BUS RACK & BOARD SYSTEM

Transcription

1 BUS RACK & BOARD SYSTEM

2 SRC commits Customer Oriented Production and realizes Zero defect. BUS RACK & BOARD family of SRC confirms to VME BUS CompactPCI bus standard and offers units system, backboard products, extenders and rack mount system for euro board.many customers including board vendors use our product because we provide variety of product family with reasonable cost to meet various market's needs.we will continue to do our best to provide best products which can help your business as the professional company in electronics packaging area. Please take a chance and consider to consider the adaptation of our products on your system. Our products are specialized in: Highest Quality but low cost products Providing from parts to whole system Product configuration with the concept of quicker adaptation of customer's requirements Company profile Name : SRC CORPORATION HDQ : Maruki Building -3-7 Nishi-Gotanda Shinagawa-ku Tokyo, Japan -003 Kansai branch : -20- Higashi-Nakajima Higashi-Yodogawa-ku Osaka, Japan Foundation : Feb987 Capital : 30M yen Product portfolio Standard bus backboard Rack & parts confirming euro board specification Universal board confirming euro board specification Universal backboard Extender boards Plug-in Power units Design & manufacturing of electric packaging architecture

3 CONTENTS CompactPCI TMproducts of SRC Single height system rack Double height system rack (rear I/O corresponding type) Sub module rack Module units CPCI development support units(6u) CPCI development support units (6U rear panel I/O corresponding type) CPCI backboard(3u) CPCI backboard(6u) CPCI backboard (6U bridge corresponding type) CPCI backboard (R3.0 corresponded) Computer telephony backboard PXI bus backboard Bus bridge module CPCI single height extender board CPCI double height extender board Attention

4 Single height system rack Standard system configuration Item/Model SCR-206SESD slots Power +V 30A, +3.3V 0A, +2V.2A configuration 2V 0.9A Cooling method 3 DC FANs Others Noise filter, Switch, Fuse, FG terminal, AC code included Backboard is optional.. All except module board is included. 2. Backboard is optional. 3. Plug-in Power supply. (SCP-0930S is included & occupied 9 slots). IEEE0.0 confirmed & meets EMC/ESD specification.. Rack mountable with optional side frame(ssf-77c). Order code SCR-206SESD (W x H x D) 30.7 x 77.0 x mm Applicable board size 3U(00.0 x 60 mm) 30.7 Rack assembly +V power supply +2V power supply -2V power supply Back board (optional) V power supply AC switch AC inlet Side frame(optional) DC FAN Back view FG terminal Fuse folder Terminal block for relaying 2

5 Double height system rack (Rear I/O corresponding type) Standard system configuration Item/Model SCR-206WRIO slots Power +V 30A, +3.3V 0A, +2V.2A configuration 2V 0.9A Cooling method 3 DC FANs Others Noise filter, Switch, Fuse, FG terminal, AC code included Order code (W x H x D) SCR-206WRIO 30.7 x 30. x mm Applicable board size Front: 6U(233.3 x 60 mm) Rear: 6U(233.3 x 80mm) Backboard is optional.. POWER configuration: +V 30A, +3.3V 0A, +2V.2A, 2V 0.9A 2. Plug-in Power supply (SCP-030W is included) 3. IEEE0.0 and IEEE0. confirmed & meets EMC/ESD specification.. Rear I/O module can be installed at backside.. Cooling units includes 3 DC FANS. 6. Rack mout side frame(ssf-30c) is included. 7. Backboard is confirmed to t=3.2mm. 8. Backboard is optional Back view P P P3 Rack assembly FG terminal Fuse folder AC inlet +3.3V power supply +2V power supply Side frame Back board (optional) P P 2P3 P2 2P 2P 3P3 2P P 2P 76 3P 3P P3 3P2 3P P P P3 P2 76 P 76 P Model SPB-08CWR P 6P3 P2 P 76 6P CompactPCI with Hot Swap 6P 7P3 6P2 6P 76 7P 7P 8P3 7P2 7P 76 8P 8P 8P3 8P2 8P V power supply +V power supply switch 0 DC FAN 3

6 7P 6P P P 3P 7P 6P P P 3P 7P3 6P3 P3 P3 3P3 7P3 P3 7P P TM Example of disk unit mounting. Sub module rack Standard system configuration Item/Model SSM-2030CW SSM-2060CW SSM-20ATCW +V 30A +V 60A +V 30A Power +3.3V 30A +3.3V 60A +3.3V A configuration +2V 8.A +2V 8.A +2V 2A 2V.7A 2V.7A 2V 0.8A Cooling method Others 2 DC FANs Noise filter, Switch, Fuse, FG terminal, AC code included * Total usage of +V and +3.3V should be within 0W on SSM-20ATCW power configuration. Backboard is optional.. All functionality except module board is included. 2. IEEE0.0 confirmed & meets EMC/ESD specification 3. Rear I/O module can be installed at backside. (IEEE0. corresponded). Power unit can be used at AC00-26V, 0/60HZ.. Easy mounting of disk units and others. 6. Rack mountable with optional Side frame(ssf-3c). Order code (W x H x D) SSM-2030CW SSM-2060CW SSM-20ATCW 30.7 x 3.0 x 00.0 mm Applicable board size Front: 6U(233.3 x 60 mm) Rear: 6U(233.3 x 80mm) 30.7 Back view Backboard (optional) Side frame (optinal) 2P 2P 2P3 2P2 2P 3P3 3P P3 P 6P3 6P 8P 8P3 8P 8P3 8P COMPACT disc AC inlet AIR FLOW FG terminal Fuse folder AIR FLOW AC switch DC 20 square FAN

7 Module unit Standard system configuration Item/Model SMU-6CESD slots Backboard CompactPCI backboard(3u R2.) Power +V 30A, +3.3V 0A, +2V 3.6A configuration 2V.3A Cooling method 2 DC FANs Others Noise filter, Switch, Fuse, FG terminal, AC code included. All functionality except module board is included. 2. Double height modules can be packaged horizontally. (CPU module with 2 slots width can be packaged.) 3. Rack mountable with optional Side frame(ssf-32m).. Debugging on CPU module is possible by removing top cover.. System slot is assigned at top in standard configuration. 6. Easy mounting of disk units and others.(optional feature). Order code SMU-6CESD (W x H x D) 32.0 x 32. x 30.0 mm Applicable board size 6U(233.3 x 60 mm) DC FAN DC FAN -2V power supply AC switch Fuse folder Blank cover Backboard (SPB-0CR) +V power supply V power supply Back view +2V power supply 32 Disk bracket is optional LED lamp Caution label AC inlet 0 32.

8 TM Example of disk unit mounting. CPCI development support units (6U) Standard system configuration Item/Model SDR-0WATX SDR-06WATX SDR-08WATX slots 6 slots 8 slots Backboard CompactPCI backboard(3u R2.) Power +V 30A, +3.3V A, +2V 2A configuration 2V 0.8A Cooling method 2 DC FANs Others 2 sets of disk mounting bracket, AC code included. Order code (W x H x D) SDR-0WATX SDR-06WATX SDR-08WATX SDR- WATX x x mm 37. x x mm 38. x x mm Applicable board size 6U(233.3 x 60mm). Ultra low priced CPCI rack system for debugging. 2. High performance rack mount system with all units confirmed to standards.(backboard PICMG2.0 R2., ATX power supply ATX2.0) 3. ATX units can be used as embedded type.. Various drive units can be mounted easily.(3. / drive units max 3 ). System slot is assigned at the right in standard configuration. 6. 3U board can be packaged easily. 7. Cooling FAN can be equipped(optional) Disk bracket (7.) W CPCI backboard (SPB-0CR) COMPACT disc ATX power supply (This figure shows SDR-0WATX.) 6

9 TM This photo shows the example with cooling FAN equipped. CPCI development support units (6U) (Rear panel I/O corresponding type) Standard system configuration Item/Model SDR-0MATXW SDR-06MATXW SDR-08MATXW slots 6 slots 8 slots Backboard CompactPCI backboard(6u R2.) Item/Model SDR-0MATXT SDR-06MATXT SDR-08MATXT slots 6 slots 8 slots Backboard Computer telephony backboard Power configuration +V 30A,+3.3V A,+2V 2A, 2V 0.8A Others 2 sets of disk mounting bracket, AC code included.. Can debug with rear I/O installed. 2. All units confirm to standards (Backboard PICMG2.0 R2., ATX power supply ATX2.0) 3. Various drive units can be mounted easily.. System slot is assigned at the right in standard configuration.. Cooling FAN can be equipped(optional). Order code (W x H x D) SDR-0MATXW x 27.7 x 29. mm SDR-06MATXW x 27.7 x 29. mm SDR-08MATXW x 27.7 x 29. mm SDR-0MATXT x 27.7 x 29. mm SDR-06MATXT x 27.7 x 29. mm SDR-08MATXT x 27.7 x 29. mm Applicable board size Front: 6U(233.3 x 60 mm) Rear: 6U(233.3 x 80mm) SDR- WATX W: CompactPCI backboard T: Computer telephony backboard AIR FLOW 29. Disk bracket CPCI backboard (SPB-08CTR) Model SPB-08CTR 8P 7P 6P P P 3P 2P P 8P 7P 6P P P 3P 2P P ATX power supply P3 P2 P 2P3 2P2 2P P3 P2 P3 P2 3P3 3P2 3P P P 6P3 6P2 6P 7P3 7P2 7P 8P3 8P2 8P CompactPCI Computer Telephony (H.0) with Hot Swap (This figure shows SDR-08MATXT.) 7

10 CPCI backboard (3U) (R2. corresponding product) Specification. Board material : Epoxy glass(fr-, 3.2t, 0 layers) 2. Connector : IEC076(2mm hard metrics) 3. Power providing method : Bolting to terminal (8A per terminal) +V, +3.3V, +2V, -2V, GND. Check terminal : PRST, DEG, FAL, +V, GND. Others : M66EN applicable by cutting pattern Order code L N K System slot SPB-0C slots SPB-02CR slots SPB-0CR slots System slot SPB-06CR slots on the right SPB-08CR slots SPB-0CL slots System slot SPB-06CL slots on the left SPB-08CL slots SDR- WATX R: System slot on the right L: System slot on the left * We can accept special order on this product. We also build backboard with different size per request.. PICMG2.0R2. confirmed. 2. Impedance of signal lines are adjusted to 6 0% 3. 2 variation of System slot assignment is available(right or left).. 8 slots type equips long-type connector at the far end from system-slot and accepts off-board terminator(stb-6c).. Contact sales representative if you want to use with Bus module bridge. Power supply terminal 9. L x N=K 3.2 GA() GA(3) GA() GA(3) +3.3V Z 7-P2 2-P Z V(I/O) +V 0 +V Bus bar GND GND +2V -2V 7-P 2-P SYSTEM Shrouds 2mm hard metric connector (P/P2) (This figure shows backboard with system slot assigned on the right.) 8

11 CPCI backboard (6U) (R2. corresponding product) Specification. Board material : Epoxy glass(fr-, 3.2t, 0 layers) 2. Connector : IEC076(2mm hard metrics) 3. Power providing method: Bolting to terminal (8A per terminal) +V, +3.3V, +2V, -2V, GND. Check terminal : PRST, DEG, FAL, +V, GND. Others: M66EN applicable by cutting pattern Order code L N K System slot SPB-03CWR slots SPB-0CWR slots System slot SPB-06CWR slots on the right SPB-08CWR slots SPB-0CWL slots System slot SPB-06CWL slots SPB-08CWL slots on the left SPB- CW R: System slot on the right L: System slot on the left * We can accept special order on this product. We also build backboard with different size per request.. PICMG2.0R2. confirmed. 2. Hot-swap confirmed(picmg2.r.0) 3. Impedance of signal lines are adjusted to 6 0%. 2 variation of System slot assignment is available(right or left).. 8 slots type equips long-type connector at the far end from system-slot and accepts off-board terminator(stb-6c). 6. P3-P-P can be used to attach user I/O and rear I/O module. 7. Additional power supply terminal can be provided per optional request.(using fasten terminal) 8. VIO power switching bus bar is provided standard(+v at factory setting) 9. Type AB shrouds can be equipped optionally. SPB-08CWR front side L x N=K 3.2 SPB-08CWR rear side Power supply terminal P shrouds Bus bar P shrouds mm hard metric connector (P-P) ATX specified power connector P3 shrouds P2 shrouds P shrouds (This figure shows systems slot on the right.) 9

12 CPCI backboard (6U) (Bridge corresponding type) Specification. Board material: Epoxy glass(fr-, 3.2t, 0 layers) 2. Connector: IEC076(2mm hard metrics) 3. Power providing method: Bolting to terminal (8A per terminal) +V, +3.3V, +2V, -2V, GND. Check terminal: PRST, DEG, FAL, GND, IPMB-SCL PMB-SDA, IPMB-PWR. No peripheral slot is consumed for bridging. 2. Board address of interrupt signal can be set to any value. 3. Hot-swap corresponding(r2.0). Applicable to M66EN with register(33mhz at factory setting). Slot can be expand freely with combination. Order code SPB-02CWER SPB-0CWER SPB-06CWER SPB-07CWER SPB- CWER 2 slots slots 6 slots 7 slots Board size 39.3 x 262.0mm 79.9 x 262.0mm 20.9 x 262.0mm 0.9 x 262.0mm System slot System slot on the right SPB-07CWER front side SPB-07CWER rear side Power supply terminal x N=K 3.2 P shrouds P shrouds P3 shrouds Reinforce bar P2 shrouds P shrouds 2mm hard metric connector (P- P) 0

13 CPCI backboard (R3.0 corresponding product) Specification. Board material: Epoxy glass(fr-, 3.2t, 0 layers) 2. Connector: IEC076(2mm hard metrics) 3. Power providing method: Bolting to terminal ATX power connector. Check terminal: PRST, DEG, FAL. Others: M66ENA switching Order code SPB-0CWR3 L N K System slot slots System slot on the right * We can accept special order on this product. We also build backboard with different size per request.. PICMG2.0 R3.0, PICMG2. R.0(Hot swap) and PICMG2.0 R.0(keying) certified. 2. Impedance of signal lines are adjusted to 6 0% 3. 33/66MHz switching.(factory setting at 66MHz). GA 0: can be set by user(factory setting is per specification). Rear transition module has type AB shrouds (RP3, RP). and all slot have coding key(charcoal) (RP). 6. V(I/O) power switching bus bar is included as standard.(factory setting at +3.3V). Coding key(yellow) is equipped at all slot as standard.(p) 7. FG-SG can be switched. SPB-0CWR3 front side SPB-0CWR3 rear side 9. L x N=K 3.2 Power supply terminal Bus bar Type AB shrouds (RP) BROWN KEY (RP) Type AB shrouds (RP3) mm hard metric connector (P- P) ATX specified power connector

14 Computer Telephony backboard (Hot swap corresponding product) Specification. Board material: Epoxy glass(fr-, 3.2t, 0 layers) 2. Connector: IEC076(2mm hard metrics) 3. Power providing method: Bolting to terminal (8A per terminal) +V, +3.3V, V(I/O), +2V, -2V, GND, FG Telecom Power(-Vbat/-SELVbat) Telecom Ringing Voltage(VRG). Check terminal: PRST, DEG, FAL. Signal line impedance: 6 ( 0%) Order code L N K System slot SPB-0CTR slots SPB-06CTR System slot slots on the right SPB-08CTR slots SPB- CTR * We can accept special order on this product. We also build backboard with different size per request.. System slot( 8 )is assigned on the right side(right system). 2. Rear I/O module can be installed at P3/P/P on system slot. 3. P3 on peripheral slot ( - ) can be used for user I/O.. V(I/O) power switching bus bar is provided as standard.(factory setting at +V). +V and CT coding key is provided as standard. 6. Signal line terminator is provided as standard.(spb-08ctr only) 7. Jumper posts for various setting. 8. Additional power supply terminal as option.(using fasten terminal) 9. GND-earth(FG) connectable. 0. Optional type AB shrouds SPB-08CTR front side L x N=K 3.2 SPB-08CTR rear side Bus bar Power supply terminal P shrouds mm hard metric connector (P-P) Pin assignment P2 P cpci6bit cpci32bit with Hot Swap ATX specified power connector (2 connections max) cpci6bit cpci32bit with Hot Swap P3 shrouds P CT I/O P H.0 (CT Bus) P3 Rear I/O Rear I/O Rear I/O Rear I/O Peripheral slot ( - ) System slot( 8 ) Peripheral slot ( - ) System slot( 8 ) Termination (shot key barrier diode alley) 2

15 PXI backboard Specification. Board material: Epoxy glass(fr-, 3.2t, 0 layers) 2. Connector: IEC076(2mm hard metrics) 3. Power providing method: Bolting terminal(8a per terminal), +V, +3.3V, +2V, -2V, GND 2 ATX power connector(optional) 3 pin DIN connector(optional) Order code SPB-08PXI L N K slots. PICMG2.8 (PXI bus) certified product. 2. Impedance of signal lines are adjusted to 6 0% 3. System slot is assigned at slot(left side) Trigger slot is at slot 2.. V(I/O) voltage is switched by bus bar.. Electrical specification defined by PXI bus is implemented as standard(0mhz reference clock, PXI local bus and PXI start trigger). Circuit for 0MHz reference clock oscillation L Termination (Diode allay) x N=K Power supply terminal Bus bar 2mm hard metric connector (P/P2) 3

16 Bus bridge module Specification. Operating voltage: max) 2. Data bus: primary 6 bits Secondary 6 bits 3. Board material: Epoxy glass(fr-,.6t, 8 layers). Connector: IEC076(2mm hard metrics). Signal line impedance: 6 0% 6. Environment: Operating: Temperature 0-60 Humidity -9%(0 no condense) Storage/Transportation: Temperature 0 to +70 Humidity 0-9%(0 no condense) Order code SPB-6HR2 Notes slots width. Maximum expansion on secondary side is 7 slots. 2. Each power layer is separated between primary side and secondary side & V(I/O) voltage can be set per each segment. 3. GND layer is connected between primary and secondary sides.. Interrupt setting line(int signals) can be set by user.. Slot expansion can be done without losing slot. (SPB- CWER is used) Diagram Primary side connector Arbitration x Arbitration x 7 Clock x 6bits PCI signal PCI-PCI Bridge (2) Clocks x 7 6bits PCI signal Secondary side connector mm hard metric connector (J/J2) Bridge IC

17 Single height extender board Specification. Material: Board/Epoxy glass(fr-,.6t, 6 layers) Rail bracket/aluminum Guide rail/noryl resin(ul9-v0) 2. Applicable board size: H=00mm D=60mm 3. Applicable rack: 3U size rack(d=60mm). Pattern(Inner layer): Power pin is PICMG 2.0 R2. 6bits confirmed. Other pattern are connected in parallel.. Signal line impedance is adjusted to 6 0% 2. Signal termination can be done by attaching off board terminator STB6-CM(optional) at check terminal part. 3. Voltage checking is easy with test pin for voltage checking.. Injection/Eject is easy with injector/ejector support.. Board under test is injected/ejected easily with guide rail. Order code SEC-60CSA J pin assignment CPCI 32 bits J2 pin assignment CPCI 6 bits 32.9 Rail bracket Check terminal connector Extender board J2A J2B P2 30. JA JB P Board under test Guide rail Power check terminal Handle

18 Double height extender board Specification. Material: Board/Epoxy glass(fr-,.6t, 6 layers) Rail bracket/aluminum Guide rail/noryl resin(ul9-v0) 2. Applicable board size: H=233.3mm D=60mm 3. Applicable rack: 6U size rack(d=60mm). Pattern(Inner layer): Power pin is PICMG 2.0 R2. 6bits confirmed. Other pattern are connected in parallel.. Signal line impedance is adjusted to 6 0% 2. Signal termination can be done by attaching off board terminator STB6-CM(optional) at check terminal part. 3. Voltage checking is easy with test pin for voltage checking.. Injection/Eject is easy with injector/ejector support.. Board under test is injected/ejected easily with guide rail. Order code J pin J2 pin J3 pin J pin J pin assignment assignment assignment assignment assignment SEC-60CWA SEC-60CWB SEC-60CWC 32 bits 32 bits 32 bits 6 bits 6 bits 6 bits No connector No connector No connector Parallel Parallel Parallel No connector Parallel Parallel Rail bracket Extender board Board under test Guide rail Check terminal connector Power check terminal Handle 6

19 Attention Attention for safety usage Notes on installation of rack warning Be sure to extract power code before disassembling rack. Never disassemble integrated power supply. It s dangerous. Never apply excessive voltage than specified on input terminal(ac cord). Be sure to connected GND terminal(ac cord) to ground. Be sure to start the recovering process after shutdown the input(ac cord) when protection logic(protect against line short, protect against over current) is activated or fuse is melt down. Be sure to apply power after resolving the cause of the activation of protect logic. Never use other fuse except specified one. Notes Be sure to connect sensing terminal(makes it sensing mode). Use local sensing if you decide not to use remote sensing. Normal voltage is not supplied without this connection.(protect logic may be activated). Factory setting is remote sensing. Be sure to check voltage with loading. Specified voltage may not supplied without loading. Insurance period of system products is year after the purchase. Damage or failure caused by customer s careless usage is out of this insurance even before the expiration of insurance period. Be careful not to hurt your hands or clothes when you try to disassemble rack because they have portion with sharp edge due to the characteristic of metal product. Be sure not to install rack at the environment with high temperature, high himidity and many dust. Be sure not to cover the portion with slit for air flow at installation. Allocate rack keepin some space(over 0mm) against objects around the portion with slit not to cover slit area. Covering slited area causes the increase of inside temperature & this will cause failure. Names of PICMG and CompactPCI, logo of PICMG and CompactPCI are Registered trade mark of PCI Industrial Computers Manufacturers Group. The specification and shape of products may be changed without notice. 7

20