Panel Bus I/O Modules

Transcription

1 Panel us I/O Modules GENERL The Honeywell Panel us I/O Modules communicate via the Panel us. The pluggable Honeywell Panel us I/O modules consist of a terminal socket and a removable electronic module, allowing the socket to be mounted and wired before the electronic module is installed. ll such electronic modules can be swapped out without disrupting the power and bus connections: Simply unplug the old and insert the new module. WRNING Risk of electric shock or equipment damage! Do not touch any live parts in the cabinet. Disconnect the power supply before you start to install the control system. More than one disconnect switch may be required to de-energize the system. Do not reconnect the power supply until you have completed the installation. Unused terminals must be closed (by completely screwing in the terminal screws), thus preventing the accidental touching of live parts. PRODUCT DT FETURES Plug-and-play functionality for easy maintenance. Pluggable Panel us I/O modules can be exchanged without rewiring. Further, the separate installation of terminal sockets and electronic modules lower risk of damage and theft in the construction phase. Fast wiring with state-of-the-art push-in terminals (screwtype terminals also available) and bridge connectors. Wide range of sensors supported (NTC0kΩ, NTC0kΩ, PT000-/-, Johnson 99 PTC, NI000TK5000, PT3000, alco500, 0/ 0 V, 0/4 0 m). TE: The mixed Panel us I/O modules XF830, XFU830, and CPO- IO830 feature inputs suitable for signals from NTC0kΩ sensors and 0/ 0 V, 0/4 0 m, only! inary input LEDs of the pluggable Honeywell Panel us I/O Modules can be configured for status display (off / yellow) or alarm display (green / red) per channel. TE: The mixed I/O modules XF830, XFU830, and CPO- IO830 feature only non-configurable binary input LEDs! Configurable safety position for outputs, in case of loss of communication with the controller. Max. wiring flexibility due to optional accessories like aux. terminals, manual disconnectors, and cross-connectors. Can be mounted in small installation housings Flexible mix of Panel us I/O modules covering all your application requirements. The mixed Honeywell Panel us I/O modules offer a mix of 34 inputs and outputs in a compact housing. Software updates, configuration, and commissioning are all done automatically by the controller for all Panel us I/O Modules. The Panel us I/O Modules are addressed manually by adjusting their HEX switches. The Panel us I/O Modules may be used with any CPU supporting Panel us communication (e.g., the XL800, CPO- PC-6, etc.). U.S. Registered Trademark Copyright 06 Honeywell Inc. ll Rights Reserved EN0-070GE5 R06

2 Install. Instr. MU-0463GE5 inary Inputs nalog Inputs I5 I6 I7 I G G I I I3 I DI TM ComfortPoint Open nalog Outputs O5 O6 O7 O O O O3 O4 V Relays IN IN IN3 IN4 IN5 IN DO! PNEL US I/O MODULES PRODUCT DT OVERVIEW pluggable NLOG INPUT pluggable NLOG OUTPUT pluggable INRY INPUT pluggable RELY OUTPUT pluggable FLOTING OUTPUT MIXED I/Os (with integrated socket) PNEL US MODULES XFR8 XFR8 XFR85 XF830, XFU830 Honeywell XF8 XF8 XF83 XF8 CPO-IO830 CONTROLLER XS8- XSU8- Panel us XS83 XSU83 XS8-5 XSU8-5 Fig.. Overview of Honeywell Panel us I/O Modules Table. Overview of Honeywell Panel us I/O Modules order number description Pluggable Panel us I/O Modules XF8 Pluggable Panel us nalog Input Module (with 8 analog inputs) XF8 XFR8 XF83 XF8 XFR8 XFR85 Pluggable Panel us nalog Output Module (with 8 analog outputs) Pluggable Panel us nalog Output Module (with 8 analog outputs and manual overrides) Pluggable Panel us inary Input Module (with binary inputs) Pluggable Panel us Relay Output Module (with 6 relay outputs) Pluggable Panel us Relay Output Module (with 6 relay outputs and manual overrides) Pluggable Panel us Floating Output Module (with 3 floating outputs and manual overrides) Mixed Panel us I/O Modules with integrated socket XF830 XFU830 XF830, XFU830, CPO-IO830 PNEL US I/O MODULES Mixed Panel us I/O Module (with 8 analog inputs, 8 analog outputs, binary inputs, and 6 relay outputs), with push-in terminals (incl. bridge connector and swivel label); housing matches XL800 design Mixed Panel us I/O Module (with 8 analog inputs, 8 analog outputs, binary inputs, and 6 relay outputs), with screw terminals (incl. bridge connector and swivel label); housing matches XL800 design Mixed Panel us I/O Module (with 8 analog inputs, 8 analog outputs, binary inputs, and 6 relay outputs), with CPO-IO830 push-in terminals (incl. bridge connector); housing matches CPO-PC-6 design Terminal Sockets (not needed for the mixed I/O modules XF830, XFU830, and CPO-IO830) XS8- Push-in terminal socket for pluggable I/O modules (incl. bridge connector, swivel label) XSU8- XS83 XSU83 XS8-5 XSU8-5 Screw-type terminal socket for pluggable I/O modules (incl. bridge connector, swivel label) Push-in terminal socket for pluggable I modules (incl. bridge connector, swivel label) Screw-type terminal socket for pluggable I modules (incl. bridge connector, swivel label) Push-in terminal socket for pluggable relay/floating output modules (incl. bridge connector, cross connector, swivel label) Screw-type terminal socket for pluggable relay/floating output modules (incl. bridge connector, cross connector, swivel label) EN0-070GE5 R06

3 PNEL US I/O MODULES PRODUCT DT order number XS8 Table. Overview of auxiliary parts and spare parts description Manual Disconnector Module for I/O/I Modules (for manual disconnection of individual signals; useful during start-up). Plugged between Terminal Socket and Electronic Module. For pluggable I/O modules, only. XS8RO Manual Disconnector Module for Relay Output Modules (for manual disconnection of individual signals; useful during start-up). Plugged between Terminal Socket and Electronic Module. Not suitable for line voltage. For pluggable I/O modules, only. XS84 XS XS G G XS85 XS86 Ten uxiliary Terminal locks (for distribution of signals/power). Each terminal block includes two groups with seven internally-connected push-in terminals. For pluggable I/O modules, only. Ten uxiliary Terminal locks (for distribution of signals/power). Each terminal block consists of two groups of nine internally-connected push-in terminals. For XF830 and XFU830, only. Ten uxiliary Terminal locks (for connection of 0 0 m signals). Each terminal block supports up to 8 current inputs. For XF830 and XFU830, only. 0 Cross-Connectors for connection of six relay commons. One Cross-Connector is included in the Terminal Socket package. For pluggable I/O modules, only. 0 ridge Connectors. One ridge Connector is included in the Terminal Socket package. XL0 XL 0 Swivel Labels Holders (for attaching the application-specific label printed with CRE). One Swivel Label Holder is included in each Terminal Socket package. For pluggable I/O modules, only. 0 Swivel Label Holders for XF830 and XFU830 mixed Panel us I/O modules. One Swivel Label Holder is included in each package of XF830 and XFU830 mixed Panel us I/O modules. TE: ll Honeywell Panel us I/O Modules (pluggable and mixed) are protected against short circuit, Vac +0% and 30 Vdc. 3 EN0-070GE5 R06

4 PNEL US I/O MODULES PRODUCT DT Table 3. Pluggable Panel us I/O Module specifications Module nalog Input nalog Output inary Input Relay Output Floating Output XF8 XF8, XFR8 XF83 XF8, XFR8 XFR85 no. of I/Os 8 analog inputs 8 analog outputs binary inputs 6 relay outputs 3 floating outputs requiring a gold contact or open collector characteristics floating outputs Linear Graph, 0..0 Vdc with pullup, 0() 0 Vdc without pull-up NTC0kΩ ( C, default) NTC0kΩ ( C) PT000- ( C) PT000- (0 400 C) Johnson 99 ( C) NI000TK5000 ( C) PT3000 ( C) LCO500 (-30 0 C) lso configurable as: binary inputs Linear graph (0 0 V with pull-up) Features: 6-bit resolution configurable offset per input auxiliary voltage: 0 Vdc, Imax = 5 m 0 Vdc / m lso configurable as: floating outputs or binary outputs (0 V / 0 V) Features: 8-bit resolution (default) Safety position (remain, 0%, 50%, 00%) red LED per output light intensity follows output level in auto Version with manual override (R): potentiometer per output auto feedback signal (mode + value) blinking in manual override position static binary input, (default: dry contact) lso configurable as: totalizers (0 Hz) Features: LED per input Color mode can be set per input to OFF/yellow or green/red using CRE ON: <.6 kω to or <.5 V to, OFF: > 90 kω to or > 4 V to relay outputs (default) Features: Changeover relays Voltage: 9 50 Vac, 9 Vdc, P>50 mw max. total current: current per relay: N.O.: 4(4) (C) or 4() (DC), N.C.: () (C) or 4() (DC) Safety position (remain, 0%, 00%) yellow LED per output With man. override (R): switch per output auto feedback signal (mode + value) blinking in manual override position Features: relays per floating output Voltage: 9 50 Vac, 9 Vdc, P>50 mw max. total current: current per relay: N.O.: 4(4) (C) or 4() (DC), N.C.: () (C) or 4() (DC) potentiometer per floating output LEDs per output: green: relay closed, red: relay closed blinking in manual override position auto feedback signal (mode + value) Manual Overrides as per EN ISO 6484-:004 The manual override switches and potentiometers of the output modules ( R8, R8, and XFR85) support direct operation as per EN ISO 6484-:004, section "Local Priority Override/Indicating Units." Specifically, the positions of the manual override switches and potentiometers directly control the outputs independently of the controller and HMI. When a manual override switch or potentiometer is not in its default position ("auto"), the corresponding output LED will blink continuously, and the output module will send a feedback signal with the status "manual override" and the given override position to the controller (which will then also store this information in its alarm memory). TE: When updating the firmware of output modules, their outputs are turned OFF regardless of the position of their manual override switches and/or potentiometers. Configurable types: NTC0kΩ ( C) (default) Linear Graph 0..0 Vdc with pull-up 0() 0 Vdc without pull-up lso configurable as: binary inputs (static, dry contact, only) Features: 0-bit resolution configurable offset per input Table 4. Mixed Panel us I/O module specifications (XF830, XFU830, and CPO-IO830) nalog Inputs nalog Outputs inary Inputs Relay Outputs Number: 8 Number: 8 Number: (requiring a gold Number: 6 contact or open collector) Configurable types: 0 Vdc / m (default) lso configurable as: binary outputs (0 V / 0 V) Features: 0-bit resolution (default) Safety position (remain, 0%, 50%, 00%) Configurable types: Static binary inputs (default: static, dry contact); ON: <.6 kω to or <.5 V to, OFF: > 90 kω to or > 4 V to lso configurable as: totalizers (5 Hz) Features: yellow LED per input Configurable types: Relay outputs (default) Features: Voltage: Vac/dc, P>50 mw max. total current: 3 (ac/dc) current per relay: 500 m normally-open contacts: P > 50 mw, voltage: V (ac/dc) yellow LED per output EN0-070GE5 R06 4

5 7 a 7 b UTO! VUX VUX a 7 b I/O I/O ! 0 UTO! 00 I :CDFERTQWESDERT :CDFERTQWESDERT 3:CDFERTQWESDERT3 4:CDFERTQWESDERT4 5:CDFERTQWESDERT5 6:CDFERTQWESDERT6 7:CDFERTQWESDERT7 8:CDFERTQWESDERT UTO! a 7 b ! PNEL US I/O MODULES PRODUCT DT GENERL FETURES S CDEF0 S PRESS Honeywell Honeywell PRESS S S CDEF0 CDEF0 S S 3 Honeywell Honeywell Honeywell PRESS PRESS PRESS PRESS S CDEF0 S System Constraints Max. no. of I/O modules (any combination) per controller Table 5. System constraints depends upon controller type Max. no. of I/O modules per row 0 Max. current () Max. current (F) Max. current (F3) Max. row length Max. distance between rows Min. cross-section of (terminal 9) (protected by F) 4 3 m 40 m.5 mm 6 7 Fig.. Panel us I/O Modules on DIN rails Legend Controller (e.g., XL800, XL Web II, CPO-PC-6, etc.) Cable (power and LONWORKS) connection from controller to Panel us I/O Modules 3 Swivel label holder 4 Cable connection between Panel us I/O Modules on separate DIN rails 5 ridge connectors between Panel us I/O Modules on same DIN rail 6 Stopper (from 3 rd -party supplier) 7 uxiliary terminal packages LEDs Each Honeywell Panel us I/O Module is equipped with: one green power LED one yellow service LED Overvoltage Protection ll inputs and outputs are protected against Vac and 40 Vdc overvoltage as well as against short-circuiting. Service LED Each Panel us I/O Module is equipped with a yellow service LED (status: yellow/off) for easy diagnosis of failures. Microprocessor Each Panel us I/O Module is equipped with its own microprocessor. System Constraints Depending upon the given controller, up to 64 I/O modules in any combination of models may be connected. ddressing ddressing is performed using the HEX switch. 5 EN0-070GE5 R06

6 PNEL US I/O MODULES PRODUCT DT nalog Input Module 0 VDC.9 kohm I Vi 99.9 kohm (8.9 VDC IF CONNECTION INTERRUPTED) Fig. 6. nalog input impedance setpoint (input circuit for NTC0kΩ, NTC0kΩ, wall module setpoint) 3 Fig. 3. XF8 Panel us I Module (shown with terminal socket) Legend Hex switch S Service LED 3 Power LED The pluggable Honeywell Panel us nalog Input Module, with 8 analog inputs, is installed with the XS8- or XSU8- Terminal Socket. ccessory disconnector module: XS8 (see also Table on page 3). RTD I 0 VDC.9 kohm Fig. 4. nalog input low impedance (input circuit for PT000, Johnson 99 PTC, alco500, PT3000, NI000TK5000, slow binary input) I VUX 9 VUX 0 I I I3 I4 I5 I6 I7 I Fig. 7. Terminal assignment and internal connections Features 0 0 Vdc, 0 Vdc without pull-up 0 0 Vdc with pull-up (linear graph, e.g. used for wall module connection) 0/4 0 m, needs 499 Ω resistor in parallel NTC0kΩ ( C, default) NTC0kΩ ( C) PT000- ( C) PT000- ( C) NI000TK5000 ( C) PT3000 ( C) LCO500 ( C) inary input 6-bit resolution Configurable offset per input uxiliary voltage: 0 Vdc, IMX = 5 m Sensor failure detection Vi 99.9 kohm Fig. 5. nalog input high impedance (input circuit for voltage input for active sensors) EN0-070GE5 R06 6

7 PNEL US I/O MODULES PRODUCT DT XF8 NLOG INPUT MODULE VUX VUX I I I3 I4 I5 I6 I7 I XF... SHIELD INTERNLLY CONNECTED TO DIN RIL OPT. UX. TERMINL MODULE XS EXTERNL GROUND REQUIRED TO POWER EXTERNL DEVICES ( VC) F CTIVE SENSOR : V ~ POWER : VDC SIGNL 3: ( 0) 3 3 UX. VOLTGE + POT. : SIGNL : 3: 0 VDC UX. LEGEND: F THIN LINES THICK LINES DSHED LINES MX. 4 MX. MIN mm MIN..5 mm SELECTED INTERNL CONNECTIONS Fig. 8. XF8 Panel us I Module, wiring example : ctive sensor and potentiometer 7 EN0-070GE5 R06

8 PNEL US I/O MODULES PRODUCT DT XF8 NLOG INPUT MODULE XF... VUX VUX I I I3 I4 I5 I6 I7 I XF... SHIELD INTERNLLY CONNECTED TO DIN RIL EXTERNL DC POWER SUPPLY EXTERNL 499 OHM RESISTOR WITH TWIN WIRE-END FERRULES REQUIRED. DRY CONTCT : SIGNL : DRY CONTCT TEMP. SENSOR (NTC0k or Pt000) 0(4)...0 m : IN : OUT LEGEND: F THIN LINES THICK LINES DSHED LINES MX. 4 MX. MIN mm MIN..5 mm SELECTED INTERNL CONNECTIONS Fig. 9. XF8 Panel us I Module, wiring example : Passive sensor and 0 (4) 0 m signal EN0-070GE5 R06 8

9 PNEL US I/O MODULES PRODUCT DT nalog Output Modules ccessory disconnector module: XS8 (see also Table on page 3) O O O3 O4 O5 O6 O7 O Fig. 0. XFR8 Panel us O Module (shown with terminal socket) Legend Hex switch S Manual overrides 3 Status LEDs 4 Service LED 5 Power LED The pluggable Honeywell Panel us nalog Output Modules, with 8 analog outputs, are available in the following models: XF8 Panel us nalog Output Module (without manual overrides) XFR8 Panel us nalog Output Module (with manual overrides) They are installed with the XS8- or XSU8- Terminal Socket. Fig.. Terminal assignment and internal connections Features 0 Vdc, +/- m Floating actuator (requires MCD3) inary output (0 V / 0 V) red LED per output (brightness according to signal level) Optional versions with manual override potentiometers (uto, 0 00%; LED flashes in override mode) Feedback on manual override signal 8-bit resolution Configurable safety position for outputs in case of communication problems (remain, 0%, 50%, 00%) 9 EN0-070GE5 R06

10 PNEL US I/O MODULES PRODUCT DT XF8 NLOG OUTPUT MODULE OOO3O4O5O6O7O XF SHIELD INTERNLLY CONNECTED TO DIN RIL EXT. GROUND REQUIRED TO POWER EXT. DEVICES OPT. UX. TERMINL MODULE XS ( VC) XS84 F LEGEND: V ~ DRIVE WITH VDC SIGNL : V ~ POWER : ( 0) 3: VDC SIGNL 3 M F THIN LINES THICK LINES DSHED LINES MX. 4 MX. MIN mm MIN..5 mm SELECTED INTERNL CONNECTIONS Fig.. XF8 Panel us O Module, wiring example : ctuator EN0-070GE5 R06 0

11 PNEL US I/O MODULES PRODUCT DT XF8 NLOG OUTPUT MODULE OOO3O4O5O6O7O XF SHIELD INTERNLLY CONNECTED TO DIN RIL EXT. GROUND REQUIRED TO POWER EXT. DEVICES OPT. UX. TERMINL MODULE XS ( VC) XS84 F LEGEND: MX. 4 V ~ DRIVE WITH VDC SIGNL : V ~ POWER : ( 0) 3: VDC SIGNL M MCD 3 K K K3 F MX THIN LINES THICK LINES DSHED LINES MIN mm MIN..5 mm SELECTED INTERNL CONNECTIONS L N 3 M M Fig. 3. XF8 Panel us O Module, wiring example : Relay Module MCD 3 The relay module facilitates the control of peripheral devices with high load via the analog outputs. Input terminal 7 of MCD3 controls changeover contact K3. Relay terminal 8 of MCD3 controls the N.O. contacts (floating outputs) K, K. EN0-070GE5 R06

12 PNEL US I/O MODULES PRODUCT DT XF8 NLOG OUTPUT MODULE OOO3O4O5O6O7O XF SHIELD INTERNLLY CONNECTED TO DIN RIL EXT. GROUND REQUIRED TO POWER EXT. DEVICES OPT. UX. TERMINL MODULE XS ( VC) XS84 F LEGEND: MX. 4 V ~ DRIVE WITH VDC SIGNL : V ~ POWER : ( 0) 3: VDC SIGNL 3 M MCE 3 K K K3 F MX THIN LINES MIN mm THICK LINES MIN..5 mm DSHED LINES SELECTED INTERNL CONNECTIONS Fig. 4. XF8 Panel us O Module, wiring example 3: Relay Module MCE 3 The relay module facilitates the control of peripheral devices with high load via the analog outputs. Input terminal 6 of MCE3 controls the N.O. contact K3. Input terminal 7 of MCE3 controls the changeover contact K. Input terminal 8 of MCE3 controls the changeover contact K. EN0-070GE5 R06

13 PNEL US I/O MODULES PRODUCT DT inary Input Module Features Static binary input (dry contact) Totalizer for up to 0 Hz LEDs per binary input supporting alarm display mode (red/green) or status mode (off/yellow). Color mode of each LED can be set to OFF/yellow or green/red in CRE. Configuration as Fast Totalizer Using CRE, the binary inputs can be configured as fast totalizers for operation in conjunction with devices equipped with an open collector output. Table 6. inary inputs used as fast totalizers Frequency max. 0 Hz 3 4 Fig. 5. XF83 Panel us I Module (shown with XS83 terminal socket) Pulse ON Pulse OFF ounce min. 5 ms min. 5 ms max. 5 ms Legend Hex switch S Status LEDs 3 Service LED 4 Power LED The pluggable Honeywell Panel us inary Input Module, with binary inputs, is installed with the XS83 or XSU83 Terminal Socket. ccessory disconnector module: XS8 (see also Table on page 3). I +V 8 VDC (T STILIZED) 0 kohm 50 kohm DRY CONTCT VDC = OPEN 0... VDC = CLOSED I I I3 I4 I5 I6 I7 I8 I9 I0 I I FST TOTLIZER Fig. 7. Configuration of binary input as fast totalizer Fig. 6. Terminal assignment and internal connections 3 EN0-070GE5 R06

14 PNEL US I/O MODULES PRODUCT DT XF83 INRY INPUT MODULE I I I3 I4 I5 I6 I7 I8 I9 I0 II XF... SHIELD INTERNLLY CONNECTED TO DIN RIL DRY CONTCT : SIGNL : DRY CONTCT TOTLIZER : SIGNL : MIN. 5 ms TOTLIZER LEGEND: THIN LINES THICK LINES DSHED LINES MX. 4 MIN mm MIN..5 mm SELECTED INTERNL CONNECTIONS Fig. 8. XF83 Panel us I Module, wiring example: Dry contact and totalizer EN0-070GE5 R06 4

15 PNEL US I/O MODULES PRODUCT DT Relay Output Modules RELY LOCK RELY LOCK REMOVLE CROSS CONNECTOR (FCTORY-MOUNTED) Fig. 9. XFR8 Panel us Relay Output Module (shown with terminal socket) Legend Hex switch S Manual overrides 3 Status LEDs 4 Service LED 5 Power LED The pluggable Honeywell Panel us Relay Output Modules, with 6 relay outputs, are available in the following versions: XF8 Panel us Relay Output Module (without manual overrides) XFR8 Panel us Relay Output Module (with manual overrides) They are installed with the XS8-5 or XSU8-5 Terminal Socket. ccessory disconnector module: XS8-RO (see also Table on page 3). Fig. 0. Terminal assignment and internal connections Features - Cross-Connecter - yellow LED per output - Optional versions with manual override switches (uto, 0, ; LED flashes in override mode) - Feedback on manual override signal - Configurable safety position for outputs in case of communications problems (remain, OFF, ON) - Permissible Load per Relay Output Module (Total) Max. load: 9 50 Vac: Vdc: resistive, 3 inductive - Permissible Load per Normally-Open Contact: Max. load: 9 50 Vac: 4 resistive or inductive Vdc: 4 resistive, inductive Min. load: P > 50 mw - Permissible Load per Normally-Closed Contact: Max. load: 9 50 Vac: resistive, inductive Vdc: resistive, inductive Min. load: P > 50 mw 5 EN0-070GE5 R06

16 PNEL US I/O MODULES PRODUCT DT XF8 RELY OUTPUT MODULE XF... CROSS CONNECTOR XS85 (FCTORY-MOUNTED) SHIELD INTERNLLY CONNECTED TO DIN RIL OPTIONL UX. TERMINL PCKGE XS F3 L N POWER SUPPLY 30 VC FIELD DEVICE : 30 V (N) : 30 V (L) M 30 V FIELD DEVICE : 30 V (N) : 30 V (L) M 30 V LEGEND: MX. 4 F3 MX. THIN LINES MIN mm THICK LINES MIN..5 mm - or less, as per F3 DSHED LINES SELECTED INTERNL CONNECTIONS Fig.. XF8 Panel us RO Module, wiring example : oth relay blocks with line voltage EN0-070GE5 R06 6

17 PNEL US I/O MODULES PRODUCT DT XF8 RELY OUTPUT MODULE XF... CROSS CONNECTOR XS85 (FCTORY-MOUNTED) SHIELD INTERNLLY CONNECTED TO DIN RIL OPTIONL UX. TERMINL PCKGE XS F3 L N POWER SUPPLY 30 VC FIELD DEVICE : 30 V (N) : 30 V (L) M 30 V FIELD DEVICE : 30 V (N) : 30 V (L) M 30 V FIELD DEVICE : 30 V (N) : 30 V (L) M 30 V LEGEND: MX. 4 F3 MX. THIN LINES MIN mm THICK LINES MIN..5 mm - or less, as per F3 DSHED LINES SELECTED INTERNL CONNECTIONS Fig.. XF8 Panel us RO Module, wiring example : Relay blocks with low and line voltage 7 EN0-070GE5 R06

18 PNEL US I/O MODULES PRODUCT DT Floating Output Module CTUTOR CTUTOR CTUTOR REMOVLE CROSS CONNECTOR (FCTORY-MOUNTED) Fig. 3. XFR85 Panel us Floating Output Module (shown with socket) Legend Hex switch S Manual overrides 3 Status LEDs 4 Service LED 5 Power LED The pluggable XFR85 Panel us Floating Output Module, with manual overrides and 3 floating outputs, is installed with the XS8-5 or XSU8-5 Terminal Socket. ccessory disconnector module: XS8-RO (see also Table on page 3). Fig.. Terminal assignment and internal connections Features - Cross-Connecter - red LED (opening) and green LED (closing) per floating output - Manual override potentiometers (uto, 0%...00%; LED flashes in override mode) - Feedback on manual override signal - Configurable safety position for outputs in case of communication problems (remain, 0%, 50%, 00%) - Permissible Load per Floating Output Module (Total) Max. load: 9 50 Vac: Vdc: resistive, 3 inductive - Permissible Load per Normally-Open Contact: Max. load: 9 50 Vac: 4 resistive or inductive Vdc: 4 resistive, inductive Min. load: P > 50 mw - Permissible Load per Normally-Closed Contact: Max. load: 9 50 Vac: resistive, inductive Vdc: resistive, inductive Min. load: P > 50 mw EN0-070GE5 R06 8

19 PNEL US I/O MODULES PRODUCT DT XFR85 FLOTING OUTPUT MODULE CON 4 CON CON 34 CON 44 CON 54 CON 64 XF... CROSS CONNECTOR XS85 (FCTORY-MOUNTED) SHIELD INTERNLLY CONNECTED TO DIN RIL OPTIONL UX. TERMINL PCKGE XS F3 L N 3 POWER SUPPLY 30 VC M FLOTING CTUOR WITH 30VC (REQUIRES TWO RELYS) : : 3: N LEGEND: MX. 4 F3 MX. THIN LINES MIN mm THICK LINES MIN..5 mm - or less, as per F3 DSHED LINES SELECTED INTERNL CONNECTIONS Fig. 5. XFR85 Panel us FO Module, wiring example: Floating actuator 9 EN0-070GE5 R06

20 0 F 0 F PNEL US I/O MODULES PRODUCT DT Mixed I/O Modules XF830 XFU830 CPO-IO G G Fig. 6. XF830, XFU830, and CPO-IO830 Mixed Panel us Modules The mixed Honeywell Panel us I/O modules, with 8 analog inputs, 8 analog outputs, binary inputs, and 6 relay outputs, are available in the following versions: XF830 mixed Honeywell Panel us I/O module, with push-in terminals; XFU830 mixed Honeywell Panel us I/O module, with screw terminals; CPO-IO830 mixed Honeywell Panel us I/O module, with push-in terminals. Each features an integrated terminal socket and electronic module. The XF830 can be equipped with up to two rows of (XS830 and/or XS83) auxiliary terminal blocks on the top and/or bottom. The XFU830 and CPO-IO830 can be equipped with up to two rows of (XS830 and/or XS83) auxiliary terminal blocks on the top, only. Honeywell inary Inputs TM ComfortPoint Open Install. Instr MU-0463GE5 DI nalog Inputs I5 I6 I7 I I I I3 I4 G G 4 4 nalog Outputs O5 O O6 O O7 O3 O O4 V Relays IN IN IN3 IN4 IN5 IN Fig. 9. CPO-IO830 mixed Panel us I/O module, shown with 4 optional aux. terminal blocks (top view) Features - yellow LED per output - Configurable safety position for outputs in case of communications problems (remain in last position, OFF, ON) WRNING DO! 7 a External a V 7 b b S E D 3 4 C V for relay J J J3 J4 J5 Risk of electric shock or equipment damage! It is not permitted to wire the relays of the mixed Panel us I/O modules for anything other than low voltage. Install. Instr. EN-0375GE5 XF830 I / 8 I / 8 O / 6 RO V, 5V, T X000-XFU830 8 Made in Germany 053 inary Inputs DI nalog Inputs I5 I6 I7 I G G I I I3 I nalog Outputs V Relays O5 O6 O7 O8 IN IN IN3 IN4 IN5 IN O O O3 O DO Honeywell G G Fig. 7. XF830 mixed Panel us I/O module, shown with 4 optional aux. terminal blocks (top view) 7 a External a V 7 b b S E D 3 4 C V for relay...5 J J J3 J4 J ! Permissible Loads Table 7. Permissible loads of mixed Panel us I/O modules per module (total for all relay contacts) per normally open contact max. load VDC/VC 3 resistive or inductive, cos φ 0.6, no capacitive load, protected by fuse F4 VDC/VC, 0.5 resistive or inductive, cos φ 0.6, no capacitive load min. load >50 mw, 0.05 res./ind., cos φ 0.6 inary Inputs nalog Inputs nalog Outputs V Relays I5 I6 I7 I8 O5 O6 O7 O8 IN IN IN3 IN4 IN5 IN G G I I I3 I4 4 4 O O O3 O Honeywell Install. Instr. EN-0375GE DI DO! XFU830 I / 8 I / 8 O / 6 RO V, 5V, T X000-XFU Made in Germany Fig. 8. XFU830 mixed Panel us I/O module, shown without optional aux. terminal blocks (top view) EN0-070GE5 R06 0

21 PNEL US I/O MODULES PRODUCT DT I +V 8 VDC (T STILIZED) 0 kohm Vi 99.9 kohm I 50 kohm DRY CONTCT 6... VDC = OPEN 0... VDC = CLOSED Fig. 30. nalog input high impedance (input circuit for voltage input for active sensors) FST TOTLIZER 0 VDC Fig. 3. Configuration of a binary input as a fast totalizer.9 kohm I Vi 99.9 kohm (8.9 VDC IF CONNECTION INTERRUPTED) Fig. 3. nalog input impedance setpoint (input circuit for NTC0kΩ, NTC0kΩ, wall module setpoint) EN0-070GE5 R06

22 PNEL US I/O MODULES PRODUCT DT XF830 Mixed I/O Module INRY INPUTS NLOG INPUTS NLOG OUTPUTS V RELYS I5 I6 I7 I O5 O6 O7O IN IN IN3 IN4 IN5 IN I I I3 I G G 4 4 OOO3O XS OPT. UX. TERM. MODULE XS () ( VC) ( VC) VDC M VDC M DRY CONTCT : : SIGNL DRY CONTCT : : SIGNL TOTLIZER : : SIGNL NTC0kOHM SENSOR : : SIGNL CTIVE SENSOR : ( 0) : V ~ POWER 3: VDC F DRIVE with 0...0V SIGNL : ( 0) : V ~ POWER 3: VDC F4 DC : 0 : LEGEND: MX. 4 F MX. THIN LINES THICK LINES F4 MX. 3 MIN mm MIN..5 mm - or less, as per F, F4 Fig. 33. XF830 mixed Panel us I/O Module, wiring example : ctuators EN0-070GE5 R06

23 PNEL US I/O MODULES PRODUCT DT G OPT. UX. TERM. MODULE XS G m 3 CTIVE SENSOR : ( 0) : V ~ POWER 3: m OPT. UX. TERM. MODULE XS OPT. UX. TERM. MODULE XS F CPO-IO830 Mixed I/O Module INRY INPUTS NLOG INPUTS NLOG OUTPUTS V RELYS I5 I6 I7 I O5O6O7O IN IN IN3 IN4 IN5 IN I I I3 I G G 4 4 OOO3O LEGEND: MX. 4 F MX. THIN LINES THICK LINES MIN mm MIN..5 mm - or less, as per F Fig. 34. CPO-IO830 Connection example (for current inputs) 3 EN0-070GE5 R06

24 PNEL US I/O MODULES PRODUCT DT pprovals, Certifications, and Standards pprovals and Certifications CE-approved Conforms to EN and EN Investigated according to United States Standard UL96 (USL-listed) as well as according to Canadian National Standard(s) C. (CNL-listed) Mounting Methods DIN-rail mounting (e.g., in control cabinet). Calculated Lifetime of Weakest Components MTF 3.7 years (under typical operating conditions) Classification according to EN Environmental conditions: For use in home (residential, commercial, and light-industrial) environments Pollution degree: Class Protection against shock: Class II Software class: Class Overvoltage category: II Classification according to EN6059 (Degree of Protection Provided by Enclosures) Classification: IP0 mbient Environmental Limits Operating temperature: Storage temperature: Humidity: C at 5 93% r.h C at 5 93% r.h. 5 93% r.h. non-condensing Current Requirements and Heat Dissipation The Panel us I/O Modules are equipped with highly-efficient switching power supplies which provide for relatively uniform power consumption over a wide range of supply voltages (see Table 8). The specific heat dissipation inside the modules amounts to less than W for all models. Table 8. Current requirements of Panel us I/O modules devices powered supply voltage Vac Vdc XF8 30 m 80 m XF8, XFR8 50 m 90 m XF83 80 m 30 m XF8, XFR8, XFR85 40 m 80 m XF830, XFU830, CPO-IO m 95 m Mechanical Housing Dimensions (H x W x D) The pluggable Panel us I/O Modules (mounted on Terminal Sockets) all have the dimensions: 0 X 90 X 93 mm (see also Fig. 35 on page 5). The XF830 and XFU830 mixed Panel us I/O Modules have the dimensions: 6 X 0 X 93 mm (see also Fig. 36 on page 5). The CPO-IO830 mixed Panel us I/O Module has the dimensions: 6 X 0 X 6 mm (see also Fig. 37 on page 6). Housing Material Plastic, flame-retardant EN0-070GE5 R06

25 0 F 7 PNEL US I/O MODULES PRODUCT DT Dimensions LOCK TERMINL SOCKET 0 REMOVLE ELECTRONIC MODULE SCREW-TYPE TERMINLS 38 XS84 ux. Terminal Package (optional) SWIVEL LEL HOLDER 5.5 Fig. 35. Pluggable Honeywell I/O Modules (example with manual overrides), incl. terminal socket, dimensions (in mm) 6 7 a External a V 7 b b V for relay...5 S 78 E D 3 C J J J3 J4 J5 9.5 inary Inputs nalog Inputs nalog Outputs V Relays Honeywell I5 I6 I7 I8 O5 O6 O7 O8 IN IN IN3 IN4 IN5 IN G G I I I3 I4 4 4 O O O3 O Install. Instr. EN-0375GE5 DI DO! 00 CLERE XF830 I / 8 I / 8 O / 6 RO V, 5V, T X000-XFU830 8 Made in Germany C D G G SWIVEL LEL HOLDER SCREW-TYPE TERMINLS (XFU830),, and C = XS830 ux. Terminal Packages (optional) D = XS83 ux. Terminal Package (optional) Fig. 36. XF830 (shown) and XFU830 mixed Honeywell I/O Module (example with 4 auxiliary terminal packages), dimensions (in mm) 5 EN0-070GE5 R06

26 PNEL US I/O MODULES PRODUCT DT Honeywell TM ComfortPoint Open 7 7 inary Inputs nalog Inputs I5 I6 I7 I I I I3 I4 G G 4 4 nalog Outputs O5 O6 O7 O O O O3 O4 V Relays IN IN IN3 IN4 IN5 IN Install. Instr. MU-0463GE DI DO! 6. Fig. 37. CPO-IO830 Mixed Honeywell I/O Modules, dimensions (in mm) Manufactured for and on behalf of the Environmental & Energy Solutions Division of Honeywell Technologies Sàrl, Rolle, Z.. La Pièce 6, Switzerland by its uthorized Representative: utomation and Control Solutions Honeywell GmbH öblinger Strasse 7 70 Schönaich, Germany Phone +49 (0) Fax +49 (0) EN0-070GE5 R06 Subject to change without notice