Phantom Series. HDMI Switchers with Audio De-Embedder, Coaxial Audio, Optical Digital Audio & Analog L/R, support Ultra HD/4K

Transcription

1 Rev 0 June 2014 Key Digital, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge technology solutions for virtually all applications where high quality video imaging is important. Key Digital is at the forefront of the video industry for Home Theater Phantom Series Switchers with De-Embedder, Coaxial, Optical Digital & Analog L/R, support Ultra HD/4K Retailers, Custom Installers, System Integrators, Broadcasters, Manufacturers, and Consumers. Operating Instructions KD-HD2x1ProK The Experts in Digital Video Technology and Solutions Key Digital Systems :: 521 East 3rd Street :: Mount Vernon, NY Phone : Fax : Phantoms_HDProK_Switchers_Manual.indd 2-3 Web : 6/5/14 10:48 AM

2 4 1 Table of Contents Introduction... 1 Quick Setup Guide... 2 Installation and Operation... 3 DVI Applications... 3 IR Remote Control & IR Emitter Control... 4 Settings... 5 External Outputs... 6 Commands and Protocol... 6 Using ias Intelligent Auto Sense... 7 Specifications... 7 Important Product Warnings & Safety Instructions:... 8 How to Contact Key Digital... 9 Warranty Information... 9 Always follow the instructions provided in this Operating Manual Key Digital, Inc. All rights reserved. Introduction Key Digital Phantom Series switchers are designed and engineered to offer the best quality, performance, and reliability while providing a cost-effective /DVI switching solution. Phantom Series switchers are a transparent solution for all digital video/ audio switching applications and support all HD and SD video standards, including Ultra HD/4K, 3D and 1080p/60. KD-HD2x1ProK / switchers feature ias (Intelligent Auto Sense) signal detection and automatic switching, pushbutton control, IR,, status-monitoring LEDs, and support for CEC. The Phantom Series switchers support multiple unit expandability, and are individually addressable. Key Features Digital Switching: 2/4 Sources to 1 Display Resolution Support: Supports all SD, HD, and VESA (VGA, SVGA, XGA, WXGA, SXGA, UXGA) resolutions up to Ultra HD/4K, 3D and 1080p/60 (60Hz & 50Hz)» SD & HD: 480i, 480p, 720p, 1080i, 1080p and Ultra HD/4K» VESA: From 640x480p up to 1920x1200p 3D Ready: Capability to pass 3D stereoscopic signal formats Ultra HD/4K: 4K/2K video resolution support for 4K-capable televisions and commercial applications such as Digital Movie Theaters, CAD, Post Production De-Embedder: Can de-embed audio from the input and send it to external digital or analog audio outputs Lossless Compressed Digital : Dolby TrueHD, Dolby Digital Plus and DTS-HD Master : 16 internal library settings or auto EDID detection from display Licensing: Fully licensed and compatible with all and HDCP technologies I2C Communication: EDID and HDCP transparency from Display to Source Control: Front panel push buttons and LEDs, Deep Color Support: Up to 12 bits/color Signal rates: up to 3.4 Gb per second CEC: Fully Supported Firmware upgradable Rack mountable Accessories External power supply: 5V 2A Lacing Clips Rack Ears Operating Instructions Warranty Card

3 DVD Subwoofer 2 3 Blu-Ray Rcvr. Plasma Quick Setup Guide TV Installation and Operation Step 1: Find a safe and convenient locationoptical toir mount or place your KD-HD ProK unit Step 2: Begin with the KD-HD ProK unit and all input/output devices turned off with power Step 3: Step 4: Step 5: Step 6: Step 7: Step 8: DVD cables removed Rcvr. Connect your or DVI-D source devices to the input ports of your KD-HD ProK unit Connect your or DVI-D display to the output port of your KD-HD ProK unit Connect the desired IR or control inputs to your KD-HD ProK unit Be sure the Operation Mode Switch is set to the Normal position Connect power to the KD-HD ProK unit Power on input/output devices Subwoofer Before permanently securing the unit for final installation, test for proper operation of the unit and cables in your system. It is recommended that you leave enough Blu-Ray ventilation space to provide sufficient airflow and cooling. An optional cable clip (included) allows for a secure cable connection to be made to the rear of DVD and helps defeat intermittent or complete signal the unit loss due to poor connection. Optional clip (included) Active Input / Output LED Indicators Your KD-HD ProK unit may be controlled via the pushbutton on the front of the unit. Select your desired input by depressing the Input Select button. The front LED indicators (1, 2, 3, 4) correspond to the selected input. Blu-Ray DVD Rcvr. /DVI DVI Applications KD-HD can also be used with DVI-D sources and displays. For these *To connectprok DVI, use to DVISwitchers adapters applications, use DVI to adapters. Note that while supports both video and audio over an cable, DVI-D supports only video. Sub-Woofer Rcvr. Laptop /DVI *To connect DVI, use to DVI adapters DVI Sub-Woofer Laptop *To connect DVI, use to DVI adapters Note: N o signal conversion is done on the KD-HD2x1ProK;. If input signal is output signal will be. If input signal is DVI output signal will be DVI. Laptop Phantoms_HDProK_Switchers_Manual.indd 2-3 6/5/14 10:48 AM

4 4 5 IR Remote Control The KD-HD ProK switcher features IR sensors on the front and rear of the unit for reception of the IR signals, and can be operated using the IR remote control provided with your unit. Power Auto Input Select Input Select Scroll Down Numeric Keypad & IR Emitter Control Input Select Input Select Scroll Up R1, R2, R3 Reserved for future use The port requires the use of a Male 3.5mm Mono cable (not included) with the IR command signal being carried on the Tip of the input inserted into the KD-HD ProK unit. The location of the IR signal may vary by control system used. Please verify the location of the IR signal with your control system. Ground Signal When using the IR Emitter / IR Extender (sold separately), the IR Emitter must be mounted over the IR Sensor on the KD-HD ProK unit. It is recommended that the rear IR sensor of the KD-HD ProK unit be utilized for these applications. One end of the cable is connected to the IR Receiver / Master Controller / IR Extender / IR Connecting Block, while the other end is mounted over the IR Sensor of the KD-HD ProK unit. Settings At times, your sources and display may not synchronize properly. This is when EDID* control should be utilized. KD-HD ProK Switchers feature an internal library of EDID settings to ensure your source s output is compatible with the display devices. Please reset the unit by either unplugging and plugging the connections, or via a power cycle for the new settings to take effect. EDID Settings The default EDID is 00 --Copy EDID from output. The 16 possible EDID settings range from 00 to F. ( 00 is the default). 00 Copy EDID from Output A 4Kx2K, 2CH AUDIO i, 2Ch B 4Kx2K, DOLBY/DTS i, Dolby/DTS 5.1 C 4Kx2K, HD AUDIO i, HD D 1280x1024 DVI p, 2Ch E 1920x1080 DVI p, Dolby/DTS 5.1 F 1920x1200 DVI p, HD 07 3D, 2Ch 08 3D, Dolby/DTS D, HD Addressing Mode Units may be addressed when used in a cascaded configuration. To address your Champion Series switch, press the following buttons on the Key Digital IR remote control: R3» R1» R2» XX The XX characters will be replaced with the two digit address you wish to assign to the unit. The default address is 00--Single unit mode. HPD Control Rotary Switch You may force Hot Plug Detection (HPD) to a source, or use Normal HPD mode (default). To set the Normal HPD mode (default) press the following buttons on the Key Digital IR remote control: R1» R2» R3» 0» 1 So set Forced HPD on, press the following: R1» R2» R3» 0» 0 Resetting to Factory Default To reset your unit to factory default, press and hold the Input Select button on the front panel for 10 seconds. * EDID (Extended display identification data) is a data structure provided by a display to describe its capabilities to a source device.

5 6 7 Example of EDID Auto Select: If one of your system s displays supports 1080p and the second display only supports up to 1080i (does not support 1080p), then the highest common EDID format supported is 1080i. By choosing the Auto Select EDID Setting, your KD-HD ProK unit will inform your source device to output 1080i in order to ensure all displays receive a supported signal. External Outputs Analog audio output via 3.5mm stereo phone jack 2 channel analog audio output from the selected input source Converts only 2 ch. PCM audio from the input to 2 channel analog audio output Only supports 2 ch. PCM audio, not multi-channel PCM, Dolby, DTS, HD audio Digital audio output via Coax/RCA Digital audio output from the selected input source Uses SPDIF format Supports 2 ch. PCM, Dolby, DTS; does not support multi-channel PCM or HD audio Digital audio output via Optical Digital optical audio output from the input Uses SPDIF format Supports 2 ch. PCM, Dolby, DTS; does not support multi-channel PCM or HD audio Commands and Protocol KD-HD ProK units are compatible with all Control Systems, such as Compass Control, AMX, Control4, Crestron, RTI, Universal Connect your Control System s Master Controller to the KD-HD ProK unit using the port. Follow all instructions provided with your control system. Protocol: Baud Rate = bits per second Data Bits = 8 / Stop Bits = 1 Parity = None Flow Control = None All commands must be in lower case letters Command must be terminated with a carriage return Command Azz H PF PN Description All Commands may have Prefix System Address zz=[01-99] Help Power Off Power ON STA Show Global System Status Video Output Setup Commands: yy = [01-04] (A=All) SPO SIyy Set Output to Video Input yy SPO ON/OFF Set Output ON/OFF Output Setup Commands: [E=Enable, D=Disable] SPO AA E/D Enable/Disable External Analog Output SPO DA E/D Enable/Disable External Digital Output System Address Setup Command: xx = [00-99], 00 = Single SPC Axx Set System Address to xx System Control Setup Commands: SPC AS x Set Auto Sense Mode x = [ 0:OFF, 1=AUTO, 2=FORCED ON ] SPC FB E/D Enable/Disable Front Panel Buttons SPC FHPD ON/OFF Set Forced HPD ON/OFF SPC DF Reset to Factory Defaults Using ias Intelligent Auto Sense Intelligent Auto Sense (ias ) will automatically switch inputs when a Hot Plug Detect signal becomes active on an input. ias can be enabled and disabled via IR or control. Please note that many common sources, such as a cable or satellite boxes, will emit Hot Plug Detect signals when in stand-by mode and may prevent full functionality of ias. When the blue Auto button on the IR remote is pressed or the SPC AS ON command is sent, ias will be activated on the KD-HD ProK unit. NOTE: ias will be disabled when the input button on the front of the unit is pressed to switch inputs or if any of the input select/scroll buttons on the IR remote are pressed. Specifications Technical: Input (Each): Connector, Type A, 19 Pin Female Output: Connector, Type A, 19 Pin Female Bandwidth: TMDS bandwidth 3.4 Gb/s Control: Front panel push buttons and LEDs; front/rear IR sensors; Wired IR - rear 3.5 mm female mini-stereo connector; - DB9 Female connector for Tx, Rx and ground Deep Color Support: Digital video formats in Deep Color Mode up to 12 bits/color and HDCP Licensing: Fully licensed and compatible with all and HDCP techologies Compliance with Standards: Supports all versions of and HDCP Link: Single Link - 4K/3D/1080p/60, 12 bit color depth, 1920x1200 max.

6 8 9» : 16 Default EDID settings. EDID information is assigned to the inputs from the internal EDID library or from a display s internal EDID data» Lossless Compressed Digital : Supports Dolby TrueHD, Dolby Digital Plus and DTS-HD Master» DDC Signal (Data): Input DDC Signal - 5 Volts p-p (TTL)» Video/ Signal: Input Video Signal Volts p-p» DDC Communication: EDID and HDCP Bi-directional Transparency from Display to Source» Wired IR: modulated IR signal input, 0-5V TTL or -10to +10V.» Power: 5 Volt 2 Amp, VAC, Hz General:» Regulation: CE, RoHS, WEEE» Enclosure: Black Metal» Product Dimensions: 8.2 x 1.67 x 3.9» Shipping Dimensions: 11.6 x 6.9 x 4.9» Product Weight: 2 lbs» Shipping Weight: 5 lbs Important Product Warnings: 1. Connect all cables before providing power to the unit. 2. Test for proper operation before securing unit behind walls or in hard to access spaces. 3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper screw support with bolts or sheet-rock anchors. Safety Instructions: Please be sure to follow these instructions for safe operation of your unit. 1. Read and follow all instructions. 2. Heed all warnings. 3. Do not use this device near water. 4. Clean only with dry cloth. 5. Install in accordance with the manufacturer s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way including:» Damage to the power supply or power plug» Exposure to rain or moisture Power Supply Use: You MUST use the Power Supply provided with your unit or you VOID the Key Digital Warranty and risk damage to your unit and associated equipment. Power Supply Use: You MUST use the Power Supply provided with your unit or you VOID the Key Digital Warranty and risk damage to your unit and associated equipment. How to Contact Key Digital Technical Support For technical questions about using Key Digital products, please contact us at: Phone: tech@keydigital.com Repairs and Warranty Service Should your product require warranty service or repair, please obtain a Key Digital Return Material Authorization (RMA) number by contacting us at: Phone: rma@keydigital.com Feedback Please any comments/questions about the manual to: customersupport@keydigital.com Warranty Information All Key Digital products are built to high manufacturing standards and should provide years of trouble-free operation. They are backed by a Key Digital Limited 3 Year Product Warranty Policy.»