PC POWER SUPPLY SUPERVISOR
|
|
- Isaac Gibbs
- 6 years ago
- Views:
Transcription
1 ` HY510N PC POWER SUPPLY SUPERVISOR Data Sheet REV September 21, 2004 The information in this document is subject to change without notice TEL: FAX: salesdep@hawyang.com.tw
2 GENERAL DESCRIPTION The HY510N provides protection circuits, power good output (), fault protection latch (), and a protection detector function () control. It can minimize external components of switching power supply systems in personal computer. The Over Voltage Detector (OVD) monitors 3.3V, 5V, 12V input voltage level. The Under Voltage Detector (UVD) monitors 3.3V, 5V input voltage level. When OVD or UVD detect the fault voltage level, the is latched HIGH and go low. The latch can be reset by goo HIGH. There is 2.4 ms delay time for turn off. When OVD and UVD detect the right voltage level, the power good output () will be issue. FEATURES The Over Voltage Detector (OVD) monitors 3.3V, 5V, 12V input voltage level. The Under Voltage Detector (UVD) monitors 3.3V, 5V input voltage level. Both of the power good output () and fault protection latch () are Open Drain Output. 75 ms time delay for UVD. 300 ms time delay for. 38 ms for input signal De bounce. 73 us for internal signal De glitches. 2.4 ms time delay for turn-off. ESD voltage up to 4000V as tested under MIL STD 883D, Method PIN ASSIGNMENT AND PACKAGE TYPE GND VCC 3 6 V5 4 5 V33 ORDERING INFORMATION PACKAGE 8 Pin Plastic DIP 8 Pin Plastic SOP HY510N N080WT HY510N S080WT Lead Free Pb HY510N N080WT Pb HY510N S080WT Pb The Top-Side Marking would be added a dot in the right side for lead-free package. PIN DESCRIPTION Pin No. Pin Name TYPE Description 1 I power good input pin 2 GND P Ground 3 O fault protection latch output pin(open drain output) 4 I protection detector function ON/OFF control input pin 5 V33 I 3.3V input pin 6 V5 I 5V input pin 7 VCC I Supply voltage / 12V input pin 8 O power good output pin(open drain output) Page 2
3 FUNCTION TABLE UV OV < 0.95V L no no L L < 0.95V L no yes H L < 0.95V L yes no L L 0.95 < < 1.2 L no no L L 0.95 < < 1.2 L no yes H L 0.95 < < 1.2 L yes no H L > 1.2 L no no L H > 1.2 L no yes H L > 1.2 L yes no H L x H x x H L x = don t care BLOCK DIAGRAM VCC EN0158A_WT7510 BLOCK DIAGRAM 150uA Power On Reset VCC Low Voltage POR LVRST Clock Generator PWR 3.6V PWR PWR 38ms debounce RST clr 2.4ms delay V UN PWR + - OV clr 75 ms delay V5 - UN + RST R - OV + 73us debounce S Q VCC + - OV RST VCC + - UN 73us debounce clr 300ms delay 1.2V V Page 3
4 RECOMMENDED OPERATING CONDITIONS Parameter Conditions Min. Typ. Max. Unit Supply voltage, VCC V Input voltage, V5, V33, 7 V Output voltage 15 V 7 V Operating temperature Output sink current 30 ma 10 ma Supply voltage rising time 1 ms ELECTRICAL CHARACTERISTICS, at Ta=25 C and V CC =5V. Over Voltage Detection Parameter Condition Min. Typ. Max. Unit Over voltage threshold V V V V Vcc / V V I LEAKAGE Leakage current () V() = 5V 5 ua V OL Low level output voltage () I sink 10mA 0.3 V I sink 30mA 0.7 and Parameter Condition Min. Typ. Max. Unit Under voltage threshold V V V V Input threshold voltage() V I LEAKAGE Leakage current() = 5V 5 ua V OL Low level output voltage() 0.4 V Parameter Condition Min. Typ. Max. Unit Input pull-up current = 0V 150 ua High-level input voltage 2.0 V Low-level input voltage 0.8 V TOTAL DEVICE Parameter Condition Min. Typ. Max. Unit Icc Supply current PDON _N= 5V 1 ma Vcc low voltage 3 V SWITCHING CHARACTERISTICS, Vcc=5V Parameter Condition Min. Typ. Max. Unit De-bounce time () ms t dleay1 Delay time ( to ) ms De-bounce time () ms t g De-glitch time us to delay time ms t delay3 Internal UVD delay time go low & ms every time > 0.95V Page 4
5 APPLICATION CIRCUIT 5V 5V uF 2 GND VCC 7 12V V5 V V 3.3V VSB 0.01uF Page 5
6 APPLICATION TIMMING 1.) (UNDER_VOLTAGE) Page 6
7 2.) V33, V5 (UNDER_VOLTAGE) V33 / V5 t delay3 =75mS t delay3 +t g V33 / V5 Page 7
8 3.) V33, V5, V12 (OVER_VOLTAGE) V33/V5/V12 t g V33/V5/V12 Page 8
9 MECHANICAL INFORMATION PLASTIC DUAL IN LINE PACKAGE NOTE 1 All linear dimensions are in inches millimeters. NOTE 2 This drawing is subject to change without notice. NOTE 3 Falls within JEDEC MS 001 Page 9
10 PLASTIC SMALL OUTLINE PACKAGE NOTE 1 All linear dimensions are in inches millimeters. NOTE 2 This drawing is subject to change without notice. NOTE 3 Falls within JEDEC MS 012 Page 10
FAN7680. PC Power Supply Outputs Monitoring IC. Features. Description. Typical Application. FPO OVP UVP PGO PSON
PC Power Supply Outputs Monitoring IC www.fairchildsemi.com Features PC Power Supply Output Monitor Circuitry Few External Components Over Voltage Protection for.v, V and V(Vcc) Outputs Under Voltage Protection
More informationFeatures VCC MIC1810 RESET RESET
Microprocessor Reset Circuit General Description The is an inexpensive microprocessor supervisory circuit that monitors power supplies in microprocessor based systems. The function of these devices is
More informationMIC1832. General Description. Features. Applications. Typical Application
3.3V Voltage Supervisor with Manual Reset, Watchdog Timer and Dual Reset Outputs General Description The is a low-current microprocessor supervisor for monitoring 3.3V and 3V systems. The device features
More informationFM1233A 3-Pin µc Supervisor Circuit
FM133A 3-Pin µc Supervisor Circuit General Description The FM133A is a supervisor circuit that monitors a microprocessor power supply or other system voltage and issues a reset pulse when a fault condition
More informationACE803ND 3-Pin Microprocessor Reset Circuits
Description ACE803ND The ACE803ND is a microprocessor (μp) supervisory circuit used to monitor the power supplies in μp and digital systems. It provides excellent circuit reliability and low cost by eliminating
More informationSILICON TOUCH TECHNOLOGY INC
Version : PRE.005 Issue Date : 2012/02/20 File Name Total Pages : 14 : SP-PS257-PRE.005.doc 4-Channel Secondary Monitoring IC with Fan Control 新竹市科學園區展業一路 9 號 7 樓之 1 SILICON TOUCH TECHNOLOGY INC. 9-7F-1,
More informationAIC A Dual USB High-Side Power Switch FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION CIRCUIT
1.0A Dual USB High-Side Power Switch FEATURES 2.7V to 6.5V Input Voltage Range 1.0A Dual Continuous Load Current 100mΩ High-Side P-MOSFET Switch 20Ω Open-Drain Over-Current Flag Output 80uA Quiescent Supply
More informationACE24AC128 Two-wire Serial EEPROM
Description The ACE24AC128 series are 131,072 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 16,384 words of 8 bits (one byte) each.
More informationFAN3989 USB/Charger Detection Device with Load Switch
FAN3989 USB/Charger Detection Device with Load Switch Features Charger/USB Detection Device with Load Switch Charger/USB Device Detection Flag Over/Under-Voltage Detection Flag Load Switch Output, Up to
More informationACE24AC64 Two-wire Serial EEPROM
Description The ACE24AC64 series are 65,536 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 8192 words of 8 bits (one byte) each. The
More informationDS1834/A/D Dual EconoReset with Pushbutton
Dual EconoReset with Pushbutton www.dalsemi.com FEATURES 5V power-on reset 3.3V power-on reset Internal power is drawn from higher of either the input or the 3.3V IN input Excellent for systems designed
More informationDescription. Features. Pin Configuration PI4IOE5V9539
16-bit I 2 C-bus and SMBus low power I/O port with interrupt and reset Features Operation power supply voltage from 2.3V to 5.5V 16-bit I 2 C-bus GPIO with interrupt and reset 5V tolerant I/Os Polarity
More informationReset Output. Active high Active low Active high Active low
Low Power Voltage Detector Features High accuracy: 2% (25 C) Low power consumption: 0.6μA @ 3V Vcc Detecting voltage range: 1.8 to 5V in 100mV increments Operating voltage range: 1.2V ~ 5.5V Operating
More informationFeatures MIC2779L IN OUT HTH GND. Cellular Telephone Battery Monitor
MIC2779 Voltage Monitor with Adjustable Hysteresis General Description The MIC2779 is a voltage monitor uniquely designed to detect two separate voltage thresholds combined with a delay generator and logic.
More informationACE24AC02A1 Two-wire Serial EEPROM
Description The ACE24AC02A1 is 2048 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 256 words of 8 bits (1 byte) each. The devices
More information74LVT244 74LVTH244 Low Voltage Octal Buffer/Line Driver with 3-STATE Outputs
Low Voltage Octal Buffer/Line Driver with 3-STATE Outputs General Description The LVT244 and LVTH244 are octal buffers and line drivers designed to be employed as memory address drivers, clock drivers
More informationACE24AC16B Two-wire Serial EEPROM
Description The ACE24AC16B is 16,384 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 2,048 words of 8 bits (1 byte) each. The devices
More informationLM3704/LM3705 Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output and Manual Reset
LM3704/LM3705 Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output and Manual Reset General Description The LM3704/LM3705 series of microprocessor supervisory circuits provide the
More informationup7535 Dual-Input Triple-Output Power Multiplexer in PSOP-8L for USB High Side Switch General Description Ordering Information Applications
Dual-Input Triple-Output Power Multiplexer in PSOP-8L for USB High Side Switch The up7535 is a current limited, dual-input triple-output power multiplexer acting as a high side switch for USB applications
More informationUM3221E/UM3222E/UM3232E
General Description UM3221E/UM3222E/UM3232E Fail-Safe, Single Supply RS-232 Transceivers UM3221E/UM3222E/UM3232E The UM3221E/UM3222E/UM3232E series are 3.3V powered RS-232 transceivers intended for portable
More informationUM Pin Microprocessor Reset Circuits UM803 SOT323/SOT23-3. General Description. Applications. Features
General Description UM803 3-Pin Microprocessor Reset Circuits UM803 SOT323/SOT23-3 The UM803 is a microprocessor (μp) supervisory circuit used to monitor the power supplies in μp and digital systems. It
More informationPI4IOE5V bit I 2 C-bus and SMBus low power I/O port with interrupt and reset
Features Operation power supply voltage from 2.3V to 5.5V 2-bit I 2 C-bus GPIO with interrupt and reset 5V tolerant I/Os Active Low interrupt output Active Low reset input Polarity inversion register Low
More informationTechnical Data Sheet Photolink- Fiber Optic Receiver
Technical Data Sheet Photolink- Fiber Optic Receiver Features 1. High PD sensitivity optimized for red light 2. Data : NRZ signal 3. Low power consumption for extended battery life 4. Built-in threshold
More informationPI4IOE5V bit I 2 C-bus and SMBus I/O port with reset. Description. Features. Pin Configuration
Features Operation power supply voltage from 2.3V to 5.5V 8-bit I 2 C-bus GPIO with interrupt and reset 5V tolerant I/Os Polarity inversion register Active LOW Reset Pin Low current consumption 0Hz to
More informationDESCRIPTION FEATURES APPLICATIONS. Digital Echo/Surround Processor IC PT2396
DESCRIPTION PT2396 is a digital echo/surround processor IC utilizing CMOS Technology. Analog Signal inputted to PT2396 is converted to digital signal by A-D converter and then stored into the internal
More informationDS1834/A/D Dual EconoReset with Pushbutton
DS1834/A/D Dual EconoReset with Pushbutton www.dalsemi.com FEATURES 5V power-on reset 3.3V power-on reset Internal power is drawn from higher of either the 5V IN input or the 3.3V IN input Excellent for
More informationVGA Port Companion Circuit
GA Port Companion Circuit Features Single chip solution for the GA port interface Includes ESD protection, level shifting, and RGB termination Seven channels of ESD protection for all GA port connector
More informationRemote 16-bit I/O expander for Fm+ I 2 C-bus with interrupt and reset. Description
Remote 16-bit I/O expander for Fm+ I 2 C-bus with interrupt and reset Features Operation power supply voltage from 2.3V to 5.5V 16-bit remote I/O pins that default to inputs at powerup 1 MHz I 2 C-bus
More informationACE24AC02A3C Two-wire Serial EEPROM
Description The ACE24AC02A3C is 2048 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 256 words of 8 bits (1 byte) each. The devices
More information±15kV ESD-Protected, Single/Dual/Octal, CMOS Switch Debouncers
19-477; Rev 1; 1/99 ±15k ESD-Protected, Single/Dual/Octal, General Description The are single, dual, and octal switch debouncers that provide clean interfacing of mechanical switches to digital systems.
More information74F00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description This device contains four independent gates, each of which performs the logic NAND function. Ordering Code: December 1994 Revised September 2000 Order Number
More informationPT7M Ultra Low Voltage Detectors
Features Factory-Set Reset Threshold Voltages for Nominal Supplies from 1.2V to 1.8V Low power consumption : Typ 7.5μA Five different timeout periods available: 70μs(voltage detector), 1.5ms, 30ms, 210ms
More informationZA85183/A. Application. Marking Information. Ordering information ZA8518. Revision 0.3 Page 1/7
High Performance LED Flicker Attenuator Features Flicker Attenuator Maximum output current 300mA, 600mA, Maximum output LED voltage up to 100V. Automatic regulated loading current Internal soft start Built-in
More informationTTP226. Preliminary 8 KEYS TOUCH PAD DETECTOR IC GENERAL DESCRIPTION
8 KEYS TOUCH PAD DETECTOR IC GENERAL DESCRIPTION The TTP222 is a touch pad detector IC which offers 8 touch keys. The touching detection IC is designed for replacing traditional direct button key with
More informationV PP IN V CC3 IN V CC5 IN EN0 EN1 MIC2561 V CC5_EN V CC3_EN
MIC2561 PCMCIA Card Socket and V PP Switching Matrix Final Information General Description The MIC2561 & V PP Matrix controls PCMCIA (Personal Computer Memory Card International Association) memory card
More informationSP6331, SP6333, & SP6335 Quad µpower Supervisory Circuit
SP6331, SP6333, & SP6335 Quad µpower Supervisory Circuit FEATURES Low operating voltage of 1.6V Low operating current of 20µA typical Monitors up to four supplies simultaneously Adjustable inputs monitor
More informationICE27C Megabit(128KX8) OTP EPROM
1- Megabit(128KX8) OTP EPROM Description The is a low-power, high-performance 1M(1,048,576) bit one-time programmable read only memory (OTP EPROM) organized as 128K by 8 bits. It is single 5V power supply
More informationDS1814/DS1819 5V and 3.3V MicroMonitor
5V and 3.3V MicroMonitor www.maxim-ic.com FEATURES Halts and restarts an out-of-control microprocessor Holds microprocessor in check during power transients Automatically restarts microprocessor after
More informationGT24C32A 2-WIRE. 32K Bits. Serial EEPROM
GT24C32A 2-WIRE 32K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any
More informationDS1830/A Reset Sequence Pushbutton
DS1830/A DS183 DS1830/A Reset Sequence Pushbutton www.maxim-ic.com FEATURES 5V (DS1830) or 3.3V (DS1830A) power-on reset Excellent for systems that need power-on resets in a consistent sequence Asserts
More informationMIC826. General Description. Features. Applications. Typical Application
Voltage Supervisor with Watchdog Timer, Manual Reset, and Dual Outputs In 1.6mm x 1.6mm TDFN General Description The is a low-current, ultra-small, voltage supervisor with manual reset input, watchdog
More informationDS1232 MicroMonitor Chip
DS1232 MicroMonitor Chip www.maxim-ic.com FEATURES Halts and restarts an out-of-control microprocessor Holds microprocessor in check during power transients Automatically restarts microprocessor after
More informationDS1810 5V EconoReset with Push-Pull Output
5V EconoReset with Push-Pull Output www.maxim-ic.com FEATURES Automatically restarts a microprocessor after power failure Maintains reset for 150 ms after V CC returns to an in-tolerance condition Reduces
More informationMP6219 5V, 1A 2A Programmable Current Limit Power Distribution Switch
The Future of Analog IC Technology MP6219 5V, 1A 2A Programmable Current Limit Power Distribution Switch DESCRIPTION The MP6219 is a protection device designed to protect circuitry on the output from transients
More informationFP6600. USB Dedicated Charging Port Controller with QC 2.0 Fast Charging Function. Features. Description. Applications.
USB Dedicated Charging Port Controller with QC 2.0 Fast Charging Function Description The is a fast charge protocol controller and follows Quick Charge 2.0 specification for smart power bank application.
More informationMP5007 5V, 1A- 5A Programmable Current Limit Switch
The Future of Analog IC Technology DESCRIPTION The MP5007 is a protection device designed to protect circuitry on the output (source) from transients on input (V CC ). It also protects V CC from undesired
More informationGT24C WIRE. 1024K Bits. Serial EEPROM
GT24C1024 2-WIRE 1024K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at
More informationMIC2546/2547. Features. General Description. Applications. Typical Application. Dual Programable Current Limit Switch
Dual Programable Current Limit Switch General Description The MIC2546 and MIC2547 are integrated high-side dual power switches optimized for low loss dc power switching and other power management applications,
More informationMP V, 1A Dual Input Linear Battery Charger With Timer
MP268 28V, 1A Dual Input Linear Battery Charger With Timer The Future of Analog IC Technology DESCRIPTION The MP268 is a dualinput, linear, highperformance lowcost single cell LiIon or LiPolymer battery
More informationAIC1526. Dual USB High-Side Power Switch FEATURES DESCRIPTION APPLICATIONS
Dual USB High-Side Power Switch FEATURES 110mΩ (5V Input) High-Side MOSFET Switch. 500mA Continuous Load Current per Channel. 110µA Typical On-State Supply Current. 1µA Typical Off-State Supply Current.
More informationDS3668 Quad Fault Protected Peripheral Driver
Quad Fault Protected Peripheral Driver General Description The DS3668 quad peripheral driver is designed for those applications where low operating power, high breakdown voltage, high output current and
More informationXRA BIT I2C/SMBUS GPIO EXPANDER WITH INTEGRATED LEVEL SHIFTERS
SEPTEMBER 2011 REV. 1.0.0 GENERAL DESCRIPTION The XRA1207 is a 16-bit GPIO expander with an I 2 C/ SMBus interface. After power-up, the XRA1207 has internal 100K ohm pull-up resistors on each pin that
More informationOPTICAL MOUSE SENSOR
OPTICAL MOUSE SENSOR NST TECHNOLOGIES Series Data sheet USB INTERFACE Version 1.52 1 1. Description is a low-cost CMOS optical sensor SOC for USB optical computer mouse. It provides an all-in-one solution
More informationGT24C256 2-WIRE. 256K Bits. Serial EEPROM
GT24C256 2-WIRE 256K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any
More informationFigure 1: TSSOP-24 ( Top View ) Figure 2: TQFN 4x4-24 ( Top View )
16-bit I2C-bus and SMBus I/O port with interrupt Features Operation power supply voltage from 2.3V to 5.5V 16-bit I/O pins which can be programmed as Input or Output 5V tolerant I/Os Polarity inversion
More informationXRD87L85 Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter
Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter April 2002-1 FEATURES 8-Bit Resolution Up to 10 MHz Sampling Rate Internal S/H Function Single Supply: 3.3V VIN DC Range: 0V to V DD VREF DC
More informationMAX705-MAX813L Low-Cost, µp Supervisory Circuit
General Description The MAX705-MAX708/MAX813L microprocessor (µp) supervisory circuits reduce the complexity and number of components required to monitor power-supply and battery functions in µp systems.
More information8K X 8 BIT LOW POWER CMOS SRAM
FEATURES 8192 x 8 bit static CMOS RAM 70 ns Access Times Common data inputs and outputs Three-state outputs Typ. operating supply current o 70 ns: 10 ma Standby current: o < 2 μa at Ta 70 C Data retention
More informationXRA1201/1201P 16-BIT I2C/SMBUS GPIO EXPANDER
SEPTEMBER 2011 REV. 1.0.0 GENERAL DESCRIPTION The XRA1201/1201P is a 16-bit GPIO expander with an I 2 C/SMBus interface. After power-up, the XRA1201 has internal 100K ohm pull-up resistors on each pin
More informationMIC2544A/2548A. General Description. Features. Applications. Typical Application. Programmable Current Limit High-Side Switch
Programmable Current Limit High-Side Switch General Description The MIC2544A and MIC2548A are integrated, high-side power switches optimized for low loss DC power switching and other power management applications,
More informationUSB/Charger and Over-Voltage Detection Device
FAN3988 USB/Charger and Over-Voltage ion Device Features Charger/USB ion Device Charger/USB Device ion Flag Over-/Under-Voltage ion Flag V BUS Supply: 2.7 V to 20 V C ON of 1.5 pf 6-Lead MicroPak MLP Package
More informationLow Voltage 1.65 V to 3.6 V, Bidirectional Logic Level Translation, Bypass Switch ADG3233
Data Sheet Low Voltage. V to. V, Bidirectional Logic Level Translation, Bypass Switch ADG FEATURES Operates from. V to. V supply rails Bidirectional level translation, unidirectional signal path -lead
More information73S8014BN Smart Card Interface
19-5669; Rev 2; 12/11 73S8014BN Smart Card Interface DESCRIPTION The 73S8014BN is a single smart card (ICC) interface circuit designed to provide full electrical compliance with ISO 7816-3, EMV 4.2, and
More informationPI4IOE5V bit general purpose outputs for 1MHz I 2 C bus
Features Operation power supply voltage from 2.3V to 5.5V 4-bit I 2 C-bus GPO 1 MHz I 2 C-bus interface with 30 ma SDA sink capability for 4000pF Latched outputs with 25mA capability for directly driving
More information0534S PESDR0534S2. 4-Line Low Capacitance TVS Diode Array. Mechanical Characteristics. Description. Applications. Features. Marking Information
4-Line Low Capacitance TVS Diode Array Description The is a low capacitance TVS arrays, utilizing leading monolithic silicon technology to provide fast response time and low ESD clamping voltage, making
More informationCraft Port Tiny RS-232 Transceiver for Portable Applications ADM101E. Data Sheet FUNCTIONAL BLOCK DIAGRAM
Data Sheet FEATURES 460 kbit/s Transmission Rate Single 5 V Power Supply Compatible with RS-232 Input/Output Levels 0.1 μf Charge Pump Capacitors One Driver and One Receiver On-Board DC-DC Converter ±4.2
More informationXRA1202/1202P 8-BIT I2C/SMBUS GPIO EXPANDER WITH RESET
8-BIT I2C/SMBUS GPIO EXPANDER WITH RESET APRIL 2013 REV. 1.0.1 GENERAL DESCRIPTION The XRA1202/1202P is an 8-bit GPIO expander with an I 2 C/SMBus interface. After power-up, the XRA1202 has internal 100K
More informationDS1845 Dual NV Potentiometer and Memory
www.maxim-ic.com FEATURES Two linear taper potentiometers -010 one 10k, 100 position & one 10k, 256 position -050 one 10k, 100 position & one 50k, 256 postition -100 one 10k, 100 position & one 100k, 256
More informationTurning Ideas Into Reality ABCircuits POB 123 New Hill NC (919) C922-SO IC
ABCircuits www.abcircuits.com POB 123 New Hill 27562 (919) 290-7104 74C922-SO IC Keyboard / Keypad Encoder for up to 16 switches MM74C922 Replacement IC General Description The 74C922-SO is designed as
More informationISSI Preliminary Information January 2006
2K-BIT/4K-BIT SPI SERIAL ELECTRICALLY ERASABLE PROM January 2006 FEATURES Serial Peripheral Interface (SPI) Compatible Supports SPI Modes 0 (0,0) and 3 (1,1) Low-voltage Operation Vcc = 1.8V to 5.5V Low
More informationOPTICAL MOUSE SENSOR
OPTICAL MOUSE SENSOR NST TECHNOLOGIES Series Data sheet USB INTERFACE Version 1.50 1. Description is a low-cost CMOS optical sensor SOC for USB optical computer mouse. It provides an all-in-one solution
More informationSTEF12E. Electronic fuse for 12 V line. Datasheet. Features. Applications. Description
Datasheet Electronic fuse for 12 V line Features DFN10 (3x3 mm) Continuous current typ. 3.6 A N-channel on-resistance typ. 45 mω Enable/fault functions Output clamp voltage typ. 15 V Undervoltage lockout
More informationAPX803/D 3-PIN MICROPROCESSOR RESET CIRCUIT. Description. Pin Assignments. Features. Applications APX803. ( Top View ) SOT23. ( Top View ) SOT23R GND
/D Description Pin Assignments The /D is used for microprocessor (µp) supervisory circuits to monitor the power supplies in µp and digital ( Top View ) systems. They provide excellent circuit reliability
More information74VHC132 Quad 2-Input NAND Schmitt Trigger
74VHC132 Quad 2-Input NAND Schmitt Trigger General Description The VHC132 is an advanced high speed CMOS 2-input NAND Schmitt Trigger Gate fabricated with silicon gate CMOS technology. It achieves the
More informationSTM706T/S/R, STM706P, STM708T/S/R
STM706T/S/R, STM706P, STM708T/S/R 3 V supervisor Features Datasheet - production data Precision monitor T: 3.00 V V RST 3.15 V S: 2.88 V V RST 3.00 V R: STM706P: 2.59 V V RST 2.70 V RST and RST outputs
More informationWS3210 WS3210. Over-Voltage Protection Load Switch. Descriptions. Features. Order information. Applications.
Over-Voltage Protection Load Switch http://www.sh-willsemi.com WS3210 Descriptions The WS3210 features a low internal High Voltage Switch and an input range of absolute maximum 30V. An internal input clamp
More informationLow cost, 3 Step Dimming Control, Linear AC LED Driver. Features. Applications. Fig. 1 Typical application with 3 Step dimming
Low cost, 3 Step Dimming Control, Linear AC LED Driver General Description The is a non-isolated linear LED driver for general purpose LED lighting applications. It is capable of driving LEDs in multiple
More informationLOW EMI PWM INTELLIGENT POWER HIGH SIDE SWITCH
Automotive grade Automotive IPS High side AUIPS72211R LOW EMI PWM INTELLIGENT POWER HIGH SIDE SWITCH Features Integrated bootstrap for 100kHz switching Optimized EMI switching Charge pump for DC operation
More informationTMR1202. General Description. TMR Bipolar Switch. Features and Benefits. Applications
General Description TMR1202 TMR Bipolar Switch The TMR1202 is a digital bipolar magnetic switch that integrates TMR and CMOS technology in order to provide a magnetically triggered digital switch with
More informationFXL6408 Fully Configurable 8-Bit I 2 C-Controlled GPIO Expander
October 2012 FXL6408 Fully Configurable 8-Bit I 2 C-Controlled GPIO Expander Features 4X Expansion of Connected Processor I/O Ports Fully Integrated I 2 C Slave 8 Independently Configurable I/O Ports Low-Power
More information1-Megabit (128K x 8) 5-volt Only Flash Memory AT29C010A. Features. Description. Pin Configurations
Features Fast Read Access Time - 70 ns 5-Volt Only Reprogramming Sector Program Operation Single Cycle Reprogram (Erase and Program) 1024 Sectors (128 bytes/sector) Internal Address and Data Latches for
More informationOTP MATRIX 3-D MEMORY - 32PIN TSOP 16MB, 32MB, 64MB DATA SHEET DOCUMENT NUMBER: DS004 REVISION: 1.11 REVISION DATE:
16MB, 32MB, 64MB DATA SHEET REVISION: 111 REVISION DATE: 06-24-05 REV 111 06/24/05 NOTICES: Copyright 2002, 2004, 2005 Matrix Semiconductor, Inc All rights reserved If you have received this document from
More informationLM75 Digital Temperature Sensor and Thermal WATCHDOG with Two-Wire Interface
LM75 Digital Temperature Sensor and Thermal WATCHDOG with Two-Wire Interface General Description The LM75 is a temperature sensor, Delta-Sigma analog-to-digital converter, and digital over-temperature
More informationLow Voltage, 10-Bit Digital Temperature Sensor in 8-Lead MSOP AD7314
a FEATURES 10-Bit Temperature-to-Digital Converter 35 C to +85 C Operating Temperature Range 2 C Accuracy SPI and DSP Compatible Serial Interface Shutdown Mode Space-Saving MSOP Package APPLICATIONS Hard
More informationCAT28C17A 16K-Bit CMOS PARALLEL EEPROM
16K-Bit CMOS PARALLEL EEPROM HALOGENFREE LEAD TM FREE FEATURES Fast Read Access Times: 200 ns Low Power CMOS Dissipation: Active: 25 ma Max. Standby: 100 µa Max. Simple Write Operation: On-Chip Address
More informationLow Voltage 1.65 V to 3.6 V, Bidirectional Logic Level Translation, Bypass Switch ADG3233
Low Voltage. V to. V, Bidirectional Logic Level Translation, Bypass Switch FEATURES Operates from. V to. V supply rails Bidirectional level translation, unidirectional signal path -lead SOT- and MSOP packages
More informationFeatures. Applications. n Embedded Controllers and Processors n Intelligent Instruments n Automotive Systems n Critical µp Power Monitoring
Microprocessor Supervisory Circuits with Separate Watchdog Timer Output, Power Fail Input and Manual Reset General Description The LM3712/LM3713 series of microprocessor supervisory circuits provide the
More informationOvervoltage-Protection Controllers with a Low RON Internal FET MAX4970/MAX4971/MAX4972
19-4139; Rev 1; 8/08 Overvoltage-Protection Controllers General Description The family of overvoltage protection devices features a low 40mΩ (typ) R ON internal FET and protect low-voltage systems against
More informationGT24C64 2-WIRE. 64K Bits. Serial EEPROM
GT24C64 2-WIRE 64K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any
More information4-Megabit 2.7-volt Only Serial DataFlash AT45DB041. Features. Description. Pin Configurations
Features Single 2.7V - 3.6V Supply Serial Interface Architecture Page Program Operation Single Cycle Reprogram (Erase and Program) 2048 Pages (264 Bytes/Page) Main Memory Two 264-Byte SRAM Data Buffers
More informationHigh- Performance Flash PLD ATF16V8B. Features. Block Diagram. Pin Configurations
Features Industry Standard Architecture Emulates Many 20-Pin PALs Low Cost Easy-to-Use Software Tools High-Speed Electrically Erasable Programmable Logic Devices 7.5 ns Maximum Pin-to-Pin Delay Several
More informationZLED7002. Toggle (Side-Step) Dual-Channel LED Driver. Datasheet. Features. Brief Description. Benefits. Available Support. Physical Characteristics
Toggle (Side-Step) Dual-Channel LED Driver ZLED7002 Datasheet Brief Description The ZLED7002 toggle (side-step) dual-channel LED driver is one of our ZLED family of LED control ICs. It operates in the
More informationBattery-Voltage. 16K (2K x 8) Parallel EEPROMs AT28BV16. Features. Description. Pin Configurations
Features 2.7 to 3.6V Supply Full Read and Write Operation Low Power Dissipation 8 ma Active Current 50 µa CMOS Standby Current Read Access Time - 250 ns Byte Write - 3 ms Direct Microprocessor Control
More informationRayStar Microelectronics Technology Inc.
Features Precision supply-voltage monitor - 4.63V (RS809L) - 4.38V (RS809M) - 4.00V (RS809J) - 3.08V (RS809T) - 2.93V (RS809S) - 2.63V (RS809R) - 2.32V (RS809Z) 140ms(min) reset pulse width Push-Pull /
More informationAS Channels Capacitive Touch Sensor IC From Santa Clara, United States of America
ASI Competitor Equivalent A Competitor Equivalent B Volts Leading Performance: ESD HBM >8k Volts (Directly Applied to All IC Pins) Operating Temperature up to >+95 0 C Features Overview Analog and Digital
More informationUNISONIC TECHNOLOGIES CO.,LTD. UL318 Preliminary LINEAR INTEGRATED CIRCUIT
UNISONIC TECHNOLOGIES CO.,LTD. UL318 Preliminary LINEAR INTEGRATED CIRCUIT SERIAL-INTERFACED 10-DIGIT LED CONTROLLER IC WITH KEYSCAN DESCRIPTION The UL318 is a compact LED controller and driver that interface
More information2-wire Serial EEPROM AT24C512. Preliminary. 2-Wire Serial EEPROM 512K (65,536 x 8) Features. Description. Pin Configurations.
Features Low-voltage and Standard-voltage Operation 5.0 (V CC = 4.5V to 5.5V) 2.7 (V CC = 2.7V to 5.5V) 1.8 (V CC = 1.8V to 3.6V) Internally Organized 65,536 x 8 2-wire Serial Interface Schmitt Triggers,
More informationFeatures. Applications. n Embedded Controllers and Processors n Intelligent Instruments n Automotive Systems n Critical µp Power Monitoring
LM3710/LM3711 Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output, Manual Reset and Watchdog Timer General Description The LM3710/LM3711 series of microprocessor supervisory circuits
More informationHigh Voltage Input Protection Device ADM1270
High Voltage Input Protection Device FEATURES FUNCTIONAL BLOCK DIAGRAM Controls supply voltages from 4 V to 60 V Gate drive for low voltage drop reverse supply protection Gate drive for P-channel FETs
More informationUNISONIC TECHNOLOGIES CO., LTD
UNINIC TECHNOLOGIES CO., LTD 20-BIT SERIAL TO PARALLEL CONVERTER DESCRIPTION The UTC LS3718 is a 20-bit serial to parallel converter utilizing CMOS Technology. It is incorporates control circuit, shift
More information