LonWorks Bus I/O Modules

Transcription

1 LonWorks Bus I/O odules Product Data GENERL The CentraLine LONWORKS Bus I/O odules communicate via the LONWORKS Bus. These pluggable CentraLine LONWORKS Bus I/O modules consist of a terminal socket and a removable electronic module, allowing the socket to be mounted and wired before the electronic module is installed. ll such electronic modules can be swapped out without disrupting the power and bus connections: Simply unplug the old and insert the new module. WRNING Risk of electric shock or equipment damage! Do not touch any live parts in the cabinet. Disconnect the power supply before you start to install the control system. ore than one disconnect switch may be required to de-energize the system. Do not reconnect the power supply until you have completed the installation. Unused terminals must be closed (by completely screwing in the terminal screws), thus preventing the accidental touching of live parts. FETURES Plug-and-play functionality for easy maintenance. Pluggable LONWORKS Bus I/O modules can be exchanged without rewiring. Further, the separate installation of terminal sockets and electronic modules lower risk of damage and theft in the construction phase. Fast wiring with state-of-the-art push-in terminals (screwtype terminals also available) and bridge connectors. Wide range of sensors supported (NTC0kΩ, NTC0kΩ, PT000-/-, Johnson PTC, NI000TK5000, PT3000, Balco500, 0/ 0 V, 0/4 0 m). Binary input LEDs of the CentraLine LONWORKS Bus I/O odules can be configured for status display (off / yellow) or alarm display (green / red) per channel. Configurable safety position for outputs, in case of loss of communication with the controller. ax. wiring flexibility due to optional accessories like auxiliary terminals, manual disconnectors, and crossconnectors. Can be mounted in small installation housings Flexible mix of LONWORKS Bus I/O modules covering all your application requirements. Software updates, configuration, and commissioning are all done automatically by the controller for all LONWORKS Bus I/O odules. The LONWORKS Bus I/O odules may be used with any CPU supporting LONWORKS Bus communication (e.g., the LION, EGLE, etc.). Copyright 06 Honeywell GmbH ll Rights Reserved EN0Z-080GE5 R

2 OVERVIEW pluggable NLOG INPUT pluggable NLOG OUTPUT pluggable BINRY INPUT pluggable RELY OUTPUT LonWorks BUS ODULES CLIOLR8 CLIOLR8 CLIOL8 CLIOL8 CLIOL83 CLIOL8 LonWorks Bus CONTROLLER XS8- XSU8- XS83 XSU83 XS8-5 XSU8-5 Fig.. Overview of CentraLine LonWorks Bus I/O odules Table. Overview of CentraLine LonWorks Bus I/O odules order number description LonWorks Bus I/O odules CLIOL8 LONWORKS Bus Bus nalog Input odule (with 8 analog inputs) CLIOL8 LONWORKS Bus Bus nalog Output odule (with 8 analog outputs) CLIOLR8 LONWORKS Bus Bus nalog Output odule (with 8 analog outputs and manual overrides) CLIOL83 LONWORKS Bus Bus Binary Input odule (with binary inputs) CLIOL8 LONWORKS Bus Bus Relay Output odule (with 6 relay outputs) CLIOLR8 LONWORKS Bus Bus Relay Output odule (with 6 relay outputs and manual overrides) Terminal Sockets XS8- Push-in terminal socket for I/O modules (incl. bridge connector, swivel label) XSU8- Screw-type terminal socket for I/O modules (incl. bridge connector, swivel label) XS83 Push-in terminal socket for BI modules (incl. bridge connector, swivel label) XSU83 Screw-type terminal socket for BI modules (incl. bridge connector, swivel label) XS8-5 Push-in terminal socket for relay/floating output modules (incl. bridge connector, cross connector, swivel label) XSU8-5 Screw-type terminal socket for relay/floating output modules (incl. bridge connector, cross connector, swivel label) EN0Z-080GE5 R036

3 order number XS8 Table. Overview of auxiliary parts and spare parts description anual Disconnector odule for I/O/BI odules (for manual disconnection of individual signals; useful during start-up). Plugged between Terminal Socket and Electronic odule. XS8RO anual Disconnector odule for Relay Output odules (for manual disconnection of individual signals; useful during start-up). Plugged between Terminal Socket and Electronic odule. Not suitable for line voltage. XS84 XS85 XS86 Ten uxiliary Terminal Blocks (for distribution of signals/power). Each terminal block includes two groups with seven internally-connected push-in terminals. 0 Cross-Connectors for connection of six relay commons. One Cross-Connector is included in the Terminal Socket package. 0 Bridge Connectors. One Bridge Connector is included in the Terminal Socket package. XL0 0 Swivel Labels Holders (for attaching the application-specific label printed with CRE). One Swivel Label Holder is included in each Terminal Socket package. NOTE: ll CentraLine LONWORKS Bus I/O odules are protected against short circuit, +0% and 30 Vdc Table 3. Pluggable LonWorks Bus I/O odule specifications odule nalog Input nalog Output Binary Input Relay Output CLIOL8 CLIOL8, CLIOLR8 CLIOL83 CLIOL8, CLIOLR8 no. of I/Os 8 analog inputs 8 analog outputs binary inputs requiring a gold contact or open collector 6 relay outputs characteristics Linear Graph, 0..0 Vdc with pull-up, 0() 0 Vdc without pull-up NTC0kΩ ( C, default) NTC0kΩ ( C) PT 000- ( C) PT 000- (0 400 C) Johnson PTC ( C) NI000TK5000 ( C) PT 3000 ( C) BLCO 500 (-30 0 C) lso configurable as: binary inputs Linear graph (0 0 V with pull-up) Features: 6-bit resolution configurable offset per input auxiliary voltage: 0 Vdc, I max = 5 m 0 Vdc / m lso configurable as: floating outputs or binary outputs (0 V / 0 V) Features: 8-bit resolution (default) Safety position (remain, 0%, 50%, 00%) red LED per output light intensity follows output level in auto Version with manual override (R): potentiometer per output auto feedback signal (mode + value) blinking in manual override position static binary input, (default: dry contact) lso configurable as: totalizers (0 Hz) Features: LED per input Color mode can be set per input to OFF/yellow or green/red using CRE ON: <.6 kω to or <.5 V to, OFF: > 0 kω to or > 4 V to relay outputs (default) Features: Changeover relays Voltage: 50 Vac, Vdc, P>50 mw max. total current: current per relay: N.O.: 4(4) (C) or 4() (DC), N.C.: () (C) or 4() (DC) Safety position (remain, 0%, 00%) yellow LED per output Version with manual override (R): switch per output auto feedback signal (mode + value) blinking in manual override position anual Overrides as per EN ISO 6484-:004 The manual override switches and potentiometers of the output modules support direct operation as per EN ISO :004, section "Local Priority Override/Indicating Units." Specifically, the positions of the manual override switches and potentiometers directly control the outputs independently of the controller and HI. When a manual override switch or potentiometer is not in its default position ("auto"), the corresponding output LED will blink continuously, and the output module will send a feedback signal with the status "manual override" and the given override position to the controller (which will then also store this information in its alarm memory). NOTE: When updating the firmware of output modules, their outputs are turned OFF regardless of the position of their manual override switches and/or potentiometers. 3 EN0Z-080GE5 R036

4 7 a 7 b UTO! VUX VUX 7 a 7 b I/O I/O ! 0 UTO! 00 BI :BCDFERTQWESDERT :BCDFERTQWESDERT 3:BCDFERTQWESDERT3 4:BCDFERTQWESDERT4 5:BCDFERTQWESDERT5 6:BCDFERTQWESDERT6 7:BCDFERTQWESDERT7 8:BCDFERTQWESDERT UTO! a 7 b 0! LONWORKS BUS I/O ODULES PRODUCT DT GENERL FETURES S BCDEF0 S PRESS Honeywell Honeywell PRESS S S BCDEF0 BCDEF0 S S 3 Honeywell Honeywell Honeywell PRESS PRESS PRESS PRESS S BCDEF0 S System Constraints ax. no. of I/O modules (any combination) per controller Table 4. System constraints depends upon controller type ax. no. of I/O modules per row 0 ax. current (F) ax. current (F) ax. current (F3) ax. row length ax. distance between rows in. cross-section of (terminal ) (protected by F) 4 3 m 40 m.5 mm 6 7 Fig.. LonWorks Bus I/O odules on DIN rails Legend Controller (e.g., LION, EGLE, HWK, etc.) Cable (power, LONWORKS) connection from controller to LONWORKS Bus I/O odules 3 Swivel label holder 4 Cable connection between LONWORKS Bus I/O odules on separate DIN rails 5 Bridge connectors between LONWORKS Bus I/O odules on same DIN rail 6 Stopper (from 3 rd -party supplier) 7 uxiliary terminal packages LEDs Each CentraLine LONWORKS Bus I/O odule is equipped with: one green power LED one yellow service LED Overvoltage Protection ll inputs and outputs are protected against Vac and 40 Vdc overvoltage as well as against short-circuiting. Service LED Each LONWORKS Bus I/O odule is equipped with a yellow service LED (status: yellow/off) for easy diagnosis of failures. LonWorks Service Button Each LONWORKS Bus I/O odule is equipped with a LONWORKS service button. icroprocessors Each LONWORKS I/O odule is equipped with an FTT-0 transceiver (link power-compatible) and can thus be used with any LONWORKS controller. In addition to the main microprocessor, the LONWORKS Bus I/O odules also have their own Neuron chip (30). EN0Z-080GE5 R036 4

5 nalog Input odule 0 VDC. koh I Vi. koh (8. VDC IF CONNECTION INTERRUPTED) Fig. 6. nalog input impedance setpoint (input circuit for NTC0kΩ, NTC0kΩ, wall module setpoint) 3 Fig. 3. CLIOL8 LonWorks Bus I odule (shown with terminal socket) Legend LONWORKS service button S Service LED 3 Power LED NOTE: The hex switch S (located next to the LONWORKS service S) has no function in combination with a LONWORKS Bus I/O module. It is used with Panel Bus I/O modules, only. The CentraLine LONWORKS Bus nalog Input odule, with 8 analog inputs, is installed with the XS8- or XSU8- Terminal Socket. ccessory disconnector module: XS8 (see also Table on page 3). RTD I 0 VDC. koh Fig. 4. nalog input low impedance (input circuit for PT000, Johnson PTC, Balco500, PT3000, NI000TK5000, slow binary input) I 7 75 B VUX VUX 0 I I I3 I4 I5 I6 I7 I Fig. 7. CentraLine LonWorks Bus nalog Input odule (schematic) Features 0 0 Vdc, 0 Vdc without pull-up 0 0 Vdc with pull-up (linear graph, e.g., used for wall module connection) 0/4 0 m, needs 4 Ω resistor in parallel NTC0kΩ ( C, default) NTC0kΩ ( C) PT000- ( C) PT000- ( C) NI000TK5000 ( C) PT3000 ( C) BLCO500 ( C) Binary input 6-bit resolution Configurable offset per input uxiliary voltage: 0 Vdc, I X = 5 m Sensor failure detection Vi. koh Fig. 5. nalog input high impedance (input circuit for voltage input for active sensors) 5 EN0Z-080GE5 R036

6 CLIOL8 NLOG INPUT ODULE B B VUX VUX I I I3 I4 I5 I6 I7 I CLIOL... SHIELD INTERNLLY CONNECTED TO DIN RIL OPT. UX. TERINL ODULE XS B B F EXTERNL GROUND REQUIRED TO POWER EXTERNL DEVICES ( VC) F CTIVE SENSOR : V ~ POWER : VDC SIGNL 3: ( 0) 3 3 UX. VOLTGE + POT. : SIGNL : 3: 0 VDC UX. LEGEND: F F THIN LINES THICK LINES DSHED LINES X. 4 X. IN mm IN..5 mm SELECTED INTERNL CONNECTIONS Fig. 8. CLIOL8 LonWorks Bus I odule, wiring example : ctive sensor and potentiometer EN0Z-080GE5 R036 6

7 B CLIOL8 NLOG INPUT ODULE B B VUX VUX III3I4 I5I6 I7I8 CLIOL CLIOL... SHIELD INTERNLLY CONNECTED TO DIN RIL EXTERNL DC POWER SUPPLY EXTERNL 4 OH RESISTOR WITH TWIN WIRE-END FERRULES REQUIRED. DRY CONTCT : SIGNL : DRY CONTCT TEP. SENSOR (NTC0k or Pt000) 0(4)...0 m : IN : OUT LEGEND: F F THIN LINES THICK LINES DSHED LINES X. 4 X. IN mm IN..5 mm SELECTED INTERNL CONNECTIONS Fig.. CLIOP8 LonWorks Bus I odule, wiring example : Passive sensor and 0 (4) 0 m signal 7 EN0Z-080GE5 R036

8 nalog Output odules They are installed with the XS8- or XSU8- Terminal Socket. ccessory disconnector module: XS8 (see also Table on page 3) B NC NC O O O3 O4 O5 O6 O7 O Fig. 0. CLIOPR8 LonWorks Bus O odule (shown with terminal socket) Legend LONWORKS service button S anual overrides 3 Status LEDs 4 Service LED 5 Power LED NOTE: The hex switch S (located next to the LONWORKS service S) has no function in combination with a LONWORKS Bus I/O module. It is used with Panel Bus I/O modules, only. The CentraLine LONWORKS Bus nalog Output odules, with 8 analog outputs, are available in the following models: CLIOL8 LONWORKS Bus nalog Output odule (without manual overrides) CLIOLR8 LONWORKS Bus nalog Output odule (with manual overrides) Fig.. CentraLine LONWORKS Bus nalog Output odules (schematic) Features 0 Vdc, +/- m Floating actuator (requires CD3) Binary output (0 V / 0 V) red LED per output (brightness according to signal level) Optional versions with manual override potentiometers (uto, 0 00%; LED flashes in override mode) Feedback on manual override signal 8-bit resolution Configurable safety position for outputs in case of communication problems (remain, 0%, 50%, 00%) EN0Z-080GE5 R036 8

9 CLIOL8 NLOG OUTPUT ODULE B B NC NC OOO3O4O5O6 O7O CLIOL SHIELD INTERNLLY CONNECTED TO DIN RIL EXT. GROUND REQUIRED TO POWER EXT. DEVICES OPT. UX. TERINL ODULE XS B B ( VC) XS84 F F LEGEND: V ~ DRIVE WITH VDC SIGNL : V ~ POWER : ( 0) 3: VDC SIGNL 3 F F THIN LINES THICK LINES DSHED LINES X. 4 X. IN mm IN..5 mm SELECTED INTERNL CONNECTIONS Fig.. CLIOL8 LonWorks Bus O odule, wiring example : ctuator EN0Z-080GE5 R036

10 CLIOL8 NLOG OUTPUT ODULE B B NC NC OOO3O4O5O6 O7O CLIOL SHIELD INTERNLLY CONNECTED TO DIN RIL EXT. GROUND REQUIRED TO POWER EXT. DEVICES OPT. UX. TERINL ODULE XS B B ( VC) XS84 F F LEGEND: F X. 4 V ~ DRIVE WITH VDC SIGNL : V ~ POWER : ( 0) 3: VDC SIGNL CD 3 K K K3 F X THIN LINES THICK LINES DSHED LINES IN mm IN..5 mm SELECTED INTERNL CONNECTIONS L N 3 Fig. 3. CLIOL8 LonWorks Bus O odule, wiring example : Relay odule CD 3 The relay module facilitates the control of peripheral devices with high load via the analog outputs. Input terminal 7 of CD3 controls changeover contact K3. Relay terminal 8 of CD3 controls the N.O. contacts (floating outputs) K, K. EN0Z-080GE5 R036 0

11 CLIOL8 NLOG OUTPUT ODULE B B NC NC OOO3O4O5O6 O7O CLIOL SHIELD INTERNLLY CONNECTED TO DIN RIL EXT. GROUND REQUIRED TO POWER EXT. DEVICES OPT. UX. TERINL ODULE XS B B ( VC) XS84 F F LEGEND: F X. 4 V ~ DRIVE WITH VDC SIGNL : V ~ POWER : ( 0) 3: VDC SIGNL CE 3 K K K3 F X THIN LINES IN mm THICK LINES IN..5 mm DSHED LINES SELECTED INTERNL CONNECTIONS Fig. 4. CLIOL8 Lonworks Bus O odule, wiring example 3: Relay odule CE 3 The relay module facilitates the control of peripheral devices with high load via the analog outputs. Input terminal 6 of CE3 controls the N.O. contact K3. Input terminal 7 of CE3 controls the changeover contact K. Input terminal 8 of CE3 controls the changeover contact K. EN0Z-080GE5 R036

12 Binary Input odule +V 8 VDC (NOT STBILIZED) 0 koh BI 50 koh DRY CONTCT VDC = OPEN 0... VDC = CLOSED 3 4 FST TOTLIZER Fig. 5. CLIOP83 LONWORKS Bus BI odule (shown with XS83 terminal socket) Legend LONWORKS service button S Status LEDs 3 Service LED 4 Power LED NOTE: The hex switch S (located next to the LONWORKS service S) has no function in combination with a LONWORKS Bus I/O module. It is used with Panel Bus I/O modules, only. The CentraLine LONWORKS Bus Binary Input odule, with binary inputs, is installed with the XS83 or XSU83 Terminal Socket. ccessory disconnector module: XS8 (see also Table on page 3). Fig. 6. Configuration of a binary input as a fast totalizer 7 75 B BI BI BI3 BI4 BI5 BI6 BI7 BI8 BI BI0 BI BI Fig. 7. CentraLine LONWORKS Bus Binary Input odules (schematic) Features Static binary input (dry contact) Totalizer for up to 0 Hz LEDs per binary input supporting alarm display mode (red/green) or status mode (off/yellow). Color mode of each LED can be set to OFF/yellow or green/red in CRE. EN0Z-080GE5 R036

13 F CLIOL83 BINRY INPUT ODULE B B BI BI BI3 BI4 BI5 BI6 BI7 BI8 BI BI0 BIBI CLIOL... SHIELD INTERNLLY CONNECTED TO DIN RIL DRY CONTCT : SIGNL : DRY CONTCT TOTLIZER : SIGNL : IN. 5 ms TOTLIZER LEGEND: F THIN LINES THICK LINES DSHED LINES X. 4 IN mm IN..5 mm SELECTED INTERNL CONNECTIONS Fig. 8. CLIOL83 LONWORKS Bus BI odule, wiring example: Dry contact and totalizer 3 EN0Z-080GE5 R036

14 Relay Output odules 7 75 B RELY BLOCK RELY BLOCK NO NC NO NC NO NC 3 3 NO NC 4 4 NO NC 5 5 NO NC REOVBLE CROSS CONNECTOR (FCTORY-OUNTED) Fig. 0. CentraLine LONWORKS Bus Relay Output odules (schematic) Fig.. CLIOLR8 LONWORKS Bus Relay Output odule (shown with terminal socket) Legend LONWORKS service button S anual overrides 3 Status LEDs 4 Service LED 5 Power LED The CentraLine LONWORKS Bus Relay Output odules, with 6 relay outputs, are available in the following versions: CLIOP8 LONWORKS Bus Relay Output odule (without manual overrides) CLIOPR8 LONWORKS Bus Relay Output odule (with manual overrides) They are installed with the XS8-5 or XSU8-5 Terminal Socket. ccessory disconnector module: XS8-RO (see also Table on page 3). Features - Cross-Connecter - yellow LED per output - Optional versions with manual override switches (uto, 0, ; LED flashes in override mode) - Feedback on manual override signal - Configurable safety position for outputs in case of communications problems (remain, OFF, ON) - Permissible Load per Relay Output odule (Total) ax. load (fuse F3): 50 Vac: Vdc: resistive, 3 inductive - Permissible Load per Normally-Open Contact: ax. load: 50 Vac: 4 resistive or inductive Vdc: 4 resistive, inductive in. load: P > 50 mw - Permissible Load per Normally-Closed Contact: ax. load: 50 Vac: resistive, inductive Vdc: resistive, inductive in. load: P > 50 mw EN0Z-080GE5 R036 4

15 F 7 CLIOL8 RELY OUTPUT ODULE B NO NC 3 NO NC 3 NO 3 NC 3 33 NO 4 NC 4 43 NO 5 NC 5 53 NO 6 NC 6 63 CLIOL... CROSS CONNECTOR XS85 (FCTORY-OUNTED) SHIELD INTERNLLY CONNECTED TO DIN RIL OPTIONL UX. TERINL PCKGE XS84 B B B3 B4 B5 B6 B7 F3 L N POWER SUPPLY 30 VC FIELD DEVICE : 30 V (N) : 30 V (L) 30 V FIELD DEVICE : 30 V (N) : 30 V (L) 30 V LEGEND: F X. 4 F3 X. THIN LINES IN mm THICK LINES IN..5 mm - or less, as per F3 DSHED LINES SELECTED INTERNL CONNECTIONS Fig.. CLIOL8 LONWORKS Bus RO odule, wiring example : Both relay blocks with line voltage 5 EN0Z-080GE5 R036

16 F 7 CLIOL8 RELY OUTPUT ODULE B NO NC 3 NO NC 3 NO 3 NC 3 33 NO 4 NC 4 43 NO 5 NC 5 53 NO 6 NC 6 63 CLIOL... CROSS CONNECTOR XS85 (FCTORY-OUNTED) SHIELD INTERNLLY CONNECTED TO DIN RIL OPTIONL UX. TERINL PCKGE XS84 B B B3 B4 B5 B6 B7 F3 L N POWER SUPPLY 30 VC FIELD DEVICE : 30 V (N) : 30 V (L) 30 V FIELD DEVICE : 30 V (N) : 30 V (L) 30 V FIELD DEVICE : 30 V (N) : 30 V (L) 30 V LEGEND: F X. 4 F3 X. THIN LINES IN mm THICK LINES IN..5 mm - or less, as per F3 DSHED LINES SELECTED INTERNL CONNECTIONS Fig.. CLIOL8 LONWORKS Bus RO odule, wiring example : Relay blocks with low and line voltage EN0Z-080GE5 R036 6

17 pprovals, Certifications, and Standards pprovals and Certifications CE-approved Conforms to EN 600- and EN Investigated according to United States Standard UL6 (USL-listed) as well as according to Canadian National Standard(s) C. (CNL-listed) Classification according to EN600- Environmental conditions: For use in home (residential, commercial, and light-industrial) environments Pollution degree: Class Protection against shock: Class II Software class: Class Overvoltage category: II Classification according to EN605 (Degree of Protection Provided by Enclosures) Classification: IP0 mbient Environmental Limits Operating temperature: Storage temperature: Humidity: C at 5 3% r.h C at 5 3% r.h. 5 3% r.h. non-condensing Current Requirement and Heat Dissipation The LONWORKS Bus I/O odules are equipped with highlyefficient switching power supplies which provide for relatively uniform power consumption over a wide range of supply voltages (see Table 5). The specific heat dissipation inside the modules amounts to less than W for all models. Table 5. Current requirements at nominal voltage devices powered supply voltage Vac Vdc CLIOL8 30 m 80 m CLIOL8, CLIOLR8 50 m 0 m CLIOL83 80 m 30 m CLIOL8, CLIOLR8 40 m 80 m echanical Housing Dimensions (H x W x D) The LONWORKS Bus I/O odules (mounted on Terminal Sockets) all have the dimensions: 0 X 0 X 3 mm (see also Fig. 3 on page 8). Housing aterial Plastic, flame-retardant ounting ethods DIN-rail mounting (e.g., in control cabinet). Calculated Lifetime of Weakest Components TBF 3.7 years (under typical operating conditions) 7 EN0Z-080GE5 R036

18 Dimensions LOCK SCREW-TYPE TERINLS 38 XS84 ux. Terminal Package (optional) SWIVEL LBEL HOLDER 5.5 Fig. 3. CentraLine LonWorks Bus I/O odules (example shows anual Overrides), incl. Terminal Socket, outside dimensions (in mm) anufactured for and on behalf of the Environmental & Energy Solutions Division of Honeywell Technologies Sàrl, Rolle, Z.. La Pièce 6, Switzerland by its uthorized Representative: CentraLine Honeywell GmbH Böblinger Strasse 7 70 Schönaich, Germany Phone +4 (0) Fax +4 (0) info@centraline.com Subject to change without notice EN0Z-080GE5 R036