Set Up Guide. 521 East 3rd Street, Mount Vernon, NY Phone :: Fax :: Web ::

Transcription

1 KD-HDMS8X8 /DVI Matrix Switcher capable of switching up to 8 /DVI Video Sources/Inputs to 8 independent Zones/Outputs via /DVI and Also Available in Configurable Models Below: KD-HDMS1X15, 2X14, 3X13, 4X12, 5X11, 6X10, 7X9 KD-HDMS15X1, 14X2, 13X3, 12X4, 11X5, 10X6, 9X7 Set Up Guide Key Digital, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge technology solutions for virtually all applications where high quality video imaging is important. Key Digital is at the forefront of the video industry for Home Theater Retailers, Custom Installers, System Integrators, Broadcasters, Manufacturers, and Consumers. Key Digital Hercules Series KD-HDMS8x8 is a /DVI Matrix Switcher capable of switching up to 8 /DVI Video Sources/Inputs to 8 independent Zones/Outputs via /DVI and. Features card slot architecture providing flexible Input/Output configurations. 521 East 3rd Street, Mount Vernon, NY Phone :: Fax :: Web :: Rev 1 Oct 2011

2 Page 2 Page 3 Table of Contents About KD-HDMS8X Connections, LCD and Button Map Application Example Quick Setup Guide Remote Command List RS-232 Control Codes Specifications Important Product Warnings & Safety Instructions How to Contact Key Digital Warranty Information About KD-HDMS8X8 1.4 Features 3D Capability to pass 3D stereoscopic signal formats 4K 4096x2160/24 video resolution support for commercial applications such as Digital Movie Theaters, CAD, Post Production, Graphics and etc. Key Features Full switching of 4 independent matrixes: Video, Analog Audio, Digital Coaxial Audio, Audio Master Control function of Control system to Input Output connection for Bi-Direction, and Bi-Directional RS-232 Control Supports all SD, HD, and VESA (VGA, SVGA, XGA, WXGA, SXGA, UXGA) resolutions up to 1080p (60Hz & 50Hz) SD & HD: 480i, 575i, 480p, 576p, 720p, 1080i, 1080p VESA / VGA (RGBHV): From 640x480p up to 1920x1200p Supports switching of lossless compressed digital audio: Dolby TrueHD, Dolby Digital Plus and DTS -HD Master Audio Internal EDID Library features 8 default EDID configurations, in addition to Native EDID data for any Output/Display Full Buffering of HDCP and EDID for seamless and fast switching TMDS re-clock for support of long /DVI or connections and daisy chain configurations. Key Benefits Transmits 1080p/60Hz resolution up to 140 ft. and 1080p/24, 1080i, 720p and 480i/p resolutions up to 270 ft. when used with KD-BBRX receiver Baluns Video, Audio, and RS-232 distribution via a single cable Fully automatic cable equalization 16 active outputs (8 /DVI and 8 ) enables flexible integration Full Audio control per output for volume, treble, bass, balance, and lip-sync die 2-ch stereo formats from analog or digital sources Serial, Optical, Front Panel & RS-232 control. Supports major control systems such as AMX, Control4, Crestron, RTI, Universal. Accessories External +12V/8.33A (100W) Power Supply KD-PS12V8A Remote control with two batteries Cable Clips (16) 6 ft. USB Data Cable Connections, LEDs and Button Map Front Panel Left Selector Use to access Main Menu and select sub-menu choices. (see pg.7 for complete operating instructions) Rear Panel Looking at the rear panel, card slots are numbered from left to right Input Cards 1-8 (KD-HDUIC) Please see p. 4 for detailed description LCD Screen Displays Menu selections, Input and Output information, system settings and status information Right Selector Use to access sub-menus within the Main Menu. (see pg.8 for complete operating instructions) Output Cards 1-8 (KD-HDUOC) Please see p. 4 for detailed description Eye Main Control Panel Please see p. 4 for detailed description 2011 Key Digital, Inc. All rights reserved.

3 Page 4 Page 5 Main Control Panel For manufacturers use only Operation Mode Switch Switch to Program mode when updating firmware Rear Eye (Receiver) Rear receiver for remote control Power 12V/8.33A (100W) Power Supply Application Example Desktop PC Desktop PC Satellite 1 Satellite 2 Cable 1 Cable 2 Blu-Ray Blu-Ray DVI Video* L/R/PCM DVI Video* L/R/PCM KD-BBTX KD-BBTX KD-BBTX KD-BBTX TCP/IP This is the main TCP/IP port for interfacing with control systems. It supports the same control commands as the RS-232 port and it can support TCP/IP to RS-232 conversion & routing and TCP/IP to serial conversion & routing. USB The USB port is for software upgrades only. It is not used for control interface. RS-232 The main RS-232/DB9 port for interfacing with a control system. Serial To Input from Control interface for controlling unit via Serial and routing Input and Output Numbering The KD-HDMS8x8 in its default configuration contains 8 Input cards and 8 Output cards. The Input cards are addressed from 01-08, and the Output cards from Transmits:»1080p/60Hz resolution up to 140 ft»1080p/24, 1080i, 720p and 480i/p resolutions up to 270 ft» When used with KD-BBRX Receiver Baluns KD-HDMS8X8 Serial Optical RS232 Control Control System /RS-232 & TCP/IP Rx Input Card (KD-HDUIC) Left Analog Audio / PCM Audio Input Supports Left channel Analog Audio Input or use for Coaxial Digital Audio Input Input Integrate a remote source by using the KD-BBTX Transmit Balun to feed the inputs Input To Input source components /DVI Audio /RS-232 DVI /RS-232 /RS-232 /RS-232 /RS-232 /RS-232 /RS-232 L/R/PCM /RS-232 L/R/PCM USB TCP/IP Surround Rcvr. Right Analog Audio Input Supports Right channel Analog Audio Input Serial / RS-232 Use the KD-HDMS as a Control Router for devices integrated into your system Link LED Indicates that input connection is stable KD-BBRX 180 KD-BBRX KD-BBRX KD-BBRX Tx Output Card (KD-HDUOC) Left Analog Audio / PCM Audio Output Send Left channel Analog Audio or Coaxial Digital Audio to your Display or other devices Output Use the KD-BBRX Receive Balun to carry Video, Audio, and Control to your Display (or other) devices Output To Output to Display (mirrored) Display 1a (mirrored) Display 2a Display 3 Display 5 Speakers Display 1 Display 2 Display 4 Display 6 *To connect DVI use to DVI adapters Display 7 Display 8 Right Analog Audio Output Send Right channel Analog Audio to your Receiver or other devices Serial / RS-232 Use the KD-HDMS as a Control Router for devices integrated into your system Link LED Indicates that output connection is stable

4 Page 6 Page 7 Quick Setup Guide Initial Setup & Operation for via Front Panel The KD-HDMS8x8 is set by default to Input. To change these default settings please see Initial Setup & Operation via Baluns section below. 1. Insert cables into card slots 1 through 16 Slots 1-8 are labeled Rx, and are Input Card Slots 1-8. Slots 9-16 are labeled Tx, and are Output Card Slots 1-8. Connect your source components to the Input cards Connect your displays to the Output cards Power up all sources and displays 2. Establish an Handshake for Each Source Push the left selector to access the Main Menu choices Using the left selector, scroll to the 7-EDID Setup Menu Press the right selector to navigate to the EDID sub-menus With the left selector, scroll to the Input source you wish to copy the EDID to Using the right selector, scroll to the or Output you wish to establish an handshake for, or select a Default EDID from the EDID library (see pg.10) Press the right selector to set the Handshake for that combination Continue this procedure for all Inputs The EDID control and input set up is stored in a non-volatile memory back up and is only required during initial set up or when a new display or source is added to the system. Establish a default handshake for ALL Inputs: Using the 7-EDID Setup Menu, select ALL Inputs and scroll to the Output number you wish to copy the EDID from (, or a Default EDID setting) and press the right selector 3. Switching via Front Panel Push the left selector to access the Main Menu choices Using the left selector, scroll to the 1-Video Switch Menu Press the right selector to navigate to the Video Switch sub-menus Using the left selector, scroll to the Output you wish to select Using the right selector, scroll to the Input you wish to select Finally, press the right selector to make the switch 4. Sending your output via KD-BBRX Receive Balun(s) Both and Outputs are active on all Output Card Slots, therefore no configuration is necessary to activate the Output for each Tx Card Slot. 5. Sending your source via KD-BBTX Transmit Balun(s) Set dipswitch #2 of the KD-BBTX Balun to DDC in order to establish a proper handshake Configure the appropriate Input Card Slot to activate its input using the 6-Video Input Setup Initial Setup & Operation via Baluns When using Key Digital Baluns (RX/TX) you must use the following procedure to correctly format both the baluns and HDMS8x8 matrix switcher for correct operation. NOTE: Slots 1-8 are inputs, slots 9-16 are outputs. The KD-BBTX Dipswitch #2 MUST be set to the DDC position. IMPORTANT: Make sure that you power up all baluns, sources and displays. Confirm that you have an active connection on the Balun indicated by the solid red LINK LED. 1. By default, the KD-HDMS8x8 is configured to accept a direct connection. When using a KD-BBTX, you MUST change the input mode from to to enable the switcher to see the /Balun input. Select 6-Video Input Setup from the main menu. Press the right selector to navigate to the sub-menus. Using the left selector, scroll to the Input number you wish to change. Using the right selector, scroll to select and press the right selector to enter your choice. 2. Repeat procedure for any other input where a KD-BBTX is being used. 3. Once you have correctly configured the inputs to accept either and/or /Balun, you need to establish the correct handshake. 4. See previous section on establishing an handshake. Front Panel Menu Selection Controls: Power On The unit will power up with a push on either the left or right Selector. Power Off Dispwitch # - Select DDC The unit will power off through, Remote, RS-232 or TCP/IP commands only. Left Selector Main Menu: To access the Main Menu push this selector once. To Select Main Menu Options: Turn selector left or right to select Menu Options 1-9 Sub-Menu values: Turn this selector to scroll through the sub-menu selections. There will be left and right sub-menu choices. Use the left selector to change left side options To Go-Back to a previous menu: from whatever menu you are presently in you may return to the previous menu by pressing this selector once. You will return to the menu you were previously in.

5 Page 8 Page 9 Right Selector Sub-Menu: After selecting a specific Main Menu (1-9) option with the left selector, press the right selector to select its Sub-Menu. You will be taken to the sub-menu for the main menu option you had previously selected. Sub-Menu values: Turn this selector to scroll through the sub-menu selections. Use the right selector to change right side options. After a sub-menu choice has been made, push this selector once to enter it. The display will blink to acknowledge your choice. Menu Tree on LCD Display Main Menu Selections: Using the left selector, choose from the following Main Menu options; 1. Video Switch 2. Audio Switch 3. Volume Control 4. Audio Output Set Up 5. Audio Input Set Up 6. Video Input Set Up 7. EDID Set Up 8. TCP/IP Set Up 9. Factory Default Using the right selector, push to enter the submenu for any of the selected main menu options above; Sub-Menu Selections: 1. Video Switch options: Output All Outputs For each Output number selected, and All, there are Input sub-menu choices; Input Use the right selector to choose these and push to confirm your choice for both Select an Output number with the left selector and then select an Input number you wish to feed that output by turning the right selector. Push the right selector to select that combination. The display will blink to acknowledge your choice. This will immediately switch your Output to the Input selected. 2. Audio Switch options: Output plus All Outputs For each Output number selected, and All, there are Audio sub-menu choices: External Analog External Digital Use the right selector to choose these and push to confirm choice. These correspond to which Audio signal type will be passed to the selected Output number from your previously selected Input number. 3. Volume Control Set Up options: Output plus All Outputs Use the left selector to choose Output number desired. Use the right selector to choose Volume level desired (00-99) and push to confirm choice. Continue for all Outputs you wish to change 4. Audio Output Set Up options: Output plus All Outputs For each Output number selected, and All, there are Audio Output sub-menu choices: Digital Analog Use the right selector to choose these and push to confirm choice. These correspond to the RCA connectors only and choose which format will be passed to the Output selected. 5. Audio Input Set Up options: Input plus All Inputs For each Input selected, and All, there are Audio Input sub-menu choices; Digital Analog Use the right selector to choose these and push to confirm choice. These correspond to the RCA connectors only and choose which format will be accepted by the Input selected. 6. Video Input Set Up options: Input plus All Inputs For each Input selected, and All, there are Video Input type sub-menu choices: Use the right selector to choose these and push to confirm choice.

6 Page 10 Page EDID Set Up options: Input plus All Inputs For each Input selected, and All, there are EDID Set Up sub-menu choices: Output 01 through 08 Output 01 through 08 For each Input (source) selected with the left selector there is a choice to copy the EDID information from either the or connected Output (display) using the right selector depending on which is connected. Both and Inputs will receive the copied EDID information. The Default choices (listed below) copy the EDID from a stored library of EDID configurations to the selected Input card across both and Inputs. Default EDID 1 (1080i 2CH PCM) Default EDID 2 (1080p 2CH PCM) Default EDID 3 (1080i PCM, DTS/DOLBY. not including HD audio) Default EDID 4 (1080p PCM, DTS/DOLBY. not including HD audio) Default EDID 5 (1080i every audio including HD audio) Default EDID 6 (1080p every audio including HD audio) Default EDID 7 (3D 1080p 2CH PCM) Default EDID 8 (3D 1080p every audio including HD audio) Use the right selector to choose these and push to confirm choice. You will receive a Completed message when successful, or a Failed message if unsuccessful. 8. TCP / IP options: IP address Sub net Mask Port The default IP address is; This can be changed to accommodate your particular configuration or controller. The default Sub net mask is and may also be changed to accommodate your particular configuration. The default Port number is 23 Select the TCP/IP option by pressing the right selector. Highlight the group of numbers you wish to change by turning the left selector. Change the group of numbers using the right selector. Continue this procedure until all numbers are chosen. Press the right selector to enter the changes. You may then press the left selector to return to the previous menu if desired. 9. Factory Default options: This option will return the unit to its Factory Default settings. Please see the list of default settings below. When this menu option is chosen, you will be presented with a choice of EDID s from the default EDID library. Choose one of these default EDID s (typically default i 2Ch PCM) using the left selector, then press the right selector to confirm. The unit will then reset to the default configuration including the EDID you have chosen. Factory Default Settings: Video = Input = 1 Input Audio = Analog Output Audio = Analog Audio = Port = Output Volume = 50 Output Bass = 12 Output Middle = 12 Output Treble = 12 Output Balance = 20 Output Delay = 00 EDID = Choice of default EDID library (see menu 7-EDID Set Up for a list of default EDID choices pg.10) TCP / IP = Power On Power OFF Video Mode R1 Button R3 Button Tone Controls: Bass, Middle, Treble Balance All Mute / Mute Numeric Keypad Audio Mode R2 Button Arrow Up, Down, Left, Right R4 Button Volume LipSync (Delay) All Restore / Restore

7 Page 12 Page 13 KD-HDMS8x8 Remote Command List Below are listed some of the most common remote commands. A complete list of all Remote commands can be found at the Key Digital website The following commands assume an 8x8 configuration. XX = Output Card Number (Range 01~08) [Outputs 1-8] YY = Input Card Number (Range 01~08) [Inputs 1-8] ZZ = Numeric Keypad Number (Range 00~99) Arrows = Up Down Left - Right Power On = Power On Power Off = Power Off Switching Commands Switch Input to Output: To Switch Output and Input cards by numeric keypad: R1 XX Video Mode YY Example: To switch Input 3 to Output 2 press; R1 02 VideoMode 03 Switch Audio Output Source Type: To Switch Audio source of Output Card by numeric keypad: R1 XX Audio Mode ZZ Where ZZ is: 01 = 02 = RCA COAX SPDIF 03 = RCA ANALOG 04 = AUDIO Example: To switch the audio source for output 2 to press; R1 02 AudioMode 04 Front Panel Commands Using Remote The Remote can be used to navigate through the front LCD display options. Use the Left and Right Arrow keys to choose options normally made by rotating the Left Selector. Use the Up and Down Arrow keys to choose options normally made by rotating the Right Selector. Use the R2 button to enter choices normally made by pushing the Right Selector. Use the R4 button to enter choices normally made by pushing the Left Selector. RS-232 Control Codes Baud Rate: Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None Carriage Return: Required RS-232 cable pin out Pin 5 Ground Pin 3 Receive Pin 2 Transmit Initial Setup & Operation via RS-232 A complete list of RS-232 Commands can be found at Key Digitals website: 1. Insert cables into card slots 1 through 8 Slots 1-8 are labeled Rx, and are Input Card Slots. Slots 9-16 are labeled Tx, and are Output Card Slots. 2. If integrating your source via KD-BBTX Transmit Balun(s) Set dipswitch # 2 of the KD-BBTX balun to DDC in order to establish a proper handshake Configure the appropriate Input Card Slot to activate its input using SP I xx V y RS-232 command. Where xx = Card Slot # of desired Input Where y = 1 or 2 (1 =, 2 = ). Note: The default input configuration is 1 for. 3. If integrating your output via KD-BBRX Receiver Balun(s) Both and Outputs are active on Output Card Slots, therefore no configuration is necessary to active the Output for each Tx Card Slot. 4. Establish an Handshake for Each Source Copy EDID to Rx Card (xx) from Tx Card (yy) using SP C EDID xx H/C/D yy Where xx = Card Slot # of desired Input (01-08) Where H =, C = or D = Default EDID Library (01-08) Where yy = Card Slot of # of desired Output (if H or C) (01-08) OR Where yy = Default EDID library # (01-08 ) (if D) *see Default EDID list pg Matrix Switching via RS-232 Use RS-232 command SP Oxx SI yy xx = Card Slot # of desired Output yy = Card Slot # of desired Input NOTE: Spaces between RS-232 commands are shown for clarity only. Actual RS-232 commands do not need any spaces between characters. RS-232 Commands Command Name Command Value Description Status STA Gives full listing of Unit s Status Help H Gives full listing of RS-232 Commands Power Off Power On PF PN

8 Page 14 Page 15 Set Video Input port Set RCA Audio Input type Set Output to Video Input Set Output to Audio Input Set Output Volume SPIxxVy Input and Output numbers assume an 8x8 configuration. SPIxxRCAy Values for Commands: Inputs: yy = or A = All, U = Up, D = Down Outputs: xx = or A = All, U = Up. D = Down System Input Setup Commands, xx = [01-08, A], (A=All): xx = Input number y = Input type (1-, 2-CAT6/ STP) xx = Input number y = RCA Audio type (1-Analog, 2-Digital) To set which Video input type will be active by specific input number. Example: To set input 2 to, issue the command; SPI02V1 Example: To set input 2 to issue the command: SPI02V2 Example: To set ALL inputs to issue the command: SPIAV1 To set which Audio input type will be active. Example: To set RCA input number 2 to Analog, issue the command: SPI02RCA1 Example: To set ALL RCA inputs to Analog, issue the command; SPIARCA1 Example: To set RCA input number 2 to Digital, issue the command; SPI02RCA2 System Output Setup Commands, xx = [01-08, A], (A=All): SPOxxSIyy SPOxxSAyy SPOxxAVyy xx = Output number (01-08) yy = Input number (01-08) or [U, D] (U=Up, D=Down) xx = Output number yy = choice of Audio Input type desired, routed to that Output. (01-, 02-EXT PCM, 03- EXT ANALOG, 04-) xx = Output number or A (for All) yy = Volume value To switch Video Inputs to an Output. Example: To switch Video at input 2, to output 6, issue the command; SPO06SI02 Example: To step through each input going up through the inputs, issue the command; SPO01SI(U), each time this command is issued, the selected output (1 in this case) will step through the inputs in ascending order starting with the presently selected input.to step through the inputs in descending order from the presently selected input, use SPO01SI(D). (Do not add parentheses). *NOTE: the above parameters are for an 8x8 configuration. To set which Audio format is routed to which Output. Example: To set output 6 to route External Analog Audio, issue the command; SPO06SA03 NOTE: This command must be issued in concert with the above switching command for Video only. To set the Output Volume per Output number or ALL outputs. Example: To set Output 6 to 60, issue the command; SPO06AV60 Copy EDID information to Rx card slot, from Tx card slot yy via /CAT6 ult EDID library Front Panel Buttons Adjust EQ for length per Input Configure CAT6/ STP Output to either DDC or PCM Audio Reset to Factory Defaults SP C EDID xx H/C/D yy System Control Setup Commands: xx = Input card number (01-08), H =, C =, D = Default EDID library yy = (01-08), Output card number when H / C is selected OR- (01-08) Default EDID library when D is selected. SPCFBE/D E = Enabled / D = Disabled SPCCAT6/ STPIC xxyy SPCCAT6/ STPOC hhhh SPCDFxx xx = Input number yy = EQ Value 0-40 (default is 20) hhhh = hex value for Input or Output numbers selected. xx = and represents the default EDID choice desired after reset. (See menu 7-EDID Set Up options for default EDID choices) To copy the EDID information from an Output card (display), to an Input card (source). Example: To copy the EDID information from Output 2, to Input 4, issue the command; SPCEDID04H02 Example: To copy the EDID information from CAT6/ STP Output 2, to Input 4, issue the command; SPCEDID04C02 Example: To load DEFAULT2 EDID library for Input card 3, issue the command; SPCEDID03D02 Below are the Default EDID library choices when selecting D as a variable: 01 = DEFAULT1 (1080i 2CH PCM) 02 = DEFAULT2 (1080p 2CH PCM) 03 = DEFAULT3 (1080i PCM, DTS/DOLBY. not including HD audio) 04 = DEFAULT4 (1080p PCM, DTS/DOLBY. not including HD audio) 05 = DEFAULT5 (1080i every audio including HD audio) 06 = DEFAULT6 (1080p every audio including HD audio) 07 = DEFAULT7 (3D 1080p 2CH PCM) 08 = DEFAULT8 (3D 1080p every audio including HD audio) To Enable or Disable the front panel buttons. Example: To Disable the front panel buttons, issue the command; SPCFBD To adjust Input EQ for fine tuning Video signal if necessary Example: To adjust Input 6 EQ to value 30, issue the command: SPCIC0630 To set Output to either DDC (Data Display Channel) or PCM Audio. Default or unselected will be DDC, selected Inputs/ Outputs will be PCM Audio. Binary value 0 = DDC, 1 = PCM Audio Example: To set the output of outputs 1 and 6 to PCM, issue the command; SPCCAT6/ STPOC2100, all other outputs will remain DDC To reset factory default settings by type. Example: To reset to 1080p HD Audio EDID, issue the command; SPCDF06 Please see our website product page for a complete list of all RS-232 commands:

9 Page 16 Page 17 Specifications Video Input Interface ( Input Card): Has both and (RJ45) Inputs, only 1 of these Inputs can be selected per Input card Supports 1.3a and 3D Feature of 1.4 (RJ45) works only with KD-BBTX Balun and with KD-CATHD(TX) Baluns. Video Output Interface ( Output Card): Features both and (RJ45) outputs, and provides both simultaneously. Supports 1.3a and 3D Ready, 4K Resolution Support features of 1.4 (RJ45) works only with KD-BBRX Balun and with KD-CATHD(RX) Baluns.. Audio Input Interface ( Input Card): Supports both PCM and Analog Stereo Audio inputs. The PCM Input shares the same RCA connector as Left Analog stereo and only one of these audio inputs / formats can be selected at a time. The Analog Stereo Audio input is processed at 48kHz sampling rate. Audio Output Interface ( Output Card): Supports both PCM and Analog Stereo Audio Outputs. The PCM Output shares the same RCA connector as Left Analog stereo and only one of these audio outputs / format types can be selected at a time. 1. When the PCM Output is selected and its source is from the external PCM Input, PCM (at 48 khz) will be in bypass mode to pass Dolby Digital, DTS, or 2Ch PCM and will be without audio control. 2. The Analog Stereo Audio Input is processed (at 48 khz) and will be converted to digital audio at the PCM Output if desired. Full audio control will be available in this case. 3. When HD Audio (HD-Dolby Digital, HD-DTS etc.) or multi-channel PCM is carried by, it will be muted at the PCM Output if is selected as the audio input source. Control Interface ( Input/Output Card): Supports both RS-232(up to bps) and Serial and shares the same stereo minijack. Only one control protocol can be selected through control port settings. RS-232 and Serial support bi-directional paths. Output signal level is +5V TTL and has +/-12V tolerance. Control Interface (Power Board): Supports one RS-232(DB9), one TCP/IP(RJ45), one USB(B Type) for service only (software upgrade), one Serial and one Eye. RS-232 baud rate for control of unit is fixed at 57,600bps. RS-232 and TCP/IP share same control commands. Serial supports bi-directional path. Output signal level is +5V TTL with +/-12V tolerance. Eye is only for Remote receiving sensor. Front Panel Interface: 2 row LCD Display, two rotary knobs(left and right) with push-to-select action to control menu choices for front panel control, and Eye Eye is only for Remote receiving sensor. Technical: Regulation: RoHS, WEEE Input (Each): 1 ; 1 on RJ-45 connector; Left and Right Stereo on two RCA, or one SPDIF digital audio on Left RCA connector; 1 wired or RS-232 on 3.5 mm stereo jack connector per input Output (Each): 1 ; 1 on RJ-45 connector; Left and Right Stereo on two RCA, or one SPDIF digital audio on Left RCA connector; 1 wired or RS-232 on 3.5 mm stereo jack connector per output Configuration: 8 input sections and 8 output sections in standard configuration Bandwidth: TMDS bandwidth 10.2 Gb/s Control: Front panel push buttons and LCD display; Infrared front; RS-232 Tx and Rx lines; Full bi-directional operation Video/Audio Matrix Switching: Full Matrix switching of 2 independent matrixes: Video & Audio RS-232 Control Matrix: RS-232 input/output can independently control the system or input/output through attached KD-BBTX or KD-BBRX Balun. Full bi-directional RS-232. Wired Control Matrix: Each input/output section wired and unit wired can be switched into matrix in bi-directional operation to any of the inputs/outputs EQ adjustment: On Rx Balun or Input. Precise auto-adjustment, distance measurement Compliance with Standards: Supports 1.4 features (3D Ready, 4K Resolution Support), 1.3a/b, 1.2, 1.1, DVI 1.1, and HDCP Link and Range: Single Link Range: 1080p/60, 1920x1200 max. UTP 140 feet. STP 160 feet. For 1080i/60; 720p; 1080p/24 UTP 270 feet, STP 280 feet Lossless Compressed Digital Audio: Support lossless compressed digital audio (Dolby TrueHD, Dolby Digital Plus and DTS -HD Master Audio) DDC Signal (Data): Input DDC Signal: 5 Volts p-p (TTL) Video/Audio Signal: Input Video Signal: 1.2 Volts p-p Connector: Type A, 19 Pin Female RJ45 Connector: Link Connector: RJ-45 Shielded I2C Communication: EDID and HDCP Bi-Directional Transparency from Display to Source EDID Control: Each input EDID is either a choice of any of the active zone displays connected via or to the outputs or from internal library of 8 Default EDIDs RS-232: RS-232 Tx and Rx line active and bi-directional up to 115,200 baud rate Wired : line modulated or not modulated, active and bi-directional 0-5V TTL or -10to +10V. Power: External Power Supply. 12V/8.33A

10 Page 18 Page 19 General: Regulation: CE, FCC, RoHS, WEEE Rack Mount: 3RU, Full Rack Width (rack ears included) Enclosure: Black Metal Product Dimensions: L = 17.5 W = 9.25 H = 5.25 Shipping Carton Dimensions: L = 20 W = 12.4 H = 8 Product Weight: 14 lb. Shipping Weight: 24 lb. Accessories: Remote Control, UL Certified Power Supply - 12V / 8.33A, 16 Cable Clips, 6ft USB Data Cable How to Contact Key Digital System Design Group (SDG) For system design questions please contact us at: Phone: sdg@keydigital.com Technical Support For technical questions about using Key Digital products, please contact us at: Phone: tech@keydigital.com Repairs and Warranty Service Important Product Warnings: 1. Connect all cables before providing power to the unit. 2. Test for proper operation before securing unit behind walls or in hard to access spaces. 3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper screw support with bolts or sheet-rock anchors. Safety Instructions. Please be sure to follow these instructions for safe operation of your unit. 1. Read and follow all instructions. 2. Heed all warnings. 3. Do not use this device near water. 4. Clean only with dry cloth. 5. Install in accordance with the manufacturer s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way including: Damage to the power supply or power plug Exposure to rain or moisture Should your product require warranty service or repair, please obtain a Key Digital Return Material Authorization (RMA) number by contacting us at: Phone: rma@keydigital.com Feedback Please any comments/questions about the manual to: customersupport@keydigital.com Warranty Information All Key Digital products are built to high manufacturing standards and should provide years of trouble-free operation. They are backed by a limited two-year parts and labor warranty. You MUST use the Power Supply provided with your unit or you VOID the Key Digital Warranty and risk damage to your unit and associated equipment.