D&I Breakout Panel Installation and Operation Manual. Part Number MN/D-I.IOM Revision 0

Transcription

1 D&I Breakout Panel Installation and Operation Manual Part Number Revision 0

2

3 D&I Breakout Panel Installation and Operation Manual Comtech EF Data is an ISO 900 Registered Company. Part Number Revision 0 August 9, 005. Copyright Comtech EF Data, 005. All rights reserved. Printed in the USA. Comtech EF Data, 4 West th Street, Tempe, Arizona 858 USA, , FAX: 480..

4 Warranty Policy This Comtech EF Data Corporation product is warranted against defects in material and workmanship for a period of one year from the date of shipment. During the warranty period, Comtech EF Data will, at its option, repair or replace products that prove to be defective. For warranty service, the product must be returned to Comtech EF Data, shipping prepaid by the buyer. Return shipping charges for normal surface delivery within the continental U.S. will be paid by Comtech EF Data. For equipment under warranty, the customer is responsible for freight to Comtech EF Data and all related custom, taxes, tariffs, insurance, etc. Comtech EF Data is responsible for the freight charges only for return of the equipment from the factory to the customer. Comtech EF Data will return the equipment by the same method (i.e., Air, Express, Surface) as the equipment was sent to Comtech EF Data. Limitations of Warranty The foregoing warranty shall not apply to defects resulting from improper installation or maintenance, abuse, unauthorized modification, or operation outside of environmental specifications for the product, or, for damages that occur to improper repackaging of equipment for return to Comtech EF Data. No other warranty is expressed or implied. Comtech EF Data Corporation specifically disclaims the implied warranties of merchantability and fitness for particular purpose. Exclusive Remedies The remedies provided herein are the buyer's sole and exclusive remedies. Comtech EF Data Corporation shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contact, tort, or any other legal theory. Disclaimer Comtech EF Data has reviewed this manual thoroughly in order that it will be an easy-touse guide to your equipment. All statements, technical information, and recommendations in this manual and in any guides or related documents are believed reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to be, representations or warranties concerning the products described. Further, Comtech EF Data reserves the right to make changes in the specifications of the products described in this manual at any time without notice and without obligation to notify any person of such changes. If you have any questions regarding your equipment or the information in this manual, please contact the Comtech EF Data Customer Service Department. (For more information, refer to the preface.)

5 Preface About this Manual This manual provides installation and operation information for the EFData D&I breakout panel. This is a technical document intended for earth station engineers, technicians, and operators responsible for the operation and maintenance of the D&I breakout panel. Organization This manual includes the following chapters: Chapter provides an introduction. Chapter provides connector and switch information. Revision Numbering Scheme The following table identifies the revision numbering scheme utilized for EFData installation and operation manuals, addenda, and supplements: Part # Revision Level Description MN/D&I Rev. 0 st edition of the manual. MN/D&I Rev. st revision (nd edition) of the manual. MN/D&I_A Rev. Addendum A Addendum A to Rev. of the manual. MN/D&I_B Rev. Addendum B Addendum B to Rev. of the manual. MN/D&I Rev. nd revision (rd edition) of the manual (includes information from Addenda A and B). MN/D&I_SA Supplement A Supplement A to the manual. (The S in SA designates Supplement. ) Note: This is a limited distribution document. i

6 Preface Conventions Used in this Manual Caution and Warning CAUTION CAUTION indicates a hazardous situation that, if not avoided, may result in minor or moderate injury. CAUTION may also be used to indicate other unsafe practices or risks of property damage. WARNING indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury. WARNING Note NOTE This is the style for a note. European EMC Directive In order to meet the European Electro-Magnetic Compatibility (EMC) Directive (EN550, EN5008-), properly shielded cables for DATA I/O are required. More specifically, these cables must be double-shielded from end-to-end, ensuring a continuous ground shield. The following information is applicable for the European Low Voltage Directive (EN0950): <HAR>! Type of power cord required for use in the European Community. CAUTION: Double-pole/Neutral Fusing ACHTUNG: Zweipolige bzw. Neutralleiter-Sicherung International Symbols: Alternating Current. Fuse. Safety Ground. Chassis Ground. NOTE For additional symbols, refer to Caution and Warning listed earlier in this preface. ii

7 Preface Reporting Comments or Suggestions Concerning this Manual Comments and suggestions regarding the content and design of this manual will be appreciated. To submit comments, please contact the EFData Customer Service Department according to the following information. Customer Service Contact the EFData Customer Service Department for: Product support Information on returning a product Information on upgrading a product Product training Reporting comments or suggestions concerning manuals An EFData Customer Service representative may be reached at: EFData Corporation Attention: Customer Service Department 05 West 5th Place Tempe, Arizona 858 USA (0) (0) 9-90 FAX or, can be sent to the Customer Service Department at: service@efdata.com To return an EFData product (in-warranty and out-of-warranty) for repair or replacement:. Request a Return Material Authorization (RMA) number from the EFData Customer Service Department. Be prepared to supply the Customer Service representative with the model number, serial number, and a description of the problem.. To ensure that the product is not damaged during shipping, pack the product in its original shipping carton/packaging.. Ship the product back to EFData. (Shipping charges should be prepaid.) For more information regarding the warranty policies, refer to the disclaimer page located behind the title page. iii

8 Preface This page is intentionally left blank. iv

9 Table of Contents PREFACE... i About this Manual...i Organization...i Revision Numbering Scheme...i Conventions Used in this Manual...ii Caution and Warning...ii Note...ii European EMC Directive...ii Reporting Comments or Suggestions Concerning this Manual...iii Customer Service...iii CHAPTER. INTRODUCTION... CHAPTER. CONNECTORS AND SWITCHES.... Drop Data Input, Insert Data Output, and Ext. Ref CLK.... Drop Data Output (J).... Insert Data Input (J)....4 Insert Data Output (J4)....5 Drop Data Input (J5) Drop Data Output (J)... 8 v

10 Preface. Insert Data Input (J) Insert Data Output (J8) External Reference Clock (J9) ESC Channel (J0) Faults (J) Data Interface (J)... 0 Figures Figure -. D&I Breakout Panel... Figure -. D&I Daughter Card Schematic... Figure -. D&I Breakout Panel Schematic... 4 Figure -. D&I Breakout Panel Schematic (Cont d)... 5 Tables Table -. D&I Breakout Panel Connectors... Table -. D&I Breakout Panel Switch Selections... vi

11 Chapter. INTRODUCTION The D&I (B-08-5) breakout panel provides standardized interfaces for the D&I capabilities of the modem. The balanced and unbalanced interfaces for drop DATA I/O and insert DATA I/O are provided and are selectable with rear panel DIP switches. This breakout panel is used in : or M:N switching configurations. The D&I breakout panel supports the use of the D&I channel unit in the modem. Refer to Chapter for connector and switch information.

12 Introduction This page is intentionally left blank.

13 Chapter. CONNECTORS AND SWITCHES The locations of the connectors and D&I switches S through S5 are shown in Figure -. Refer to Table - for D&I breakout panel connector information. Refer to Table - for the D&I breakout panel switch selections. The D&I PCB schematic is shown in Figure -. Refer to Figure - for the D&I breakout panel schematic.

14 Connectors ans Switches FRONT VIEW J J DROP INPUT DROP OUTPUT INSERT INPUT J INSERT OUTPUT J4 DROP IN INSERT IN OUT J5 J J OUT J8 EXT REF CLK J9 J0 ESC CHANNEL C G C O N N N ON N MC O D MC O J FAULTS PRI SEC REAR VIEW S OPEN J LOOP 4 NORM S4 S CLOSED OPEN OPEN CLOSED S CLOSED DCE DTE S5 Figure -. D&I Breakout Panel Table -. D&I Breakout Panel Connectors Ref Desig. Connector Type Name J 5-pin D Drop Data Input J 5-pin D Drop Data Output J 5-pin D Insert Data Input J4 5-pin D Insert Data Output J5 BNC Drop Data Input J BNC Drop Data Output J BNC Insert Data Input J8 BNC Insert Data Output J9 BNC Ext. Ref Clock J0 5-pin D ESC Channel J Terminal Block Faults J 50-pin D Data Interface

15 Connectors ans Switches Table -. D&I Breakout Panel Switch Selections Signal Function Name Switch Switch # Position Unbalanced Drop Data Input DDI S, /, 4 ON/OFF Balanced Drop Data Input DDI S, /, 4 OFF/ON Unbalanced Drop Data Output DDO S 5, /, 8 OFF/ON Balanced Drop Data Output DDO S 5, /, 8 ON/OFF Unbalanced Insert Data Input IDI S, /, 4 OFF/ON Balanced Insert Data Input IDI S, /, 4 ON/OFF Unbalanced Insert Data Output IDO S 5, /, 8 OFF/ON Balanced Insert Data Output IDO S 5, /, 8 ON/OFF Unbalanced Ext. Reference Clock EXC S, /, 4 OFF/ON Balanced Ext. Reference Clock EXC S, /, 4 ON/OFF Drop Output/Insert Input Loopback DDO/IDI S4 N/A UP Normal S4 N/A DOWN Drop Data Output DCE/DTE Select DDO S5 N/A UP DCE/DTE S5 N/A DOWN NOTE S through S5 are ON in the down position (toward PCB). J DB5 INSERT INPUT DATA JP J HEADER 8X DB5 DROP DATA INPUT/ INSERT DATA OUTPUT/ EXT REF CLK Figure -. D&I Daughter Card Schematic

16 Connectors ans Switches J5 DROP INPUT DATA T Cont. next page R : XF8 A J DROP DATA OUTPUT T J R : XF8 S5 SW DPDT DROP DATA OUTPUT DCE/DTE SELECT S SW DIP-8 S SW DIP DDI-A DDI-B DDO-A DDO-B EXC-A EXC-B DB5 DROP OUTPUT DATA S4 IDI-A IDI-B J9 EXT REF CLOCK T5 DDO-A R DDO-B : XF8 JP SW DPDT DROP OUTPUT/ INSERT INPUT LOOP HEADER 8X J INSERT INPUT DATA T R : XF8 J8 INSERT OUTPUT DATA T4 R : XF8 J IDO-A IDO-B S SW DIP IDI-A IDI-B IDO-A IDO-B DB5 INSERT OUTPUT DATA Figure -. D&I Breakout Panel Schematic 4

17 Connectors ans Switches 5 PRI_COM A PRI_NO PRI_NC J 8POSTERMBLK TERTXDAT TERRXDAT J0 DB5 ESC DDI-A DDI-B EXC-A P0 P4 4 P8 8 P0 P5 5 P9 9 P0 P P0 0 P04 4 P P P05 5 P8 8 P P0 P9 9 P P0 P40 40 P4 4 P08 8 P4 4 P5 5 P09 9 P4 4 P P0 0 P4 4 P P P44 44 P8 8 P P45 45 P9 9 P P4 4 P0 0 P4 4 P4 4 P P5 5 P48 48 P P P49 49 P P P50 50 J DB50 DDO-A DDO-B IDI-A IDI-B IDO-A IDO-B EXC-B TERTXDAT TERRXDAT DSR RTS/CTS SEC_COM SEC_NO SEC_NC PRI_COM PRI_NC PRI_NO SEC_COM SEC_NO SEC_NC DSR Cont. from previous page Figure -. D&I Breakout Panel Schematic (Cont d)

18 Connectors ans Switches. Drop Data Input, Insert Data Output, and Ext. Ref CLK This signal connection is a 5-pin female D connector (J) located at the front of the breakout panel. Screw locks are provided for mechanical security of the mating connector. Signal Function Name Pin # Ground GND, 4 Insert Data Out IDO A IDO B External Clock EXC A EXC B 8 Drop Data Input DDI A DDI B 9 For J selections, use S, S, and S, located at the rear of the breakout panel. Signal Function Name Switch Switch # Position Balanced Insert Data Output IDO S 5, /, 8 ON/OFF Balanced Drop Data Input DDI S, /, 4 ON/OFF Balanced External Clock EXC S, /, 4 ON/OFF. Drop Data Output (J) The balanced drop data output connection is a 5-pin female D connector located at the front of the breakout panel. Screw locks are provided for mechanical security of the mating connector. Signal Function Name Pin # Ground GND, 4 Drop Data Output DDO A DDO B 9 Drop Data Output DDO A DDO B For J selections, use S and S5 located at the rear of the panel. Signal Function Name Switch Switch # Position Balanced Drop Data Output DDO S5 N/A UP (DCE/DTE Select) Unbalanced Drop Data Output DDO S 5, /, 8 OFF/ON Balanced Drop Data Output DDO S 5, /, 8 ON/OFF NOTE S is ON in the down position (toward PCB).

19 Connectors ans Switches. Insert Data Input (J) The balanced insert data input connection is a 5-pin female D connector located at the front of the breakout panel. Screw locks are provided for mechanical security of the mating connector. Signal Function Name Pin # Ground GND, 4 Insert Data Input IDI A IDI B For J selections, use S located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced Insert Data Input IDI S, /, 4 OFF/ON Balanced Insert Data Input IDI S, /, 4 ON/OFF NOTE S is ON in the down position (toward PCB)..4 Insert Data Output (J4) The balanced insert data output connection is a 5-pin female D connector located at the front of the breakout panel. Screw locks are provided for mechanical security of the mating connector. Signal Function Name Pin # Ground GND, 4 Insert Data Output IDO A IDO B For J4 selections, use S located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced Insert Data Output IDO S 5, /, 8 OFF/ON Balanced Insert Data Output IDO S 5, /, 8 ON/OFF NOTE S is ON in the down position (toward PCB).

20 Connectors ans Switches.5 Drop Data Input (J5) The unbalanced and balanced drop data input connection is a BNC connector located at the front of the breakout panel. For J5 selections, use S located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced Drop Data Input DDI S, /, 4 ON/OFF Balanced Drop Data Input DDI S, /, 4 OFF/ON NOTE S is ON in the down position (toward PCB).. Drop Data Output (J) The unbalanced and balanced drop data output connection is a BNC connector located at the front of the breakout panel. For J selections, use S located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced Drop Data Output DDO S 5, /, 8 OFF/ON Balanced Drop Data Output DDO S 5, /, 8 ON/OFF NOTE S is ON in the down position (toward PCB).. Insert Data Input (J) The unbalanced and balanced insert data input connection is a BNC connector located at the front of the breakout panel. For J selections, use S located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced Insert Data Input IDI S, /, 4 OFF/ON Balanced Insert Data Input IDI S, /, 4 ON/OFF NOTE S is ON in the down position (toward PCB). 8

21 Connectors ans Switches.8 Insert Data Output (J8) The unbalanced and balanced insert data output connection is a BNC connector located at the front of the breakout panel. For J8 selections, use S located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced Insert Data Output IDO S 5, /, 8 OFF/ON Balanced Insert Data Output IDO S 5, /, 8 ON/OFF NOTE S is ON in the down position (toward PCB)..9 External Reference Clock (J9) The unbalanced and balanced external reference clock input is a BNC connector located at the front of the breakout panel. For J9 selections, use S, located at the rear of the panel. Signal Function Name Switch Switch # Position Unbalanced External EXC S, /, 4 OFF/ON Reference Clock Balanced External Reference Clock EXC S, /, 4 ON/OFF NOTE S is ON in the down position (toward PCB)..0 ESC Channel (J0) The ESC Channel interface is a 5-pin female D connector located at the front of the breakout panel. Screw locks are provided for mechanical security of the mating connector. Signal Function Name Pin # Ground GND, Terrestrial Tx Data Terrestrial Rx Data TER TXDAT TER RXDAT Request To Send RTS 4 Clear To Send CTS 5 Data Set Ready DSR NOTE RTS and CTS are looped together on the connector. 9

22 Connectors ans Switches. Faults (J) The Faults connection is an 8-position terminal block located at the front of the breakout panel. Signal Function Name Pin # Ground GND, 5 Primary Common Primary Norm/Open Primary Norm/Closed PRI COM PRI NO PRI NC 4 Secondary Common Secondary Normally Open Secondary Normally Closed SEC COM SEC NO SEC NC 8. Data Interface (J) The data interface connection is a 50-pin female D connector located at the rear of the breakout panel. Screw locks are provided for mechanical security of the mating connector. Signal Function Name Pin # Ground GND, Drop Data Input DDI A DDI B 4 8 External Clock EXC A EXC B 5 9 Insert Data Output IDO A IDO B 0 Drop Data Output DDO A DDO B 8 Terrestrial Tx Data Terrestrial Rx Data TER TXDAT TER RXDAT 5 Insert Data Input IDI A IDI B 9 40 Primary Common Primary Normally Open Primary Normally Closed PRI COM PRI NO PRI NC 0 4 Secondary Common Secondary Normally Open Secondary Normally Closed SEC COM SEC NO SEC NC 44 8 Data Set Ready DSR 48 Terrestrial ESC DSR TER ESC DSR 4 0

23 METRIC CONVERSIONS Units of Length Unit Centimeter Inch Foot Yard Mile Meter Kilometer Millimeter centimeter x inch x foot x yard x meter x 0-4 mile.09 x 0 5. x x 0.0 x 0.09 x 0.09 mm 0.09 kilometer 0. Temperature Conversions Unit Fahrenheit Centigrade Formulas Fahrenheit 0 (water freezes) C = (F - ) * Fahrenheit 00 (water boils) F = (C *.8) Fahrenheit. (absolute 0) Units of Weight Unit Gram Ounce Avoirdupois Ounce Troy Pound Avoir. Pound Troy Kilogram gram oz. avoir oz. troy lb. avoir lb. Troy kilogram.0 x

24 4 WEST TH STREET TEMPE ARIZONA 858 USA PHONE 480 FAX