 C6 S7 C7 S8 C8 S9 C9 S10 C10 1 P2 2 P3 3 P4 4 P5 5 P6 6 P7 7 P8 8 P S1 C1 S2 C2 S3 C3 S4 C4 S5 C5 S6 C6 S7 C7 S8 C8 S9 C9 S10 C10 (+) ( ) (+) ( ) When using two or more EB3 s to set up one intrinsically safe circuit in the common wiring configuration, interconnect two neutral terminals (1 through 10) on each EB3 between adjacent EB3 s in a parallel. Diagram Symbols S1 S1 P2 S2 P2 S2 P3 S3 P3 S3 P4 S4 P4 S4 EB3P consisting of one enclosure P5 S5 P5 S5 P6 S6 P6 S6 One intrinsically safe circuit P7 S7 P7 S7 P8 1 2 S8 C1 S8 C1 C2 P8 1 2 One intrinsically safe circuit is a connection consisting of one or more illuminated units connected to a common line. C2 OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 265

26 EB3 Communication Sensors Power Supplies Automation Software PCs OI Touchscreens Recommended Connector Cable for Connector Types Description o. of Poles ength (m) Part umber Shape Applicable Type I/O Terminal Cable With Shield Without Shield Cable with Crimping Terminal 40-pin Cable for PC FC9Z-H A, FC9Z-H B Internal Connection IDEC Connector JE1S (Connection Side) FC9Z-H E4 Internal Connection IDEC Connector JE1S (Connection Side) 20 IDEC Connector JE1S (Connection Side) Y-shaped Compresion Terminal (Marking Tube umber) FC9Z-H050A20 1 FC9Z-H100A20 2 FC9Z-H200A20 3 FC9Z-H300A FC9Z-H050B20 1 FC9Z-H100B20 2 FC9Z-H200B20 3 FC9Z-H300B20 1 BX9Z-H100E4 2 BX9Z-H200E4 3 BX9Z-H300E4 1 BX9Z-H100B 2 BX9Z-H200B 3 BX9Z-H300B BX9Z-H B Internal Connection Connector A IDEC JE1S Fujitsu Connector FC-367J040-AU/F B A Connector B Connector A Connector B IDEC JE1S IDEC MicroSmart I/O Module IDEC MicroSmart I/O Module Screw Terminal Mitsubishi A Series Output Module (sink) EB3-S16CSD-C 266

27 Switches and Pilot Devices Switches and Pilot Devices General Specifications for Pilot ight, Illuminated Pushbutton, Illuminated Selector Switch, and Buzzer Operating Temperature Operating Humidity Dielectric Strength (1 ma, 1 minute) Insulation Resistance Pilot ight and Miniature Pilot ight Degree of Protection ens/illumination Color Intrinsic Safety Ratings and Parameters 20 to +60 C (no freezing) 45 to 85% RH (no condensation) EB3P: 1000V AC I: 500V AC (between intrinsically safe circuit and dead parts) 10 MΩ minimum (500V DC megger, between the same poles as the dielectric strength) IP65 (IEC60529) (except for terminals) EB3P-U/I: IP40 Pilot light: Amber, blue, green, red, white, yellow Miniature pilot light: Amber, green, red, white, yellow 1-channel Separate Wiring Maximum input voltage (Ui): 13.2V Maximum input current (Ii): 14.2 ma Maximum input power (Pi): 46.9 mw Internal capacitance (Ci): 2 nf Internal inductance (i): 5 µh 16-channel Common Wiring Maximum input voltage (Ui): 13.2V Maximum input current (Ii): ma Maximum input power (Pi): 750 mw Internal capacitance (Ci): 32 nf Internal inductance (i): 80 µh ote: Connect buzzers in separate wiring. Buzzers cannot be used in com mon wiring. Illuminated Switch Buzzer Degree of Protection Illumination Color Contact Voltage/Current Intrinsic Safety Ratings and Parameters IP65 (IEC60529) (except for terminals) EB3P-SAW**: IP54 Amber, blue, green, red, white, yellow 12V DC ±10%, 10 ma ±20% (when connecting to the EB3C) 16-channel Common Wiring Maximum input voltage (Ui): 13.2V Maximum input current (Ii): ma Maximum input power (Pi): 750 mw Internal capacitance (Ci): 32 nf Internal inductance (i): 80 µh IP20 (IEC60529) (except for terminals) Degree of Protection Sound Volume 75 db minimum (at 1 m) Sound Source Piezoelectric oscillator (continuous or intermittent) 1-channel Separate Wiring Maximum input voltage (Ui): 13.2V Intrinsic Safety Maximum input current (Ii): 14.2 ma Ratings and Maximum input power (Pi): 46.9 mw Parameters Internal capacitance (Ci): 260 nf Internal inductance (i): 80 mh Weight Part umbers for Pilot ights, Illuminated Pushbuttons, Illuminated Selector Switches, and Buzzers Unit Size Series 1 Shape Operation Mode Contact Ordering umber Pilot ight Miniature Pilot ight ø30 ø22 ø10 ø8 ø6 TW HW W UP Dome EB3P-A1-* Square EB3P-U3B-* Rectangular w/metal Bezel EB3P-U4-* Dome w/diecast Sleeve EB3P-AD1-* Flush EB3P-AW1-* Flush(Marking Type) EB3P-AW1B-* Dome EB3P-AW2-* Square Flush (Marking Type) EB3P-UW1B-* Round Flush EB3P-HW1-* Dome EB3P-HW2-* Square Flush EB3P-HW4-* Round EB3P-W1-* Square EB3P-W2-* Round w/ Square Bezel EB3P-W3-* Extended I-18-* Dome I-19-* Flush I-87-* Extended I-88-* Dome I-89-* Flush I-67-* Extended I-68-* Dome I-69-* 100g ens Color/ Illumination Color Code* A: Amber G: Green R: Red S: Blue W: White 5 Y: Yellow A: Amber G: Green R: Red W: White 5 Y: Yellow Operation OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 267

28 Switches and Pilot Devices OI Touchscreens Part umbers for Pilot ights, Illuminated Pushbuttons, Illuminated Selector Switches, and Buzzers, con t Unit Size Series 1 Shape Operation Mode Contact Ordering umber 2 Illumination ens Color/ Color Code* ø30 Extended Momentary 1O-1C EB3P-BA211-* Maintained 1O-1C EB3P-BAO211-* A: Amber G: Green R: Red S: Blue W: White 5 Y: Yellow Operation Communication Sensors Power Supplies Automation Software PCs Illuminated Pushbutton Illuminated Selector Switch 3 Buzzer ø22 TW HW W Mushroom Pushlock Turn Reset 1O-1C EB3P-BAV311-R Red only Extended Momentary 1O-1C EB3P-BAW211-* Maintained 1O-1C EB3P-BAOW211-* A: Amber G: Green R: Red S: Blue W: White 5 Y: Yellow Mushroom Pushlock Turn Reset 1O-1C EB3P-BAVW411-R Red only Round Round Square ø30 Round ø22 TW HW W Round Round ø30 Momentary 1O EB3P-BH1W110-* Maintained 1O EB3P-BHA1W110-* Momentary DPDT EB3P-B1W1C2-* Maintained DPDT EB3P-BA1W1C2-* Momentary DPDT EB3P-B2W1C2-* Maintained DPDT EB3P-BA2W1C2-* 2-position 1O-1C EB3P-SA211-* Maintained 3-position 2O EB3P-SA320-* Maintained 2-position 1O-1C EB3P-SAW211-* A: Amber Maintained G: Green 2-position, return from 1O-1C EB3P-SAW2111-* R: Red Spring return from right right S: Blue 3-position 2O EB3P-SAW320-* W: White 5 Y: Yellow Maintained 3-position, return from right 2O EB3P-SAW3120-* Spring return from right 3-position,return from left 2O EB3P-SAW3220-* Spring return from left 3-position,2-way return 2O EB3P-SAW3320-* 2-way spring return 2-position 1O-1C EB3P-SHW211-* Maintained 3-position 2O EB3P-SHW320-* Maintained Round 2-position DPDT EB3P-S1W2C2-* Maintained Round w/square Bezel 3-position DPDT EB3P-S3W3C2-* Maintained 1. Codes, TW, HW, W, and UP are the series names of IDEC s control units. 2. Specify a color code in place of *. 3. Above parts are recommended for EB3 barriers. However, none of these parts are U recognized. 4. Buzzers are not rated for Zone 0, but only Zones 1 and Use PW (pure white) ED for yellow lenses Accessory Continuous sound EB3P-ZU12C Intermittent sound EB3P-ZU12F ame Ordering umber Package Quantity Remarks ED amp EB9Z-DS1-* 1 Static Electricity EB9Z Polyester 20(W) x 6(H) mm Caution Plate Above part is recommended for EB3 barriers. However, this part is not U recognized. Approx. 3 Hz Specify a color code in place of * in the ordering number. A: amber, G: green, R: red, S: blue, W: white, PW: pure white (for yellow use PW with yellow lens) Use PW (pure white) ED for yellow lenses 268

29 Switches and Pilot Devices Pilot ights ø30 EB3P-A1 Terminal Cover: AP-PV (sold separately) M3 Terminal Screw 21.5 Panel Thickness 0.8 to ø22 EB3P-AW1 ø35 Terminal Cover (supplied) APS-PV Panel Thickness 1 to 6 M3.5 Terminal Screw ø24 ø ø22 EB3P-HW1/EB3P-HW2/EB3P-HW4 Terminal cover attached. Panel Thickness 0.8 to 6 M3.5 Terminal Screw Gasket ocking Ring X2 X Flush Dome ø30 EB3P-U4 Terminal Cover: AP-PV (sold separately) M3 Terminal Screw ø22 EB3P-AW1B Round/Dome Miniature Pilot ights (Terminal cover not available) ø10 I-18 + Terminal 7 ø8 I-89 + Terminal M10.0 Panel Thickness 0.6 to ø M8 P0.75 Panel Thickness 0.6 to ø8.1 ø ø29 ø10 I-19 + Terminal 7 ø6 I-67 Panel Thickness 0.8 to 4.5 Square M10.0 Panel Thickness 0.6 to 4 M6 P Terminal ø9.9 ø Panel Thickness 0.6 to 4 ø ø30 EB3P-AD Terminal Cover: APD-PV (sold separately) M3.5 Terminal Screw 29.8 Panel Thickness 0.8 to ø22 EB3P-AW2 M3.5 Terminal Screw ø24.8 ø35 Terminal Cover (supplied) APS-PV Panel Thickness 1 to 6 ø23.6 ø ø40 ø22 EB3P-W1/EB3P-W2/EB3P-W3 Terminal cover attached. Gasket 7.2 ocking Ring ø8 I-87 + Terminal 6.1 ø6 I M3 Terminal Screw 7.7 M8 P0.75 Panel Thickness 0.6 to 4 M6 P Terminal ø Panel Thickness 0.6 to 4 ø ø30 EB3P-U3B Terminal Cover: AP-PV (sold separately) M3 Terminal Screw ø22 EB3P-UW1B M3.5 Terminal Screw Panel Thickness 0.8 to Terminal Cover (supplied) APS-PV Panel Thickness 1 to 6 9 ø Marking Plate: 22 Panel Thickness 0.8 to 6 Round ø8 I-88 + Terminal 6.1 ø6 I-69 Square 25.8 M8 P0.75 Panel Thickness 0.6 to 4 M6 P Terminal ø Panel Thickness 0.6 to 4 ø6 ø OI Touchscreens PCs Automation Software Power Supplies Sensors Communication IDEC (4332) USA & Canada 269

30 Switches and Pilot Devices OI Touchscreens Illuminated Pushbuttons ø30 EB3P-BA211/BAO211 Terminal cover: -V4 (2 pcs.) (sold separately) M3 Terminal Screw M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 ø30 EB3P-BAV311-R Terminal cover: -V4 (2 pcs.) (sold separately) M3 Terminal Screw M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 ø24 ø35 ø40 ø PCs ø22 EB3P-BAW211/BAOW211 Terminal cover attached. M3.5 Terminal Screw Adjustment Ring Panel Thickness 1 to 6 30 ø24 ø22 EB3P-BAVW411-R Terminal cover attached. M3.5 Terminal Screw Adjustment Ring Panel Thickness 1 to 6 30 Reset 75 ø22 EB3P-BH1W110/BHA1W110 Terminal cover attached. M3.5 Terminal Screw ocking Ring ever Stop Panel Thickness 0.8 to 6 OCK ø24 ø29 37 ø ø Automation Software ø22 EB3P-B1W1C2/BA1W1C2 Terminal cover: W-V2M (sold separately) M3 Terminal Screw 23.2 R18 OCK Panel Thickness 0.8 to 6 ø22 EB3P-B2W1C2/BA2W1C2 Terminal cover: W-V2M (sold separately) M3 Terminal Screw 23.2 R18 OCK Panel Thickness 0.8 to 6 Power Supplies 25.4 Illuminated Selector Switches ø30 EB3P-SA211/EB3P-SA320 Terminal cover: -V4 (2 pcs.) (sold separately) M3 Terminal Screw M3.5 Terminal Screw Panel Thickness 0.8 to ø ø22 EB3P-SAW*** Terminal cover attached M3.5 Terminal w Panel Thickness 1 to 6 All dimensions in mm. ø25 ø35 ø40 ø24 ø Sensors ø22 EB3P-SHW211/EB3P-SHW320 Terminal cover attached M3.5 Terminal Screw Panel Thickness 0.8 to 6 OCK ø29 ø22 EB3P-S1W2C2/EB3P-S3W3C2 Terminal cover: W-V2M (sold separately) M3 Terminal Screw R18 OCK Panel Thickness 0.8 to 6 ø Communication 25 Buzzer ø30 EB3P-ZU12C/ZU12F Terminal cover: AZ-V5 (sold separately) 29.4 EB9Z-DS Panel Thickness 0.8 to M3.5 Terminal Screw ø50 Illumination Color IDEC Exi 10.6 Intrinsic Safety Identification: ight Blue Illumination color is marked on the terminal